English
Schuberth SC1
www.schuberth.com User’s Guide
SC1
© 1998-2016 Sena Technologies, Inc. All rights reserved.
Sena Technologies, Inc reserves the right to make any changes and improvements to its product without providing prior notice.
Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. Prism™, Bluetooth Audio Pack for GoPro® ,
Tufftalk™, 20S™, 10S™, 10C™, 10U™, 10R™, 3S™, SMH10™, SMH10R™, SMH5™, SMH5-FM™, SMH3™, SPH10™, SPH10H™, SPH10H-FM™,
SPH10S™, Expand™, Bluetooth Mic&Intercom™, Handlebar Remote™, Wristband Remote™, SM10™, SR10™, SR10i™ are trademarks of Sena
Technologies, Inc. or its subsidiaries. These trademarks may not be used without the express permission of Sena.
GoPro® is a registered trademark of Woodman Labs of San Mateo, California. Sena Technologies, Inc. (“Sena”) is not affiliated with Woodman
Labs. The Sena Bluetooth Pack for GoPro® is an after-market accessory specially designed and manufactured by Sena Technologies,
Inc. for the GoPro® Hero3 and Hero4 allowing for Bluetooth capabilities.
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license. iPhone, iPod
touch are registered trademarks of Apple Inc. Zumo™ is a trademark of Garmin Ltd. or its subsidiaries. TomTom™ is the trademark or
registered trademark owned by TomTom International B.V. Other trademarks and tradenames are those of their respective owners.
SC1
CONTENTS
1
INTRODUCTION........................................................................................................
5 2 PACKAGE CONTENTS.............................................................................................
6
3
INSTALLING THE SC1 ON YOUR HELMET............................................................
7
3.1
Installing the SC1.....................................................................................................................
8
3.2
Taking out the SC1...................................................................................................................
8
4
GETTING STARTED.................................................................................................
9
4.1
Button Operation......................................................................................................................
9 4.2
Powering On and Off...............................................................................................................
9
4.3
Charging..................................................................................................................................
9
4.4
Checking the Battery Level...................................................................................................
10 4.5
Volume Adjustment................................................................................................................
10
4.6
Sena Softwares......................................................................................................................
11
5
PAIRING THE SC1 WITH BLUETOOTH DEVICES..............................................
11
5.1
Mobile Phone Pairing - Mobile Phone, Bluetooth Stereo Device..........................................
12
5.2
Second Mobile Phone Pairing - Second Mobile Phone, GPS, and SR10............................
12 5.3
Advanced Selective Pairing - A2DP Stereo or Handsfree....................................................
13
6
MOBILE PHONE, GPS, SR10................................................................................
14
6.1
Mobile Phone Call Making and Answering...........................................................................
14
6.2
Speed Dialing........................................................................................................................
15
6.3
GPS Navigation......................................................................................................................
16
6.4
Sena SR10, Two-Way Radio Adapter....................................................................................
16
7
STEREO MUSIC.....................................................................................................
16
8
INTERCOM.............................................................................................................
17
8.1
Intercom Pairing.....................................................................................................................
18 8.2
Two-way Intercom..................................................................................................................
19
8.3
Three-way Intercom...............................................................................................................
20
8.4
Four-way Intercom.................................................................................................................
21 8.5
Team Signal...........................................................................................................................
22
9
THREE-WAY CONFERENCE
........................................................................................................
PHONECALLWITHINTERCOM
22 PARTICIPANT
10
GROUP INTERCOM...............................................................................................
23
11
UNIVERSAL INTERCOM.......................................................................................
24
11.1
Universal Intercom Pairing....................................................................................................
25
11.2
Two-way Universal Intercom..................................................................................................
25 11.3
Three-way Universal Intercom...............................................................................................
26
11.4
Four-way Universal Intercom.................................................................................................
27
12
FM RADIO...............................................................................................................
29
12.1
FM Radio On and Off.............................................................................................................
29
12.2
Preset Stations.......................................................................................................................
