Sentex Crown Jewel Programming Manual

®

Keypad Programming Manual

3

6

9

#

2

5

8

0

1

4

7

CALLCALL

G UPG UP

3

6

9

#

2

5

8

0

1

4

7

CALLCALL

G UPG UP

The Chamberlain Group

845 Larch Ave.

Elmhurst, IL 60125-1196

www.chamberlain.com

Crown Jewel

Telephone entry system

PAGE 1

Quick Reference

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (✱) to begin again.

The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

PAGE 3

Quick Reference

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (✱) to begin again.

The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

Program Number

26

27

28

29

30

31

32

33 34

35

36

37

38

40

41

42

43

88

89

90 91

92

93

94

95

96

97

7

11

29

-

30

29 18

23

29

28

15

29

30

13

26 21

21

---

5

Disabled

Enabled

00

---

Disabled

20 Seconds

---

Disabled

---

Configure Relay #2 and Status #2

Set the Date and T im

e

Create a Holiday

Setting the Rings Before Answer

Adjust the Sidetone Balance

Restore Facto r y Default s

Reset the Unit

Enable/Disable No- T elco Mod e Change Visitor Response Keys

Enable Direct Commands

Set Alternative Prefixes

Verify Unit Number

Setting the Unit Number

Enable/Disable Unlock Schedules

Set Unlock Schedule for Relay #1

Set Unlock Schedule for Relay #2

Override Answering Service

Erase All T ransaction s

Active/Cancel DND Schedule

Speak Through the Crown Jewel Cycle Relay #1

Cycle Relay #2

Latch Relay #1

Latch Relay #2

Release Relay #1

Release Relay #2

Release Both Relays

26 + (Configuration Number, 0-5) #

27 + (Year, yy) + (Month, mm) + (Current Date, dd) + (Day, 1-7) + (Hour, hh) + (Minutes, mm) #

0

---

28 + (Holiday, 0-9) + (Month, mm) + (Date, dd) #

29 + (Number of Rings Before Answer, 1-19) #

30 # (Unit will emit a tone for 45 seconds)

31 #

32 #

33 + (0 = Disable; 1 = Enable) # 34 + (Activate Main Gate)+ (Activate Auxiliary

Relay) + (Call Wait Toggle) + (Extend Talk Time) + (Hang Up) #

9, 5, 2, 1, *

35 + (Direct Command Number, 0-3) #

36 + (Alternate Prefix, 00-04 or 1n) #

37 # (Unit will emit beeps corresponding with its unit number)

38 + (Unit Number, 1-7) + (Number of Units in Chain, 1-7) #

40 + (Unlock Schedule Mode, 0-1) #

41 + (Days of the Week, 1-7) + (Segment, 1-2) + (Open Time, hhmm) + (End Time, hhmm) + (Holiday, 0-2) #

42 + (Days of the Week, 1-7) + (Segment, 1-2) + (Open Time, hhmm) + (End Time, hhmm) + (Holiday, 0-2) #

43 + (Delay Time in Seconds, 1-99) #

88 + 101010 #

Activate: 89 + (End Time, hhmm) # Cancel: 89 + 99 #

90 # 91 #

92 #

93 #

94 #

95 #

96 #

97 #

Page

Programming Procedure

98

99

22

---

Latch Relay #1 Until

Latch Relay #2 Until

98 + (End Time, hhmm) #

99 + (End Time, hhmm) #

Factory Setting

Description of Task

PAGE 4

Programming Basics

The Crown Jewel can be programmed 2 different ways:

1. Crown Jewel Keypad: You may used the keypad on the front panel.

2. Local/Remote DTMP Phone: You may use the keypad on a local or remote phone to program the system. The unit

response to the DTMF signals generated by your touch-tone phone.

3. Modem Connection to a PC: In order to program the Crown Jewel with a modem connection, your PC MUST be running

Sentex’s Windows®-compatible CJWIN software. (See CJWIN Programming manual for more information.)

The instructions in THIS manual will describe how to program the Crown Jewel from the keypad or local/remote DTMF (Touch-Tone) phone ONLY. For More information check with your installation dealer.

Example: Procedure for Programming the Crown Jewel

1. 2 digit # Programming Number. (See Quick Reference on pages 2-3 for descriptions and procedures.)

2. One or more Data Fields.

3. Pound Key (#) at end of the programming sequence to Save the Data.

NOTES:

• If you make an error during and entry, press the asterisk key(✱) to cancel the step.

• When you correctly enter the entire programming sequence, the unit will respond with 2 short beeps (See System Feedback/Responses (Beeps) see below).

Example of a Programming Sequence: “01 Change the Unit Password”

2 short beeps

Programming Number:

“01” changes or verifies the password.

Data Field:

(The new Password.)

Pound Key:

Saves the Data.

Enter Programming Mode (See page 5)

Exit Programming

Mode (See page 6)

System Feedback/Responses (Beeps)

Programming Responses:

2 Short Beeps: Programming step was valid. 3 Short Beeps: Programming step was exited.

1 Long Beep: Input was not valid. 2 Long Beeps: Duplicate entry code was entered. 3 Long Beeps: Memory is full. 4 Long Beeps: Unit has reset or is powering up. Busy Signal: Line is busy or Do Not Disturb feature is in effect.

Direct Command Responses:

5 Short Beeps: Gate is closing by command. 10 Short Beeps: Gate is opening by command.

Other Responses:

1 Short Beeps: Key was pressed on the main keypad. 10 Beeps: Talk time for a visitor call is ending. The unit will begin to beep when 10 seconds of talk time

remain, beeping once every second.

