Page 1
Small Cubic Type
VGA CCD
Monochrome Analog Camera
STC-A33A
User Guide
Page 2
!
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUC E THE RISK OF EL ECTRIC SHOCK, DO NOT
REMOVE C OVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Warning:
This equipment generates and uses radio frequency energy and if
not installed and used properly, I.e., in strict accordance with the
instruction manual, may cause harmful interference to radio
communications. It has been tested and found to comply with the
limits for a Class A computing device pursuant to Subpart J of Part
15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial
environment.
For U.S.A.
!
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is i ntended to alert the user t o the
presence of uninsulated “dangerous
vo ltage” wi th in the product ’ s
enclosure that may be of sufficient
ma gnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
i n st r ucti ons in th e l i te rat u re
accompanying the appliance.
Warning:
This equipment generates and uses radio frequency energy and if
not installed and used properly, I.e., in strict accordance with the
instruction manual, may cause harmful interference to radio
communications. It has been tested and found to comply with the
limits for a Class A computing device pursuant to Subpart J of Part
15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial
environment.
For U.S.A.
Warning:
This digital apparatus does not exceed the Class A limits for radio
noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of
Communications.
For Canada
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
Warning:
This equipment generates and uses radio frequency energy and if
not installed and used properly, I.e., in strict accordance with the
instruction manual, may cause harmful interference to radio
communications. It has been tested and found to comply with the
limits for a Class A computing device pursuant to Subpart J of Part
15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial
environment.
For U.S.A.
Warning:
This digital apparatus does not exceed the Class A limits for radio
noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of
Communications.
For Canada
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
Handle the camera with care. Do not abuse the camera. Avoid striking or shaking it. Improper handling
or storage could damage the camera.
Do not pull or damage the camera cable.
During camera use, do not wrap he unit in any material. This will cause the internal temperature of the
unit to increase.
Do not expose the camera to moisture, or do not try to operate it in wet areas.
Do not operate the camera beyond its temperature, humidity and power source ratings.
While the camera is not being used, keep the lens or lens cap on the camera to prevent dust or
contamination from getting in the CCD or filter area and scratching or damaging this area.
Do not keep the camera under the following conditions:
In wet, moist, and high humidity areas
Use a soft cloth to clean the camera. Use pressured air spray to clean the surface of the glass. Do NOT
scratch the surface of the glass.
User Guide 2 Rev 1.0
Under hot direct sunlight
In high temperature areas
Near an object that releases a strong magnetic or electric field
Areas with strong vibrations
STC-A33A
Safety Precautions
Product Precautions
Page 3
STC-A33A
Copyright & Disclaimer
Sensor Technologies America, Inc. (DBA Sentech America) believes the contents and specifications of its website, catalog,
documentation and ads are correct; however, Sentech America provides no representation or warranty regarding such information or
product (s) contained therein. It is requested that Sentech America be given appropriate acknowledgement in any subsequent use of
such work by a third party.
While every effort has been made to ensure that the details contained in Sentech America’s website and all documentation are correct
and up-to-date, Sentech America assumes no liability, legal or otherwise for any errors in listings, specifications, part numbers,
process, software or model applications. Sentech America reserves the right to change specifications, product descriptions, product
quality, pricing and application at any time without prior written or oral notice. Any party using such information assumes all risk for
any and all damaged caused to themselves, a third party and/or property by virtue of incorrect information and/or failure of these
products. By installing and/or using a Sentech America software development kit or other similar product and/or information obtained
from Sentech America’s website, catalog, documentation or ads, you hereby accept and understand these stated terms and conditions.
User Guide 3 Rev 1.0
Page 4
STC-A33A
Contents
I. Rear Panel Specifications ..................................................................................................................................................................................... 6
A. 12pin Connector ...................................................................................................................................................................................................... 6
B. DIP Switch Settings .................................................................................................................................................................................................. 7
C. External Sync (HD/VD) Signal Impedance Switch ..................................................................................................................................................... 7
D. Gain Switch .............................................................................................................................................................................................................. 7
II. Input / Output Signal Specifications ................................................................................................................................................................ 8-9
A. Input Signal Specifications ....................................................................................................................................................................................... 8
1. External Sync Signal ............................................................................................................................................................................................ 8
2. Trigger Signal ...................................................................................................................................................................................................... 8
B. Output Signal Specifications .................................................................................................................................................................................... 9
1. WEN (Write Enable) Signal .................................................................................................................................................................................. 9
2. HD/VD signals ..................................................................................................................................................................................................... 9
III. Camera Output Timing Charts .................................................................................................................................................................... 10-16
A. Normal Mode (Setting: address: 10H, value: 1XX0XXXX) ...................................................................................................................................... 10
1. Horizontal Timing .............................................................................................................................................................................................. 10
2. Vertical Timing ............................................................................................................................................................................................. 11-13
a. Normal Full Scanning ................................................................................................................................................................................ 11
b. Partial Full Scanning .................................................................................................................................................................................. 11
c. ½ Partial Scanning ..................................................................................................................................................................................... 12
d. ¼ Partial Scanning ..................................................................................................................................................................................... 12
e. Variable Partial Scanning .......................................................................................................................................................................... 13
B. Binning Mode (Setting: address: 10H, value: 1XX1XXXX) ................................................................................................................................. 14-16
1. Horizontal Timing .............................................................................................................................................................................................. 14
2. Vertical Timing ............................................................................................................................................................................................. 15-16
a. Binning Full Scanning ................................................................................................................................................................................ 15
b. Binning Partial Full Scanning ..................................................................................................................................................................... 15
c. Binning ½ Partial Scanning ........................................................................................................................................................................ 16
d. Binning ¼ Partial Scanning ........................................................................................................................................................................ 16
IV. Camera Function Mode .............................................................................................................................................................................. 17-24
A. Normal Mode ........................................................................................................................................................................................................ 17
1. Normal Mode (Frame Exposure) ....................................................................................................................................................................... 17
2. Normal Mode (Electronic Shutter) .................................................................................................................................................................... 17
B. Pulse Width Trigger Mode ................................................................................................................................................................................ 18-20
1. Pulse Width Trigger Mode (V-Reset)................................................................................................................................................................. 18
2. Pulse Width Trigger Mode (Non-Reset, External Sync) ..................................................................................................................................... 19
3. Pulse Width Trigger Mode (Non-Reset, Internal Sync) ..................................................................................................................................... 20
4. Pulse Width Trigger Mode (Exposure Timing) .................................................................................................................................................. 20
C. Edge Preset Trigger Mode................................................................................................................................................................................. 21-23
1. Edge Preset Trigger Mode (V-Reset) ................................................................................................................................................................. 21
2. Edge Preset Trigger Mode (Non-Reset, External Sync) ..................................................................................................................................... 22
3. Edge Preset Trigger Mode (Non-Reset, Internal Sync) ...................................................................................................................................... 23
4. Edge Preset Trigger Mode (Exposure Timing) ................................................................................................................................................... 23
D. H Reset Mode ........................................................................................................................................................................................................ 24
User Guide 4 Rev 1.0
Page 5
STC-A33A
V. Communication Protocol Specifications ...................................................................................................................................................... 25-66
A. Communication Method........................................................................................................................................................................................ 25
B. Communication Settings ........................................................................................................................................................................................ 25
C. The Communication Format .................................................................................................................................................................................. 26
D. The Camera Control Command ........................................................................................................................................................................ 27-66
1. The Camera Command List .......................................................................................................................................................................... 27-28
2. Descriptions of the Camera Control Commands .......................................................................................................................................... 29-33
3. Camera Control Commands ......................................................................................................................................................................... 34-66
a. Normal Mode (90fps) ................................................................................................................................................................................ 34
b. Normal Mode (60fps)................................................................................................................................................................................ 35
c. Normal Mode (30fps) ................................................................................................................................................................................ 36
d. Trigger Mode (90fps, Full scanning) .......................................................................................................................................................... 37
e. Trigger Mode (90fps, Partial full scanning) ............................................................................................................................................... 38
f. Trigger Mode (90fps, ½ partial scanning) .................................................................................................................................................. 39
g. Trigger Mode (90fps, ¼ partial scanning) .................................................................................................................................................. 40
h. Trigger Mode (90fps, Variable partial scanning) ....................................................................................................................................... 41
i. Trigger Mode (90fps, Binning full scanning) .............................................................................................................................................. 42
j. Trigger Mode (90fps, Binning partial full scanning) ................................................................................................................................... 43
k. Trigger Mode (90fps, Binning ½ partial scanning) ..................................................................................................................................... 44
l. Trigger Mode (90fps, Binning ¼ partial scanning) ...................................................................................................................................... 45
m. Trigger Mode (90fps, Binning variable partial scanning) ......................................................................................................................... 46
n. Trigger Mode (60fps, Full scanning) .......................................................................................................................................................... 47
o. Trigger Mode (60fps, Partial full scanning) ............................................................................................................................................... 48
p. Trigger Mode (60fps, ½ partial scanning) ................................................................................................................................................. 49
q. Trigger Mode (60fps, ¼ partial scanning) .................................................................................................................................................. 50
r. Trigger Mode (60fps, Variable partial scanning) ........................................................................................................................................ 51
s. Trigger Mode (60fps, Binning full scanning) .............................................................................................................................................. 52
t. Trigger Mode (60fps, Binning partial full scanning) ................................................................................................................................... 53
u. Trigger Mode (60fps, Binning ½ partial scanning)..................................................................................................................................... 54
v. Trigger Mode (60fps, Binning ¼ partial scanning) ..................................................................................................................................... 55
w. Trigger Mode (60fps, Binning variable partial scanning) .......................................................................................................................... 56
x. Trigger Mode (30fps, Full scanning) .......................................................................................................................................................... 57
y. Trigger Mode (30fps, Partial full scanning) ............................................................................................................................................... 58
z. Trigger Mode (30fps, ½ partial scanning) .................................................................................................................................................. 59
aa. Trigger Mode (30fps, ¼ partial scanning) ................................................................................................................................................ 60
bb. Trigger Mode (30fps, Variable partial scanning) ..................................................................................................................................... 61
cc. Trigger Mode (30fps, Binning full scanning) ............................................................................................................................................ 62
dd. Trigger Mode (30fps, Binning partial full scanning) ................................................................................................................................ 63
ee. Trigger Mode (30fps, ½ partial scanning) ................................................................................................................................................ 64
ff. Trigger Mode (30fps, Binning ¼ partial scanning) .................................................................................................................................... 65
gg. Trigger Mode (30fps, Binning variable partial scanning) ......................................................................................................................... 66
User Guide 5 Rev 1.0
Page 6
No.
