Sentera Controls MTP-D010 Series, MTP-D010-AT, MTP-D010-BT Mounting And Operating Instructions

ACTIVE
MTP-D010
Mounting and operating instructions
POTENTIOMETER
ACTIVE
MTP-D010
POTENTIOMETER
Table of contents
SAFETY AND PRECAUTIONS 3
INTENDED AREA OF USE 4
TECHNICAL DATA 4
STANDARDS 4
OPERATIONAL DIAGRAMS 5
WIRING AND CONNECTIONS 5
MOUNTING INSTRUCTIONS IN STEPS 5
VERIFICATION OF INSTALLATION INSTRUCTIONS 7
TRANSPORT AND STORAGE 7
WARRANT Y AND RESTRICTIONS 7
MAINTENANCE 7
MIW-MTP-D010-AT-BT-EN-000 - 06 / 02 / 2019 2 - 7
www.sentera.eu
ACTIVE
MTP-D010
POTENTIOMETER
SAFETY AND PRECAUTIONS
Read all the information, the datasheet, mounting and operating instructions and study the wiring and connection diagram before working with the product. For personal and equipment safety, and for optimum product performance, make sure you entirely understand the contents before installing, using, or maintaining this product.
For saf ety and li censing (CE ) reasons , unauthor ised conver sion and/ or modi fication s of the product are inadmissible.
e product should not be exposed to abnormal conditions, such as: extreme temperatures, direct sunlight or vibrations. Long-term exposure to chemical vapours in high concentration can affect the product performance. Make sure the work environment is as dry as possible; avoid condensation.
All installations shall comply with local health and safety regulations and local electrical standards and approved codes. is product can only be installed by an engineer or a technician who has expert knowledge of the product and safety precautions.
Avoid contacts with energised electrical parts. Always disconnect the power supply before connecting, servicing or repairing the product.
Always verify that you apply appropriate power supply to the product and use appropriate wire size and characteristics. Make sure that all the screws and nuts are well tightened and fuses (if any) are fitted well.
Recycling of equipment and packaging should be taken into consideration and these should be disposed of in accordance with local and national legislation/regulations.
In case there are any questions that are not answered, please contact your technical support or consult a professional.
MIW-MTP-D010-AT-BT-EN-000 - 06 / 02 / 2019 3 - 7
back to the table of contents
www.sentera.eu
MTP-D010
PRODUCT DESCRIPTION
ARTICLE CODES
ACTIVE POTENTIOMETER
MTP-D010 potentiometer series are intended for direct control of EC fans / motors and actuators. ey require a supply voltage of 3—15 VDC and provide a stepless output signal that can be set by a rotary knob within a range adjustable via two trimmers for Vmin (10—70 % Vin) and Vmax (30—100% Vin). ey are suitable for applications where a DC control signal is required. e -AT version features an off position, while -BT provides control within the range Vmin—Vmax. eir enclosures are splash-proof and suitable for both inset and surface mounting.
Code Output Off position
MTP-D010-AT 0, Vmin—Vmax yes
MTP-D010-BT Vmin—Vmax no
INTENDED AREA OF USE
TECHNICAL DATA
Applications where a DC control signal is required
For indoor use only
Power supply: 3—15 VDC
Output:
MTP-D010-AT: 0, Vmin—Vmax
MTP-D010-BT: Vmin—Vmax
Load: RL ≥ 2 kΩ
Vmin: 10—70 % Vin
Vmax: 30—100% Vin
Enclosure:
External: ASA, white-ivory (RAL 9010), IP54 (according to EN 60529)
Internal: polyamide, white-ivory (RAL 9010), IP44 (according to IEC 60335)
Operating ambient conditions:
temperature: 0—40 °C
rel. humidity: < 100 % rH (non-condensing)
Storage temperature: -10—55 °C
STANDARDS
Low Voltage Directive 2014/35/EC
EMC Directive 2014/30/EC
WEE E Di rective 2012/19/EU
RoHs Directive 2011/65/EU
MIW-MTP-D010-AT-BT-EN-000 - 06 / 02 / 2019 4 - 7
back to the table of contents
www.sentera.eu
ACTIVE
MTP-D010
POTENTIOMETER
OPERATIONAL DIAGRAMS
MTP-D010-AT MTP-D010-BT
Output, VDC
100 % Vin
Vmax
70 % Vin
100 % Vin
70 % Vin
Output, VDC
Vmax
Vmin
30 % Vin
10 % Vin
Min.