Ring Back: The unit is ringing the house. High-Low Tones: An alarm condition has been activated. Silence: The keypad has stuck out, unit is being programmed remotely, or an alarm condition exists.

PAGE 5

1. Press

2. Enter the (6) six-digit password. The default is 2 Short Beeps

The unit is now ready to accept programming instructions.

From the Crown Jewel Keypad

High pitch tone stops.

1. When you hear a dial tone, press

2. Enter the (6) six-digit password. The default is

3. Press and the tone will stop.

The unit will emit a high-pitched tone.

The unit is now ready to accept programming instructions.

Unit is ready to accept programming instructions.

Unit #4 (Data field “1A” specifies unit to be programmed) is ready to accept programming instructions.

If multiple Crown Jewel units are sharing the same phone line, then a Unit ID Code (1-7) MUST be entered at this time.

1A.

NOTE: The default setting for each Crown Jewel unit is Unit #1. See page 27 for more information about Multiple Unit Sites.

Single Unit Example:

Multi-Unit Example:

High pitch tone stops.

1 2

1 1A 2

From the Residence Telephone

Unit is ready to accept programming instructions.

Unit #4 (Data field “2A” specifies unit to be programmed) is ready to accept programming instructions.

The unit will emit a high-pitched tone.

NOTE: If the Crown Jewel unit and an answering machine (or answering service) utilize the same telephone line, let the line ring at least (2) two times, hang-up and call back within (1) one minute. The Crown Jewel unit will answer on the second call. If the unit does not answer, you may need to change the ring count (see Set Visitor Ring Sound on page 18.)

If multiple Crown Jewel units are sharing the same phone line, then a Unit ID Code (1-7) MUST be entered at this time. (See page 27 for more information about Multiple Unit Sites).

2A.

When the Crown Jewel picks up the call, you will hear 2 short beeps

2. Press

The unit is now ready to accept programming instructions.

3. Enter the (6) six-digit password. The default is

4. Press and the tone will stop.

1. Dial the residence telephone number

Multi-Unit Example:

High pitch tone stops.

1 2 2A 3

Single Unit Example:

High pitch tone stops.

1 2 3

From a Remote Telephone

Enter Programming Mode - ✱✱✱

PAGE 6

Press on the Crown Jewel keypad and the unit will respond with 3 short beeps when disconneting.•

Press on the telephone and the unit will respond with 3 short beeps when disconneting.

0 0

•

Exit Programming Mode - 00

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (✱) to begin again.

The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

PAGE 7

A relay is a device that reacts to an electric current to activate other devices. Allowing the Crown Jewel to lock or unlock a gate, shut (bypass) alarm contacts, signal an alarm, or turn on a camera wired to a closed-circuit television (CCTV). The relays can be programmed to 5 different modes.

MODES OF OPERATION

Strike Relay: A Strike Relay controls a door or gate by unlocking or opening it. It does not control any other

component associated with a system like alarms, CCTV, etc.

Shunt Relay: A Shunt Relay is normally wired to an alarm and works with strike relays to shunt (bypass) the alarm

when the door is opened with a valid access code. If the door is forced open, the system will not shunt the alarm and the alarm will be triggered.

CCTV Relay: A CCTV relay activates the system’s optional camera. The camera is wired to a closed-circuit

television (CCTV). A camera can be activated when an alarm condition occurs or when a resident enters a valid access code.

Alarm Relay: The Alarm Relay will activate another device, such as a siren, when 3 conditions occur: A door is

opened without a valid access code, A door is open past the allotted time programmed in, or too many invalid codes are tried. Any of these will trigger the alarm relay.

Control Relay: The Control Relay can control another device such as an outdoor or indoor light near the unit. For

example, you can configure the system to run an entry light through a darkened area after a resident enters a valid access code. Then the light would turn off after a specified amount of time.

1. Press

3. Press to save the data

2. Enter Configuration Number:

Sets Relay #2 as an Alarm Type and Status 2 for Position Sense 1)

O = Relay #2 = Control Type; Status 2 = Exit Request 2

(During a visitor call, Relay #2 will activate when the #5 is press from the resident phone, or the relay will activate when the Exit Request Device has been activated.)

1 = Relay #2 = Shunt Type; Status 2 = Position Sense 1

(Relay #2 will activate whenever Relay #1 activates to bypass an alarm sensor.)

2 = Relay #2 = Alarm Type; Status 2 = Position Sense 1 (Relay #2 will activate upon an Alarm Condition.) 3 = Relay #2 = CCTV Type; Status 2 = Position Sense 1; Video On = Manual (Closed-circuit TV will activate when the #5 is pressed from the resident phone,

however, the visitor call will not terminate until access is granted "#9" or call is terminated " ".

4 = Relay #2 = CCTV Type; Status 2 = Position Sense 1; Video On = Immediate (Closed-circuit TV will activate when any key is press on the main keypad.) 5 = Relay #2 = Control Type; Status 2 = Position Sense 1

(During a visitor call, Relay #2 will ONLY activate when the "#5" is press from the resident phone.)

EXAMPLE:

1 2 3

Configure Relay #2 and Status #2 Input - 26

Relay #2 can be configured as a Strike, Shunt, CCTV, Alarm or Control Relay. The Status 2 input can be used as an exit request for the second gate or sensor to detect the closed position of the main gate/door.

FACTORY SETTING: 0 (Relay 2 = Control Type; Status 2 = Exit Request.) NOTE: Relay #1 is configured as a Control Relay and cannot be changed.

Configure Relays

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (✱) to begin again.

