LAN .................................................................................................................................................................18
ESR7750 is a Dual Band Concurrent
Wireless 11N Broadband Router with dual
CPU that offers user unprecedented network
performance. WMM support boosts streaming
and multimedia intensive services. It supports
2.4Ghz band under 802.11 b/g/n mode while
providing 5Ghz band to guarantee an
interference-free network access.
Multiple SSID provides advance users to manage multiple users of various needs.
TX power control enables flexible transmission tuning for different installation needs and
prevents malicious eaves-dropping. Isolation, filter, firewall and full coverage of security
standards promise a securer network environment.
Dual CPU operates work simultaneously therefore users can enjoy gaming, music
or HD video on 5GHz band while web-surfing or emailing on 2.4Ghz. It also provides with
built-in 4-port full-duplex 10/100 Fast Switch that allows wired ethernet for standard PC
and other network devices. ESR7750 is definitely the optimal choice for both SOHO and
small business entities.
2
1.2. Key Features
Features Advantages
2.4Ghz & 5GhzDual Band Concurrent
Incredible Data Rate up to 600Mbps**
Multiple SSIDs
Four 10/100/1000 Mbps Fast Switch
Ports (Auto-Crossover)
Firewall supports Virtual Server
Mapping, DMZ, IP Filter, ICMP
Blocking, SPI
Support 802.1x Authenticator, 802.11i
(WPA/WPA2, AES), VPN pass-through
WDS (Wireless Distribution System)
Less interference and better
performance
Heavy data payloads such as
MPEG video streaming
Enhanced management among
multiple users groups
Scalability, extend your network.
Avoids the attacks of Hackers or
Viruses from Internet
Provide mutual authentication
(Client and dynamic encryption
keys to enhance security
Make wireless AP and Bridge mode
simultaneously as a wireless
repeater
WPS button support
WMM & QoS
** Theoretical wireless signal rate based on IEEE standard of 802.11a, b, g, n chipset used. Actual throughput
may vary. Network conditions and environmental factors lower actual throughput rate. All specifications are
subject to change without notice.
Quick WiFi Security Setup
Wireless QoS mechanism
3
1.3. Package Contents
Open the package carefully, and make sure that none of the items listed below are
missing. Do not discard the packing materials, in case of return; the unit must be shipped
back in its original package.
1 * Dual Band Concurrent AP Router (ESR7750)
1 * 12V/1.25 A Power Adapter
1 * CAT 5 UTP cable
1 * QIG
1 * CD (User Manual & Wizard)
4
1.4. Product Layout
Physical Interface WAN: 1 * 10/100 Fast Ethernet RJ-45
LAN: 4 * 10/100 Fast Ethernet RJ-45
Reset Button (5 second for reboot, 5~10 seconds for
reset to factory default )
Power Jack
WPS push button (Wi-Fi Protected Setup)
To begin using the ESR7750, make sure you meet the following as minimum
requirements:
PC/Notebook.
Operating System – Microsoft Windows 98SE/ME/XP/2000/VISTA
1 Free Ethernet port.
WiFi card/USB dongle (802.11 a/b/g/n) – optional.
External xDSL (ADSL) or Cable modem with an Ethernet port (RJ-45).
PC with a Web-Browser (Internet Explorer, Safari, Firefox, Opera etc.)
Few Ethernet compatible CAT5 cables.
6
2.2. ESR7750 Placement
You can place ESR7750 on a desk or other flat surface, or you can mount it on a wall. For
optimal performance, place your device in the center of your office (or your home) in a
location that is away from any potential source of interference, such as a metal wall or
microwave oven.
This location must be close to a power connection and your ADSL/Cable modem. If the
antennas are not positioned correctly, performance loss can occur.
7
2.3. Setup LAN & WAN
LAN connection:
Connect Ethernet cable between your PC/Notebook LAN port & one of
the 4 available LAN ports on ESR7750.
WAN connection:
Connect Ethernet cable between WAN ports of your ADSL/CABLE
modem & INTERNET port of ESR7750. Make sure your ADSL/CABLE
modem is working well. Contact your ISP if you have any questions.
select both [Obtain an IP address automatically] and [Obtain DNS server address
automatically].
