Senao Networks UB9700701 User Manual
IEEE802.b/g/n Wireless LAN
USB 2.0 Client Adapter
User’s Manual
Version: 1.0
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
Table of Contents
1 INTRODUCTION ................................................................................................................5
1.1 F
1.2 P
1.3 USB A
1.4 S
1.5 A
1.6 N
EATURES & BENEFITS
ACKAGE CONTENTS
DAPTER DESCRIPTION
YSTEM REQUIREMENTS
PPLICATIONS
ETWORK CONFIGURATION
..............................................................................................................7
..................................................................................................5
....................................................................................................6
.........................................................................................6
...............................................................................................6
............................................................................................7
2 USB ADAPTER FOR WINDOWS VISTA............................................................................9
2.1 B
2.2 I
2.3 P
2.3.1 I
2.3.2 AD-
2.4 A
EFORE YOU BEGIN
NSTALLING THE DRIVERS
ROFILES
NFRASTRUCTURE MODE
UTHENTICATION AND SECURITY
..................................................................................................................11
HOC MODE
......................................................................................................9
...............................................................................................9
.............................................................................................12
...........................................................................................................13
..................................................................................14
2.4.1 WEP Encryption ...................................................................................................14
2.4.2 WPA, WPA2 Authentication & TKIP, AES Encryption.............................................15
2.4.3 WPA-PSK Authentication & TKIP, AES Encryption ................................................16
2.5 L
2.6 S
2.7 S
INK STATUS
ITE SURVEY
TATISTICS
.................................................................................................................19
..............................................................................................................17
.............................................................................................................18
2.8 WPS.........................................................................................................................20
2.9 A
2.10 U
BOUT
.......................................................................................................................21
NINSTALL THE DRIVERS & CLIENT UTILITY
...................................................................22
3 USB ADAPTER FOR WINDOWS XP................................................................................25
3.1 B
3.2 I
3.3 P
3.3.1 I
3.3.2 AD-
3.4 A
EFORE YOU BEGIN
NSTALLING THE DRIVERS
ROFILES
NFRASTRUCTURE MODE
UTHENTICATION AND SECURITY
..................................................................................................................28
HOC MODE
....................................................................................................25
.............................................................................................25
.............................................................................................28
...........................................................................................................29
..................................................................................30
3.4.1 WEP Encryption ...................................................................................................30
3.4.2 WPA, WPA2 Authentication & TKIP, AES Encryption.............................................31
3.4.3 WPA-PSK Authentication & TKIP, AES Encryption ................................................31
3.4.4 LEAP Authentication.............................................................................................32
3.4.5 802.1x with PEAP.................................................................................................33
3.4.5.1 PEAP Authentication with EAP/TLS Smartcard.................................................33
3.4.6 802.1x with TTLS with EAP-MD5, MS-CHAP, MS-CHAPv2...................................34
3.4.7 802.1x CA Server.................................................................................................35
3.5 N
3.5.1 S
3.6 A
3.7 S
3.8 WMM (W
ETWORK
ITE SURVEY
DVANCED CONFIGURATION
TATISTICS
..................................................................................................................36
.............................................................................................................38
.................................................................................................................39
IRELESS MULTIMEDIA
.........................................................................................39
)...................................................................................41
3.9 WPS.........................................................................................................................41
3.10 A
BOUT
.......................................................................................................................43
2
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
3.11 R
3.12 U
ADIO
.......................................................................................................................43
NINSTALL THE DRIVERS & CLIENT UTILITY
...................................................................44
4 USB ADAPTER FOR MAC OS X......................................................................................47
4.1 I
4.2 P
4.2.1 I
4.2.2 AD-
4.3 A
NSTALLING THE DRIVERS
ROFILES
NFRASTRUCTURE MODE
UTHENTICATION AND SECURITY
..................................................................................................................49
HOC MODE
...........................................................................................................52
.............................................................................................47
.............................................................................................50
..................................................................................53
4.3.1 WEP Encryption ...................................................................................................53
4.3.2 WPA-PSK Authentication & TKIP, AES Encryption ................................................54
4.4 L
4.5 S
4.6 S
4.7 A
4.8 A
INK STATUS
ITE SURVEY
TATISTICS
DVANCED CONFIGURATION
BOUT
..............................................................................................................55
.............................................................................................................56
.................................................................................................................57
.........................................................................................57
.......................................................................................................................59
APPENDIX A – GLOSSARY.....................................................................................................60
APPENDIX B – SPECIFICATIONS ...........................................................................................72
APPENDIX C – FCC INTERFERENCE STATEMENT ...............................................................73
3
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
Revision History
Version Date Notes
1.0 October 17, 2007 Initial Version
4
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
1 Introduction
The high-speed wireless USB 2.0 client adapter is the most convenient way to let
you put a desktop/notebook computer almost anywhere without the hassle of running
network cables. Now you don’t need to suffer from drilling holes and exposed cables.
