SenTech STC-C42A, STC-C43A Product Specification

Small Cubic Type
CCIR High-Resolutions

Monochrome Analog Camera

STC-C42A (1/2” CCD)
STC-C43A (1/3” CCD)

Product Specification

!

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:
TO REDUCE THE RISK OF EL ECTRIC SHOC K, DO N OT

REMOVE COVER (OR B ACK). NO USER SERVICEABLE
PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Warning:
This equipment generates and uses radio frequency energy and if

not installed and used properly, I.e., in strict accordance with the
instruction manual, may cause harmful interference to radio
communications. It has been tested and found to comply with the
limits for a Class A computing device pursuant to Subpart J of Part
15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial
environment.

For U.S.A.

!

The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the use r to the
presence of uninsulated “dangerous
vo ltage ” wi thin the pr o duct ’ s
enclosure that may be of suffici ent
ma gnitude to constitute a risk of
electric shock to persons.

The exclamation point wit hin an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
i n st ru c ti o ns in t he l i te r at ur e
accompanying the appliance.

Warning:
This equipment generates and uses radio frequency energy and if

not installed and used properly, I.e., in strict accordance with the
instruction manual, may cause harmful interference to radio
communications. It has been tested and found to comply with the
limits for a Class A computing device pursuant to Subpart J of Part
15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial
environment.

For U.S.A.

Warning:
This digital apparatus does not exceed the Class A limits for radio

noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of
Communications.

For Canada

WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

Warning:
This equipment generates and uses radio frequency energy and if

not installed and used properly, I.e., in strict accordance with the
instruction manual, may cause harmful interference to radio
communications. It has been tested and found to comply with the
limits for a Class A computing device pursuant to Subpart J of Part
15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial
environment.

For U.S.A.

Warning:
This digital apparatus does not exceed the Class A limits for radio

noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of
Communications.

For Canada

WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

 Handle the camera with care. Do not abuse the camera. Avoid striking or shaking it. Improper handling

or storage could damage the camera.

 Do not pull or damage the camera cable.
 During camera use, do not wrap he unit in any material. This will cause the internal temperature of the

unit to increase.

 Do not expose the camera to moisture, or do not try to operate it in wet areas.
 Do not operate the camera beyond its temperature, humidity and power source ratings.
 While the camera is not being used, keep the lens or lens cap on the camera to prevent dust or

contamination from getting in the CCD or filter area and scratching or damaging this area.

 Do not keep the camera under the following conditions:

 In wet, moist, and high humidity areas
 Under hot direct sunlight

 Use a soft cloth to clean the camera. Use pressured air spray to clean the surface of the glass. DO not

scratch the surface of the glass.



 In high temperature areas
 Near an object that releases a strong magnetic or electric field
 Areas with strong vibrations

STC-C42A (1/2” CCD)

STC-C43A (1/3” CCD)

Safety Precautions

Product Precautions

STC-C42A (1/2” CCD)

1
2-4
2
3
4
4

5
6
7

C. Dimensions (Camera with Tripod)…………………………………………………………………….

B. Dimensions (Tripod)……………………………………………………………………………………………

I. Specifications

A. Electronic Specs / Mechanical Specs / Environmental Conditions…………….

II. Dimensions

A. Dimensions……………………………………………………………………………………………………………..

B. Rear Panel Specifications…………………………………………………………………………………

1. Connector Pin Assignment……………………………………………………………………..

2. DIP Switch Settings…………………………………………………………………………………….

3. External Sync………………………………………………………………………………………………..

4. Gain Mode Setting……………………………………………………………………………………….

Specification Manual i Rev 1.1

STC-C43A (1/3” CCD)

Contents

STC-C42A (1/2” CCD)

Specification Manual 1 of 7 Rev 1.1

I. Specifications

A. Electronic Specifications / Mechanical Specifications / Environmental Conditions

STC-C43A (1/3” CCD)

