Page 1
Page 2

Bild1a
Fig.1a
Das MD 429 "Studiosound« ist ein dynamisches Musiker-Mikrofon der
Spitzenklasse. Es erfüllt in besonderem Maße die Anforderungen der
Tonstudio-Technik. Als Besonderheiten sind die hohe Popp-Festigkeit,
der geringe Nahbesprechungseffekt und die große Rückkopplungs-
sicherheit hervorzuheben. Einweiteres Qualitätsmerkmal ist die her-
vorragende Körperschalldämmung, die durch eine aufwendige, federnde
Systemlagerung erzielt wurde. Der Studio-Technik entsprechend wurde
das MD 429 mit einem 3poligen Cannon-Steckverbinder ausgestattet.
Zum Lieferumfang gehört eine Schnellwechselklemme, die mit einem
Wechselgewinde zur Befestigung auf Stativen mit 3/8"-' '/2"- und
5/s"x27G-Gewinden ausgerüstet ist.
Stellungfür
Schnellwechsel betrieb
Unlocked position
Position pour
changement rapide
Mikrofon verriegelt
Locked position
Verrouillage du
microphone
Bild1 b
Fig.1 b
Aufstellungs- und Anschlußhinweise
Die zum Lieferumfang des Mikrofons gehörende Schnellwechselklemme
läßt zwei Gebrauchsstellungen zu. Wird das Mikrofon nur leicht in diese
Klemme eingesteckt, so kann es schnell und einfach wieder heraus-
gezogen werden (Bild 1 a). Wird es dagegen über den ersten Anschlag
hinaus inder Klemme nach hinten gedrückt, so rastet esfestein und kann
dann in der Klemme hängend in jede beliebige Gebrauchsstellung ge-
bracht werden, ohne daß die Gefahr besteht, daß es herausfällt (Bild 1 b).
Durch kräftiges Ziehen nach vorn kann diese Verriegelung wieder gelöst
werden.
Das im Sockel der Schnellwechselklemme befindliche Gewindestück
kann mit Hilfe einer Münze herausgeschraubt werden. Ab Werk ist es zur
Befestigung auf %" -Gewinden vorbereitet. Wird es herausgeschraubt
und umgekehrt wieder eingesetzt, kann die Klemme für '/2"-Gewinde
benutzt werden. Entfernt man das Gewindestück ganz, paßt der Sockel
auf 5/s"x27G-Gewinde (Bild 2).
Das MD 429 hat eine elektrische Impedanz von 200 Q und ist symme-
trisch beschaltet (Bild 3). Es kann sowohl an symmetrische als auch
unsymmetrische Geräteeingänge angeschlossen werden, deren
Impedanz mindestens 1000 Q betragen sollte. Die Länge des Anschluß-
kabels kann mehr als 100 m betragen.
Schaltschema U
Bild3
a
.--,<.-
~
Bild2
Fig.2
Page 3

AkustischeArbeitsweise
Obertragungsbereich
Richtcharakteristik . . . . . . . . . . . .
RichtungsmaBbel1000 Hz (Auslöschung)
Feldleerlautübertragungsfaktorbei1kHz
ElektrischeImpedanzbei1kHz
MinimaleAbschluBimpedanz
Stecker
Steckerbeschaltung
Anschlußkupplung
Magnetfeld-Störtaktor
Abmessungen
Gewicht
Dru ckg radlente nempfänge r
50 . 16000 Hz
Superniere
bel 120": 22 dB-3 dB
1,4 mV/Pa f:; 0,14 mV/~bar
:t 2.5 dB
200 Q
1000 Q
3pol. Switchcraft (Cannon)
2 u. 3 ~ Tauchspule
1 u. Steckergehäuse ~ Masse
3pol. SWltchcraft A 3 F
(Cannon XLR-3-IIC)
"'5~V/5~T
Glltf max. 31 mm 0
Korb 49 mm 0
Längeca. 200 mm
ca.220 9
Zubehör
Stativ MZS 144
Sehr robustes Stativ. Höhe veränderlich zwischen 84 und 158 cm.