Once you are connected, you can do anything, just like the wired network. This USB
client adapter operates seamlessly in 2.4GHz frequency spectrum supporting the
802.11b, 802.11g, and 802.11nwireless standards. It’s the best way to add wireless
capability to your existing wired network or simply surf the web.
To protect your wireless connectivity, the high-speed wireless USB 2.0 client adapter
can encrypt all wireless transmissions through 64/128-bit WEP, WPA, WPA-PSK and
WPA-AES encryption and authentication allowing you to experience the most secure
wireless connectivity available.
The Engenius 802.11n USB Adapter (EUB-9702) implements the latest 11n 2.0
technology which extremely improves wireless signal for your computer than existing
wireless 802.11g technology. It supports the
forward compatibility with IEEE802.11n. The incredible speed of EUB-9702 USB
adapter makes heavy traffic networking activities more flexible and takes the wireless
into practical road. You could enjoy the racing speed of wireless connection, surfing
on Internet without string wires.
Adding Engenius EUB-9702 to your Notebook or Computer, it provides an excellent
performance and cost-effective solution for doing media-centric activities such as
streaming video, gaming, and enhances the QoS (WMM) without any reduction of
performance. It extends 3 times network coverage and boosts 6 times transmission
throughput than existing 11g product. Advanced power management and low power
consumption among 11n products.
For more security-sensitive application, EUB-9702 supports Hardware-based IEEE
802.11i encryption/decryption engine, including 64-bit/128-bit WEP, TKIP, and AES.
Also, it supports Wi-Fi alliance WPA and WPA2 encryption and is Cisco CCX V1.0,
V2.0 and V3.0 compliant.
1.1 Features & Benefits
2T2R MIMO architecture with fully
Features Benefits
Racing Speed up to 300Mbps data rate
(2.4GHz 11N technology)
Advanced power management Low power consumption
WPA/WPA2 (IEEE 802.11i), WEP 64/128
Support
5
Enjoy the Internet connection in crazy-fast
speed, without the bottleneck of stringing
wires.
Powerful data security.
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
PWR and LINK
LED Indicator
Support 2Tx * 2Rx Radios With Intelligent Antenna enables
WMM (IEEE 802.11e) standard support Wireless Multimedia Enhancements Quality of
Service support (QoS) / enhanced power
saving for Dynamic Networking
USB 2.0/1.1
USB 2.0 interface and compatible with USB
1.1
1.2 Package Contents
Open the package carefully, and make sure that none of the items listed below are
missing. Do not discard the packing materials, in case of return; the unit must be
shipped in its original package.
One Wireless LAN USB Adapter
One EUB-FLEX USB Cable (15cm)
One CD-ROM with Drivers and User’s Manual Included
One Quick Installation Guide
1.3 USB Adapter Description
The USB adapter is a standard USB adapter that fits into any USB interface. The
USB adapter has two LED indicators and a built-in antenna.
1.4 System Requirements
The following are the minimum system requirements in order to use the USB
adapter.
PC/AT compatible computer with a USB interface.
Windows 2000/XP/Vista or MAC OS operating system.
30 MB of free disk space for installing the USB adapter driver and utility
program.