The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

PAGE 8

Set Relay Activation Times - 23 and 24

Set the amount of time the relay will remain active between 1-250 seconds.

FACTORY SETTING: 10 Seconds

NOTE: If either relay is connected to a gate operator with a momentary contact closure, set the relay activation time for a

short period of time (i.e. 2 seconds). A longer activation time may cause the gate operator to repeatedly open and close the gate until the activation time expires.

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (

✱

) to begin again. The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

1. Press

2. Enter number of seconds Relay #1 will be active (1-250 Seconds)

3. Press to save the data

EXAMPLE:

1 2 3

Sets Relay #1 to remain active for 35 seconds

1. Press

2. Enter number of seconds Relay #2 will be active (1-250 Seconds)

3. Press to save the data

EXAMPLE:

1 2 3

Sets Relay #2 to remain active for 2 seconds

PAGE 9

Entry Codes

Entry codes are used to open the gate or door using the Crown Jewel keypad without phoning the residence. The Crown Jewel unit can store up to 75 entry codes. To restrict access, you can also program entry codes to activate specific relays and/or grant access during specific Time Zones (Schedules) see page 11. Entry codes are four digits long between 0000 and 9999.

1. Press

2. Enter Entry Code (4-digits)

3. Press

Adds Entry Code "1500".

EXAMPLES:

1 2 3

Create an Entry Code - 03

1. Press

2. Enter Entry Code (4-digits) to be deleted

3. Press

Deletes Entry Code "1500".

EXAMPLE:

1 2 3

Delete an Entry Code - 04

Before adding or modifying Entry Codes, answer the following questions:

• Have you chosen the Entry Code number you will assign? This number will be assigned to a resident. The

resident will enter this number on the unit keypad to prompt the system to grand access.

• Will the Entry Code have Time Zone (Schedule) restrictions? You may assign a Time Zone to an Entry

Code so that it is valid ONLY during specified time frames.

On the Crown Jewel keypad, enter the assigned "Entry Code".

If you make an error entering the code press to cancel

1 2 3

4 5 6

7 8 9

0 #

Resident enters in Entry Code Resident gains access

PAGE 10

IMPORTANT NOTE: This programming step erases ALL of the Entry Codes saved in the Crown Jewel database. They cannot be retrieved unless they are saved to a CJWIN database.

1. Press

2. Enter

3. Press

Delete ALL an Entry Code - 05

1. Press

2. Enter Entry Code

4. Enter Time Zone (1-digit)

(See page 11 for information about Time Zones)

3. Enter one of the following Relay Codes:

5. Press

Sets Entry Code "1500" to cycle relay #1 and be valid during the times set up for Time Zone #2

EXAMPLES:

1 2 3 4 5

Sets Entry Code "1400" to cycle relay #2 and be valid 24 hours a day 7 days a week. If a Time Zone Code is not entered as in the example above, the Entry Code will be assigned the default Time Zone of "0" (Access All Day, everyday)

1 2 3 4

0 = Cycle default relay 5 = Release relay #1 1 = Cycle relay #1 6 = Release relay #2 2 = Cycle relay #2 7 = Release both relays 3 = Latch relay #1 8 = Cycle both relays 4 = Latch relay #2 9 = Latch both relays

Special Entry Code Programming - 34

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (✱) to begin again.

The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

PAGE 11

Time Zones (Schedules) and Holidays

1. Press

2. Enter Time Zone Number (1-7)

3. Enter Segment Number (1-2)

4. Enter Start Time (hhmm)

5. Enter End Time (hhmm)

6. Enter Days of the Week

(To add one or more days to the Time Zone/Segment, press the digit corresponding to the day.)

:

7. Press

Sets Time Zone #5, Segment #1 to start at 8:00 AM and end at 8:00 PM, Monday, Wednesday and Friday.

EXAMPLE:

7321 654

1 = Sunday 2 = Monday 3 = Tuesday 4 = Wednesday 5 = Thursday 6 = Friday 7 = Saturday 8 = Holiday

Create a Time Zone (Schedule) - 25

1. Press

2. Enter Holiday Number (0-9)

3. Enter Month (mm)

4. Enter Date (dd)

5. Press

Create a Holiday - 28

NOTE: To set up a time zone that extends past midnight and into the next day, create one segment that runs until midnight (i.e. 8:00 PM [2000] to 11:59 PM [2359]) and a second segment that starts at midnight on the following day (i.e.: 12:00 AM [0000] to 4:00 AM [0400]).

Holidays are special calendar dates that can be used to modify the Crown Jewel’s functionality. (i.e. Do Not Disturb (DND) Schedules, Gate Unlock Schedules, Time Zones and Entry Codes).

1. Press

2. Enter Year (yy)

3. Enter Month (mm)

4. Enter Day (dd)

6. Enter Hour (hh)

7. Enter Minutes (mm)

8. Press

Sets the Crown Jewel's internal clock to 12:00 PM on Saturday, July 17, 2004.

EXAMPLE:

81

5. Enter Day of the Week

(To add one or more days to the Time Zone/Segment, press the digit corresponding to the day.)

: 1 = Sunday 2 = Monday 3 = Tuesday 4 = Wednesday 5 = Thursday 6 = Friday 7 = Saturday 8 = Holiday

2 3 4 5 6 7

Set the Date and Time - 28

Time Zones (Schedules) allow you to create time periods to grant or deny access to a residence. Time Zones may be assigned to an entry code or relay. You can program 7 Time Zones with 2 Segments for each.

Sets Holiday #5 as January 1st.