Signal Types
Internal Sync
External Sync
1
GND
GND
2
+12V DC
+12V DC
3
VIDEO GND
VIDEO GND
4
VIDEO OUT
VIDEO OUT
5
HD GND
HD GND
6
HD OUT
HD IN
7
VD OUT
VD IN
8
GND
GND
9
TXD
TXD
10
WEN OUT
WEN OUT
11
TRG IN
TRG IN
12
RXD (Note)
RXD (Note)
A. 12 Pin Connector
B. DIP Switch
E. Manual Gain Pot
D. Gain Switch
C. External Sync (HD / VD) Signal Impedance Switch
Note: Pin No.12 can be connected to GND
STC-A33A
I. Rear Panel Specifications
A. 12 Pin Connector
The connector type: HR10A – 10R – 12PB (Hirose) or equivalent
The camera settings can change by RS232C communication with No. 9 and 12. Please further refer to the details provided in
the user’s guide.
User Guide 6 Rev 1.0
Page 7
DIP Switch Settings
No. 1 to 3: Shutter Speed
Shutter Speed
No.1
No.2
No.3
OFF / Pulse Width Trigger
OFF
OFF
OFF
1/200 seconds
ON
OFF
OFF
1/500 seconds
OFF
ON
OFF
1/1,000 seconds
ON
ON
OFF
1/2,000 seconds
OFF
OFF
ON
1/4,000 seconds
ON
OFF
ON 1/8,000 seconds
OFF
ON
ON 1/20,000 seconds
ON
ON
ON
No. 4 to 5: Reset Mode
Reset Mode
No. 4
No. 5
Non-reset
OFF
OFF
V-reset
ON
OFF
No. 6: Trigger Polarity
Trigger Polarity
No. 6
Positive (Rising Edge)
OFF
Negative (Falling Edge)
ON
No. 7 to 8: Scanning Mode
Scanning Mode
No. 7
No. 8
Full Scanning
OFF
OFF
Full Scanning
ON
OFF
1/2 Partial Scanning
OFF
ON
1/4 Partial Scanning
ON
ON
Note: Please use the communication setting when the
system needs “Partial Full Scanning” or “Variable Partial
Scanning”
No. 9: Sync. System
Sync. System
No. 9
External Sync.
OFF
Internal Sync.
ON
No. 0: Binning Mode
Binning Mode
No. 10
OFF
OFF
ON
ON
External Sync Signal Impedance
75 Ω termination
ON
High impedance
OFF
Gain Mode
Fixed Gain
FIX
Manual Gain
MANU
1
2
3
4
5
6
7
8
9
0
O
N
STC-A33A
B. DIP Switch Settings
C. External Sync (HD / VD) Signal Impedance Switch
D. Gain Switch
User Guide 7 Rev 1.0
Note 1: The gain can be adjusted by the communication when the fixed gain is selected
Note 2: The gain can be adjusted by the pot (E) on the rear panel when the manual gain is selected.
Page 8
2-5Vp-p
HD
VD
4～5V
0～0.5V
II. Input / Output Signal Specifications
A. Input Signal Specifications
1. External Sync Signals
a. Signal Level: 2.0 to 5.0 Vp-p
b. Termination Impedance: 75 / 10k Ω (Switch Selectable)
c. Signal Polarity: Negative
d. External HD / VD signal input phase tolerance: +/- 8.0 µseconds at 30fps
+/- 4.0 µseconds at 60fps
+/- 2.6 µseconds at 90fps
e. Pulse Width: HD: 3.20 +/- 1 µseconds (Low Level)
VD: 4 to 13H (Low Level)
f. Frequency Tolerance of HD Signal: 15. 734 kHz +/- 1% at 30 fps
31.468 kHz +/- 1% at 60 fps
47.674 kHz +/- 1% at 90 fps
2. Trigger Signal
a. Signal Level: Low Level: 0 to 0.5 Vp-p
High Level: 4.0 to 5.0 Vp-p
b. Termination Impedance: 10k Ω
c. Signal Polarity: Rising edge (Positive) / Falling edge (Negative)
(Switch Selectable)
User Guide 8 Rev 1.0
d. Pulse Width: 2 µseconds to 250 mseconds
STC-A33A
Page 9
STC-A33A
B. Output Signals Specifications
1. WEN (Write Enable) Signal
a. Signal Level: 3.3 Vp-p at 10k Ω termination
b. Signal Polarity: Negative
c. Pulse Width: 1H (H: Horizontal)
2. HD / VD Signals
a. Signal Level: 3.3 Vp-p at 10k Ω termination
b. Signal Polarity: Negative
c. Pulse Width: HD: 78clock (clock: pixel clock)
VD: 9H
User Guide 9 Rev 1.0
Page 10
18CLK
132CLK
Video out
60CLK 54CLK 648CLK
780CLK
Horizontal blanking
Video output
One horizontal (1H)
OB
H-trans. Holt
DM
OB
648CLK231
659CLK
OB
72CLK 16 31
78CLK
CCD out
74 4
1CLK
HD
Effective pixels
III. Camera Output Timing Charts
A. Normal Mode (Setting: Address: 10H, Value: 1XX0XXXX)
1. Horizontal Timing
User Guide 10 Rev 1.0
1 CLK = 81.4817 nseconds at 30 fps
1 CLK = 40.7407 nseconds at 60 fps
1 CLK = 27.1606 nseconds at 90 fps
STC-A33A
Page 11
31H
OB
DM
9H
494H7H
31H
Video out
CCD out
VD
Vertical
blanking
Effective pixels
525H
One vertical (1V)
516H9H
8
494H
1H
Video output
WEN out
493
494
1
2
5
OB
92
9H
494H11H
WEN out
Video out
VD
Vertical
blanking
505H
One vertical (1V)
496H9H
11H
1H
Video output
493
494
1
2
2. Vertical Timing
a. Normal Full Scanning (Settings: Address: 10H, Value: 1XX00XXX; Address: 11H, Value: X000X000)
b. Partial Full Scanning (Settings: Address: 10H, Value: 1XX01XXX; Address: 11H, Value: X000X000)
User Guide 11 Rev 1.0
STC-A33A
1 H = 63.5556 µseconds, 29.9700 Hz
1 H = 31.7778 µseconds, 59.9400 Hz
1 H = 21.1852 µseconds, 89.9100 Hz
1 H = 63.5556 µseconds, 31.1569 Hz
1 H = 31.7778 µseconds, 62.3138 Hz
1 H = 21.1852 µseconds, 93.4708 Hz
Page 12
19H
9H
19H
Video out
VD
(V-reset)
Vertical
blanking
262H
One vertical (1V)
253H9H
243H
1H
Video output
WEN out
376
378
135
136
VD
(Non-reset)
525H
One vertical (1V)
516H
9H
27H
9H
27H
Video out
VD
(V-reset)
Vertical
blanking
131H
One vertical (1V)
122H9H
104H
1H
Video output
WEN out
303
304
201
202
VD
(Non-reset)
525H
One vertical (1V)
516H9H
c. 1/2 Partial Scanning (Settings: Address: 10H, Value: 1XX01XXX; Address: 11H, Value: X000X001)
d. 1/4 Partial Scanning (Settings: Address: 10H, Value: 1XX01XXX; Address: 11H, Value: X000X010)
User Guide 12 Rev 1.0
1 H = 63.5556 µseconds, 60.0544 Hz
1 H = 31.7778 µseconds, 120.108 Hz
1 H = 21.1852 µseconds, 180.163 Hz
1 H = 63.5556 µseconds, 120.108 Hz
1 H = 31.7778 µseconds, 240.217 Hz
1 H = 21.1852 µseconds, 360.326 Hz
STC-A33A
Page 13
VD
(V-reset)
Effective pixels
1 V
One vertical (1V)
BLK_F + V_ACT + BLK_B
9H
Start line
VD
(Non-reset)
1V
One vertical (1V)
1068H
9H
Video out
(Non-reset)
Vertical blanking
BLK_BBLK_F V_ACT
Video output Vertical blanking
9H
Video out
(V-reset)
Vertical blanking
BLK_BBLK_F V_ACT
1H
Video output
WEN out
Vertical blanking
CCD effective
lines
Blanking
(Front)
Effective
lines
Optical black
+
Dummy bit
Blanking
(Back)
Optical black
e. Variable Partial Scanning (Settings: Address: 10H, Value: 1XX01XXX; Address; 11H, Value: X000X111)
User Guide 13 Rev 1.0
STC-A33A
Page 14
42CLK
430CLK
Video out
140CLK 248CLK 1360CLK
1790CLK
Horizontal blanking
Video output
One horizontal (1H)
OB
H-trans. Holt
DM
OB
1360CLK240
1392CLK
OB
336CLK 20 40
182CLK
CCD out
1616 16
1CLK
HD
Effective pixels
B. Binning Mode (Settings: Address: 10H, Value: 1XX1XXXX)
1. Horizontal Timing
User Guide 14 Rev 1.0
1 CLK = 81.4817 nseconds at 30 fps
1 CLK = 40.7407 nseconds at 60 fps
1 CLK = 27.1606 nseconds at 90 fps
STC-A33A
Page 15
20H
9H
242H20H
WEN out
Video out
VD
Vertical
blanking
262H
One vertical (1V)
253H9H
1H
Video output
481+482
483+484
1+2
3+4
21H
9H
247H21H
WEN out
Video out
VD
Vertical
blanking
268H
One vertical (1V)
253H9H
1H
Video output
491+492
493+494
1+2
3+4
2. Vertical Timing
a. Binning Full Scanning (Settings: 10H, Value: 1XX10XXX; Address: 11H, Value: X000X000)
b. Binning Partial Full Scanning (Settings: Address: 10H, Value: 1XX11XXX; Address: 11H, Value: X000X000)
User Guide 15 Rev 1.0
STC-A33A
1 H = 63.5556 µseconds, 60.0544 Hz
1 H = 31.7778 µseconds, 120.108 Hz
1 H = 21.1852 µseconds, 180.163 Hz
