Senao Networks PCE3203AH User Manual
802.11 b/g/n 3T3R PCIe Module
PCE3203AH
User’s Manual
- 1 -
PRODUCT DESCRIPTION
General information
Chipset
Atheros AR9381
PA
SiGE SE2565T
Interface
PCI-e
Operating voltage
PCI-e Slot : DC 3.3 V ± 5%
Antenna connectors
3x I-PEX connectors
PCB Dimensions
30 x 60mm (W x L)
Temperature range
0°C to + 60 °C (Operating temperature)
-45°C to + 85°C (Storage temperature)
Security
WPA, WPA2, 64/128 bit WEP, TKIP, and AES. hardware-based IEEE 802.11i encryption engine
Data rates
802.11b:1, 2, 5.5, 11Mbps
802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps
802.11n: 20MHz channel:
1Nss: 65Mbps @ 800ns GI; 72.2Mbps @ 400ns GI (Max);
2Nss: 130Mbps @ 800ns GI; 144.44Mbps @ 400ns GI (Max);
3Nss: 195Mbps @ 800ns GI; 216.7Mbps @ 400ns GI (Max);
802.11n: 40MHz channel:
1Nss: 135Mbps @ 800ns GI; 150Mbps @ 400ns GI (Max.);
2Nss: 270Mbps @ 800ns GI; 300Mbps @ 400ns GI (Max.);
3Nss: 405Mbps @ 800ns GI; 450Mbps @ 400ns GI (Max.);
Tx channel width support
20MHz / 40MHz
Standard/Compliance
WECA (Wi-Fi & Wi-Fi5 compliance), IEEE802.11,b/g/n, RoHS and WEEE
Regulation Certifications
FCC Part 15
Type
Connector
2400~2484.5MHz
PCB Dipole
UFL #0
2.1859 dBi
PCB Dipole
UFL #1
3.3341 dBi
PCB Dipole
UFL #2
4.2057 dBi
PCE3203AH is a 2.4Ghz 3T3R 802.11b/g/n PCIe module base on AR9381 commercial
grade solution.
SPECIFICATIONS
Note: The EUT has three 2.4Ghz antennas. (3TX/3RX)
Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.
- 1 -
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
IMPORTANT NOTE:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
For product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter other than
that specified below:
- 1 -
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna,
As long as 2 conditions above are met, further transmitter tests will not be required.
However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required
with this module installed.
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with
another transmitter not specified), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the
final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the
transmitter) and obtaining a separate FCC authorization.
USERS MANUAL OF THE END PRODUCT:
In the user’s manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while
this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for
an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not
expressly approved by the manufacturer could void the user's authority to operate this equipment.
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in
the user’s manual of the end product which integrates this module.
If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the
user’s manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept any interference received, including interference that may
cause undesired operation.
- 2 -
Loading...