EXAMPLE:

5321 4

The Crown Jewel contains an internal clock calendar that automatically keeps time and adjusts for leap year, however, it does NOT adjust for daylight savings time. The calendar also is used for scheduling history, transactions and entry codes.

PAGE 12

Do Not Disturb (DND) Schedules

Do Not Disturb (DND) Schedules prevent visitors from calling the residence phone during a specified time. This feature is ONLY available to the main residence phone, not to other tenants via Dialing Codes.

To Delete Do Not Disturb Schedule

Create a Do Not Disturb (DND) Schedule- 11

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (✱) to begin again.

The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

NOTE: When entering Do Not Disturb (DND) Schedules for multiple days of the week, each day requires a separate entry (Example B).

Deletes Do Not Distrub (DND) Schedule for set for Mondays.

EXAMPLE:

4321

1. Press

2. Day of the week (1-8): 1 = Sunday 2 = Monday 3 = Tuesday 4 = Wednesday 5 = Thursday 6 = Friday 7 = Saturday 8 = Holiday

3. Enter Start Time (hhmm)

4. Enter End Time (hhmm)

5. Enter Holiday option (0-2): 0 = No Schedule on holidays 1 = Use same schedule on holidays 2 = Use schedule #8 when this day falls on a programmed holiday

6. Press

EXAMPLE A:

63421 5

Sets Do Not Disturb (DND) Schedule to be active Mondays and on Holidays that fall on a Monday from 8:00 PM to 11:00 PM .

EXAMPLE B:

Sets Do Not Disturb (DND) Schedule to be active Mondays, Tuesdays and on Holidays that fall on a Monday or a Tuesday from 8:00 PM to 11:00 PM .

Entry #1:

Entry #2:

1. Press

2. Enter day of the week to be deleted (1-8): 1 = Sunday 2 = Monday

3 = Tuesday 4 = Wednesday 5 = Thursday 6 = Friday 7 = Saturday 8 = Holiday

3. Enter "99"

63421 5

4. Press

PAGE 13

1. Press

2. Enable/Disable Do Not Disturb (DND) Schedule (0 = Disable; 1 = Enable)

3. Press

Enables Do Not Disturb (DND) Schedule.

EXAMPLE:

21 3

Enable/Disable Do Not Disturb (DND) Schedule - 12

Manually Activate the Do Not Disturb Feature - 89

1. Press

2. Enter "99"

3. Press

To Manually Deactivate the Do Not Disturb Feature

1. Press

2. Enter End Time (hhmm)

3. Press

EXAMPLE:

1 32

Do Not Disturb (DND) activated manually. Visitor calls will be blocked until 7:00 AM

PAGE 14

Auto Unlock Schedules

The Crown Jewel can automatically active either of it’s two relays. Each day of the week can have up to 2 time segments. On programmed holidays, the schedule can automatically be ignored or changed to the alternate holiday schedule.

1. Press

3. Enter Segment (1-digit; 1 or 2)

4. Enter Start Time (hhmm)

5. Enter End Time (hhmm)

2. Enter Days of the Week:

7. Press

Sets Segment #1 for Relay #1 to open on Thursdays and holidays at 8:00 AM and Close at 8:00 PM.

EXAMPLE:

72 631 54

1 = Sunday 5 = Thursday 2 = Monday 6 = Friday 3 = Tuesday 7 = Saturday 4 = Wednesday 8 = Holiday

6. Enter Holiday option: 0 = No Schedule on holidays 1 = Use same schedule on holidays 2 = Use schedule number 8 when this day falls on a programmed holiday

1. Press

3. Enter Segment (1-digit; 1 or 2)

4. Enter Start Time (hhmm)

5. Enter End Time (hhmm)

2. Enter Days of the Week:

7. Press

Sets Segment #1 for Relay #2 to open on Mondays at 6:00 AM and Close at 10:00 PM.

EXAMPLE:

72 631 54

1 = Sunday 5 = Thursday 2 = Monday 6 = Friday 3 = Tuesday 7 = Saturday 4 = Wednesday 8 = Holiday

6. Enter Holiday option: 0 = No Schedule on holidays 1 = Use same schedule on holidays 2 = Use schedule number 8 when this day falls on a programmed holiday

Set Auto Unlock Schedules- 41 & 42

PAGE 15

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (

✱

) to begin again. The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

Enables Unlock Schedules

3

EXAMPLE:

51

1. Press

2. Enter Unlock Schedule Mode (0-1) 0 = Disable Unlock Schedules 1 = Enable Unlock Schedules

3. Press

Enable/Disable Auto Unlock Schedules- 40

Delete Auto Unlock Schedules- 41 & 42

FACTORY SETTING: Disabled

1. Press

2. Enter Days of the Week: 1 = Sunday 5 = Thursday

2 = Monday 6 = Friday 3 = Tuesday 7 = Saturday 4 = Wednesday 8 = Holiday

3. Enter Segment (1-digit; 1 or 2)

4. Enter "99"

5. Press

EXAMPLE:

3

Deletes Thursday Unlock Schedule Segment #1 for Relay #1

1. Press

2. Enter Days of the Week: 1 = Sunday 5 = Thursday

2 = Monday 6 = Friday 3 = Tuesday 7 = Saturday 4 = Wednesday 8 = Holiday

3. Enter Segment (1-digit; 1 or 2)

4. Enter "99"

5. Press

EXAMPLE:

3

Deletes Monday Unlock Schedule Segment #1 for Relay #2

52 41

PAGE 16

Call Forwarding

1. Press

2. Enable/Disable Call Forwaring Mode: 0 = Disable Call Forwarding 1 = Enable Call Forwarding 2 = Enable Scheduled Call Forwarding

3. Press

Enables the Call Fowarding feature.