1 H = 63.5556 µseconds, 58.7099 Hz
1 H = 31.7778 µseconds, 117.419 Hz
1 H = 21.1852 µseconds, 176.129 Hz
Page 16
19H
9H
19H
Video out
VD
(V-reset)
Vertical
blanking
140H
One vertical (1V)
131H9H
121H
1H
Video output
WEN out
373+374
375+376
135+136
137+138
VD
(Non-reset)
525H
One vertical (1V)
516H9H
27H
9H
27H
Video out
VD
(V-reset)
Vertical
blanking
79H
One vertical (1V)
70H9H
52H
1H
Video output
WEN out
301+302
303+304
201+202
203+204
VD
(Non-reset)
525H
One vertical (1V)
516H9H
c. Binning 1/2 Partial Scanning (Settings: Address: 10H, Value: 1XX11XXX; Address: 11H, Value: X000X001)
d. Binning 1/4 Partial Scanning (Settings: Address: 10H, Value: 1XX11XXX; Address: 11H, Value: X000X010)
User Guide 16 Rev 1.0
STC-A33A
1 H = 63.5556 µseconds, 112.387 Hz
1 H = 31.7778 µseconds, 224.775 Hz
1 H = 21.1852 µseconds, 337.162 Hz
1 H = 63.5556 µseconds, 199.167 Hz
1 H = 31.7778 µseconds, 398.335 Hz
1 H = 21.1852 µseconds, 597.503 Hz
Page 17
E x p o s u r e t i m e
I n t e r n a l
VD
CCD
e x p o s u r e
V i d e o o u t
E x p o s u r e
t i m e
I n t e r n a l
VD
CCD
e x p o s u r e
V i d e o o u t
STC-A33A
IV. Camera Function Mode
A. Normal Mode
1. Normal Mode (Frame Exposure)
2. Normal Mode (Electronic Shutter)
User Guide 17 Rev 1.0
Page 18
Norm al mode
Exposure time
Max. 1H
Trigger mode Norm al mode
Not
e 1: Auto
m
atically
s
witches
t
o normal
mode if t
h
e pulse
width of th
e trigger
signal is
more
than 500
msec.
Function mode
Internal VD
CCD exposure
Trigger signal
(Positive)
Video out
Note 3
WEN signal out
Note 5
Note 4
Note 2
B. Pulse Width Trigger Mode
In the “Pulse Width Trigger Mode” with positive polarity, the camera exposure starts at the rising edge of the trigger signal and
stops at the falling edge of the trigger signal. Therefore, in the case that the exposure positive polarity is selected, the actual
exposure occurs when the trigger signal is at its high state.
1. Pulse Width Trigger Mode (V-Reset)
Note 1: The camera does NOT switch to normal mode when the long exposure mode is selected. The timing chart above
shows when the long exposure mode is selected.
Note 2: The internal VD signal is reset immediately after the exposure is finished as depicted above; the video
output signal is sent out according to that reset VD timing.
Note 3: The exposure time is controlled by the pulse width of the trigger signal.
Note 4: External VD signal input is continuous during the external sync mode and it is disregarded during the trigger
mode.
Note 5: The WEN signal does not output when the exposure by the trigger signal does not exist.
User Guide 18 Rev 1.0
STC-A33A
Page 19
Normal mode
Exposure time
1H
Trigger mode Normal mode
Note 1 : Automatically switches
to n ormal mode if the pulse
width of the trigger signal is
more than 500 msec.
Function mode
External VD
CCD exposure
Trigger signal
(Positive)
Video out
Note 3
WEN signal out
Note 4
Note 5
Note 2
2. Pulse Width Trigger Mode (Non-Reset, External Sync)
Note 1: The camera does NOT switch to the normal mode when the long exposure mode is selected. This timing chart
shows when the long exposure mode is selected.
Note 2: The internal VD signal is reset immediately after the exposure is finished. The video output signal is sent out
according to that reset VD timing.
Note 3: The exposure time is controlled by the pulse width of the trigger signal.
Note 4: External VD signal inputs continuously during the external sync mode. External VD signal is disregarded during
the trigger mode.
Note 5: The WEN signal does not output when the exposure by the trigger signal does not exist.
User Guide 19 Rev 1.0
STC-A33A
Page 20
Normal mode
Exoposure time
Trigger mode Normal mode
Automatically switches to
nor m al mode i f the pu lse width
of the trigger signal is more
than 500 msec.
Note. 1
Function mode
Internal VD
CCD exposure
Trigger signal
(Positive)
Video out
Note. 3
WEN signal out
Note. 5
Next
VD
Note. 2
Next
VD
Note. 4
T1'
SUB
SG
(127 CLK)
Trigger
singal
Exposure
time
Exposure time: T1' = T1 + 127 CLK
T1
30 CLK
Filtering (Note.1)
3. Pulse Width Trigger Mode (Non-Reset, Internal Sync)
Note 1: The camera does NOT switch to the normal mode when the long exposure mode is selected. This timing chart
shows when the long exposure mode is selected.
Note 2: The internal VD signal does not reset by the trigger signal. The video output signal is sent out at the next VD
timing.
Note 3: The exposure time is controlled by the pulse width of the trigger signal.
Note 4: The external VD signal inputs continuously during the external sync mode.
Note 5: The WEN signal does not output when the exposure by the trigger signal does not exist.
4. Pulse Width Trigger Mode (Exposure Timing)
Note 1: The trigger signal that is less than or equal to 30 clocks is removed by the filtering system.
Note 2: The Input trigger signal has to be more than 31 clocks pulse width.
Note 3: The exposure starts 63 clocks after the rising edge of the trigger signal.
User Guide 20 Rev 1.0
STC-A33A
Page 21
Normal mode
Exposure time
Max. 1H
Trigger mode Normal mode
Automatically switch to the normal
mode if the pulse width of the
trigger signal is more than
500 mseconds
Note. 1
Function mode
Internal VD
CCD exposure
Trigger signal
(Rising edge)
Video out
Note. 2
Note. 3
WEN signal out
Note. 4
Note. 5
C. Edge Preset Trigger Mode
In this “Edge Preset Trigger Mode” with positive polarity, the camera exposure starts at the rising edge of the trigger signal. In
this mode, the exposure duration time is based on the preset exposure time (shutter speed) by the camera setting
communication or the DIP Switch on the rear panel.
1. Edge Preset Trigger Mode (V-Reset)
Note 1: The camera does NOT switch to the normal mode when the long exposure mode is selected. This timing chart shows
when the long exposure mode is selected.
Note 2: The internal VD signal is reset immediately after the exposure is finished; the video output signal is sent out according
to that reset VD timing.
Note 3: The exposure time is controlled by the camera setting communication (Refer to the command 20H and 21H) or the
DIP Switch on the rear panel as “shutter speed”.
Note 4: External VD signal inputs continuously during the external sync mode. External VD signal is disregarded during the
trigger mode.
Note 5: The WEN signal does not output when the exposure by the trigger signal does not exist.
User Guide 21 Rev 1.0
STC-A33A
Page 22
Normal mode
Exposure time
Max. 1H
Trigger mode Normal mode
Automatically switch to the normal
mode if the pulse width of the
trigger signal is more than
500 mseconds
Note. 1
Function mode
Internal VD
CCD exposure
Trigger mode
(Rising edge)
Video out
Note. 2
Note. 3
WEN signal out
Note. 4
Note. 5
2. Edge Preset Trigger Mode (Non-Reset, External Sync)
Note 1: The camera does NOT switch to normal mode when the long exposure mode is selected.