Füße abschraubbar.
Stativ MZS 210
Sehr robuste Ausführung mit federgelagerten, zusammenklappbaren
Füßen. Unterdrückt wirksam Trittschall. Höhe veränderlich zwischen
84 cm und 158 cm.
Tischfuß MZT 441
Stabiler und feststehender Tischfuß für Studio-Betrieb.
Anschlußkabel KA 7 U
Beidseitig mit Cannon-Steckverbindern ausgerüstet. Länge: 7,5 m.
Anschlußkabel MZK 431 U-K
Für den Anschluß des MD 429 an unsymmetrische Eingänge mit 6,3 mm
Klinkenbuchse.
Page 4

The MD 429 "Studiosound" is atop-class, dynamic musician's micro-
phone which has been built with the special needs 01recording studios in
mind. Special leatures are its high insensitivityto 'pop'noise, itsminimized
proximity effect and its outstanding leedback prevention. A lurther
indication 01this microphone's quality is given by the excellent
insensitivity to handling noise afforded it by its sophisticated internal
suspension system. As a lurther step towards meeting the demands 01
recording studios the MD 429 was litted with a 3-pin Cannon plug-
connector.
Included in the packaging is a quick-release clamp litted with a
reversible thread insert lor mounting onto Iloor stands with %" -, '/2" - and
5/8''x27G-threads.
Mounting and connecting the microphone
The quick-release clamp supplied with the microphone leatures two
'different working-positions. II the microphone is only lightly inserted into
the clamp, it can be quickly and easily removed (Iig. 1a). 11,on the other
hand, the microphone is pushed over the lirst stop right to the back 01the
clamp it is then locked into position. The clamp can now be set at any
angle without lear 01thk microphone lalling out (Iigure 1 b). The micro-
phone is 'unlocked' by lirm pulling.
The thread insert situated in the socket at the lower end 01the quick-
release clamp can be unscrewed with the aid 01a coin. On leaving the
lactory it is readylormounting onto %" threads. Ilthe insert is unscrewed,
turned around and replaced the clamp can now be affixed to '/2"-threads.
II the insert is removed entirely, the socket will lit aIl5/s"x27G threads
(Iigure 2).
The MD 429 is balanced (Iigure 3) and has an electrical impedance 01
200 Q. It can be connected to both balanced and unbalanced inputs as
long as they have an impedance 01aleast 1000 Q. The length 01the
connecting cable may exceed 100 m without problems.
Aeoustiealmodeofoperation
Frequeneyresponse
Dlleetlonaleharaetenstle
Releetionat 1000 Hz
Openeireultoutputvoltageat 1kHz
Eleetrieal impedanee at 1 kHz
Minimum load impedanee
MierODhone eonneetor
Conneetor wiring
..
I
Cableeonneetor
Magnetie interferenee
Dimensions
Weight
pressure gradient receiver
50 16000 Hz
super eardioid
at 120°; 22 dB - 3 dB
1.4 mV/Pa ~ 0.14 mV/~bar
:+:25 dB
200 Q
1000 Q
3-pin Switeheraft (Cannon)
2 and 3 ~ movingeoil
1andeonneetorhousing ~
ground
3-pin Switeheraft A3F
(Cannon XLR-3-IIC)
:;;5~V/5~T
handle max. 31 mm 0
basket 49 mm 0
length approx. 200 mm
approx. 220 g
Wiring Diagram U
---><-
Fig.3
Accessories
i
Floor stand MZS 144
Heavy duty Iloor stand. Height adjustable between 84 and 158 cm. Legs
are detachable.
Floor stand MZS 210
De luxe, heavy dutylloorstand with anti-vibration, loldable legs. Ellectively
suppresses lootfall. Height adjustable between 84 cm and 158 cm.
Desk stand MZT 441
Highly stable desk stand lor studio use.
