Sennheiser I30H-S User Manual

General Description

Sennheiser’s modular Installed Sound Series microphones kits for podium, hanging, boundary layer and table stand applications facilitate all possible installation conﬁgurations at affordable prices. At the heart of the series are three superbly engineered capsules: the ME 34 cardioid, the ME 35 super cardioid and the unique lobar-patterned ME 36 mini shotgun. Each capsule can interface with three different goosenecks: the 15 cm MZH 3015 (6"), the 40 cm MZH 3040 (15.75") and the dual ﬂex 40 cm MZH 3042 (15.75"), all designed to maintain proper capsule placement. Each system requires 12-48 volt phantom power. All contact points are gold plated and corrosion resistant. All components have anti-reﬂective matte black surfaces.

ME35

MZC30

MZH30

ME 35

Polar Pattern

Frequency Response Graph

Microphones | Installed Sound

Kit Includes:

ME 35 Capsule MZC 30, MZH 30 Ceiling Hanger

i30H-S

Technical Data

Acoustic operating principle Pressure gradient transducer Pick-up pattern Super-cardioid Frequency response 50–20,000 Hz Sensitivity (free ﬁeld, no load) 10 mV/Pa Electrical impedance 50 Ω Min. terminating impedance 1 KΩ Equivalent noise level 26 dB-A 37 dB-CCIR Power supply P 12–P 48 Dimensions .47" x .71" (11.93mm x 18.04mm) Weight .34 oz. Connector XLR-3

.69"

[17.53mm]

Ø.48"

[12.19mm]

150˚

120˚

90˚

30˚

60˚

90˚

120˚

150˚

180˚

125 Hz 250 Hz 500 Hz 1000 Hz

2000 Hz 4000 Hz 8000 Hz 16000 Hz

Super cardioid patterned condenser microphone capsule. Provides a high degree of isolation.

i30H-S

Architects Speciﬁcations

The hanging mic system shall be modular and facilitate integration of different polar-patterned capsules. It must utilize a condenser transducer element operational with 48v phantom power and have a frequency response of 50 Hz–20,000 Hz. The transducer must have super cardioid directional characteristics and also be small and streamlined, no longer than 18 mm (.71") with a diameter no larger than 12.2 mm (.48"). The 9 meter (29.5')hanging cable must have a 1 mm (.04") thickness, be Kevlar reinforced, and terminate to a pre-amp housed XLR connector. The system must maintain strict on axis positioning using a low mass wire hanger with a 2 mm (.08") thickness. The system must be a Sennheiser i30H-S.

Limited Product Warranty/Service

Sennheiser Electronic Corporation extends the following limited product warranty for Sennheiser products:

The warranty period for all covered Sennheiser products is two years from the date of purchase. Not covered by this warranty are accessories and other consumables; for example, items of wear and tear, such as cables. During the warranty period, Sennheiser Electronic Corporation warrants that the Sennheiser equipment will be free from defects in materials and workmanship used in making the product. Abnormal conditions, deliberate abuse and damage due to accidents, operator’s error, or unauthorized service attempts are excluded from any warranty claims.

Under this warranty, Sennheiser Electronic Corporation will repair, or at its option, replace free of charge the covered defective Sennheiser product, provided it is returned (postage paid, with proof of purchase from the original seller) to a Sennheiser Service Facility. Products should be returned in their original package, or otherwise suitably protected to avoid shipping damage. Either product registration or a valid, dated proof of purchase is accepted to establish the warranty period. The Sennheiser Service Department will be the sole authority to determine the validity of all warranty issues.

This Limited Product Warranty is Sennheiser Electronic Corporation’s only warranty, and the customer’s only remedy concerning Sennheiser products. All other representations and warranties, express or implied, written or oral, including, but not limited to, any warranties of merchantability, ﬁtness for a particular purpose, or non-infringement, are expressly excluded. As a result, except as set forth in the previous paragraphs, the product is sold “as-is” and the customer is assuming the entire risk as to the product’s suitability for his needs, its quality and its performance.

In no event will Sennheiser Electronic Corporation be liable for direct, indirect, special, incidental or consequential damages resulting from any defect in the product or from its use, even if advised of the possibility of such damages.

i30H-S

.34"

[8.6mm]

.53"

[13.5mm]

3.13"

[79.5mm]

3.89"

[98.8mm]

1.78"

[45.2mm]

105º

Ø.04"

[1.0mm]

The MZH 30 is a lightweight (0.1 oz) hanger accessory designed to interface with ME 34, ME 35 and ME 36 capsules. Its nearly invisible 1.1 mm diameter black wire design is durable and strictly maintains on-axis placement.

MZH 30

.98"

[24.9mm]

1.86"

[47.2mm]

4.23"

[107.4mm]

.97"

[24.6mm]

2.65"

[67.3mm]

Ø.32"

[8.1mm]

Ø.75"

[19.0mm]

MZC 30

The MZC 30 is a 9 m (28') cable for hanging applications of the ME 34, ME 35 and ME 36 capsules and boundary layer application of the ME 36 capsule. The sturdy 1 mm Kevlar reinforced cable has a copper core and terminates to an XLR connectorized preamp to accommodate P48 powering.