29
12.3
Region Selection....................................................................................................................
30
13
FUNCTION PRIORITY...........................................................................................
30
English
7.1 Bluetooth Stereo Music ............................................................. 16
7.2 Music Sharing ....................................................................... 17
SC1
14 CONFIGURATION SETTING.................................................................................
31
14.1
Intercom Pairing.....................................................................................................................
32
14.2
Mobile Phone Pairing.............................................................................................................
32
14.3
Second Mobile Phone Pairing...............................................................................................
33
14.4
Phone selective pairing.........................................................................................................
33
14.5
Media Selective Pairing.........................................................................................................
33
14.6
Assigning Speed Dial............................................................................................................
33
14.7
Enabling/Disabling Audio Boost............................................................................................
34
14.8
Enabling/Disabling Voice Activated Phone Answering........................................................
34
14.9
Enabling/Disabling Voice Activated Intercom.......................................................................
35
14.10
Enabling/Disabling HD Intercom.......................................................................................
35
14.11
Enabling/Disabling Voice Prompts....................................................................................
36
14.12
Enabling/Disabling RDS AF...............................................................................................
36
14.13
Enabling/Disabling Advanced Noise Control™ ...............................................................
36
14.14
Delete All Bluetooth Pairing Information............................................................................
36
14.15
Remote Control Pairing......................................................................................................
37
14.16
Universal Intercom Pairing.................................................................................................
37
14.17
Factory Reset.....................................................................................................................
37
14.18
Exit Voice Configuration Menu...........................................................................................
37
15 REMOTE CONTROL..............................................................................................
39
16 FIRMWARE UPGRADE..........................................................................................
39
17 TROUBLESHOOTING............................................................................................
40
17.1
Intercom Failure.....................................................................................................................
40
17.2
Intercom Reconnection.........................................................................................................
40
17.3
Factory Reset.........................................................................................................................
40
18 QUICK OPERATION REFERENCE.......................................................................
41
CERTIFICATION AND SAFETY APPROVALS ...................................... 42
• FCC Compliance Statement ........................................................... 42
• FCC RF Exposure Statement .......................................................... 43
• FCC Caution ................................ ........................................... 43
• CE Declaration of Conformity .......................................................... 43
• Industry Canada Statement ............................................................ 43
• Bluetooth License ...................................................................... 44
• WEEE (Waste Electrical and Electronic Equipment) ................................... 44
SAFETY INFORMATION ................................................................ 44
• Product Storage and Management ..................................................... 44
• Product Use ............................................................................ 45
• Battery ................................................................................. 45
PRODUCT WARRANTY AND DISCLAIMER ........................................ 46
• Limited Warranty ....................................................................... 46
• Warranty Exclusions ................................................................... 48
• Warranty Service ....................................................................... 50
SC1
The SC1 features:
1 INTRODUCTION
• Bluetooth 4.1
• Invisible beauty with custom design
Thank you for choosing the Schuberth SC1. With the SC1, you can call
• Bluetooth intercom up to 1.6 kilometer (1.0 miles)*
handsfree on your Bluetooth mobile phone, listen to stereo music or
• Four-way intercom
voice instructions of GPS navigations wirelessly, and have intercom
• Voice prompts
conversations in full duplex with a passenger or other motorcycle
• Smartphone App for iPhone and Android
riders.
• Built-in FM radio tuner with a station scan and save function
The SC1 is compliant with the Bluetooth 4.1 supporting the following
• Universal Intercom™
profiles: Headset Profile, Hands-Free Profile (HFP), Advanced Audio
• Music sharing
Distribution Profile (A2DP), and Audio Video Remote Control Profile
• Advanced Noise Control™
(AVRCP). Please check with the manufacturers of other device to
• Firmware upgradeable
determine their compatibility with this headset.
Please read this User’s Guide carefully before using the headset. Also
* in open terrain
check
www.schuberth.com
for the latest version of the User’s Guide
and additional information related to Sena Bluetooth products.
