SEMPELL PRESSURE SEAL CHECK VALVES - STYLE A
INSTALLATION AND MAINTENANCE INSTRUCTIONS
Before installation these instructions must be fully read and understood
1 VALVE STORAGE
1.1 Preparation and preservation for
shipment
All valves are properly packed in order
to protect the parts that are subject to
deterioration during transportation and storage
on site. In particular, the following precautions
should be taken:
1. The weld ends surface shall be protected
with suitable protective like Deoxaluminite.
The end shall be closed with plywood or
plastic disc fixed at the edge by strips.
2. The type of packing must be defined in the
customer’s order and shall be appropriate
to ensure safe transportation to final
destination and eventual conservation
before installation.
1.2 Handling requirements
A - Packed valves
Crates: Lifting and handling of the packed
valves in crates will be carried out
by a fork lift truck, by means of the
appropriate fork hitches.
Cases: The lifting of packed valves in cases
should be carried out in the lifting
points and at the center of gravity
position which have been marked.
The transportation of all packed
material must be carried out safely and
following the local safety regulations.
B - Unpacked valves
1. The lifting and the handling of these valves
has to be carried out by using appropriate
means and at respecting the carrying limits.
The handling must be carried out on pallets,
protecting the machined surfaces to avoid
any damage.
2. With valves of large dimensions, the sling
and the hooking of the load must be carried
out using the appropriate tools (brackets,
hook, fasteners, ropes) and load balancing
tools in order to prevent them from falling
or moving during the lifting and handling.
1.3 Storage and preservation before
installation
In case the valves have to be stored before
installation, the storage has to be carried out
in a controlled way, and has to be performed in
accordance with the following criteria:
1. The valves have to be stocked in a closed,
clean and dry storage room.
2. The disc must be in the closed position,
and the end faces must be protected with
plastic or wooden discs fixed with straps.
If possible, keep the original protection.
3. Periodical checks have to be carried out
in the storage area to verify that the above
mentioned conditions are maintained.
© 2017 Emerson. All Rights Reserved.Emerson.com/FinalControl VCIOM-01853-EN 19/11
SEMPELL PRESSURE SEAL CHECK VALVES - STYLE A
INSTALLATION AND MAINTENANCE INSTRUCTIONS
NOTE
Storage in an open area for a limited period can be
considered only in case the valves have appropriate
packing (packed in cases lined with tarred paper, and
contents well protected with barrier sacks).
Do not place consignment packages directly on the
ground.
Do not expose consignment packages to the weather
or directly to the sun.
Check the packaging every two months.
CAUTION
For valve handling and/or lifting, the lifting
equipment (fasteners, hooks, etc.) must be sized
and selected while taking into account the valve
weight indicated in the packing list and/or delivery
note. Lifting and handling must be made only by
qualified personnel.
Caution must be taken during the handling to
avoid that this equipment passes over the workers
or over any other place where a possible fall
could cause damage. In any case, the local safety
regulations must be respected.
WARNING
For valve handling and/or lifting, the lifting
equipment (fasteners, hooks, etc.) must be sized
and selected while taking into account the valve
weight indicated in the packing list and/or delivery
note. Lifting and handling must be made only by
qualified personnel.
Caution must be taken during the handling
to avoid that this equipment passes over the
workers or over any other place where a possible
fall could cause damage. In any case, the local
safety regulations must be respected.
2 INSTALLATION
2.1 Preparation before installation
1. Carefully remove the valve from the
shipping package (box or pallet) avoiding
any damage to the valve.
2. Clean the inside of the valve using an air
line. Ensure that there are no solid objects
such as pieces of wood, plastic or packing
materials within the valve or on the valve
seat.
3. Confirm that the materials of construction
listed on the valve nameplates (service and
temperature) are appropriate for the service
intended and are as specified.
4. Define the preferred mounting orientation
with respect to the system pressure. The
arrow on the body identifies the upstream
side (high pressure) and downstream side
(low pressure).
WARNING
Verify that the direction of the flow in the line
corresponds to the arrow indicated on the valve
body.
FIGURE 1
Valve slinging
Swing check and
tilting disc valves
FIGURE 2
Installation positions recommended
Flow
0 - 90°
25° max.°
25° max.°
2
SEMPELL PRESSURE SEAL CHECK VALVES - STYLE A
INSTALLATION AND MAINTENANCE INSTRUCTIONS
2.2 Installation instructions
Check valves are normally installed in
horizontal pipe, but can also be installed in
vertical pipe with upward flow.
For a correct operation, Sempell recommends
that the valve shall be installed and oriented
following the indications of Figure 2.
This can help minimize any problem associated
with solid particles present in the fluid that
otherwise could deposit in the lower part of
the body and be obstacle to the disc complete
closure.