O
Potenometer posion
On
Max
WIRING AND CONNECTIONS
Vin (+) Supply voltage (3—15 VDC)
Vin(-) Supply voltage, ground
Vout (-) Output, ground
Vout (+) Output voltage
Connections Cable cross section: max. 2,5 mm
MOUNTING INSTRUCTIONS IN STEPS
Before you start mounting your potentiometer, read carefully “Safety and Precautions” and follow the steps:
For inset mounting
Vmin
10 % Vin
30 % Vin
Min
Potenometer posion
²
Max
1. Remove the knob by turning it to the right until it pops out.
2. Unscrew the loose nut to remove the cover of the external enclosure.
3. Do the wiring according to the wiring diagram (see Fig. 1 Wiring and connections).
4. Mount the internal enclosure into the wall according to the mounting dimensions
shown in Fig. 2 Mounting dimensions - inset mounting.
Fig. 1 Wiring and connections
Vmin adjustment
trimmer
Supply voltage
( 3—15 V DC )
MIW-MTP-D010-AT-BT-EN-000 - 06 / 02 / 2019 5 - 7
www.sentera.eu
Vmax adjus tment
trimmer
Output:
-A T: 0, Vmin—Vmax
-B T: Vmin—Vmax
back to the table of contents
26 33
82
89
62
60
82
89
69
82
ACTIVE
MTP-D010
Fig. 2 Mounting dimensions - inset mounting
POTENTIOMETER
50
62
50x50
NOTE
Fig. 3 Mounting dimensions - surface mounting
Mount the unit so that the terminal block and connections are at the lower side.
5. Adjust the Vmin and Vmax trimmers.
6. Mount back the cover and secure it with the nut.
7. Put back the knob and turn it to off position (-AT version) or minimum position
(-BT version).
8. Turn on the power supply.
For surface mounting
1. Remove the knob by turning it to the right until it pops out.
2. Unscrew the nut to remove the cover of the external enclosure.
3. Mount the external enclosure onto the surface by means of screws and dowels
(notincluded in the set) adhering to the mounting dimensions shown in Fig. 3
Mounting dimensions - surface mounting.
62
62
4. Insert the cables through the grommets.
5. Do the wiring according to the wiring diagram (see Fig. 1 Wiring and connections).
6. Insert the internal enclosure into the external one and fix it using the screws and
washers included in the set.
NOTE
MIW-MTP-D010-AT-BT-EN-000 - 06 / 02 / 2019 6 - 7
Mount the unit so that the terminal block and connections are at the lower side.
7. Mount back the cover and secure it with the nut.
8. Put back the knob and turn it to off position (-AT version) or minimum position
(-BT version).
9. Turn on the power supply.
www.sentera.eu
back to the table of contents
MTP-D010
ACTIVE POTENTIOMETER
NOTE
A 5 mm hole can be drilled at the bottom of the external enclosure to drain the condensed water.
VERIFICATION OF INSTALLATION INSTRUCTIONS
ATTENTION
Use only tools and equipment with non-conducting handles when working on electrical devices.
In case of faulty operation, please check if:
the right voltage is applied;
all connections are correct;
the regulated device is functioning.
TRANSPORT AND STORAGE
Avoid shocks and extreme conditions; stock in original packing.
WARRANTY AND RESTRICTIONS
MAINTENANCE
Two years from the delivery date against defects in manufacturing. Any modifications or alterations to the product after the date of publication relieve the manufacturer of any responsibilities. e manufacturer bears no responsibility for any misprints or mistakes in this data.
In normal conditions this product is maintenance-free. If soiled, clean with a dry or damp cloth. In case of heavy pollution, clean with a non-aggressive product. In these circumstances the unit should be disconnected from the supply. Pay attention that no fluids enter the unit. Only reconnect it to the supply when it is completelydry.
MIW-MTP-D010-AT-BT-EN-000 - 06 / 02 / 2019 7 - 7
back to the table of contents
www.sentera.eu
Loading...