English
5
SC1
Key Specifications:
• Bluetooth 4.1
• Supporting profiles: Headset Profile, Hands-Free Profile (HFP),
Advanced Audio Distribution Profile (A2DP), and Audio Video
Remote Control Profile (AVRCP).
2 PACKAGE CONTENTS
• SC1 Main Unit
6
• Battery
• Release Tool
SC1
3 INSTALLING THE SC1 ON YOUR HELMET
LED
(+) Button
(-) Button
DC Power Charging &
Firmware Upgrade Port
English
7
SC1
3.1 Installing the SC1
1. Insert the main unit into the helmet and push it gently until you
hear a click.
Click
2. Insert the battery into the helmet and push it gently until it is
all the way in.
8
3.2 Taking out the SC1
1. Insert the release tool into the main unit and push it gently
until you hear a click.
Click
2. Pull the release tool until the main unit comes off the helmet.
SC1
4 GETTING STARTED
4.1 Button Operation
(+) Button
(–) Button
4.2 Powering On and Off
To power on the headset, press and hold the (+) Button and the (-)
Button at the same time for 1 second while hearing ascending beeps
and a voice prompt, “Hello”. To power off the headset, press and
hold the (+) Button and the (-) Button at the same time for 3 seconds
while hearing descending beeps and a voice prompt, “Goodbye”.
4.3 Charging
You can charge the headset by connecting the supplied USB power &
English
data cable into a computer’s USB port or USB wall charger. You can
use any standard micro USB cable to charge the unit. The LED turns
red while charging and turns blue when fully charged. It takes about
2.5 hours to be completely charged.
AC Adapter
or
Note:
Please make sure to take off your SC1-installed helmet while charging.
The headset automatically turns off during charging.
9
SC1
4.4 Checking the Battery Level
4.4.1 LED Indicator
When the headset is powering on, the red LED flashes rapidly
indicating the battery level.
4 flashes = High, 70 ~ 100%
3 flashes = Medium, 30 ~ 70%
2 flashes = Low, 0 ~ 30%
4.4.2 Voice Prompt Indicator
When you power on the headset, keep pressing the (+) Button
and the (-) Button simultaneously for about 3 seconds until you
hear three, high toned beeps. Then you will hear a voice prompt
indicating the battery level. However, if you release the buttons
as soon as the headset turns on, you will not hear a voice prompt
for the battery level indication.
4.5 Volume Adjustment
You can easily adjust the volume by tapping the (+) Button or the (-)
Button. You will hear a beep when the volume reaches the maximum
or minimum level. The volume is set and maintained independently at
different levels for each audio source even when you reboot the
headset. For example, once you set the volume for mobile phone
handsfree, it will not change even if you adjust the volume for your
Bluetooth MP3 music. However, if you adjust the volume during
stand-by mode, it will affect volume levels of every audio source.
10
SC1
4.6 Sena Softwares
4.6.1 Sena Device Manager
The Sena Device Manager allows you to upgrade the firmware
and configure the device settings directly from your PC. Using
this software, you can assign speed dial presets, FM radio
frequency presets and more. It is available for both Windows and
Mac. For more information on downloading the Device Manager,
please visit oemsena.com/oem-schuberth/.
4.6.2 Sena Smartphone App
The Sena Smartphone App allows you to configure device settings and
read the User’s Guide and the Quick Start Guide. Pair your phone with
your SC1 headset (please refer to section 5.1, “Mobile Phone Pairing -
Mobile Phone, Bluetooth Stereo Device”). Run the Sena
Smartphone App and you can configure its settings directly from
your smartphone. You can download the Sena Smartphone App
for Android or iPhone from www.sena.com/headset-app.