Unless otherwise recommended by Sempell,
the valve should be installed with the disc in the
closed position, to ensure that the seat ring in
the disc is not damaged during installation.
For operating temperatures above 200°C
(392°F) thermal insulation of the valve body
is recommended.
Handling and lifting of the valves during
installation MUST be performed following the
same criteria and instructions described in
previous points '1.2 Handling requirements'
and '1.3 Storage and preservation before
installation'.
Buttweld valves
Position the valve and check the alignment
with the pipe, then proceed with welding,
in accordance with the applicable welding
procedure.
IMPORTANT
After the valves installation and before the line
testing, it is recommended to perform an accurate
cleaning of the lines to eliminate dirt and any
foreign objects that could seriously jeopardize
the tightness between seat/disc and the correct
operation of the valve.
2.3 Valve verification before start up
1. If the valve has been stored for a long time,
check the bolt torque for bolting (pos. 31) in
accordance with Table I.
IMPORTANT
If piping system is pressurized with water for
testing, and in case the piping system has been
shut down after testing for a long time, the
following recommendations should be adopted.
a. Use corrosion inhibitor with water to
pressurize the piping system.
b. After testing, the piping system should be
depressurized and the test water completely
drained.
2.4 Operations instructions
1. Style A series check valves do not require
special care to work properly.
The following instructions will help provide
a satisfactory and long life service.
2. Make sure to perform periodic valve
verification as described in paragraph 2.5.
2.5 Periodic valve verification during service
A - Normal check
1. Verify monthly that there is no leakage
from the body/bonnet area. If the leakage
has been detected from the body/bonnet
area, tighten the nuts (pos. 31) as indicated
in Table I. If the leakage does not stop,
follow the maintenance procedure for
the replacement of the body/bonnet
gasket (3.2, 3.3).
B - Preventive actions
1. Every 4 years disassemble the critical
service valves, verifying the sealing surfaces
and lap them again when necessary.
Substitute the bonnet gasket.
IMPORTANT
To ensure tightness of pressure seal gasket, pull
up bolts must be tightened when valve is under
fully hydrostatic test pressure.
TABLE I - POSITION 31 FOR CHECK VALVES
BOLT TORQUE TO ENSURE TIGHTNESS OF
PRESSURE SEAL GASKET
Stud Torque (ft·lbs) Torque (Nm)
⅜ 18 24.5
½ 37 50.0
⅝ 74 100.0
¾ 125 170.0
⅞ 207 280.0
1 310 420.0
1⅛ 443 600.0
1¼ 627 850.0
1⅜ 811 1100.0
TROUBLESHOOTING GUIDE
Symptom Possible cause Solution
Body-bonnet leaking 1. Gasket bolting loose (pos 31) 1. Tighten bolting (pos 31)
2. Gasket damaged 2. Replace gasket
Valve leaking 1. Valve not fully closed 1. Flush valve in order to close it
2. Debris trapped in valve 2. Cycle and flush (with valve open)
toremove debris
3. Sealing surface damaged 3. Recondition the sealing surface
3
42 311 6 31 32
SEMPELL PRESSURE SEAL CHECK VALVES - STYLE A
INSTALLATION AND MAINTENANCE INSTRUCTIONS
3 MAINTENANCE
The Style A series valves have been designed
to require minimum maintenance.
This manual describes on site repairs as:
- Body/bonnet gasket replacement
All the other repairs should be performed by
Sempell or Authorized Service Provider.
3.1 Bonnet gasket replacement
WARNING
Before starting any maintenance, depressurize,
drain and vent the line; check that the valves are
not in temperature.
Failure to do so may cause serious personal
injury and/or equipment damage.
Please refer to Figure 3.
1. Unscrew the nuts (pos.31).
2. Remove the retaining ring (pos.311).
3. Remove the segment rings, push them out
from the body groove by using the body
holes placed radially on the top of the body.
4. Lift up the bonnet (pos.6) and pressure seal
body gasket (pos.5).
5. Carefully clean all the gasket housing and
lubricate with suitable grease.
6. Replace the body gasket.
7. Reassemble all parts following backwards
the above mentioned steps.
CAUTION
The nuts (pos.31) need to be retightened after
valve first pressurization, as indicated in Table I.
4 VALVE REMOVAL
If the valve needs to be removed from the line
for some extraordinary reason, the user should
ensure the following:
1. The valve is depressurized, drained and
vent.
2. The pipe shall be cut as far away from the
valve as possible.
5 SPECIAL TOOLS
No special tool required for the maintenance
operation described in this manual.
FIGURE 3
42 311 6 31 32
43
5
Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product.
Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
Sempell is a mark owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co. Emerson Automation Solutions, Emerson
andthe Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be
construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by
our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such products at any time without
notice.
Emerson.com/FinalControl
4
Loading...