This timing chart shows when the long exposure mode is selected.
Note 2: The internal VD signal is reset immediately after the exposure is finished; the video output signal is sent out
according to the timing of the VD being reset.
Note 3: The exposure time is controlled by the camera setting communication (Refer to the command 20H and 21H) or
the DIP Switch on the rear panel as “shutter speed”.
Note 4: External VD signal inputs continuously during the external sync mode. The external VD signal is disregarded
during the trigger mode.
Note 5: The WEN signal does not output when the exposure by the trigger signal does not exist.
STC-A33A
User Guide 22 Rev 1.0
Page 23
Normal mode
Exposure time
Trigger mode Normal mode
Au toma tically swi tche s to th e
no rmal mod e i f th e pulse wid th
of the tr igge r si gna l is mor e
th an 500 mse c
Note. 1
Function mode
Internal VD
CCD exposure
Trigger signal
(Rising edge)
Video out
Note. 3
WEN signal out
Note. 4
Next
VD
Note. 2
Next
VD
Next
VD
Trigger
signal
Exposure
time
T1'
SUB
SG
Exposure time: T1' =
Preset exposure time for the electronic shutter
Filtering (Note.1)
30CLK
3. Edge Preset Trigger Mode (Non-Reset, Internal Sync)
Note 1: The camera does NOT switch to the normal mode when the long exposure mode is selected. This timing chart
shows when the long exposure mode selected.
Note 2: The internal VD signal does not reset by the trigger signal. The video output signal is sent out at the next internal
reset VD timing.
Note 3: The exposure time is controlled by the camera setting communication (Refer to the command 20H and 21H) or
the DIP Switch on the rear panel as “shutter speed”.
Note 4: External VD signal input continuously during the external sync mode. External VD signal is disregarded during
the trigger mode.
Note 5: The WEN signal does not output when the exposure by the trigger signal does not exists during the trigger mode.
4. Edge Preset Trigger Mode (Exposure Timing)
Notes:
The trigger signal equals to or shorter than 30 clocks is removed by the filtering system.
The input trigger signal has to be more than 31 clocks pulse width.
The exposure starts 63 clocks after the rising edge of the trigger signal.
User Guide 23 Rev 1.0
STC-A33A
Page 24
Next HD
Video out
SUB pulse
Internal HD
CCD exposure
Trigger signal
(Rising edge)
Noise
Normal SUB pulse timing
STC-A33A
D. H Reset Mode
Normally, the video noise appears when the start of the trigger signal is applied before finishing the video out of the previous
frame. This noise is caused by the SUB pulse, which is activated to clear all residual charges on the CCD prior to a new
exposure. By selecting “H reset mode”, the camera automatically holds the actual activation of the trigger until the next
horizontal blanking period. By doing this, the SUB pulse is activated during the horizontal blanking period and the noise in the
image can be avoided.
Note: Due to the principal of this operation, there can be a maximum 1H of delay of the actual trigger signal.
User Guide 24 Rev 1.0
Page 25
Settings
Baud Rate
9,600 bps / 38,400 bps
Data Bit
8 bit
Parity
None
Stop Bit
1 bit
Flow Control
None
STC-A33A
V. Communication Protocol Specifications
This camera has a communication function that enables external devices, such as the PC, to control the camera functions and
parameters. Use the “CLCtrl” communication software (version 9.0 or later) to communicate, or follow the communication protocol
described below to communicate with the camera.
Note: A communication problem may occur under the following conditions:
When the external sync frequency is out of the specification (more than 1% off from the specified normal frequency)
When external sync is unstable.
Approximately for one second after changing the sync mode.
Approximately for one second after switching the frame rate.
A. Communication Method
UART (RS232C)
B. Communication Settings
User Guide 25 Rev 1.0
Page 26
SOF
Device Code
Read / Write
Page Selection
Command Code
Data Length
Data
EOF
8 bit
(always 02H)
6 bit
1 bit
(always 00H)
1 bit
8 bit
8 bit
8 bit
8 bit
(always 03H)
SOF
Device Code
Read / Write
Page Selection
Command Code
Data Length
Data
EOF
8 bit
(always 02H)
6 bit
1 bit
(always 01H)
1 bit
8 bit
8 bit
Data
Length
Byte
8 bit
(always 03H)
SOF
Data Length
Data
EOF
8 bit (always 02H)
8 bit
Data Length Byte
8 bit (always 03H)
SOF
Data Length
Data
EOF
8 bit (always 02H)
8 bit (always 00H)
8 bit
8 bit (always 03H)
Name
Descriptions
SOF
Start of the frame. The set (or receive) value is always “02H”
Device Code
This indicates the destination of the communication
The device code for the camera is “000000”. Other codes are the peripheral devices.
Read / Write
This specifies “Read” or “Write” to command numbers. Set 0 for “Read” and 1 for “Write”.
Page Selection
This specifies page selection (access selection) to registers and EEPROM of command.
Set 0 to access the command register of the camera.
Read command: To read the current data from the command register.
Write command: To set the data into the command register. The data in the EEPROM is not replaced.
Set 1 to access the EEPROM of the camera
Read command: To read the data from the EEPROM
Write command: To save the data into the EEPROM as default data
Notes:
1. The camera operates with the data in the EEPROM when the camera is powered on.
2. The camera returns the receiving code “01H” to the PC after save the data into the EEPROM. The camera rejects any commands
during the data saved (approximately 5 mseconds / byte) and returns the receiving code “07H” (busy) to the PC.
Command Code
This indicates the command. Refer to the following page for the details.
Data Length
This indicates the data length (Unit is byte).
Sending data: Set to 0 when sending the read command. The data length is dependent on each write command when sending the write
command.
Receiving data: The data length is dependent on each write command after sending the read command.
Receive “00H” after sending the write command.
Receive “00H” when an error has occurred.
Data
This indicates write data or read data according to the command type.
EOF
End of the frame. The set (or receive) value is always “03H”
Receiving Code
This indicates result of the sending command:
01H: Receiving OK (ACK)
10H: Receiving problem (NAC)
07H: The camera is in process (Busy)
11H: Communication problem
STC-A33A
C. The Communication Format
1. Sending Data Format from the PC to the Camera is shown below:
a. Sending the read command:
b. Sending the write command:
2. Receiving data format from the camera is as below:
a. After sending the reading command:
b. After sending the write command:
3. Descriptions of the Format:
User Guide 26 Rev 1.0
Page 27
Command
No.
Read / Write
Save to
EEPROM
Function
Initial
Data
Data
Range
00H
Read
Product code (8bit: D[7…0])
17
-
01H
Read
Hardware version (8bit: D[7…0])
ROMdata
-
02H
Read
Firmware version (16bit: D[15…8])
D[15…12]: The integer, D[11…8]: 1
st
place of the decimal
ROMdata
03H
Read
Firmware version 16bit D[7…0])
D[7…4]: 2
nd
place of the decimal,
D[3…0]: 3
rd
place of the decimal
04H
Read / Write
X
Serial number (32bit: D[31…24])
D[31…28]: 0, D[27…24]: 7
th
figure
The factory
set value
-
05H
Read / Write
X
Serial number (32bit: D[23…16])
D[23…20]: 6
th
figure, D[19…16]: 5th figure
06H
Read / Write
X
Serial number (32bit: D[15…8])
D[15…12]: 4
th
figure, D[11…8]: 3rd figure
07H
Read / Write
X
Serial number (32bit: D[8…0])
D[7…4]: 2nd figure, D[3…0]: 1
st
figure
08H
Read / Write
X
Customer Code (8bit: D[7…0])
0
-
09 to 0CH
Read / Write
Reserved (Please do not use these)
-
-
0DH
Read / Write
X
The factory adjusted DAC reference voltage value (Back up Data)
(8bit: D[7…0])
The factory
adjusted value
0EH
Read / Write
X
The factory adjusted the digital gain value (Backup data) (8bit: D[7…0])
The factory
adjusted value
0 to 255
0FH
Read / Write
X
The factory adjusted gain offset value (Backup Data) (8bit: D[7…0])
The factory
adjusted value
0 to 63
10H
Read / Write
X
The camera function mode 1 (8bit: D[7…0])
1
11H
Read / Write
X
The camera function mode 2 (8bit: D[7…0])
0
12H
Read / Write
X
The camera function mode 3 (8bit: D[7…0])
0
13H
Read / Write
X
The camera function mode 4 (8bit: D[7…0])
0 14H
Read / Write
X
The communication mode (8bit: D[7…0])
0
15 to 1FH
Reserved (Please do not use these)
-
-
20H
Read / Write
X
The exposure time (H) of the electronic shutter (16bit: D[7…0])
0
0 to
4095
21H
Read / Write
X
The exposure time (H) of the electronic shutter (16bit: D[15…8])
22H
Read / Write
X
The exposure time (CLK) of the electronic shutter (16bit: D[7…0])
0
0 to 779
23H
Read / Write
X
The exposure time (CLK) of the electronic shutter (16bit: D[15…8])
24H
Read / Write
X
The start line of the variable partial scanning (16bit: D[7…0])
0
0 to 493
25H
Read / Write
X
The start line of the variable partial scanning (16bit: D[15…8])
26H
Read / Write
X
The effective lines of the variable partial scanning 916bit: D[7…0])
494
0 to 494
27H
Read / Write
X
The effective lines of the variable partial scanning (16bit: D[15…8])
28H
Read / Write
X
The delay time of the trigger (8bit: D[7…0])
0
0 to 31
29 to 2FH
Reserved (Please do not use these)
-
-
30H
Read / Write
X
CDS gain (8bit: D[7…0])
0
0 to 255
31H
Read / Write
X
The digital gain (8bit: D[7…0])
The value of
0EH address
-
STC-A33A
D. The Camera Control Command
1. The Camera Command List
Notes:
The data unit of each command is 1 byte (8bit).