6
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
1.5 Applications
The wireless LAN products are easy to install and highly efficient. The following list
describes some of the many applications made possible through the power and
flexibility of wireless LANs:
a) Difficult-to-wire environments
There are many situations where wires cannot be laid easily. Historic
buildings, older buildings, open areas and across busy streets make the
installation of LANs either impossible or very expensive.
b) Temporary workgroups
Consider situations in parks, athletic arenas, exhibition centers, disasterrecovery, temporary offices and construction sites where one wants a
temporary WLAN established and removed.
c) The ability to access real-time information
Doctors/nurses, point-of-sale employees, and warehouse workers can
access real-time information while dealing with patients, serving
customers and processing information.
d) Frequently changed environments
Show rooms, meeting rooms, retail stores, and manufacturing sites where
frequently rearrange the workplace.
e) Small Office and Home Office (SOHO) networks
SOHO users need a cost-effective, easy and quick installation of a small
network.
f) Wireless extensions to Ethernet networks
Network managers in dynamic environments can minimize the overhead
caused by moves, extensions to networks, and other changes with
wireless LANs.
g) Wired LAN backup
Network managers implement wireless LANs to provide backup for
mission-critical applications running on wired networks.
h) Training/Educational facilities
Training sites at corporations and students at universities use wireless
connectivity to ease access to information, information exchanges, and
learning.
1.6 Network Configuration
To better understand how the wireless LAN products work together to create a
wireless network, it might be helpful to depict a few of the possible wireless LAN PC
card network configurations. The wireless LAN products can be configured as:
a) Ad-hoc (or peer-to-peer) for departmental or SOHO LANs.
b) Infrastructure for enterprise LANs.
7
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
a) Ad-hoc (peer-to-peer) Mode
This is the simplest network configuration with several computers
equipped with the PC Cards that form a wireless network whenever they
are within range of one another. In ad-hoc mode, each client is peer-topeer, would only have access to the resources of the other client and
does not require an access point. This is the easiest and least expensive
way for the SOHO to set up a wireless network. The image below depicts
a network in ad-hoc mode.
b) Infrastructure Mode
The infrastructure mode requires the use of an Access Point (AP). In this
mode, all wireless communication between two computers has to be via
the AP. It doesn’t matter if the AP is stand-alone or wired to an Ethernet
network. If used in stand-alone, the AP can extend the range of
independent wireless LANs by acting as a repeater, which effectively
doubles the distance between wireless stations. The image below
depicts a network in infrastructure mode.
8
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
2 USB Adapter for Windows Vista
2.1 Before You Begin
During the installation, Vista may need to copy systems files from its installation CD.
Therefore, you may need a copy of the Windows installation CD at hand before
installing the drivers.
2.2 Installing the Drivers
Follow the steps below in order to install the USB adapter drivers:
1. Insert the CD-ROM that was provided to you in this package. The setup
should run automatically. If the setup does not run automatically, then you
must manually select the setup.exe file from the CD-ROM drive.
2. Once the setup begins you will see the InstallShield Wizard. Select
EnGenius Configuration Tool and then click on the Next> button.
9
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
3. Click on the Install button to begin the installation.
4. The installation is complete. Click on the Finish button.
5. Carefully insert the USB adapter into the USB port. Windows will then detect
and install the new hardware.
10
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
6. An EG icon will then appear in the system tray. Right click on the EG icon and
then click on Launch Config Utilities.
Note: Click on Use Zero Configuration as Configuration Utility if you would
like to use Windows Zero Config.
2.3 Profiles
The Profile tab is used to store the settings of multiple Access Points such as
home, office, café, etc. When adding a profile you are required to enter a profile
name and SSID as well as configure the power-saving mode, network type,
RTS/fragmentation threshold and encryption/authentication settings. A profile
can be configured as Infrastructure or Ad-hoc mode. The configuration settings
for each mode are described below.
