Page 1
Audio
Distribution
Network
ADN C1/ADN D1
Quick guide
Page 2
Information on this quick guide
Information on this quick guide
Please make sure to read the “Safety information” supplement
included separately with the ADN CU1 central unit. This supplement
contains important information on the safe operation of the product as
well as the manufacturer’s declaration and warranty notes.
A detailed instruction manual for the overall ADN conference system
www
www.sennheiser.com
Manual
can be found
• on the Internet at www.sennheiser.com or
• on the DVD-ROM supplied with the ADN CU1 central unit.
The ADN D1 and ADN C1 conference units
The ADN D1 delegate unit and the ADN C1 chairperson unit are part of
the Sennheiser ADN conference system.
To ensure full operational reliability in a redundant ring topology, the hardware of the ADN C1 and ADN D1 has been revised.
If you combine conference units with hardware revision 1 (no
marking on the type plate) and conference units with hardware
revision 2 (“HW: v2” is printed on the type plate), fail-safe
operation is only possible to a limited extent.
왘 In a redundant ring topology, only use conference units
with hardware revision 2.
Delivery includes
1 ADN D1 delegate unit or
ADN C1 chairperson unit
1 quick guide
IN OUT
ADN C1/ADN D1 | 1
Page 3
Delivery includes
Components required for operation
Central unit/
Power supplies
Conference units
Number Description Cat. No. Function
1 ADN CU1-EU central unit,
EU version
ADN CU1-UK central unit,
UK version
ADN CU1-US central unit,
US version
1 - 15
(optional)
Number Description Cat. No. Function
Max. 400 ADN D1 delegate unit 502758 Allows to make
1 - 10
(optional)
ADN PS-EU power supply,
EU version
ADN PS-UK power supply,
UK version
ADN PS-US power supply,
US version
ADN C1 chairperson unit 502759 Allows to manage
505553 Controls the
conference and
505554
505555
505546 Supplies power to
505547
505548
supplies power
to max. of 40
conference units
conference units
connected in
simple strings or
in redundant ring
topology,
for conferences
with up to 400
conference units
contributions to
the conference
the conference
System cables
2 | ADN C1/ADN D1
The system cables are black and have two shielded RJ45 plugs.
Number Description, length Cat. No. Function
Divers SDC CBL RJ45-2, 2 m 009842 Allow to
SDC CBL RJ45-3, 3 m 009843
SDC CBL RJ45-5, 5 m 009844
SDC CBL RJ45-10, 10 m 009845
SDC CBL RJ45-20, 20 m 009846
SDC CBL RJ45-50, 50 m 009847
Additional accessories for the ADN conference system can be
found at www.sennheiser.com.
interconnect
components and
conference units
Page 4
Product overview
Product overview
ADN C1 ADN D1
Sound inlet basket with windshield
Signal light ring
Headphone socket
Priority key
Next key
Headphone volume control for
headphone socket
Microphone key
Microphone LED
Loudspeaker
IN socket
OUT socket
ADN C1/ADN D1 | 3
Page 5
Operating a delegate unit
Operating a delegate unit
Taking the floor/Making a request to speak
If the conference mode is set to “Direct Access” or “Override” (for fur-
ther information, refer to the detailed instruction manual for the overall system “ADN Conference System”):
왘 Press the microphone key .
Your microphone switches on and you can take the floor immediately. The microphone LED and the signal light ring light up
red. The loudspeaker is muted. Depending on the conference
mode and the speaker limit set, the microphone of the previous
speaker will be deactivated.
If the conference mode is set to “Push To Talk”:
왘 Press the microphone key and keep it pressed for the duration
of your contribution.
Your microphone switches on and you can take the floor immediately. The microphone LED and the signal light ring light up
red. The loudspeaker is muted.
If the conference mode is set to “Request”, you have to be granted
speaking privileges:
왘 Press the microphone key .
Depending on the setting adjusted in the operating menu (for further information, refer to the detailed instruction manual for the
overall system “ADN Conference System”)
– the microphone LED flashes green and the signal light ring
flashes red or
– only the microphone LED flashes green.
When the chairperson grants you speaking privileges, your micro-
phone is activated. The microphone LED and the signal light
ring light up red. The loudspeaker muted. Depending on the
conference mode and the speaker limit set, the microphone of the
previous speaker will be deactivated.