The data can be saved to the EEPROM if there is “X” in the “Save to EEPROM” column in the below list.
The camera initializes based on the stored data in the EEPROM when the power is applied.
User Guide 27 Rev 1.0
Page 28
Command
No.
Read / Write
Save to
EEPROM
Function
Initial
Data
Data
Range
32H
Read / Write
X
The gain offset (6bit: D[5…0])
The value of
0FH address
-
33 to 37H
Reserved (Please do not use these)
- - 38H
Read / Write
X
The clamp level (8bit: D[7…0])
4
0 to 31
39 to 5FH
Reserved (Please do not use these)
-
-
60H
Read / Write
X
Control selection (Rear panel / communication) 98bit: D[7…0])
0
-
61H
Read / Write
X
DAC reference voltage (8bit: D[7…0])
The value of
0DH address
-
62H
Read / Write
X
Fixed gain value for the rear panel (8bit: D[7…0])
16
0 to 255
63 to 64H
Read / Write
X
Maximum setting of the pot on the rear panel (16bit: D[15…0])
422
0 to
65535
65 to 6FH
Reserved (Please to do not use these)
-
-
70 to 71H
Read
The current selection on the rear panel (1 bit: D[15])
-
-
72H
Read
The current gain value 98bit: D[7…0])
- - 73H
Reserved (Please do not use these)
-
-
74 to 75H
Read
Status of the DIP switch on the rear panel (10bit: D[9…0])
-
-
76 to 7DH
Reserved (Please do not use these)
-
-
7EH
Read / Write
X
Firmware version verification (16bit: D[15…8])
D[15…12]: The integer, D[11…8]: 1
st
place of the decimal
The value of
02H address
-
7FH
Read / Write
X
Firmware version verification (16bit: D[7…0])
D[7…4]: 2
nd
place of the decimal, D[3…0]: 3rd place of the decimal
The value of
03H address
-
80H
Read / Write
EEPROM control (8bit: D[7…0])
0
0 to 3
81 to FFH
Reserved (Please do not use these)
-
-
STC-A33A
User Guide 28 Rev 1.0
Page 29
Command No.
Command Descriptions
0DH:
DAV_BK[7…0]
[Back up data of the factory adjusted value for DAC reference voltage]
This data is the factory adjusted DAC reference voltage that is set to the address 61H.
0EH:
DGB_BK[7…0]
[Back up data of the factory adjusted value for the digital gain]
This data is the factory adjusted digital gain that is set to the address 31H.
0FH:
GOFS_BK[7…0]
[Back up data of the factory adjusted value for the gain offset]
This data is the factory adjusted gain offset that is set to the address 32H.
10H:
MOD1[7…0]
[The camera function mode1] Initial data: MOD1[7…0] = 1
This sets the below camera function modes.
D[7…0]
D7
D6
D5
D4
D3
D2
D1
D0 D7:
Long exposure mode
0:OFF
1: ON
D6:
Trigger polarity
0: Positive
1: Negative
D5:
Trigger mode
0: Edge preset
1:Pulse width
D4:
Binning mode
0: OFF (Normal)
1: ON (Binning)
D3:
Scanning method
0: Full scanning
1:Partial Scanning
D2 to D0:
Reset mode
000: Non-Reset
001: V-Reset
010 to 111: No function (Prohibited setting. Do not set these values)
11H:
MOD2[7…0]
[The camera function mode 2] Initial data: MOD2[7…0] = 0
This sets the below camera function modes.
D[7…0]
D7
D6
D5
D4
D3
D2
D1
D0
D7:
Sync system
0: HD/VD signal in (External)
1: HD/VD signal out (Internal)
D6 to D5:
Frame rate
00: 60 fps
01: 90 fps
10: 30 fps
11: 60 fps
D4:
No function
Always set “0”
D3:
Function mode (Caution)
0: Trigger
1: Normal
D2 to D0:
Scanning mode
000: Full scanning
001: 1/2 partial scanning
010: 1/4 partial scanning
111: Variable partial scanning
011 to 110: No function (Prohibited setting. Do not set these values)
Caution: 10H. D7, long exposure mode setting and this 11H.D3, function mode, interrelates to each other and
the combinations of both settings determine final operation modes of the camera. The functions of the cameras
determined by these two settings are summarized as below:
10H.D7
11H.D3
Long exposure
Function mode
Operational mode
1: ON
0: Trigger
Trigger mode with the long exposure enable
1: ON
1: Normal
Normal (continuous) mode
0: OFF
0: Trigger
Trigger mode without long exposure enable (Note)
0: OFF
1: Normal
Trigger mode without long exposure enable (Note)
Note: The camera goes into the normal (continuous) mode automatically when the trigger input lasts more than
500 mseconds.
STC-A33A
2. Descriptions of the Camera Control Commands (The underline settings are factory default settings)
User Guide 29 Rev 1.0
Page 30
Command No.
Command Descriptions
12H:
MOD3[7…0]
[The camera function mode 3] Initial data: MOD3[7…0] = 0
This sets the following camera function modes.
D[7…0]
D7
D6
D5
D4
D3
D2
D1
D0 D7 to D5:
No function
Always set “000”
D4 to D3
Exposure start mode
00: Normal
10 to 11 reset,
01: No function (Prohibited setting. Do not set these values)
D2:
No function
Always set “0”
D1 to D0:
Gamma mode
00: 1.0
01: 0.45
10 to 11: 1.0
13H:
MOD4[7…0]
[The camera function mode 4] Initial data: MOD4[7…0] =1
This sets the following camera function modes.
D[7…0]
D7
D6
D5
D4
D3
D2
D1
D0
D7 to D4:
No function
Set always “0000”
D3 to D0:
External sync
phase adjust
0111: 7CLK
0110: 6CLK
0101: 5CLK
0100: 4CLK
0011: 3CLK
0010:2CLK
0001: 1CLK
0000: 0CLK
1111: -1CLK,
1110:-2CLK
1101: -3CLK
1100: -4CLK
1011: -5CLK
1010:-6CLK
1001: -7CLK
1000: -8CLK
14H:
UART[7…0]
[The communication mode] Initial data: UART[7…0] = 0
This sets the following camera function modes.
D[7…0]
D7
D6
D5
D4
D3
D2
D1
D0 D7 to D2:
No function
Always set “000000”
D1 to D0:
Baud rate
00: 38,400bps
01: 9,600bps
10 to 11: No function
(Prohibited setting. Do not set these values)
20H:
SVR[7…0]
21H:
SVR[15…8]
[The exposure time (H) of the electronic shutter]
Initial data: SVR[15…0] = 0, data range: 0 to 4095
This and SHR[15…0] set the preset shutter speed (or CCD exposure time) for the electronic shutter.
The preset shutter speed is defined by the following formula:
Preset Shutter Speed = SVR[15…0] x (1H cycle time) + SHR[15…0] x (1CLK cycle time)
Notes:
1. The data in 20H through 23H reflects to the present shutter speed.
2. The camera works with the shutter off (maximum shutter speed) when both SVR[] and SHR[] are set to 0.
3. The camera works with the minimum shutter speed when this value is set to 0 and SHR[] is set between 1
and 306.
4. The value replaces by 4095 automatically when this value is set to greater than 4095.
STC-A33A
User Guide 30 Rev 1.0
Page 31
Command No.
Command Descriptions
22H:
SHR[7…0]
23:
SHR[15…8]
[The exposure time (CLK) of the electronic shutter]
Initial data: SHR [15…0] = 0, data range: 0 to 779
This and SVR[15…0] set the preset shutter speed (or CCD exposure time) for the electronic shutter.
The preset shutter speed is defined by the following formula:
Preset Shutter Speed = SVR[15…0] x (1H cycle time) + SHR[15…0] x (1CLK cycle time)
Notes:
1. The data in 20H through 23H reflects to the preset shutter speed.
2. The camera works with the shutter off (maximum shutter speed) when both SVR[] and SHR[] are set at 0.
3. The camera works with the minimum shutter speed when this value is set between 1 and 306 and SHR[] is
set to 0.
4. The value replaces by 779 automatically when this value is set to greater than 779.
24H:
PSR[7…0]
25H:
PSR[15…8]
[The start line of the variable partial scanning]
Initial data: PSR[15…0] =, data range: 0 to 493
This sets the start line number of the variable partial scanning area.