Connecting cable KA 7 U
Fitted at both ends with Cannon plug-connectors. Length: 7.5 m.
Connecting cable MZK 431 U-K
For connecting the MD 429 to all unbalanced inputs with a 6.3 mm jack
socket.
Page 5

Le MD 429 "Studiosound" est un microphone dynamique de laplus haute
qualite, destine ala musique. 11repond tout specialement aux exigences de
la technique du studio de sonorisation. On soulignera en particulier son
insensibilite aux "Popp", son faible effet de proximite et sa grande
resistance aux effets de retroaction.
Oe plus il presente I'avantage d'amortir parfaitement les bruits de choc,
grace a une suspension anti-vibratoire. Comme il est destine a la
technique de studio, le MD 429 a ete equipe d'un raccord Cannon
tripolai re.
Une pince de fixation rapide, jointe au MD 429, permet la fixation sur
pied de 3/8'" '/2" et %"x27G de filet, grace a un taraudage multiple
transformable.
Instructionsde montage et de raccordement
La pince de fixations rapide livree avec le microphone permet de
maintenir le micro de deux fayons differentes: pour deposer et reprendre
le micro rapidement, ne I'insererdans lapincequetreslegerement(fig. 1a).
Lorsqu'il est insere dans la pince, vers I'arriere, jusqu'au cran, 'il sera
alors maintenu fermement dans la pince et pourra ainsi iHre positionne a
volonte, sans qu'il risque d'en glisser (fig. 1 b). Pour le liberer de la pince,
tirer le micro fermement vers I'avant.
Le taraudage se trouvant dans le socle de la pince de fixation rapide est
une piece que vous pouvez devisser tout simplement au moyen d'une
piece de monnaie. Teile qu'elle est montee a la livraison, elle s'adapte a
un filet de %". Apres I'avoir devissee et reinseree a I'envers, elle
s'adaptera a un filet de '/2'" En enlevant completement cette piece de
taraudage,lesocledela pinces'adapteraaunfilet de %"x27G (fig. 2).
Le MD 429 a une impedance electrique de 200 Q et il est connecte
symetriquement (fig. 3). 11peut etre raccorde aussi bien a des entrees
symetriques qu'asymetriques, mais dont I'impedance devrait etre au
moins de 1000 Q.
La longueur du cable de raccordement peut aller jusqu'a plus de 100 m.
Principe acoustique
Bande passante
Directivite
Gain directit a 1000 Hz
Senslbiiite a 1 kHz
Impedancea 1kHz
Impedancenominaledecharge
Connecteur
Brochage
Couplageconnecteur
FacteurdesenSlbiliteauxchampsmagnetiques
Dimensions
Poids
capteurdegradientd'interference
50 16000 Hz
hypercardio"ide
a 120°:22 dB- 3dB
1,4mV/Pa;;' 0,14 mV/~bar
:!:2.5 dB
200 Q
1000 Q
Switchkrafttripoialfe
(Cannon)
2et3 ~ bobinemobile
1et boitier = masse
SwitchkrafttripolaireA3 F
(CannonXLR-3-IIC)
;';;5~V/5~T
Poignee: 31 mm 0 max.
Boitier: 49 mm 0
Langueur: env. 200 mm
env. 220 g
Schemade
branchementU
--
Fig.3
Accessoires
Pied MZS 144
Pied tres solide. Hauteur reglable de 84 cm a 158 cm. Pieds devissables.
Pied MZS 210
Tres resistant et solide. Equipe de pieds pliables et a suspension; bruits
de pas amortis. Hauteur reglable de 84 cm Ei158 cm.
MZT441
Piedde tablesolideetstablepourfonctionnementenstudio.
Cäble de raccordement KA 7 U
Longueur 7,5 m, equipe aux deux bouts de connecteurs Cannon
Cäbles de raccordement MZK 431 U-K
Pour le raccordement du MD 429 a des entrees asymetriques a douille
de 6,3 mm.
Page 6