4 | ADN C1/ADN D1
Page 6
Operating a delegate unit
쐋
Vol +
Vol -
Deactivating the microphone/Cancelling a request to speak
To deactivate the microphone when you have finished speaking or to cancel a request to speak (“Direct Access”, “Override” or “Request” mode):
왘 Press the microphone key once more.
The microphone LED and the signal light ring go off.
In “Push To Talk” mode:
왘 Release the pressed microphone key .
The microphone LED and the signal light ring go off.
Connecting headphones
왘 Connect headphones with a 3.5 mm jack plug to the headphone
socket .
Adjusting the headphone volume
CAUTION
Hearing damage due to high volumes!
Listening at high volume levels for long periods can lead
to permanent hearing defects.
왘 Set the volume to a medium level.
왘 Do not continuously expose yourself and other con-
ference participants to high volumes.
To adjust the volume:
왘 Turn the headphone volume control
– to the right to increase the volume or
– to the left to reduce the volume.
At switch-off, the headphone volume is reset to a medium level.
ADN C1/ADN D1 | 5
Page 7
Operating a chairperson unit
Operating a chairperson unit
Beside the chairperson functions, chairperson units offer the same
functions as delegate units. A chairperson unit allows you to take the
floor at any time without having to “apply” for a comment. If your conference system comprises several chairperson units, all chairperson
units have equal rights.
Granting speaking privileges
All participants who have made a request to speak will join a requestto-speak list. Depending on the setting adjusted in the operating
menu:
To grant speaking privileges to the next participant from the requestto-speak list:
왘 Press the Next key .
– the microphone LED flashes green and the signal light ring
flashes red or
– only the microphone LED flashes green.
The next participant from the request-to-speak list is granted
speaking privileges.
If you are using the “Conference Manager” software, you
can also grant speaking privileges with a mouse click (for
further information, refer to the detailed instruction manual
for the overall system “ADN Conference System”).
6 | ADN C1/ADN D1
Ending a conference or withdrawing speaking privileges
(cancel function)
왘 Set the function of the chairperson unit’s priority key “Clear
Request List on Cancel”) via the central unit’s operating menu:
Main Menu
Conference
Clear Request List on Cancel
Page 8
Operating a chairperson unit
왘 Briefly press the priority key .
Muting all delegate units temporarily (priority function)
Using the priority function, the chairperson can interrupt a discussion
at any time. The speaking privileges of all chairperson units remain
active at any time.
왘 Keep the priority key pressed for as long as you want to mute
왘 Release the priority key .
Setting Function of the priority key
“On” Pressing the priority key deactivates all delegate
units.
All requests to speak are deleted.
“Off” Pressing the priority key deactivates all currently
active delegate units.
All requests to speak are retained.
The conference system behaves as set.
If you are using the “Conference Manager” software, you
can also deactivate all delegate units with a mouse click (for
further information, refer to the detailed instruction manual for the overall system “ADN Conference System”).
the delegate units.
All conference units – except for the chairperson units – are muted
immediately. The microphone LED and the signal light ring of
the previously active conference units flash red. You can take the
floor immediately.
The muting of the conference units is canceled. The discussion is
continued.
ADN C1/ADN D1 | 7
Page 9
Specifications
Specifications
ADN D1 and ADN C1 conference units
Dimensions
(w/o gooseneck) 185 x 63 x 140 mm (W x H x D)
Weight approx. 700 g
Supply voltage 35 V ... 52.8 V
Power consumption 2 W (w/o reproduction via loudspeakers)
Temperature range operation: +10°C to +40°C
storage: −25°C to +70°C
Relative humidity operation: 10 to 80%
storage: 10 to 90%
Headphone socket 3.5 mm stereo jack socket
Output level at
headphone socket 50 mW/16 Ω
DHT (at 1 kHz) 0.03% at 50 mW/16 Ω
Loudspeaker
8 | ADN C1/ADN D1
Frequency response 100 Hz to 14.5 kHz
Signal-to-noise ratio > 70 dB(A)
Microphone
Pick-up pattern super-cardioid
Frequency response 190 Hz to 14.5 kHz
Page 10
Sennheiser electronic GmbH & Co. KG
Am Labor 1, 30900 Wedemark, Germany
www.sennheiser.com
Publ. 09/11, 543390/A01
Bedienungsanleitung
Instruction manual
Notice d’emploi
Instrucciones de uso
Istruzioni per l’uso
Gebruiksaanwijzing
Loading...