11
IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
2.3.1 Infrastructure Mode
The infrastructure mode requires the use of an Ac cess Point (AP). In this mode,
all wireless communication between two computers has to be via the AP. It
doesn’t matter if the AP is stand-alone or wired to an Ethernet ne twork. If used in
stand-alone, the AP can extend the range of independent wireless LANs by
acting as a repeater, which effectively doubles the distance between wireless
stations.
h Profile: Enter a name for the prof ile; this does not need to be the same
as the SSID.
h SSID: Enter the SSID of the network or select one from the drop-do wn
list. The SSID is a unique name shared among all points in your wireless
network. The SSID must be identical for all points in the network, and is
case-sensitive.
h Network Type: Select Infrastructure from the drop-down list.
h Click on the Apply button to save the changes.
12
IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
2.3.2 Ad-hoc Mode
This is the simplest network configuration w ith several computers equipped with
the PC Cards that form a wireless network whenever they are within range of one
another. In ad-hoc mode, each client is peer-to-peer, would only have access to
the resources of the other client and does not re quire an ac c ess point. T his is the
easiest and least expensive way for the SOHO to set up a wireless network.
h Profile: Enter a name for the prof ile; this does not need to be the same
as the SSID.
h SSID: Enter the SSID of the net work or select one from the drop-do wn
list. The SSID is a unique name shared among all points in your wireless
network. The SSID must be identical for all points in the network, and is
case-sensitive.
h Network Type: Select Ad-hoc from the drop-down list.
h Click on the Apply button to save the changes.
13
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
2.4 Authentication and Security
The Security tab allows you to configure the authentication and encryption
settings such as: WEP, WPA, WPA-PSK. Each security option is described in
detail below.
2.4.1 WEP Encryption
The WEP tab displays the WEP settings. Encryption is designed to make the
data transmission more secure. You may select 64 or 128-bit WEP (Wired
Equivalent Privacy) key to encrypt data (Default setting is Disable). WEP
encrypts each frame transmitted from the radio using one of the Keys from a
panel. When you use WEP to communicate with the other wireless clients, all the
wireless devices in this network must have the same encryption key or pass
phrase. The following information is included in this tab, as the image depicts
below.
Authentication Type: Select Open or Shared from the drop-down list.
Encryption: Select WEP from the drop-down list.
WEP Key: Type a character string into the field. For 64-bit enter 5
alphanumeric or 10 hexadecimal characters. For 128-bit enter 13
alphanumeric or 26 hexadecimal characters.
14
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
Click on the Apply button to save the changes.
Show Password check box. If you want to make sure the accuracy of
password you type, click the Show Password box to check it.
2.4.2 WPA, WPA2 Authentication & TKIP, AES Encryption
WPA (Wi-Fi Protected Access) was designed to improve upon the security
features of WEP (Wired Equivalent Privacy). The technology is designed to work
with existing Wi-Fi products that have been enabled with WEP. WPA provides
improved data encryption through the Temporal Integrity Protocol (TKIP), which
scrambles the keys using a hashing algorithm and by adding an integritychecking feature which makes sure that keys haven’t been tampered with. EAP
(Extensible Authentication Protocol) is an extension to the PPP protocol that
enables a variety of authentication protocols to be used. It passes through the
exchange of authentication messages, allowing the authentication software
stored in a server to interact with its counterpart in the client.
Authentication Type: Select WPA or WPA2 from the drop-down list.
Encryption: Select TKIP or AES from the drop-down list.
Click on the Apply button to save the changes.
Show Password check box. If you want to make sure the accuracy of
password you type, click the Show Password box to check it.
15
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
2.4.3 WPA-PSK Authentication & TKIP, AES Encryption
WPA – PSK (Pre-shared Key) is used in a Pre Shared Key mode that does not
require an authentication server. Access to the Internet and the rest of the
wireless network services is allowed only if the pre-shared key of the computer
matches that of the Access Point. This approach offers the simplicity of the WEP
key, but uses stronger TKIP encryption. EAP (Extensible Authentication Protocol)
is an extension to the PPP protocol that enables a variety of authentication
protocols to be used. It passes through the exchange of authentication messages,
allowing the authentication software stored in a server to interact with its
counterpart in the client.
Authentication Type: Select WPA or WPA2 from the drop-down list.
Encryption: Select TKIP or AES from the drop-down list.
WPA Preshared key: Enter a pass phrase which is between 8 and 32
characters long.