5 PAIRING THE SC1 WITH BLUETOOTH
E
n
g
li
s
h
DEVICES
Before using the SC1 Bluetooth headset with any other Bluetooth devices
for the first time, you will need to pair them together. You can pair the
SC1 with Bluetooth mobile phones, Bluetooth stereo devices such as
MP3 players, or motorcycle specific Bluetooth GPS navigation, and with
other Sena Bluetooth headsets. The pairing operation is required only
once for each Bluetooth device. The headset remains paired with the
devices and automatically reconnects to them when they are within range.
You will hear a high toned single beep and a voice prompt whenever the
headset reconnects to the paired device:
“Phone connected” to a mobile phone, “Media connected” to
a Bluetooth stereo device.
11
SC1
5.1 Mobile Phone Pairing - Mobile Phone,
Bluetooth Stereo Device
1. Press and hold the (+) Button or the (-) Button for 10 seconds
until you hear the voice prompt, “Configuration menu”.
2. Tap the (+) Button until you hear a voice prompt, “Phone pairing”.
3. Search for Bluetooth devices on your mobile phone. Select the
SC1 in the list of the devices detected on the mobile phone.
4. Enter 0000 for the PIN. Some mobile phones may not ask for
the PIN.
5. The mobile phone confirms that pairing has completed and the
SC1 is ready to use. You will hear a voice prompt, “Your
headset is paired”.
6. If the pairing process is not completed within three minutes,
the SC1 will return to stand-by mode.
Note:
1. If a Bluetooth connection between the headset and a mobile phone is
disconnected, press the (+) Button for 3 seconds until you hear a high
tone single beep to recover the Bluetooth connection immediately.
2. If the Bluetooth connection between the headset and a media player is
disconnected, press the (+) Button for 1 second to recover the Bluetooth
connection and play.
12
5.2 Second Mobile Phone Pairing - Second
Mobile Phone, GPS, and SR10
Typical Bluetooth headsets can connect with only one Bluetooth
device, but a second mobile phone pairing allows the headset to
connect with another Bluetooth device such as a second mobile
phone, an MP3 Player, or the Sena SR10, the Bluetooth adapter.
1. To enter the voice configuration menu, press and hold the (+)
Button or the (-) Button for 10 seconds until you hear the
voice prompt, “Configuration menu”.
2. Tap the (+) Button until you hear a voice prompt, “Second
mobile phone pairing”.
3. Search for Bluetooth devices on your mobile phone. Select the
SC1 in the list of the devices detected on the mobile phone.
4. Enter 0000 for the PIN. Some mobile phones may not ask for
the PIN.
5. The mobile phone confirms that the pairing has completed
and the SC1 is ready to use. You will hear a voice prompt,
“Your headset is paired”.
SC1
Note:
1. If you have two audio (A2DP) devices connected to your headset then
the audio from one device will interrupt the audio from the other device.
For example, if you are playing music from the primary mobile phone,
then it can be interrupted by playing music from the secondary mobile
phone and vice versa.
2. You have to use a motorcycle specific GPS, which transmits turn-byturn voice instructions to the headset by Bluetooth. Most automotive
GPS systems do not have this feature.
3. The Sena SR10 is a Bluetooth two-way radio adapter for group
communication, and uses Hands-Free Profile. The incoming audio from
the two-way radio via SR10 is heard in the background while having an
intercom conversation or a mobile phone call.
4. The GPS navigation or a radar detector could be connected to the SR10 by
wire. The GPS voice instruction or the radar detector alarm is also heard in
the background via SR10 while having an intercom conversation or a phone
call. Please refer to the SR10 User’s Guide for details.
5.3 Advanced Selective Pairing - A2DP
Stereo or Handsfree
When you are using a smartphone, sometimes you may need to
selectively use the SC1 for A2DP stereo music only or for mobile
phone handsfree only. These instructions are for advanced users
who want to pair the SC1 to their smartphones with only one
selective profile: A2DP for stereo music of HFP for phone calls.