EXAMPLE:

31 2

Enabling/Disabling Call Forwarding - 13

The Call Forwarding feature redirects visitor calls to an outside telephone number instead of ringing the house. The forwarding number is a regular phone number of up to 12-digits in length. You may also attach one of the following features to a forwarding number:

• An extension of an automated switch board

• An extension (up to 6 digits) that the visitor can dial from the unit’s keypad.

1. Press

2. Enter Call Forwarding Telephone number (up to 12 digits)

3. Press

Sets the Call Forwarding number as 555-1212.

EXAMPLE:

31 2

1. Press

2. Enter “00”

3. Press

Setting the Call Forwarding Number - 14

1. Press

2. Enter “00”

3. Press

Delete Call Forwarding Number - 14

NOTE: During a Call Forwarding call, the visitor will hear normal telephone line sounds, however, they will not hear the number being dialed.

FACTORY SETTING: 0 (Disabled) NOTE: To use the Call Forwarding feature, you MUST program a Call Forwarding Telephone Number..

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (

✱

) to begin again. The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

PAGE 17

1. Press

2. Enter the Extension Number (up to 6-digits)

3. Press

Sets the Call Forwarding Extension Number as 1234.

EXAMPLE:

31 2

Setting the Call Forwarding Extension - 16

When the Call Forwarding feature is enabled, the Crown Jewel is able to dial an extension number (up to 6-digits).

1. Press

2. Enter Delay amount (0-59 seconds) (0 = Disables Extension dialing)

3. Press

Sets a pause of 30 seconds between the Call Forwarding number and the Call Forwarding Extension number.

EXAMPLE:

31 2

Setting the Call Forwarding Extension Delay - 15

1. Press

5. Enter Holiday Option 0 = No Schedule on Holidays 1 = Use Same Schedule on Holidays 2 = Use Schedule Number 8 when this day falls on a Programmed Holiday

3. Enter Start Time (hhmm)

4. Enter End Time (hhmm)

2. Enter Days of the Week

(To add one or more days to the Time Zone/Segment, press the digit corresponding to the day)

:

6. Press

Enables the Call Forwarding Schedule to contact the Call Forwaring Number on Thursdays from 9:00 AM to 5:00 PM excluding Holidays.

EXAMPLE:

621 543

1 = Sunday 2 = Monday 3 = Tuesday 4 = Wednesday 5 = Thursday 6 = Friday 7 = Saturday 8 = Holiday

Set the Call Forwarding Schedule - 18

Program calls to be forward during specified times and days.

PAGE 18

Visitor Calls

When a visitor contacts a resident with the Crown Jewel , the resident can preform various functions using their touch-tone phone. The default settings are as follows:

1. Press

2. Enter Ring Type (Single Ring [1] or Double Ring [2]

3. Press

Set Visitor Call Ring Sound - 06

Extends Talk Time

Hang Up and Deny Access to the Visitor

Toggles Between Visitor and Another Phone Call

ABC

Activates Relay #2

JKL

Activates Relay #1

WXYZ

KEYS ON RESIDENT'S TELEPHONE

1. Press

2. Enter key that will activate Relay #1 (0-9 or )

3. Enter key that will activate Relay #2 (0-9 or )

4. Enter key that will toggle Call Waiting (0-9 or )

5. Enter key that will extend Talk Time (0-9 or )

6. Enter key that will Hang Up and Deny Access to Visitor (0-9 or )

7. Press

Changes the phone key that operates Relay #1 to "1", Relay #2 to "2", the phone key that toggles between calls to "6", "7" extends talk time and "8" hangs up and denies access to the visitor.

NOTE: The asterisk key (

) may be assigned to a specific phone key response, therefore, you will be UNABLE

to cancel a command in this programming step.

EXAMPLE:

2 3 4 5 6 71

Change the Visitor Call Response Keys - 34

1. Press

2. Enter number of rings (1-24)

3. Press

Set Max Visitor Call Ring Count - 12

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (✱) to begin again.

The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

Sets number of rings (1-24) the unit will allow before it disconnects the call. FACTORY SETTING: 12 Rings.

FACTORY SETTING: 2 (Double Ring)

Sets the visitor ring to Single Ring. The phone will ring once every 6 seconds during a visitor call.

EXAMPLE:

2 31

Sets the number of rings before the Crown Jewel disconnects to 10 rings.

EXAMPLE:

2 31

PAGE 19

1. Press

2. Enter Number of Seconds (15-250 Seconds)

3. Press

Sets Visitor Talk Time to 2 minutes (120 seconds).

EXAMPLE:

2 31

Set Visitor Talk Time - 90

Set the maximum length of time (15-250 seconds) for a call made by a visitor from the Crown Jewel unit.

FACTORY SETTING: 90 Seconds

NOTE: Talk time does not begin until the visitor call is answered by the resident’s phone. When calling a Call Forwarding

number, the talk time starts immediately after the phone number is dialed.

1. Press

2. Enable/Disable Pulse Dial mode: 0 = Disable Pulse Dial mode 1 = Enable Pulse Dial mode

3. Press

Disables Pulse Dial mode.

EXAMPLE:

2 31

Enable/Disable Pulse Dial Activation - 09

You can enable a resident’s pulse (rotary) telephone to activate Relay #1 by dialing “9”. Pulse dialing CANNOT be used for any other direct commands, programming or visitor responses. FACTORY SETTING: 0 Disabled

1. Press

2. Enable/Disable Call Waiting mode: 0 = Disable Pulse Dial mode 1 = Enable Pulse Dial mode

3. Press

Disables Call Waiting mode.

