Sentera MTY-0-15-AT, MTY-0-05-AT, MTY-0-25-AT, MTX-0-15-AT, MTX-0-05-AT Mounting And Operating Instructions

Mounting and operating instructions

MT

ELECTRONIC FAN SPEED
CONTROLLER

www.sentera.eu

MIW-MTX-EN-000 - 02 / 12 / 2015 2 - 7

back to the table of contents

Table of contents

SAFETY AND PRECAUTIONS 3

PRODUCT DESCRIPTION 4

ARTICLE CODES 4

INTENDED AREA OF USE 4

TECHNICAL DATA 4

STANDARDS 4

OPERATIONAL DIAGRAMS 5

WIRING AND CONNECTIONS 5

MOUNTING INSTRUCTIONS IN STEPS 5

OPERATING INSTRUCTIONS 7

TRANSPORT AND STOCK KEEPING INFORMATION 7

WARRANTY INFORMATION AND RESTRICTIONS 7

MAINTENANCE 7

MT

ELECTRONIC FAN SPEED
CONTROLLER

www.sentera.eu

MIW-MTX-EN-000 - 02 / 12 / 2015 3 - 7

back to the table of contents

SAFETY AND PRECAUTIONS

Read all information, the datasheet, mounting instructions and wiring scheme
before working with the product. For personal and equipment safety, and for
optimum product performance, make sure you entirely understand the contents
before installing, using, or maintaining this product.

For safety and licensing (CE) reasons, unauthorised conversion and/ or modifications
to the product are not permitted.

e product must not be exposed to abnormal conditions, such as: extreme
temperatures, direc t sunlight or vibra tions. Chemical vapour s with high concentration
in combination with long exposure times can affect the product performance. Make
sure the work environment is as dry as possible; check for condensation spots.

All installations shall comply with the local health and safety regulations and local
electrical codes. is product can only be installed by an engineer or a technician
who has an exper t knowledge of the product and safety precautions.

Avoid contacts with energised electrical parts; always treat the product as if it
is life. Always disconnect the power source before connecting the power cables,
servicing or repairing the product.

Always verify that you apply appropriate power supply to the product and use wires
with appropriate size and characteristics. Make sure that all the screws and nuts are
well tightened and fuses (if any) are fitted well.

Recycling of equipment and packaging should be taken into consideration and
disposed in accordance with local and national legislation/regulations.

In case there are any questions that are not answered, please contact your technical
support or consult a professional.

MT

ELECTRONIC FAN SPEED
CONTROLLER

www.sentera.eu

MIW-MTX-EN-000 - 02 / 12 / 2015 4 - 7

back to the table of contents

PRODUCT DESCRIPTION

e MT speed controller provides manual control of the rotational speed of voltage
controllable (230 VAC, 50 Hz) motors by varying the supply voltage through phase
angle control. Several motors can be connected as long as the current limit is not
exceeded.

ARTICLE CODES

OUTPUT REGULATION FROM MINIMUM TO MAXIMUM

Code Current range, [A] Fuse, [A] (5*20 mm)

MTY-0-05-AT 0,05—0,5 F-0,63 A-H

MTY-0-15-AT 0,1—1, 5 F-2,00 A-H

MTY-0-25-AT 0,2—2,5 F-3 ,15 A -H

MTY-0-40-AT 0,4—4,0 F-5,00 A-H

OUTPUT REGULATION FROM MAXIMUM TO MINIMUM

Code Current range, [A] Fuse, [A] (5*20 mm)

MTX-0-05-AT 0,05—0,5 F-0,63 A-H

MTX-0-15-AT 0,1—1,5 F-2,00 A-H

MTX-0-25-AT 0,2—2,5 F -3,15 A- H

MTX-0-40-AT 0,4—4,0 F-5,00 A-H

INTENDED AREA OF USE

■

Manual control of the motor / fan speed in HVAC applications

■

For indoor use only

TECHNICAL DATA

■

Power supply: 230 VAC ± 10 % / 50 Hz

■

Unregulated input / output: 230 VAC / max. 2 A

■

Regulated output to motor(s)

■

Minimum speed adjustment by trimmer: 80—180 VAC

■

Speed control:

►

MTX – from maximum to minimum

►

MTY – from minimum to maximum

■

Enclosure:

►

External: ASA, white-ivory (RAL9010), IP54 (according to EN 60529)

►

Internal: polyamide, white-ivory (RAL9010), IP44 (according to EN 60529)

■

Operating ambient conditions:

►

temperature: 0—35 °C

►

rel. humidity: < 100 % rH (non-condensing)