If you have previously paired a mobile phone to the SC1, you must
clear the previous pairing list on both devices: the mobile phone and
the SC1. To clear the pairing list on the SC1, please do a factory
reset or following the pairing list clearing procedure described in
section 14.17, “Factory Reset” or 14.14, “Delete All Bluetooth Pairing
Information”. To clear the pairing list on the mobile phone, please
refer to the mobile phone manual. For most smartphones, delete the
SC1 from the list of Bluetooth devices in the settings menu.
English
13
SC1
5.3.1 A2DP Stereo Music Only
1. To enter the voice configuration menu, press and hold the (+)
Button or the (-) Button for 10 seconds until you hear the
voice prompt, “Configuration menu”.
2. Tap the (+) Button until you hear the voice prompt, “Media
selective pairing”.
3. Search for Bluetooth devices on your smartphone. Select the
SC1 in the list of devices detected on your phone.
4. Enter 0000 for the PIN. Some mobile phones may not ask for
the PIN.
5.3.2 HFP for Phone Call Only
1. To enter the voice configuration menu, press and hold the (+)
Button or the (-) Button for 10 seconds until you hear the
voice prompt, “Configuration menu”.
2. Tap the (+) Button until you hear the voice prompt, “Phone
selective pairing”.
3. Search for Bluetooth devices on your smartphone. Select the
SC1 in the list of devices detected on your phone.
4. Enter 0000 for the PIN. Some mobile phones may not ask for
the PIN.
14
6 MOBILE PHONE, GPS, SR10
6.1 Mobile Phone Call Making and Answering
1. When you have an incoming call, tap the (+) Button to answer
the call.
2. You can also answer the incoming call by loudly speaking any
word of your choice if Voice Activated Phone Answering (VOX
Phone) is enabled, unless you are connected to intercom.
3. To end a call, press the (+) Button for 2 seconds until you hear a
mid-tone single beep, or wait for the called person to end the call.
4. To reject a call, press the (+) Button for 2 seconds until you
hear a beep while the phone is ringing.
5. There are several ways to make a phone call:
–– Enter numbers on your mobile phone’s keypad and make a
call. Then the call is automatically transferred to the headset.
–– In stand-by mode, press the (+) Button for 3 seconds, to
activate the voice dialing of your mobile phone. For this, the
voice dialing function must be available on the mobile phone.
Refer to your mobile phone manual for further instruction.
SC1
Note:
1. If you have two phones connected to your headset and you have an
incoming call from the second phone during the call of the first phone,
then you may still receive the call from the second phone. In this case,
the call from the first phone is on waiting mode. If you end a call, then it
will automatically guide you to the first phone call.
2. If you have a mobile phone and a GPS connected to your headset, you
may not be able to listen to the GPS voice instruction during the phone
call.
6.2 Speed Dialing
You can quickly make a phone call by using the voice speed dial
menu.
1. To enter into the voice speed dial menu, press and hold the
(+) Button for 5 seconds and you will hear a mid-tone single
beep and a voice prompt saying “Speed dial”.
2. Tap the (+) Button to navigate between the menus. You will
hear voice prompts for each menu item.
3. Tap the (-) Button to select a voice menu among the followings:
(1)
Last number redial
(4)
Speed dial 3
(2)
Speed dial 1
(5)
Cancel
(3)
Speed dial 2
4. After selecting the last number redial menu, you will hear a
voice prompt, “Last number redial”. Then, to redial the last
phone call number, tap the (-) Button.
5. To call one of the speed dials, tap the (+) Button to navigate
between the menus until you hear a voice prompt saying
“Speed dial (#)”. Then, tap the (-) Button.
6. If you want to exit the speed dial immediately, tap the (+) Button
until you hear a voice prompt saying “Cancel”, and tap the (-)
Button. If you do not press any button within 15 seconds, the SC1
will exit the voice speed dial menu and go back to stand-by mode.
Note:
1. Make sure that you connect the mobile phone and the headset to use
the speed dial function.
2. You need to assign speed dial numbers before using the speed dial
(please refer to section 14.6, “Assigning Speed Dial”).
