SENDO Advance Instruction Manual

INSTRUCTION MANUAL

Digital blood presure monitor

ADVANCE

TM

Index Mark

Display

Air Socket

Air Connector Plug

Air Hose

Battery Cover

Battery Compartment

1.5V Batteries
(R6P, LR6 or AA)

Proper Fit Range

Arm Cu

DC Jack

START Button

AC Adapter Plug

Introduction

Thank you for purchasing a state-of-the-art Sendo blood pressure monitor. Sendo
will give you years of accurate measurements, if it is used properly. We are always
ready to provide help on our telephone lines for your country.

5 years guarante.

Please read carefully the instructions before measuring using this blood pressure
monitor

2

Installing / Changing The Batteries

Remove the battery cover.

Remove the used batteries and insert new
batteries into the battery compartment as shown,
taking care that the polarities (+) and (-) are
correct.

Replace the battery cover.

Use only R6P, LR6 or AA batteries.

Connecting the Air Hose

Insert the air connector plug
into the air socket rmly.

Connecting the AC Adapter

Insert the AC adapter plug into the DC jack.
Then, insert the AC adapter into an electrical
outlet.

The AC adapter, the model TB-240, is sold
separately.

Note: When the AC adapter is pulled out,
the memories are cleared.

1

1

2

3

2

3

Air Socket

Air Connector Plug

Air Hose

AC Adapter Plug

DC Jack

3

Measurements

SENDO Advance is designed to detect the pulse and to inate the cu to a systolic
pressure level automatically.

If your systolic pressure is expected to exceed 230 mmHg, read
"Measurement with the Desired Systolic Pressure" on the next page.

Sit comfortably in a chair with your
feet at on the oor. Place your left
arm on a table at a slight angle.

Wrap the cu around the upper
arm, about 2 - 3 cm above the
elbow, as shown.

Place the cu directly against
the skin, as clothing may
cause a faint pulse and result
in a measurement error.

Constriction of the upper
arm, caused by rolling up a
shirtsleeve, may prevent
accurate readings.

Conrm that the index
points within the proper t
range.

1

2

Arm Cu

Index Mark and Proper t range

Air Hose

2-3 cm

4

Place the cu on the arm
(preferably the left arm). The cu
must be at the level with the heart.

Press the START button.

The average blood pressures and
last data number are displayed
briey. Then the measurement
begins.

Note: If you wish to stop ination at
any time, press the START button
again.

When the measurement is
complete, the systolic and diastolic
pressure readings and pulse rate
are displayed. The cu exhausts
the remaining air and deates
completely.

3

4

5

START button

Averaged data

Data number

Systolic

Diastolic

Pulse

WHO
Classication
Indicator

After the measurement: Press the start button to turn o the device.
The device is provided with an automatic power shut-o function.

5

Measurement with The Desired Systolic Pressure

If your systolic pressure is expected to exceed 230 mmHg, use this procedure.

Sit comfortably in a chair with your
feet at on the oor. Place your left
arm on a table at a slight angle.

Wrap the cu around the upper
arm, about 2 - 3 cm above the
elbow, as shown.

Place the cu directly against
the skin, as clothing may
cause a faint pulse and result
in a measurement error.

Constriction of the upper
arm, caused by rolling up a
shirtsleeve, may prevent
accurate readings.

Conrm that the index
points within the proper t
range.

1

2

Arm Cu

Index Mark and Proper t range

Air Hose

2-3 cm

Place the cu on the arm
(preferably the left arm). The cu
must be at the level with the heart.

3

6