EXAMPLE:

2 31

Enable/Disable Call Waiting - 10

FACTORY SETTING: 1 Enabled

NOTE: This feature applies only to calls made to the main residence phone, not to other tenants via dialing codes.

PAGE 20

1. Press

2. Enter Dialing Code Number (1-3)

3. Enter Telephone Number Crown Jewel will dial (up to 12 digits)

4. Press

Sets Dialing Code #2 to dial 555-1234 when #2 is press on the Crown Jewel Keypad.

EXAMPLE:

3 421

Visitor Calls to Other Tenants (Dialing Codes) - 19

This feature allows a visitor to place a call to a location other than the main residence by pressing 1#, 2# or 3# on the Crown Jewel keypad.

1. Press

2. Enter the Maximum Number of Digits the Visitor may dial (0-6 digits; 0 = Disabled)

3. Press

Sets the Maximum Number of Digits in the Extension Number to 4-Digits.

EXAMPLE:

321

Set Maximum Number of Digits Visitor May Dial - 17

Program the maximum number of digits a visitor may enter on the unit’s keypad after the visitor call has been answered.

FACTORY SETTING: 0 (Disabled)

PAGE 21

Direct Commands

Unit MUST be in programming mode in order to use Direct commands.(For information about using direct commands from a resident’s phone see pages 23-24.

1.

Select one of the following:

CYCLE RELAY 1:

Cycles relay #1. Typically used to momentarily open door/gate..

1. Press then

CYCLE RELAY 2:

Cycles relay #2. Typically used to momentarily open door/gate.

1. Press then

LATCH RELAY 1 OPEN:

Latches relay #1 open. Typically used to keep relay #1 open for unknown amount of time.

1. Press then

LATCH RELAY 2 OPEN:

Latches relay #2 open. Typically used to keep relay #1 open for unknown amount of time.

1. Press then

RELEASE RELAY 1:

Release relay #1 to its default status. Used to override existing unlock schedules.

1. Press then

RELEASE RELAY 2:

Release relay #2 to its default status. Used to override existing unlock schedules.

1. Press then

RELEASE BOTH RELAYS:

Releases both relay #1 and #2 to its default status. Used to override existing unlock schedules.

1. Press then

Direct Commands - 91-97

EXAMPLE A:

1

Runs complete cycle on relay #1.

Relay will activate now.

EXAMPLE B:

Relay will latch open now.

1

Latches relay #2 open.

PAGE 22

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (✱) to begin again.

The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

Direct Commands - 98-99

Example:

LATCH RELAY #1 UNTIL SPECIFIED TIME

1. Press

2. Enter End Time (hhmm)

3. Press

Latches relay #1 open until the time of day specified. Typically used to temporarily extend an unlock schedule.

Latches relay #1 open until 12:00 PM.

LATCH RELAY #2 UNTIL SPECIFIED TIME

1. Press

2. Enter End Time (hhmm)

3. Press

Relay will latch open now.

321

Latches relay #2 open until the time of day specified. Typically used to temporarily extend an unlock schedule.

Relay will latch open now.

321

Latches relay #2 open until 10:00 PM.

PAGE 23

With the Direct Command feature, you can perform various functions (e.g., unlock a door) from you phone. This feature is ONLY available for a single family residence or a manager’s phone sharing a phone line with the Crown Jewel.

1. Press

3. Press to save the data

2. Direct Command Number (0-3)

The unit will receive direct commands from both the residence and a remote phone.

EXAMPLE:

1 2 3

O = Disable Direct Commands 1 = Enables Direct Commands from residence phone only 2 = Enables Direct Commands from a remote phone only 3 = Enables Direct Commands from residence or remote phone

Enable or Disable Direct Commands -35

When enabled it allows the resident to control the system’s relays from a touch tone phone.

FACTORY SETTING: Enabled.

Direct Commands from Resident’s Phone

The following commands are carried out by simply picking up the residence telephone and dialing the following key combinations.

IMPORTANT NOTE: These steps will override any existing unlock schedules for the day they are entered.

NOTE: Some areas of the country have a phone company that makes use of the “#” or “✱” key as a code to invoke a special

function. If this is true of your area, you can choose an alternate direct command prefix that uses a number followed by a “#” key. If you wish to uses this feature, please refer to Setting Alternate Prefixes, page 29.

Continued on next page.

Various Direct Commands from the Resident’s Telephone - 91-97

1. Press from the residence phone.

The unit is now prepared to accept a direct command.

2.

Select one of the following options:

A.

CYCLE RELAY 1:

CYCLE RELAY 2:

B.

C.

LATCH RELAY 1 OPEN:

D.

LATCH RELAY 2 OPEN:

Press then

Cycles relay #1. Typically used to momentarily open a door/gate for a visitor without having the visitor initiate a call.

Press then

Cycle relay #2. Typically used to momentarily open a door/gate for a visitor without having the visitor initiate a call.

Press then

Latches relay #1 open, Typically used when the gate/door needs to be kept open for an unknown amount of time.

Press then

Latches relay #2 open, Typically used when the gate/door needs to be kept open for an unknown amount of time.

PAGE 24

RELEASE BOTH RELAYS:

Press then

Releases both relay #1 and #2 to its default status. Used to override existing unlock schedules.

RELEASE RELAY 2:

Release relay #2 to its default status. Used to override existing unlock schedules.