■

Storage temperature: -10—40 °C

STANDARDS

■

Low Voltage Directive 2006/95/EC

■

EMC Directive 2004/108/EC: E N 6132 6

■

WEEE D i r e c tive 2012/19/ EU

■

RoHs Directive 2011/65/EU

MT

ELECTRONIC FAN SPEED
CONTROLLER

www.sentera.eu

MIW-MTX-EN-000 - 02 / 12 / 2015 5 - 7

back to the table of contents

OPERATIONAL DIAGRAMS

MTY-0-XX-AT MTX-0-XX-AT

Vout, [VAC]

Position

Maximum

speed

0

OFF Switch ON

External potentiometer value

Minimum

speed

Vout, [VAC]

Position

Maximum

speed

0

OFF Switch ON

External potentiometer value

Minimum

speed

WIRING AND CONNECTIONS



Power supply (230 VAC ± 10 % / 50 Hz)



Unregulated output (230 VAC / max. 2 A) for connecting a lamp,
valve … or three-wire motor connection; branched off after the
switch / input: to bypass switch

N Neutral

Regulated output to motor

Connections Cable cross section: max. 2,5 mm

2

MOUNTING INSTRUCTIONS IN STEPS

Before you start mounting the MT speed controller, read carefully “Safety and
Precautions”. Then proceed with the following mounting steps:

I. For inset mounting

1. Disconnect the mains supply.

2. Remove the knob by turning it to the right, beyond the stop end and then pull.

Open the cover and unscrew the loose nut.

3. Do the wiring according to the wiring diagram (see Fig. 1) using the information

from section “Wiring and connections”.

Fig. 1 Wiring and connections

230 VAC

230 VAC

M

1 2 3

Minimum

speed

adjustment

trimmer

Fuse hol der wi th a spa re fus e

MT

ELECTRONIC FAN SPEED
CONTROLLER

www.sentera.eu

MIW-MTX-EN-000 - 02 / 12 / 2015 6 - 7

back to the table of contents

4. Mount the internal enclosure to the wall according to the mounting dimensions

shown in Fig. 2.

Fig. 2 Mounting dimensions - inset mounting

82

89

26 33

50x50

7

5. Turn on the mains voltage and controller.

6. Adjust the minimal speed and turn off the controller.

7. Mount the cover with the nut.

8. Push the knob in place at off position

II. For surface mounting

1. Disconnect the mains supply.

2. Mount the external enclosure to the wall by dowels and screws (notdelivered).

Consider the mounting dimensions shown in Fig. 3.

Fig. 3 Mounting dimensions - surface mounting

62

62

7

3. Remove the knob by turning it to the right, beyond the stop end and then pull.

Open the cover and unscrew the loose nut.

4. Do the wiring according to the wiring diagram (see Fig. 1) using the information

from section “Wiring and connections”.

5. Mount the internal enclosure into the external enclosure by means of the

delivered screws and washers.

6. Turn on the mains voltage and controller.

7. Adjust the minimal speed and turn off the controller.

8. Mount the cover with the nut.

9. Push the knob in place at off position.

NOTE

You can drill a hole (5 mm) at the bottom of the external enclosure to take away
condensed water.

MT

ELECTRONIC FAN SPEED
CONTROLLER

www.sentera.eu

MIW-MTX-EN-000 - 02 / 12 / 2015 7 - 7

back to the table of contents

OPERATING INSTRUCTIONS

e controller is to be used only with voltage controllable fans / motors. You can
connec t several motors to the controller as long as the current limit is not exceeded.

e motor used should be protected internally against overheating.
e trimmer is adjusted so that the motor does not stop due to mains voltage

variations. e controller restarts after power failure.

In case of faulty operation

Please check if:

■

the right voltage is applied.

■

all connections are correct.

■

the machine to be regulated is functioning.

■

the fuse of the controller is OK.

In case that the fuse has blown up, remove the knob by turning it to the right, beyond
the end stop and then pull. Open the cover and unscrew the nut. Remove the fuse
holder with the help of a screwdriver. Replace the fuse. Mount all the parts back in
place.

ATTENTION

Use only fuses with type and rating specified above; otherwise, loss of warranty
will ensue.

TRANSPORT AND STOCK KEEPING INFORMATION

Avoid shocks and extreme conditions; stock in original packing.

WARRANTY INFORMATION AND RESTRICTIONS

Two years fr om the delive ry date against defec ts in manufacturing. Any modifica tions
or alterations to the product after the date of publication relieve the manufacturer
of any responsibilities. e manufacturer bears no responsibility for any misprints or
mistakes in this data.

MAINTENANCE

In normal conditions this product is maintenance-free. If soiled, clean with a dry or
dampish cloth. In case of heavy pollution, clean with a non-aggressive product. In
these circumstances the unit should be disconnected from the supply. Pay attention
that no fluids enter the unit. Only reconnect it to the supply when it is completelydry.

MT

ELECTRONIC FAN SPEED
CONTROLLER