B. Rear Panel Specifications

12 Pin Connector

DIP Switch

External Sync (HD/VD) Signal
Impedance Switch

Gain Mode Switch

Manual Gain Pot

Figure 1

Figure 2

Specification Manual 2 of 7 Rev 1.1

Pin Assignment

*Note: Pin No.12 can be connected to GND

No. Internal sync External sysnc

1 GND GND

2 +12V DC +12V DC

3 VIDEO GND VIDEO GND

4 VIDEO OUT VIDEO OUT

5 HD GND HD GND

6 HD OUT HD IN

7 VD OUT VD IN

8 GND GND

9 TXD TXD

10 - -

11 - -

12 RXD (Note) RXD (Note)

Signal types

1. Connector Pin Assignment

12 Pin Connector Assignment
The connector type: HR10A-10R-12PB (Hirose) or equivalent

The camera settings can change by RS232C communication with No. 9 and 12.
Please refer the detail for the user’s guide.

STC-C42A (1/2” CCD)

STC-C43A (1/3” CCD)

STC-C42A (1/2” CCD)

1
2
3
4
5
6
7
8
9
0

O
N

Figure 3

Specification Manual 3 of 7 Rev 1.1

STC-C43A (1/3” CCD)

2. DIP Switch Settings (Refer to Dip Switch in Figure 1)
DIP Switch No. 1 to 4: Shutter Speed

DIP Switch No. 5 to 7 : No Function

DIP Switch No. 8: Gamma

DIP Switch No.9: Sync. System

DIP Switch No.10: Integration

STC-C42A (1/2” CCD)

Specification Manual 4 of 7 Rev 1.1

3. External Sync. (HD/VD) signal impedance setting (See External Sync. in Figure 1)

ON: 75Ohm termination
OFF: High impedance

4. Gain Mode Setting (See Gain Mode Switch in Fig. 1)

FIX: Fixed gain
MAN: Manual gain

The gain can be adjustable by the manual gain pot (See Manual Gain Pot in Fig. 1).

STC-C43A (1/3” CCD)

Specification Manual 5 of 7 Rev 1.1

II. Dimensions

A. Camera Dimensions

STC-C42A (1/2” CCD)

STC-C43A (1/3” CCD)

Unit: mm

Specification Manual 6 of 7 Rev 1.1

Tripod screw depth 5.5

2-M4 (P=0.7) depth 5.5

33.5

22(9)

24

12

4

9.5 9.5

(10.5)

(R13.8)

6.5

(10.5)

B. Tripod Dimensions

STC-C42A (1/2” CCD)

STC-C43A (1/3” CCD)

Unit: mm

C. Camera with Tripod Dimensions

Specification Manual 7 of 7 Rev 1.1

STC-C42A (1/2” CCD)

STC-C43A (1/3” CCD)

Unit: mm

STC-C42A (1/2” CCD)

Revision

Date (D/M/Y)

Changes

Name

Changes

1.0

26/10/2006

New Document

Sam Aimono

1.1

12/05/2008

Edited English

Michelle Campbell

Specification Manual Rev 1.1

Revisions

STC-C43A (1/3” CCD)

STC-C42A (1/2” CCD)

STC-C43A (1/3” CCD)

Sensor Technologies America, Inc.

1345 Valwood Pkwy, Suite 320
Carrollton, Texas 75006-6891
TEL [phone] FAX [phone]
URL http://www.sentechamerica.com/

Sensor Technology Co., Ltd.

7F, Harada Center Building
9-17, Naka cho 4chrome
Atsugi-city, Kanagawa
243-0018 Japan
TEL [phone] FAX [phone]
URL http://www.sentech.co.jp/

Taiwan Sensor Technology, Inc.

3F-6, No. 9, Aiguo W, Rd,. Jhong Jheng District
Taipei City 100, Taiwan, R.O.C.
TEL [phone] FAX [phone]
EMAIL: [e-mail]