Press then

RELEASE RELAY 1:

Press then

Release relay #1 to its default status. Used to override existing unlock schedules.

unknown amount of time.

Cycles relay #1.

Relay will activate now.

EXAMPLE A:

1 2

Latches relay #1 open.

Relay will latch open now.

EXAMPLE B:

1 2

E.

F.

G.

Various Direct Commands from the Resident’s Telephone - 91-97 (Continued)

NOTE: If the Crown Jewel unit you wish to give a Direct Command to is part of a multi-link chain you must enter the Crown Jewel Unit Number before entering the command number.

Cycles relay #1 on Crown Jewel Unit # 5 (Data field #2 designates which unit is to respond to the direct command entered).

Relay will activate now.

EXAMPLE:

1 3

2

Latches relay #1 open until 11:00 AM.

Relay will latch open now.

1 2 3

Various Direct Commands from the Resident’s Telephone - 98 & 99

Multi-Unit Sites and Direct Commands from the Resident’s Telephone

Example:

Relay will latch open now.

Latches relay #2 open until 10:00 PM.

1 2 3

Example:

LATCH RELAY #1 UNTIL SPECIFIED TIME

1. Press

2. Press

3. Enter End Time (hhmm)

4. Press

Latches relay #1 open until the time of day specified. Typically used to temporarily extend an unlock schedule.

LATCH RELAY #2 UNTIL SPECIFIED TIME

1. Press

2. Press

3. Enter End Time (hhmm)

4. Press

Latches relay #2 open until the time of day specified. Typically used to temporarily extend an unlock schedule.

PAGE 25

1. Press

2. Enter new Password (Must be 6 digits)

3. Press

Changes the unit password to # 123456.

EXAMPLES:

1 2 3

Change the Unit Password - 01

Security Features

2 3

1. Press

2. Enter new Password (Must be 6 digits)

3. Press

Two Short Beeps: Indicates the number matches the password programmed for the selected Crown Jewel unit. 1 Long Beep: Indicates that the number does NOT match the password programmed to the Crown Jewel unit.

If this occurs DO NOT exit programming. Follow the steps in "Change the Unit Password" and then reverify it.

EXAMPLES:

1

Verify Unit Password - 02

Sets the Crown Jewel Keypad so it will stop accepting codes after 3 unsuccessful attempts.

1. Press

2. Enter Number of Errors for the Crown Jewel Keypad (0-9; 0 = No Limit)

3. Enter Number of Errors for the Secondary Keypad (0-9; 0 = No Limit)

NOTE: If no Secondary Keypad is present press #.

4. Press

EXAMPLES:

1 2 3

Set Maximum Number of Keypad Errors - 20

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (✱) to begin again.

The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

2. Press from the residence phone.

3. Press

1. Press from the residence phone.

The unit is now prepared to accept a direct command.

0

9

WXY

Z

PAGE 26

Speak Through the Crown Jewel Speaker - 90

Sets the Crown Jewel Keypad so it will stop accepting codes after 3 unsuccessful attempts.

1. Press

2. Enter Alarm Call Number (up to 12 digits) or enter "00" to contact the residents telephone.

3. Press

EXAMPLES:

1 2 3

Set Alarm Call Number - 22

Sets the Crown Jewel unit to make an alarm call when the door is forced open or the keypad has "Struck-Out".

1. Press

2. Enter Alarm Code Mode (0-3) 0 = Disables Alarm Call 1 = Unit will make an alarm call when the door is forced open 2 = Unit will make an alarm call when a keypad has "Stuck-Out" 3 = Unit will make and alarm call when the door is forced open or when the keypad has "Struck-Out"

3. Press

EXAMPLES:

1 2 3

Enable/Disable Alarm Call- 21

1. Press from the residence phone ONLY.

4. Press . Then hang up the telephone.

2. Enter Ring Digit (1-4) 1 = Single Ring 2 = Double Ring 3 = Triple Ring 4 = Quadruple Ring

Using the In-House Paging Feature - ##0

Any telephone connected to the Crown Jewel will ring twice until the telephone receiver is picked up.

EXAMPLE:

1 2 3

This direct command will cause any telephone connected to the Crown Jewel’s phone line to give a distinctive ring.

This direct command allows the user to speak though the Crown Jewel speaker to greet visitors, ward off vandals, etc.

Program the phone number to call in case of an alarm condition. When you pick up the phone, you will hear continuous hi-low tones indicating an alarm condition. FACTORY SETTING: Disabled

This terminates automatically in 60 seconds unless you hang up the line sooner. You can extend the talk time by pressing "1" on your phone.

PAGE 27

Programming Multiple Units

2. Press . The unit will beep twice again.

1. Dial the residence telephone number When the Crown Jewel picks up the call, the unit will beep twice.

6. Press . The tone will stop and the Crown Jewel unit is ready for programming

4. Enter Unit ID Code (1-7)

5. Enter Unit Password (6-digits). The unit will emit a high-pitched tone

3. Press

Enters unit #1 into programming mode. Unit #1 is now ready to receive programming input.

EXAMPLE:

1 2 543 6

Using a Remote Telephone

1. Press on the resident phone

4. Press . The tone will stop and the Crown Jewel unit is ready for programming

2. Enter Unit ID Code (1-7)

3. Enter Unit Password (6-digits). The unit will emit a high-pitched tone

Enters unit #2 into programming mode. Unit #2 is now ready to receive programming input.