Actual start line of the variable partial scanning = this value + 1
Notes:
1. The camera works with full scanning when the value of (PSR[] + PSW[]) is greater than 494.
2. The value replaces by 493 automatically when this value is set greater than 493.
26H:
PWR[7…0]
27H:
PWR[15…8]
[The total effective line numbers in the variable partial scanning]
Initial data: PWR[15…0] = 494, data range: 0 to 494
The sets the number of the total effective lines (the image height) in the variable partial scanning.
Notes:
1. The camera works with full scanning when the value of (PSR[] + PSW[]) is greater than 494 or this value is
set to 0.
2. The value is replaced by 494 automatically when this value is set to greater than 494.
28H:
DLY [7…0]
[The delay time for the trigger] Initial data: DLY[7…0] = 0, data range: 0 to 31
This sets the delay time for the input trigger signal to the start of the exposure.
Delay time is defined by the following formula:
Delay Time = 148CLK x DLY[7…0] ( Unit is clocks)
Note: CLK = pixel clock time is µseconds
30H:
PGA[7…0]
[The CDS gain] Initial data; PGA[7…0] = , data range: 0 to 255
This sets the CDS gain, which is the programmable gain.
CDS gain is defined by the following formula:
CDS Gain = 3.64 + 0.132 x (PGA[7…0] + GOFS[7…0]) (Unit is dB)
The analog gain of CCD output is defined by the DCS gain as shown below:
Analog gain = pre-amp (6 dB) + CDS gain (Unit is dB)
STC-A33A
User Guide 31 Rev 1.0
Page 32
Command No.
Command Descriptions
31H:
DGB[7…0]
[The digital gain] Initial data: DGB[7…0] = The value in the address 0EH, data range: 0 to 255.
This sets the digital gain.
The video output level is defined by the following formula:
Video output level = (Input video level –CLAMP[7…0] x (1 + (DGB[7…0] / 128) + CLAMP [7…0])
Notes:
1. GOFS[7…0]: The gain offset, which is the value in the address 32H.
2. CLAMP[7…0]: The clamp level, which is the value in the address 38H.
32H:
GOFS[7…0]
[The gain offset] Initial data: GOFS[7…0] = The value in the address 0FH, data range: 0 to 63
This sets the gain offset.
38H:
CLAMP[7…0]
[The clamp level] Initial data: CLAMP[7…0] = The value in the address 0FH, data range: 0 to 63.
This sets the gain offset.
60H:
SW COM[7…0]
[Control selection (Rear panel / communication)] Initial data: SWCOM[7…0] = 0
This sets the following control selections.
D[7…0]
D7
D6
D5
D4
D3
D2
D1
D0 D7 to D2:
No function
Always set “000000”
D1:
Control selection
0: DIP switch on the camera
1: Communication
D0:
Gain switch
0: Enable
(Gain mode is selectable by the switch on the rear panel)
1: Disable
(Fixed gain is adjustable by the communication)
61H:
DA_VREF[7…0]
[DAC reference voltage]
Initial data: DA_VREF[7…0] = the value of the address 0DH, data range: 0 to 255
This sets the reference voltage for the DAC.
62H:
FIX_GAIN[7…0]
[Fixed gain for the rear panel] Initial data: FIX_GAIN[7…0] = 16, data range: 0 to 255
This sets the gain for the fixed gain on the rear panel.
0:6.544 dB, 255: 40,204 dB
63H:
VR_MAX[15…8]
64H:
VR_MAX[7…0]
[Maximum setting of the pot on the rear panel]
Initial data: VR_MAX[15…0] = 422, data range: 0 to 65535
This sets the maximum gain for the pot on the rear panel for the manual gain.
70H:
GAIN[15…8]
71H:
GAIN[7…0]
[The current gain selection on the rear panel / the current pot position on the rear panel]
This obtains the status of the gain selection and manual gain on the rear panel.
D[15…0]
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0 D15:
Gain mode
0:Manual gain
1: Fixed gain
D14 to D0:
Manual gain
STC-A33A
User Guide 32 Rev 1.0
Page 33
Command No.
Command Descriptions
74H:
DSW_ST[9…8]
75H:
DSW_ST[7…0]
[Status of the DIP switch on the rear panel]
This obtains the status of the DIP switch on the rear panel.
D[9…0]
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0 D9:
Binning mode
0: ON (Binning)
1: OFF (Normal)
D8:
Sync system
0: HD/ VD signals in (External)
1: HD/VD signals out (Internal)
D7 to D6:
Scanning mode
00: 1/4 partial scanning
01: 1/2 partial scanning
10 to 11: Full scanning
D5:
Trigger polarity
0: Negative
1: Positive
D4 to D3:
Reset mode
10: V-Reset
11: Non-Reset
D2 to D0:
Shutter speed
000: 1/20,000 seconds
001: 1/8000 seconds
010: 1/4,000 seconds
011: 1/2000 seconds
100: 1/1000 seconds
101: 1/500 seconds
110: 1/200 seconds
111: Shutter off, pulse width trigger
7EH:
FWVR[15…8]
7FH:
FWVR[7…0]
[Firmware version verification] Initial data: FWVR[15..0] = Firmware version
This is used for the firmware version verification when the camera is powered on.
The data of the address 10H to 7FH on the EEPROM are initialized with the factory default if this and the value
on the register are not equal.
80H:
E2P[7…0]
[EEPROM control] Initial data: E2P[7…0] = 0
This sets the EEPROM control mode.
D[7…0]
D7
D6
D5
D4
D3
D2
D1
D0 D7 to D2:
No function
Always set “000000”
D1:
Register simultaneously updates with the EEPROM
0: Prohibited
1: Permitted
D0:
Writing control into EEPROM
0: Prohibited
1: Permitted
Note 1: This bit is cleared to 0 automatically by the internal process after the execution of the command
Note 2: By synchronizing to the EEPROM read/write access, the subject control register is also updated.
STC-A33A
User Guide 33 Rev 1.0
Page 34
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Normal
90fps
OFF
Full
Scanning
1.0
Internal
80H
A8H
00H
External
28H
0.45
Internal
A8H
01H
External
28H
Partial full
scanning
1.0
Internal
88H
A8H
00H
External
28H
0.45
Internal
A8H
01H
External
28H
1/2 partial
scanning
1.0
Internal
A9H
00H
External
29H
0.45
Internal
A9H
01H
External
29H
1/4 partial
scanning
1.0
Internal
AAH
00H
External
2AH
0.45
Internal
AAH
01H
External
2AH
Variable
partial
scanning
1.0
Internal
AFH
00H
External
2FH
0.45
Internal
AFH
01H
External
2FH
ON
Full
scanning
1.0
Internal
90H
A8H
00H
External
28H
0.45
Internal
A8H
01H
External
28H
Partial
scanning
1.0
Internal
98H
A8H
00H
External
28H
0.45
Internal
A8H
01H
External
28H
1/2 partial
scanning
1.0
Internal
A9H
00H
External
29H
0.45
Internal
A9H
01H
External
29H
1/4 partial
scanning
1.0
Internal
AAH
00H
External
2AH
0.45
Internal
AAH
01H
External
2AH
Variable
partial
scanning
1.0
Internal
AFH
00H
External
2FH
0.45
Internal
AFH
01H
External
2FH
STC-A33A
3. Camera Control Commands (The camera function modes: address 10H, 11H, 12H)
a. Normal Mode (90fps)
User Guide 34 Rev 1.0
Page 35
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Normal
60fps
OFF
Full
Scanning
1.0
Internal
80H
88H
00H
External
08H
0.45
Internal
88H
01H
External
08H
Partial full
scanning
1.0
Internal
88H
88H
00H
External
08H
0.45
Internal
88H
01H
External
08H
1/2 partial
scanning
1.0
Internal
89H
00H
External
09H
0.45
Internal
89H
01H
External
09H
1/4 partial
scanning
1.0
Internal
8AH
00H
External
0AH
0.45
Internal
8AH
01H
External
0AH
Variable
partial
scanning
1.0
Internal
8FH
00H
External
0FH
0.45
Internal
8FH
01H
External
0FH
ON
Full
scanning
1.0
Internal
90H
88H
00H
External
08H
0.45
Internal
88H
01H
External
08H
Partial
scanning
1.0
Internal
98H
88H
00H
External
08H
0.45
Internal
88H
01H
External
08H
1/2 partial
scanning
1.0
Internal
89H
00H
External
09H
0.45
Internal
89H
01H
External
09H
1/4 partial
scanning
1.0
Internal
8AH
00H
External
0AH
0.45
Internal
8AH
01H
External
0AH
Variable
partial
scanning
1.0
Internal
8FH
00H
External
0FH
0.45
Internal
8FH
01H
External
0FH
STC-A33A
b. Normal Mode (60fps)
User Guide 35 Rev 1.0
Page 36
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Normal
30fps
OFF
Full
Scanning
1.0
Internal
80H
C8H
00H
External
48H
0.45
Internal
C8H
01H
External
48H
Partial full
scanning
1.0
Internal
88H
C8H
00H
External
48H
0.45
Internal
C8H
01H
External
48H
1/2 partial
scanning
1.0
Internal
C9H
00H
External
49H
0.45
Internal
C9H
01H
External
49H
1/4 partial
scanning
1.0
Internal
CAH
00H
External
4AH
0.45
Internal
CAH
01H
External
4AH
Variable
partial
scanning
1.0
Internal
CFH
00H
External
4FH
0.45
Internal
CFH
01H
External
4FH
ON
Full
scanning
1.0
Internal
90H
C8H
00H
External
48H
0.45
Internal
C8H
01H
External
48H
Partial
scanning
1.0
Internal
98H
C8H
00H
External
48H
0.45
Internal
C8H
01H
External
48H
1/2 partial
scanning
1.0
Internal
C9H
00H
External
49H
0.45
Internal
C9H
01H
External
49H
1/4 partial
scanning
1.0
Internal
CAH
00H
External
4AH
0.45
Internal
CAH
01H
External
4AH
Variable
partial
scanning
1.0
Internal
CFH
00H
External
4FH
0.45
Internal
CFH
01H
External
4FH
STC-A33A
c. Normal Mode (30fps)
User Guide 36 Rev 1.0
Page 37
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
90fps
OFF
Full
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
80H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
C0H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
V-Reset
Positive
Normal
1.0
Internal
81H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
C1H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A0H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
E0H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
V-Reset
Positive
Normal
1.0
Internal
A1H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
E1H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
STC-A33A
d. Trigger Mode (90fps, Full scanning)
User Guide 37 Rev 1.0
Page 38
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
90fps
OFF
Partial full
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
88H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
C8H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
V-Reset
Positive
Normal
1.0
Internal
89H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
C9H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A8H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
E8H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
V-Reset
Positive
Normal
1.0
Internal
A9H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
E9H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
STC-A33A
e. Trigger Mode (90fps, Partial full scanning)
User Guide 38 Rev 1.0
Page 39
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
90fps
OFF
1/2 partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
88H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
Negative
Normal
1.0
Internal
C8H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
V-Reset
Positive
Normal
1.0
Internal
89H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
Negative
Normal
1.0
Internal
C9H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A8H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
Negative
Normal
1.0
Internal
E8H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
V-Reset
Positive
Normal
1.0
Internal
A9H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
Negative
Normal
1.0
Internal
E9H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
STC-A33A
f. Trigger Mode (90fps, 1/2 partial scanning)
User Guide 39 Rev 1.0
Page 40
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
90fps
OFF
1/4 partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
88H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
Negative
Normal
1.0
Internal
C8H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
V-Reset
Positive
Normal
1.0
Internal
89H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
Negative
Normal
1.0
Internal
C9H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A8H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
Negative
Normal
1.0
Internal
E8H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
V-Reset
Positive
Normal
1.0
Internal
A9H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
Negative
Normal
1.0
Internal
E9H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
STC-A33A
g. Trigger Mode (90fps, 1/4 partial scanning)
User Guide 40 Rev 1.0
Page 41