Click on the Apply button to save the changes.
Show Password check box. If you want to make sure the accuracy of
password you type, click the Show Password box to check it.
16
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
2.5 Link Status
The Link Status tab displays the current status of the wireless radio. The
following information is included in this tab, as the image depicts below.
Status: This indicates the state of the client. There are three options:
o Associated: Indicates that the wireless client is connected to an
Access Point (AP). The BSSID is shown in the form of 12 HEX
digits, which is the MAC address of the AP.
o Scanning: Indicates that the wireless client is searching for an AP
in the area.
o Disconnected: Indicates that there are no APs or clients in the
area.
Extra Info: Displayed here are information about the link stats and the
percent of output power.
Current Channel: The operating frequency channel that the client is
using (infrastructure mode).
Link Speed: The current rate at which the client is transmitting and
receiving.
Throughput (bytes/sec): Displays the Tx (transmit) and Rx (receive)
kilo-bytes per second.
Link Quality: In infrastructure mode, this bar displays the transmission
quality between an AP and a client. In Ad-hoc mode, this bar displays
the transmission quality between one client, and another.
Signal Strength: This bar displays the strength of the signal received
from an AP or client.
Noise Level: Displays the background noise level; a lower level
17
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
indicates less interference.
Click on the OK button to close this window.
dBm Check Box. When you click on the check box as the drawing
below. The signal strength and noise level will be shown as the dBm
measurements.
2.6 Site Survey
The Site Survey tab displays a list of Access Points and Stations in the area, and
allows you to connect to a specific one. The following information is included in
this tab, as the image depicts below.
SSID: Displays the SSID of the Access Point. The SSID is a unique
name shared among all points in your wireless network. The SSID must
be identical for all points in the network, and is case-sensitive.
BSSID: Displays the MAC address of the Access Point.
Signal: Displays the receiving signal strength from the Access Point.
Channel: Displays the channel number of the Access Point.
Encryption: Displays the encryption on the Access Point, this includes
WEP, TKIP, AES or None.
Authentication: displays the authentication on the Access Point, this
includes WPA, WPA-PSK, WPA2, or Unknown.
Network Type: Indicates whether the SSID is a Station (Ad-hoc) or
Access Point (Infrastructure).
Rescan: Click on this button to view a list of Access Points in the area.
18
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
Connect: to connect with a specific Access Point, select the SSID from
the list, and then click on the Connect button.
Add to Profile: Click on this button to add the SSID and its associated
settings into a profile.
Click on the OK button if you have made any changes.
2.7 Statistics
The Statistics tab displays transmit and receive packet statistics in real-time.
Information included is frames transmitted/received successfully, transmitted
successfully without and after retry, received with CRC error, duplicate frames
received, etc.
19
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
2.8 WPS
Click on the WPS Configuration tab. WPS (Wireless Push Button) is used for
WiFi Protected Setup. By pressing this button, the security settings of the device
will automatically synchronize with other wireless devices on your network that
support Wi-Fi Protected Setup.
Rescan: Click on this button to view a list of Access Points in the area.
Click on the OK button if you have made any changes.
20
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
2.9 About
The About tab displays information about the device, such as: the network driver
version and date, configuration utility version and date, and the NIC (Network
Interface Card) firmware version and date.
21
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
2.10 Uninstall the Drivers & Client Utility
If the USB client adapter installation is unsuccessful for any reason, the best way
to solve the problem may be to completely uninstall the USB adapter and its
utility and repeat the installation procedure again.
Follow the steps below in order to uninstall the client utility:
1. Click on Start > EnGenius Wireless > Uninstall EnGenius Wireless USB
Adapter
2. The un-installation process will then begin.
22
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
3. Select the Remove all button and then click on the Next button.
4. Click on the Yes button to confirm the un-installation process.
23
EUB-9701/9702 series --IEEE802.11b/g/n Wireless LAN USB 2.0 Client Adapter Version 1.0
5. The un-installation process is complete. Select Yes, I want to restart my
computer now radio button and then click on the Finish button. Then remove
the USB adapter.
24
Loading...