Senao Networks PCE3300AN User Manual

PRODUCT DESCRIPTION

The PCE3300AN is a 2.4/5G dual band concurrent 3T3R PCIe module base on AR9590
commercial grade solution.

PRODUCT SPECIFICATION

RF Specification

Radio 0

Frequency Band

Data rate 450 Mbps per radio

Receive Sensitivity (Typical)

(Combined)

Radio 1

Frequency Band

Data rate 450 Mbps per radio

Receive Sensitivity (Typical)

Support 2.4GHz

802.11b/g/n

U.S., Europe and Japan product covering 2.400 to 2.484 GHz

802.11n (2.4GHz_HT20)

-90dBm @ MCS0/8/16

-73dBm @ MCS7/15/23

802.11g

-92dBm @ 6Mbps

-76dBm @ 54Mbps

Support 5GHz

802.11a/n

5.150 - 5.250 GHz, 5.725 - 5.850 GHz

802.11n (5GHz_HT20)

-88dBm @ MCS0/8/16

802.11n (2.4GHz_HT40)

-88dBm @ MCS0/8/16

-70dBm @ MCS7/15/23

802.11b

-93dBm @ 1Mbps

-90dBm @ 11Mbps

802.11n (5GHz_HT40)

-86dBm @ MCS0/8/16

-76dBm @ MCS7/15/23

802.11a

-90dBm @ 6Mbps

-77dBm @ 54Mbps

-72dBm @ MCS7/15/23

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.

For operation within 5.15 ~ 5.25GHz / 5.47 ~5.725GHz frequency range, it is restricted to
indoor environment. The band from 5600-5650MHz will be disabled by the software during
the manufacturing and cannot be changed by the end user. This device meets all the other
requirements specified in Part 15E, Section 15.407 of the FCC Rules.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.

This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and

2) The transmitter module may not be co-located with any other transmitter or
antenna.

As long as 2 conditions above are met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain
laptop configurations or co-location with another transmitter), then the FCC authorization is
no longer considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final end
product must be labeled in a visible area with the following: “Contains FCC ID:
U2M-PCE3300AN”. The grantee's FCC ID can be used only when all FCC compliance
requirements are met.

Industry Canada statement:

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.