Page 1
Catalog Number: Date: Project:
OVERVIEW
The CMR 9 Series Standard Range 360° occupancy sensor incorporates Passive Infrared (PIR)
detection technology into an attractive line powered occupancy sensor that provides amazing
sensitivity to small motions (e.g. hand movements) and excellent payback. The CMR 9 is an
economical solution for providing automatic lighting control where a wall switch replacement
sensor is not applicable. With an integrated line switching relay, the CMR 9 is perfect for
applications where locating a power pack is difcult, such as retrotting rooms with concrete or
inaccessible ceilings. For rooms with obstructions, the CMR PDT 9 Series sensor is recommended.
With optional ash programming via the Sensor Switch VLP mobile device application, the user
can easily change time delay, on mode and photocontrol settings.
FEATURES
• Push-Button Programmable, Adjustable Time Delays, and Multiple Operating Modes
• 100 Hour Lamp Burn-in Timer Mode
• No Field Calibration or Sensitivity Adjustments Required
• No Minimum Load Requirements
CMR 9
CMR PDT 9
Standard Range 360˚
Sensor
Warranty
Five-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/support/customer-support/terms-and-conditions
Note: Actual performance may differ as a result of end-user environment and application.
Specications subject to change without notice
C US LISTED
ORDERING INFORMATION
CMR 9 Example: CMR 9 ADC LT
CMR 9
Series Detection Technology Coverage Type Relay
CMR Ceiling Mount Sensor [blank] PIR
PDT Dual Technology
(PIR / Microphonics)
Control Type Voltage Visible Light Programming Temp/Humidity
[blank] None
1
D
DZ
P Photocell
ADC1Photocell w/ Dimming
Occupancy Controlled Dimming
2
Dual Zone Photocell
[blank] 120/277 VAC
347 347 VAC
9 Small Motion 360˚ [blank] Single Relay
2P Dual Relays
[blank] None
1,3
VLP
Visible Light
Programming
[blank] Standard
LT Low Temp/High Humidity
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitybrands.com/sensorswitch
© 2014-2019 Acuity Brands Lighting, Inc. All rights reserved. Rev. 06/18/19
Notes
1. Not available with 2P option.
2. Not available with single relay option.
3. PDT Required.
CMR 9
1 of 3
Page 2
COVERAGE PATTERNS
STANDARD RANGE 360º LENS
• Best choice for small motion (e.g. hand movements) detection
• Viewing angle of 56º in a 360º conical shaped pattern
• Provides 12 ft (3.66 m) radial coverage when mounted to standard 9 ft (2.74 m)
ceiling
• 8 to 15 ft (2.44 to 4.57 m) mounting heights provide 10 to 20 ft (3.05 to 6.10
m) radial coverage
Note: Screw axis is
aligned with a long
detection segment
12
3.7
SIDE VIEW
0 ft90 m
2.7
3.7 1.8 0 m 1.8 3.7
12 6 0 ft 6 12
TYPICAL WIRING SINGLE RELAY
STANDARD WIRING
BLACK* - Line Input
BLACK* - Load Output
WHITE - Neutral
347 VAC OPTION (347)
Black wires are replaced w/ Red wires
DIMMING OPTIONS (D, ADC)
VIOLET - Connect to Violet control wire from 0-10 VDC
dimmable ballast
GRAY - Connect to Gray common wire from ballast
INITIAL POWER UP
The sensor’s relay is shipped in a latched closed position so the lights will come on
upon initial power-up. If the lights do not immediately turn on (initial installation
only) the latching relay opened during shipment and will close within 30 secs.
Note: If the sensor loses power, the internal relay will latch to on.
*BLACK wires can be reversed
}
TOP VIEW
SENSORS IN PARALLEL
6
1.8
0 ft
0 m
6
1.8
12
3.7
Sensors may be wired in parallel; however, the maximum load
ratings stay the same. Do not wire sensors with P or ADC option in
parallel.
HOT
BLK BLK
BLK BLK
WHT
WHT
TYPICAL WIRING DUAL RELAY
STANDARD WIRING
BLACK* - Line Input 1
BLACK* - Load Output 1
BLUE** - Line Input 2
BLUE** - Load Output 2
WHITE - Neutral
347 VAC OPTION (347)
Black wires are replaced w/ Red wires
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitybrands.com/sensorswitch
© 2014-2019 Acuity Brands Lighting, Inc. All rights reserved. Rev. 06/18/19
*BLACK wires can be reversed
}
**BLUE wires can be reversed
}
N
LOAD
N
CMR 9
2 of 3
Page 3
SPECIFICATIONS
Electrical Input Ratings 120/277V, 80 mA, 50/60Hz
347V, 80 mA, 50/60Hz
480V, 80 mA, 50/60Hz
Output Ratings 120V, 800W/6.67A - Tungsten, Ballast
120V, 5A- General Purpose
277V, 1200VA/4.3A - Ballast
347V, 4.3A - General Purpose
480V, 5A - General Purpose
125V, 1/4HP - Motor
Relay Type Latching
Low Voltage Output Ratings 0-10VDC, Sinks <20mA
Class Rating
0-10V Dimming can be wired Class 1 or 2; Do not include if only Class 1
Standards/ Ratings Energy Management Equipment, UL916 (E167435)
Mechanical Dimensions 4.55”W x 1.55”D (116mm x 40mm)
Mounting Single-Gang or Octagonal Box, Surface Mount
Color White
Finish Matte
Connection Type Line Voltage Leads
Environmental Warrantied Operating Temperature: Standard: 14°F to 140°F (-10°C to 60°C)
LT Option: -4°F to 140°F (-20°C to 60°C)
Relative Humidity Up to 90%, Non-Condensing
Environment Indoor
Standards/ Ratings RoHS
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitybrands.com/sensorswitch
© 2014-2019 Acuity Brands Lighting, Inc. All rights reserved. Rev. 06/18/19
CMR 9 (TS-CMR-007A)
CMR 9
3 of 3
Loading...