Sennheiser Electronic MCR1G9 User Manual
SL MCR DW
Analog Out
PoE/Ctrl
Reset
123
45
Front Back
Product overview and operating elements
►
SL MCR DW
1 Status LEDs
• See „Meaning of the status LEDs“
2 Analog Out 3-pin socket
• Analog audio output (see „Connecting the receiver“)
• Suitable for Phoenix Contact MCVW 1.5-3-ST-3.81
3 Reset button
• To restore the factory settings
•Hold for 5 seconds
4 Dante I RJ-45 socket
• Digital audio output (see „Connecting the receiver“)
5 Dante II / PoE / Ctrl RJ-45 socket
• Digital audio output (see „Connecting the receiver“)
• PoE supply (Power over Ethernet) (see „Putting the receiver into operation“)
• Configuration via the software or a media control system (see „Controlling and monitoring the receiver via the network“)
2
SL MCR DW
PoE /
network control
digital audio
PoE /
network control
digital audio digital audio
PoE /
network control
digital audio
Variant 1 Variant 2 Variant 3
Connecting the receiver
The receiver can output analog and digital audio signals.
The analog audio signal is output via the 3-pin Analog Out terminal.
Digital audio signals are output via the Dante interface with two RJ-45
sockets. This interface is also used for control and configuration via the
network and for Power over Ethernet supply.
The following variants are possible:
►
3
SL MCR DW
Analog Out
PoE/Ctrl
Reset
PoE
Analog Out
PoE/Ctrl
Reset
PoE/Ctrl
Control Cockpit clients
optional
optional
Control Cockpit
host PC (opt. client)
Media control client
LAN
Application example:
LAN or WiFi
Media control server
LAN
or WiFi
Connecting to the network (power supply and configuration)
The PoE/Ctrl RJ-45 socket (Dante I) is used to both power the receiver via
Power over Ethernet and configure it using the Sennheiser Control Cockpit software (see „Controlling and monitoring the receiver via the net-
work“).
▷ In your network you can either use a switch that provides PoE or a PoE
injector.
►
4
SL MCR DW
Analog Out
PoE/Ctrl
Reset
Analog Out
PoE/Ctrl
Reset
PoE/Ctrl
Dante™ DSP
PriSec
PoE
LAN
LAN
Application example:
Analog Out
Analog Out
PoE/Ctrl
Reset
Analog Out
suitable for
Phoenix Contact MCVW 1.5-3-ST-3.81
Outputting digital audio signals
The Dante™ interface with two RJ-45 sockets, Dante I and Dante II, is used
for outputting digital audio signals. The interface supports redundant output.
►
Outputting analog audio signals
Use the Analog Out socket to output analog audio signals.
►
5
SL MCR DW
Mounting the receiver
Safety instructions for installation
Observe the following safety instructions when installing the product.
▷ The physical mounting and all electrical installations must be per-
formed by a specialist.
▷ The specialist must have sufficient professional training, experience
and knowledge of applicable provisions, regulations and standards to
be able to properly assess the work assigned to them, identify possible
hazards and take appropriate safety measures.
▷ When mounting the product, observe and follow all local, national and
international regulations and standards.
center
line
The receiver can be mounted in the following ways.
Mounting the receiver on the wall
To mount the receiver on the wall, you will need the mounting frame supplied.
Screws and anchors for mounting the product to the wall are not included with delivery. Use screws and anchors that are appropriate
for the particular characteristics of your wall.
►
>1,5 m>1.5 m>1,5 m>1,5 m
center
line
center
line
top
wall mount
VESA 100
center
line
6
Loading...