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
90fps
OFF
Variable
partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
88H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
Negative
Normal
1.0
Internal
C8H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
V-Reset
Positive
Normal
1.0
Internal
89H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
Negative
Normal
1.0
Internal
C9H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A8H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
Negative
Normal
1.0
Internal
E8H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
V-Reset
Positive
Normal
1.0
Internal
A9H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
Negative
Normal
1.0
Internal
E9H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
STC-A33A
h. Trigger Mode (90fps, Variable partial scanning)
User Guide 41 Rev 1.0
Page 42
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
90fps
ON
Full
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
90H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
D0H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
V-Reset
Positive
Normal
1.0
Internal
91H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
D1H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B0H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
F0H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
V-Reset
Positive
Normal
1.0
Internal
B1H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
F1H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
STC-A33A
i. Trigger Mode (90fps, Binning, Full scanning)
User Guide 42 Rev 1.0
Page 43
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
90fps
ON
Partial full
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
98H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
D8H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
V-Reset
Positive
Normal
1.0
Internal
99H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
D9H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B8H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
F8H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
V-Reset
Positive
Normal
1.0
Internal
B9H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
Negative
Normal
1.0
Internal
F9H
A0H
00H
External
20H
0.45
Internal
A0H
01H
External
20H
H reset
1.0
Internal
A0H
10H
External
20H
0.45
Internal
A0H
11H
External
20H
STC-A33A
j. Trigger Mode (90fps, Binning, Partial full scanning)
User Guide 43 Rev 1.0
Page 44
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
90fps
ON
1/2 partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
98H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
Negative
Normal
1.0
Internal
D8H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
V-Reset
Positive
Normal
1.0
Internal
99H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
Negative
Normal
1.0
Internal
D9H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B8H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
Negative
Normal
1.0
Internal
F8H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
V-Reset
Positive
Normal
1.0
Internal
B9H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
Negative
Normal
1.0
Internal
F9H
A1H
00H
External
21H
0.45
Internal
A1H
01H
External
21H
H reset
1.0
Internal
A1H
10H
External
21H
0.45
Internal
A1H
11H
External
21H
STC-A33A
k Trigger Mode (90fps, Binning, 1/2 partial scanning)
User Guide 44 Rev 1.0
Page 45
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
90fps
ON
1/4 partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
98H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
Negative
Normal
1.0
Internal
D8H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
V-Reset
Positive
Normal
1.0
Internal
99H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
Negative
Normal
1.0
Internal
D9H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B8H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
Negative
Normal
1.0
Internal
F8H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
V-Reset
Positive
Normal
1.0
Internal
B9H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
Negative
Normal
1.0
Internal
F9H
A2H
00H
External
22H
0.45
Internal
A2H
01H
External
22H
H reset
1.0
Internal
A2H
10H
External
22H
0.45
Internal
A2H
11H
External
22H
STC-A33A
l. Trigger Mode (90fps, Binning, 1/4 partial scanning)
User Guide 45 Rev 1.0
Page 46
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
90fps
ON
Variable
partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
98H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
Negative
Normal
1.0
Internal
D8H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
V-Reset
Positive
Normal
1.0
Internal
99H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
Negative
Normal
1.0
Internal
D9H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B8H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
Negative
Normal
1.0
Internal
F8H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
V-Reset
Positive
Normal
1.0
Internal
B9H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
Negative
Normal
1.0
Internal
F9H
A7H
00H
External
27H
0.45
Internal
A7H
01H
External
27H
H reset
1.0
Internal
A7H
10H
External
27H
0.45
Internal
A7H
11H
External
27H
STC-A33A
m. Trigger Mode (90fps, Binning, Variable partial scanning)
User Guide 46 Rev 1.0
Page 47
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
60fps
OFF
Full
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
80H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
C0H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
V-Reset
Positive
Normal
1.0
Internal
81H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
C1H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A0H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
E0H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
V-Reset
Positive
Normal
1.0
Internal
A1H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
E1H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
STC-A33A
n. Trigger Mode (60fps, Full scanning)
User Guide 47 Rev 1.0
Page 48
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
60fps
OFF
Partial full
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
88H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
C8H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
V-Reset
Positive
Normal
1.0
Internal
89H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
C9H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A8H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
E8H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
V-Reset
Positive
Normal
1.0
Internal
A9H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
E9H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
STC-A33A
o. Trigger Mode (60fps, Partial full scanning)
User Guide 48 Rev 1.0
Page 49
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
60fps
OFF
1/2 partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
88H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
Negative
Normal
1.0
Internal
C8H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
V-Reset
Positive
Normal
1.0
Internal
89H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
Negative
Normal
1.0
Internal
C9H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A8H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
Negative
Normal
1.0
Internal
E8H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
V-Reset
Positive
Normal
1.0
Internal
A9H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
Negative
Normal
1.0
Internal
E9H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
STC-A33A
p. Trigger Mode (60fps, 1/2 partial scanning)
User Guide 49 Rev 1.0
Page 50
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
60fps
OFF
1/4 partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
88H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
Negative
Normal
1.0
Internal
C8H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
V-Reset
Positive
Normal
1.0
Internal
89H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
Negative
Normal
1.0
Internal
C9H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A8H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
Negative
Normal
1.0
Internal
E8H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
V-Reset
Positive
Normal
1.0
Internal
A9H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
Negative
Normal
1.0
Internal
E9H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
STC-A33A
q. Trigger Mode (60fps, 1/4 partial scanning)
User Guide 50 Rev 1.0
Page 51
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
60fps
OFF
Variable
partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
88H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
Negative
Normal
1.0
Internal
C8H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
V-Reset
Positive
Normal
1.0
Internal
89H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
Negative
Normal
1.0
Internal
C9H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A8H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
Negative
Normal
1.0
Internal
E8H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
V-Reset
Positive
Normal
1.0
Internal
A9H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
Negative
Normal
1.0
Internal
E9H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
STC-A33A
r. Trigger Mode (60fps, Variable partial scanning)
User Guide 51 Rev 1.0
Page 52
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
60fps
ON
Full
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
90H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
D0H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
V-Reset
Positive
Normal
1.0
Internal
91H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
D1H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B0H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
F0H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
V-Reset
Positive
Normal
1.0
Internal
B1H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
F1H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
STC-A33A
s. Trigger Mode (60fps, Binning, Full scanning)
User Guide 52 Rev 1.0
Page 53
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
60fps
ON
Partial full
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
98H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
D8H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
V-Reset
Positive
Normal
1.0
Internal
99H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
D9H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B8H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
F8H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
V-Reset
Positive
Normal
1.0
Internal
B9H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
Negative
Normal
1.0
Internal
F9H
80H
00H
External
00H
0.45
Internal
80H
01H
External
00H
H reset
1.0
Internal
80H
10H
External
00H
0.45
Internal
80H
11H
External
00H
STC-A33A
t. Trigger Mode (60fps, Binning, Partial full scanning)
User Guide 53 Rev 1.0
Page 54
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
60fps
ON
1/2 partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
98H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
Negative
Normal
1.0
Internal
D8H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
V-Reset
Positive
Normal
1.0
Internal
99H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
Negative
Normal
1.0
Internal
D9H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B8H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
Negative
Normal
1.0
Internal
F8H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
V-Reset
Positive
Normal
1.0
Internal