10
2.5. Smart Wizard CD
Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet.
Then, the router automatically enters the self-test phase. During self-test phase, Power LED
will blink briefly, and then will be lit continuously to indicate that this product is in normal
operation.
Minimum Requirements
• A standard CD-ROM drive
• ADSL or cable modem should be ready for Internet connection.
• Modem must provide RJ45 port to connect with ESR7750.
• Microsoft Windows compatible PC/Notebook with UPnP enabled network adapter
• CAT 5 network cable(s), RJ45 port on PC/Notebook.
STEP 1
Power upthe device.
STEP 2
STEP 3
Wait for POWER led on front panel lights up & remains stable.
Insert Wizard CD into your CD-ROM drive and browse it with Windows Explorer.
Click on “Wizard.exe” to activate SMART WIZARD.
Click on [Setup Wizard] and follow the instruction given on the screen to complete the
initial device configuration.
11
12
2.6. Wizard Configuration
Click <Next> to enter mode selection.
Select the mode that ESR7750 is going to be and set its configurations. AP Repeater mode does not enable WAN interface, Setup Wizard will skip WAN Configuration.
Click <Next> to automatically detect your Internet Network settings.
Smart Wizard has detected DHCP client. Configure the host name and MAC address of your
ADSL modem. Click Next to proceed.
13
Smart Wizard has finished setting up WAN Configuration. Click <Next> to proceed.
Enter the name for your wireless network (SSID) and security key
Click <Next> to proceed
NOTE:
To apply the entire configuration, click <Reboot>.
After Wireless settings are applied, you need to connect from your WLAN client
with the security settings you just finished configuring. Remember the type of
security & security key.
14
2.7. Initial Setup ESR7750
ESR7750 provides web-interface for configuration through web browser, such as
Internet Explorer, Firefox or Safari.
1. Open your browser (e.g. Internet Explorer).
2. Type in http://192.168.0.1 in the address bar and press [Enter].
3. Click <OK> to navigate into ESR7750 configuration home page.
4. You will see the home page of ESR7750 as follows.
15
16
3. SYSTEM
3.1. Status
This page allows you to monitor the current status of your router. You can use the status
page to quickly see if you have any updated firmware available (bug fixes, updates). You can
navigate from this page with a few interesting options for reminding or skipping this page
forever & so forth.
Once you click on <OK> button to go to the requested page, you can see the status page of
the ESR7750.
System: You can see the UP time, hardware information, serial number as well as firmware
version information.
WAN Settings: This section displays whether the WAN port is connected to a Cable/DSL
connection. It also displays the router’s WAN IP address, Subnet Mask, and ISP
Gateway as well as MAC address, the Primary DNS. Press <Renew> button to renew
your WAN IP address.
LAN Settings: This section displays the Broadband router LAN port’s current LAN & WLAN
information. It also shows whether the DHCP Server function is enabled / disabled.
17
WLAN Settings: This section displays the current WLAN configuration settings you’ve
configured in the Wizard / Basic Settings / Wireless Settings section. Wireless
configuration details such as SSID, Security settings, BSSID, Channel number, mode of
operation are briefly shown.
18
3.2. LAN
The LAN Tabs reveals LAN settings which can be altered at will. If you are an entry level
user, try accessing a website from your browser. If you can access website without a glitch,
just do not change any of these settings.
Click <Apply> at the bottom of this screen to save the changed configurations.
LAN IP
IP address: 192.168.0.1. It is the router’s LAN IP address (Your LAN clients default gateway
IP address). It can be changed based on your own choice.
IP Subnet Mask: 255.255.255.0 Specify a Subnet Mask for your LAN segment.
802.1d Spanning Tree: This is disabled by default. If 802.1d Spanning Tree function is
enabled, this router will use the spanning tree protocol to prevent network loops.
DHCP Server
DHCP Server: This will enable or disable the Dynamic Pool setting..
Lease time: This is the lease time of each assigned IP address.
Start IP: This will be the beginning of the pool of IP addresses available for client devices.
End IP: This will be the end of the pool of IP addresses available for client devices.
Domain name: The Domain Name for the existing or customized network.
Loading...
+ 51 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.