English
15
SC1
6.3 GPS Navigation
If you pair a Bluetooth GPS to the SC1 as described in section
5.2, “Second Mobile Phone Pairing - Second Mobile Phone, GPS,
and SR10” , you can listen to GPS instructions wirelessly. Tap
the (+) Button or the (-) Button to adjust volume. The GPS voice
instruction interrupts intercom conversation but it is automatically
reestablished after the GPS voice instruction ends.
6.4 Sena SR10, Two-Way Radio Adapter
You can use a two-way radio and the SC1 Bluetooth intercom
simultaneously by using the Sena SR10, a Bluetooth Two-way Radio
Adapter (please refer to section 5.2, “Second Mobile Phone Pairing -
Second Mobile Phone, GPS, and SR10”). Incoming audio from the
two-way radio will not interrupt an intercom conversation but is heard
in the background. This is useful when you have an intercom
conversation with a passenger on the back seat and use a two-way
radio for group communication with other motorcycle riders.
7 STEREO MUSIC
7.1 Bluetooth Stereo Music
The Bluetooth audio device must be paired with the SC1 by following the
“Mobile Phone Pairing - Mobile Phone, Bluetooth Stereo Device”
procedures described in the section 5.1. The SC1 supports the Audio/
Video Remote Control Profile (AVRCP), so if your Bluetooth
audio device also supports the AVRCP, you can use the SC1 to
remotely control music playback. Not only can you adjust the
volume but you can also use functions such as play, pause, next
track and previous track.
1. To play or pause music, press the (+) Button for 1 second
until you hear a double beep.
2. To adjust the volume, tap the (+) Button or the (-) Button.
3. To track forward or track back, press and hold the (+) Button or
the (-) Button for 2 seconds until you hear a mid-tone single beep.
16
SC1
7.2 Music Sharing
You can start sharing music with an intercom friend using Bluetooth
stereo music during a two-way intercom conversation (please refer to
section 8.2, “Two- way Intercom”). When you terminate music sharing,
you can go back to the intercom conversation. To start or terminate
sharing music, press the (+) Button for 1 second during an intercom
conversation until you hear a double beep. To track forward or track back,
press and hold the (+) Button or the (-) Button for 2 seconds.
Note:
1. Both you and your intercom friend can remotely control music playback
such as track forward and track back.
2. Music sharing will be paused when you are using your mobile phone or
listening to GPS instructions.
8 INTERCOM
To enter the intercom pairing mode, call intercom friends, or start
group intercom, you must enter the intercom menu by pressing
the (-) Button for 1 second. If you perform any action within the
intercom menu, you will automatically exit from the menu.
Intercom Functions
Button Operation
Enter intercom menu
Press the (-) Button for 1 second
- Enter intercom pairing mode
Tap the (+) Button
- Call first intercom friend
Tap the (-) Button
- Call second intercom friend
Double tap the (-) Button
- Call third intercom friend
Triple tap the (-) Button
- Start Group Intercom
Press the (-) Button for 1 second
- Exit intercom menu
Press the (+) Button for 3 seconds
English
17
SC1
8.1 Intercom Pairing
8.1.1 Pairing with Other SC1 Headsets for
Intercom Conversation
The SC1 can be paired with up to three other headsets for
Bluetooth intercom conversation.
1. Turn on the two SC1 headsets (A and B) that you would like
to pair with each other.
2. Press and hold the (-) Button for 1 second to enter the
intercom menu.
3. Tap the (+) once, and you will hear a mid-tone single beep
and the voice prompt, “Intercom pairing”.
4. Simply tap the (+) Button of any one of the two headsets A or B and
wait until the LEDs of both headsets turn to blue and intercom
connection is automatically established. The two SC1 headsets A and
B are paired with each other for intercom conversation. If the pairing
process is not completed within one minute, the SC1 will
return to stand-by mode.
A
B D
C
Pairing A & B
5. You can make other pairing between headsets A and C, and
between headsets A and D by following the same procedure
as above.
18
Loading...