EXAMPLE:

3421

Using the Resident’s Telephone

Multiple Unit Installations

Up to seven (7) Crown Jewels can be installed on a single telephone line. Each unit must have a unique number from 1-7. Visitor calls can only be taken one at a time. For example: if you take a visitor call from the main gate (unit #1) and a visitor attempts to call from a rear gate (unit #2), you will not be notified until the first call is disconnected. However, if you are making a regular phone call, the call waiting feature will operate normally.

When you program the Crown Jewel from the residence telephone or a remote telephone, you MUST include the unit ID code.

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (

✱

) to begin again. The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

PAGE 28

1. Press

4. Press

2. Enter Unit ID Code [Unit Number] (1-7)

3. Enter total number of units in chain (2-7)

Sets the Unit ID Code as "#5" in a chain of "7" Crown Jewel units.

EXAMPLE:

1 2 3 4

Set the Unit Number- 38

1. Press

2. Press

Verify the Unit Number - 37

Adding or removing Crown Jewels will require the Unit ID’s to be re-entered. The Unit ID can ONLY be programmed using the Crown Jewel keypad.

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (

✱

) to begin again. The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

The unit will respond with the number of beeps corresponding to its unit number.

PAGE 29

after 6 rings from a remote telephone.

1. Press

2. Enter Alternate Prefix Mode 00 = To enter Direct Commands use "##"; Programming use " " 01 = To enter Direct Commands use a combination of 2 keys (i.e. "# " or " #"); Programming use a combination of three keys (i.e. "# #" or " # ") 02 = To enter Direct Commands use " "; Programming use " " 03 = To enter Direct Commands use "##; Programming use "##" 04 = Resident will NOT be able to program from their telephone or use Direct Commands 1[N] = To enter Direct Commands use "[N]#"; Programming use "[N][N] ". ([N] = Any number (1-9) on the telephone keypad.)

3. Press

Sets the Alternate Prefix to enter Direct Commands to "#

" or "

#"; and Programming to "#

#" or "

#

".

EXAMPLE:

21 3

1. Press

2. Enter Number of Rings (1-19)

3. Press

Rings Before Answer - 29

Other System Settings

1. Press

2. Enter No-Telco Mode (1-digit) 0 = Disables No-Telco Mode 1 = Enables No-Telco Mode

3. Press

Enable/Disable the No-Telco Mode- 33

Enables No-Telco Mode

EXAMPLE:

21 3

1. Press

2. Enter Delay Time (1-99 seconds)

3. Press

Override Telephone Company Answering Service- 43

Sets the answering service delay to 15 seconds.

EXAMPLE:

21 3

Sets the number of rings before the Crown Jewel will answer a call from a remote telephone. If you have an answering machine (or answering service) attached to the same telephone line as the unit, set the Crown Jewel count for two (2) or more rings higher than the answering machine/service count.FACTORY SETTING: 5 Rings

The Crown Jewel unit will answer the call after 6 rings from a remote telephone.

EXAMPLE:

21 3

Set Alternate Prefix - 36

When you press either “##” or “QQQ” on the resident phone, the Crown Jewel will look for Direct Commands or Programming and it disconnects the phone line and waits for a command. Some Telephone companies require “#” and “✱”. FACTORY SETTING: 00 (“##” = Direct Commands; “✱✱✱ = Programming).

No-Telco mode is used when a unit is NOT using a phone line. After enabling the “No-Telco” mode, Step #32 -”Reset the Unit” MUST be performed. FACTORY SETTING: 0 (Disabled)

To override the answering service, dial the number attached to your unit, let the phone line ring once or twice and disconnect the call. After a few seconds redial. The Crown Jewel will answer immediately. FACTORY SETTING: 20 seconds

PAGE 30

1. Press

2. Press

1. Press

2. Press

Reset the Unit - 32

Restore Factory Settings - 31

Reset/Restore the Crown Jewel Unit

1. Press

3. Press

2. Press

Reset System Memory- 31

1. Press

3. Press

2. Press

Erase ALL Transactions - 88

This will reset the unit without disconnect the power. if you MUST reset the unit contact your installing dealer. This may indicate a larger problem with the system or installation.

PROCEED WITH CAUTION! When performing any of the following programming steps, information will be deleted from the system. You cannot retrieve the deleted information unless the information is saved in the CJWIN software.

When this step is initiated, the relays that were latched (timed or untimed) before this step, will become unlatched. Entry codes and schedules will not be reset.

IMPORTANT NOTE: Once the pound key (#) is pressed the unit will beep once, reset, exit out of the programming mode and beep 4 times.

This will reset the Crown Jewel unit to factory defaults. ALL data will be deleted from the Crown Jewel system. Data will need to be programmed.

This will erase ALL of the transactions that are currently stored in the system.

IMPORTANT NOTES: If you make an error during an entry, press the asterisk key (✱) to begin again.

The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc.) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid.

This document is protected by copyright and may not be copied or adapted without the prior written consent of The Chamberlain Group. This documentation contains information proprietary to The Chamberlain Group and such information may not be distributed without the prior written consent of The Chamberlain Group. The software and firmware included in the Sentex product as they relate to this documentation are also protected by copyright and contain information proprietary to The Chamberlain Group.

Visit Sentex on the web at:

www.chamberlain.com

For technical support, please contact your local Chamberlain dealer.

Sentex Crown Jewel Programming Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

Quick Reference

Programming Basics

Configure Relays

Entry Codes

Time Zones (Schedules) and Holidays

Do Not Disturb (DND) Schedules

Call Forwarding

Visitor Calls

Direct Commands

Direct Commands from Resident’s Phone

Security Features

Multiple Unit Installations

Other System Settings

Reset/Restore the Crown Jewel Unit