Semelab Plc LT1085-220M, LT1085 Datasheet
Prelim. 10/95
LT1085–220M–05
LT1085–05–220M
LT1085–12–220M
MILITARY VERSION
Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: sales@semelab.co.uk
Website: http://www.semelab.co.uk
Dia.
2.65
2.75
0.89
1.14
0.70
0.90
4.70
5.00
10.41
10.67
3.56
3.81
16.38
16.89
13.39
13.64
10.41
10.92
12.70
19.05
2.54
BSC
123
TO–220 Isolated Metal Package
Pin Fixed Adjustable
1 GROUND ADJUST
2 OUTPUT OUTPUT
3 INPUT INPUT
Case is ISOLATED
LT1085–220M Positive Adjustable Regulator
LT1085–05–220M Fixed +5V Regulator
LT1085–12–220M Fixed +12V Regulator
Pinouts
Ordering Information
ABSOLUTE MAXIMUM RATINGS (T
case
= 25°C unless otherwise stated)
LOW DROPOUT
3 AMP POSITIVE
VOLTAGE REGULATOR
V
IN
Input Voltage 5V, 12V
V
I-O
Input–Output Differential Voltage Adjustable
P
D
Power Dissipation
V
IN
Operating Input Voltage Adjustable
5 Volt
12 Volt
T
J
Operating Junction Temperature Range Control
Power
T
STG
Storage Temperature Range
T
LEAD
Lead Temperature (for 10 sec.)
30V
35V
Internally limited
25V
20V
25V
–55 to 150°C
–55 to 200°C
–65 to 150°C
300°C
FEATURES
• Low Dropout Performance
• Fixed or Adjustable Voltages
• Fixed Output Voltages of 5V & 12V
• Output Current 3A
• Line Regulation 0.015% / V Typical.
• Load Regulation 0.1% Typical.
• Military Temperature Range (–55 to +150°C)
IN
V
THERMAL
LIMIT
ADJ
V
OUT
V
* Although the devices’ maximum operating voltage is limited (20V for the 5V device, and 25V for the 12V and adjustable devices) the devices are
guaranteed to withstand transient input voltages up to 30V. For input voltages greater than the maximum operating input voltage, some degradation of
specifications will occur. For 5V and 12V devices operating at input-output voltage differentials >15V, a minimum external load of 5mA is required to
maintain regulation.
BLOCK DIAGRAM
Prelim. 10/95
LT1085–220M–05
LT1085–05–220M
LT1085–12–220M
MILITARY VERSION
Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: sales@semelab.co.uk
Website: http://www.semelab.co.uk
V
O
Output Voltage
V
REF
Reference Voltage
REG
(LINE)
Line Regulation
REG
(LOAD)
Load Regulation
See notes 1,2
V
D
Dropout Voltage
See note 3
Output
Parameter Voltage Test Conditions Min. Typ. Max. Unit
VIN= 6.5 to 20V IO= 0 to 3A
T
J
= –55 to 150°C
V
IN
= 13.5V to 25V IO= 0 to 3A
T
J
= –55 to 150°C
V
IN
– V
OUT
= 1.5 to 15V IO= 10mA to 3A
T
J
= –55 to 150°C
V
IN
= 6.5 to 20V
I
O
= 0 TJ= –55 to 150°C
V
IN
= 13.5 to 25V
I
O
= 0 TJ= –55 to 150°C
V
IN
– V
OUT
= 1.5 to 15V
I
LOAD
= 10mA TJ= –55 to 150°C
V
IN
= 8V
I
O
= 0 to 3A TJ= –55 to 150°C
V
IN
= 15V
I
O
= 0 to 3A TJ= –55 to 150°C
V
IN
– V
OUT
= 3V
I
O
= 10mA to 3A TJ= –55 to 150°C
D
V
OUT
= 50mV
I
OUT
= 3A TJ= –55 to 150°C
D
V
OUT
= 120mV
I
OUT
= 3A TJ= –55 to 150°C
D
V
REF
= 1%
I
OUT
= 3A TJ= –55 to 150°C
4.90 5 5.10
11.76 12 12.24
1.225 1.25 1.270
0.5 10
110
125
225
0.015 0.2
0.035 0.2
520
10 35
12 36
24 72
0.1 0.3
0.2 0.4
1.3 1.5
1.3 1.5
1.3 1.5
5
12
ADJ.
5
12
ADJ.
5
12
ADJ.
5
12
ADJ.
ELECTRICAL CHARACTERISTICS (T
J
= 25°C unless otherwise stated)
V
mV
%
mV
%
V
DESCRIPTION
The LT1085 is designed to provide 3A with higher efficiency than currently available devices. All internal circuitr y is
designed to operate down to 1V input to output differential and the dropout voltage is fully specified as a function of load
current. Dropout is guaranteed at a maximum of 1.5V at maximum output current, decreasing at lower load currents.
On-chip trimming adjusts the reference output voltage to 1%. Current limit is also trimmed, minimising the stress on both
the regulator and power source circuitry under overload conditions.
The LT1085 is pin compatible with older 3 terminal adjustable regulators. A 10mF output capacitor is required on these
new devices; however, this is usually included in most regulator designs.
Unlike PNP regulators, where up to 10% of the output current is wasted as quiescent current, the LT1085 quiescent
current flows into the load, increasing efficiency.
Loading...