B9H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
Negative
Normal
1.0
Internal
F9H
81H
00H
External
01H
0.45
Internal
81H
01H
External
01H
H reset
1.0
Internal
81H
10H
External
01H
0.45
Internal
81H
11H
External
01H
STC-A33A
u. Trigger Mode (60fps, Binning, 1/2 partial scanning)
User Guide 54 Rev 1.0
Page 55
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
60fps
ON
1/4 partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
98H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
Negative
Normal
1.0
Internal
D8H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
V-Reset
Positive
Normal
1.0
Internal
99H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
Negative
Normal
1.0
Internal
D9H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B8H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
Negative
Normal
1.0
Internal
F8H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
V-Reset
Positive
Normal
1.0
Internal
B9H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
Negative
Normal
1.0
Internal
F9H
82H
00H
External
02H
0.45
Internal
82H
01H
External
02H
H reset
1.0
Internal
82H
10H
External
02H
0.45
Internal
82H
11H
External
02H
STC-A33A
v. Trigger Mode (60fps, Binning, 1/4 partial scanning)
User Guide 55 Rev 1.0
Page 56
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
60fps
ON
Variable
partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
98H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
Negative
Normal
1.0
Internal
D8H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
V-Reset
Positive
Normal
1.0
Internal
99H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
Negative
Normal
1.0
Internal
D9H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B8H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
Negative
Normal
1.0
Internal
F8H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
V-Reset
Positive
Normal
1.0
Internal
B9H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
Negative
Normal
1.0
Internal
F9H
87H
00H
External
07H
0.45
Internal
87H
01H
External
07H
H reset
1.0
Internal
87H
10H
External
07H
0.45
Internal
87H
11H
External
07H
STC-A33A
w. Trigger Mode (60fps, Binning, Variable partial scanning)
User Guide 56 Rev 1.0
Page 57
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
30fps
OFF
Full
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
80H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
C0H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
V-Reset
Positive
Normal
1.0
Internal
81H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
C1H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A0H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
E0H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
V-Reset
Positive
Normal
1.0
Internal
A1H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
E1H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
STC-A33A
x. Trigger Mode (30fps, Full scanning)
User Guide 57 Rev 1.0
Page 58
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
30fps
OFF
Partial full
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
88H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
C8H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
V-Reset
Positive
Normal
1.0
Internal
89H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
C9H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A8H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
E8H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
V-Reset
Positive
Normal
1.0
Internal
A9H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
E9H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
STC-A33A
y. Trigger Mode (30fps, Partial full scanning)
User Guide 58 Rev 1.0
Page 59
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
30fps
OFF
1/2 partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
88H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
Negative
Normal
1.0
Internal
C8H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
V-Reset
Positive
Normal
1.0
Internal
89H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
Negative
Normal
1.0
Internal
C9H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A8H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
Negative
Normal
1.0
Internal
E8H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
V-Reset
Positive
Normal
1.0
Internal
A9H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
Negative
Normal
1.0
Internal
E9H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
STC-A33A
z. Trigger Mode (30fps, 1/2 partial scanning)
User Guide 59 Rev 1.0
Page 60
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
30fps
OFF
1/4 partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
88H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
Negative
Normal
1.0
Internal
C8H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
V-Reset
Positive
Normal
1.0
Internal
89H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
Negative
Normal
1.0
Internal
C9H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A8H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
Negative
Normal
1.0
Internal
E8H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
V-Reset
Positive
Normal
1.0
Internal
A9H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
Negative
Normal
1.0
Internal
E9H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
STC-A33A
aa. Trigger Mode (30fps, 1/4 partial scanning)
User Guide 60 Rev 1.0
Page 61
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
30fps
OFF
Variable
partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
88H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
Negative
Normal
1.0
Internal
C8H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
V-Reset
Positive
Normal
1.0
Internal
89H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
Negative
Normal
1.0
Internal
C9H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
A8H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
Negative
Normal
1.0
Internal
E8H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
V-Reset
Positive
Normal
1.0
Internal
A9H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
Negative
Normal
1.0
Internal
E9H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
STC-A33A
bb. Trigger Mode (30fps, Variable partial scanning)
User Guide 61 Rev 1.0
Page 62
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
30fps
ON
Full
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
90H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
D0H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
V-Reset
Positive
Normal
1.0
Internal
91H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
D1H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B0H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
F0H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
V-Reset
Positive
Normal
1.0
Internal
B1H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
F1H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
STC-A33A
cc. Trigger Mode (30fps, Binning, Full scanning)
User Guide 62 Rev 1.0
Page 63
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
30fps
ON
Partial full
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
98H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
D8H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
V-Reset
Positive
Normal
1.0
Internal
99H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
D9H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B8H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
F8H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
V-Reset
Positive
Normal
1.0
Internal
B9H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
Negative
Normal
1.0
Internal
F9H
C0H
00H
External
40H
0.45
Internal
C0H
01H
External
40H
H reset
1.0
Internal
C0H
10H
External
40H
0.45
Internal
C0H
11H
External
40H
STC-A33A
dd. Trigger Mode (30fps, Binning, Partial full scanning)
User Guide 63 Rev 1.0
Page 64
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
30fps
ON
1/2 partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
98H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
Negative
Normal
1.0
Internal
D8H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
V-Reset
Positive
Normal
1.0
Internal
99H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
Negative
Normal
1.0
Internal
D9H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B8H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
Negative
Normal
1.0
Internal
F8H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
V-Reset
Positive
Normal
1.0
Internal
B9H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
Negative
Normal
1.0
Internal
F9H
C1H
00H
External
41H
0.45
Internal
C1H
01H
External
41H
H reset
1.0
Internal
C1H
10H
External
41H
0.45
Internal
C1H
11H
External
41H
STC-A33A
ee. Trigger Mode (30fps, Binning, 1/2 partial scanning)
User Guide 64 Rev 1.0
Page 65
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
30fps
ON
1/4 partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
98H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
Negative
Normal
1.0
Internal
D8H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
V-Reset
Positive
Normal
1.0
Internal
99H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
Negative
Normal
1.0
Internal
D9H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B8H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
Negative
Normal
1.0
Internal
F8H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
V-Reset
Positive
Normal
1.0
Internal
B9H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
Negative
Normal
1.0
Internal
F9H
C2H
00H
External
42H
0.45
Internal
C2H
01H
External
42H
H reset
1.0
Internal
C2H
10H
External
42H
0.45
Internal
C2H
11H
External
42H
STC-A33A
ff. Trigger Mode (30fps, Binning, 1/4 partial scanning)
User Guide 65 Rev 1.0
Page 66
Function
Mode
Frame
rate
Binnig
Scanning
Method
Trigger Mode
Reset Mode
Trigger
Polarity
Exposure
Start Mode
Gamma
Sync
System
Settings
10H
11H
12H
Trigger
30fps
ON
Variable
partial
scanning
Edge preset
Non-Reset
Positive
Normal
1.0
Internal
98H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
Negative
Normal
1.0
Internal
D8H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
V-Reset
Positive
Normal
1.0
Internal
99H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
Negative
Normal
1.0
Internal
D9H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
Pulse width
Non-Reset
Positive
Normal
1.0
Internal
B8H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
Negative
Normal
1.0
Internal
F8H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
V-Reset
Positive
Normal
1.0
Internal
B9H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
Negative
Normal
1.0
Internal
F9H
C7H
00H
External
47H
0.45
Internal
C7H
01H
External
47H
H reset
1.0
Internal
C7H
10H
External
47H
0.45
Internal
C7H
11H
External
47H
STC-A33A
gg. Trigger Mode (30fps, Binning, Variable partial scanning)
User Guide 66 Rev 1.0
Page 67
Rev
Date (D/M/Y)
Changes
Notes
1.0
2/9/2008
New Document
6/10/2009
Changed Command No. 28H:DLY [7…0] from (µseconds) to (clocks)
Pg. 31
STC-A33A
Revisions
User Guide 67 Rev 1.0
Page 68
STC-A33A
Sensor Technologies America, Inc.
1345 Valwood Pkwy, Suite 320
Carrollton, Texas 75006-6891
TEL (972) 481-9223 FAX (972) 481-9209
URL http://www.sentechamerica.com/
Sensor Technology Co., Ltd.
7F, Harada Center Building
9-17, Naka cho 4chrome
Atsugi-city, Kanagawa
243-0018 Japan
TEL +81-46-295-7061 FAX +81-46-295-7066
URL http://www.sentech.co.jp/
Taiwan Sensor Technology, Inc.
3F-6, No. 9, Aiguo W, Rd,. Jhong Jheng District
Taipei City 100, Taiwan, R.O.C.
TEL 886-2-2383-2331 FAX 886-2-2370-8775
EMAIL: [email protected]
User Guide 68 Rev 1.0
Loading...