Page 1
MODEL 135/2
STRIP CUT PAPER SHREDDER
OPERATING & MAINTENANCE
INSTRUCTIONS
Please read this manual carefully.
It will answer all your questions regarding installation,
operation and trouble-shooting.
IMPORTANT
BE SURE TO ADHERE TO ALL SAFETY SUGGESTIONS LISTED.
READ CAREFULLY BEFORE USING
MANUAL No. 300-35
5 Walkup Drive • Westboro, MA 01581 • (508) 366-1488 • Fax (508) 836-4154 • www.semshred.com
WASHINGTON D.C. • SUWANEE, GEORGIA • SACRAMENTO, CALIFORNIA • IRVINE, CALIFORNIA • IRVING, TEXAS
The world leader in document and sensitive waste destruction solutions
Page 2
READ CAREFULLY BEFORE USING
The Model 135 is designed for the in-office destruction of paper documents. Please read
these operating instructions carefully before operating. Proper care and use of your paper
shredder will insure many years of trouble free operation.
INSTALLATION & SET UP
The Model 135 can be installed in any room equipped with a 120V/1/60 HZ electrical
service.
Observe voltage rating when inserting plug.
•
Install the paper shredder so that the main connector is easily accessible.
•
Shredder must be operated only in upright position.
•
Set up paper shredder so that the ventilation slots are unobstructed.
•
Once shredder is set up,
remove wing screws
used to secure the unit during transportation.
OPERATION
1. Press the rocker switch to energize the electronics. A green light indicates the switch has
been activated.
2. A photocell in the middle of the feed opening allows the machine to automatically turn
on when paper is passed in front of it.
3. To “stop” or “reverse” the shredder, press the rocker switch in the opposite direction.
4. If the door is open, the machine will automatically shut off. A red light indicates that
feature has been activated.
FEEDING
Feed
only paper
Do not feed
into the shredder. Paper may be fed at the rate of up to 22 sheets at a time.
plastics, paper clips or hard materials into the shredder.
03/14/00 Page 1 Model 135 Manual
Page 3
OVERLOADING
When the cutting system is “overloaded”, switch the shredder off, then into reverse to clear
the cutting system. To continue shredding, reduce the amount of material being destroyed
and restart the shredder.
CAUTION:
In the event of a severe overload or jam,
DO NOT
attempt to
clear the jam by alternately switching from forward to reverse constantly. This
action may result in motor or drive system damage, which cannot be repaired
within the scope of the guarantee. In addition, the resulting situation may require
a service technician to manually clear the overfeed.
THERMAL OVERLOAD CUT-OUT
The Model 135 Shredder is protected against excessive current draw with a built-in
thermo-element, which causes it to switch off automatically. If an overload should
happen, shut off the shredder and allow 10 to 20 minutes for the motor to cool off.
LUBRICATION
a) If shredding 10-15 minutes a day, oil cutters once a week.
b) If shredding 2-3 hours a day, oil cutters once a day.
c) For continuous shredding, oil every 15 minutes after reversing cutters
to clean out machine.
d) Do not oil a running machine.
e) After oiling, allow shredder to run for a short period of time to ensure even
distribution of the oil.
IMPORTANT:
To prevent jamming and/or clogging, it is necessary to periodically reverse
the cutters to clean them out, then lubricate the cutting unit.
03/14/00 Page 2 Model 135 Manual
Page 4
SPECIFICATIONS
Feed Opening 10" Wide
Sheets Per Feed Up to 22 Sheets
Feed Speed 24 FPM
Shred Size 1/4"
Motors 9/16 HP, 120V/1/60 HZ, 5.5 Amps.
Dimensions 31" H x 18" W x 14" D
Bag Capacity 2 CUBIC FEET
Net Weight 52 LBS
OPTIONAL ITEMS
Box of 100, Plastic Waste Bags #132 Product No. 640SB132
Case of 8, One Pint Bottles Lubricating Oil Product No. 649OIL8
Case of 16, One Pint Bottles Lubricating Oil Product No. 649OIL16
CONTACT:
Security Engineered Machinery
P.O. Box 1045
5 Walkup Drive
Westboro, MA 01581
Tel: 800/225-9293
Fax: 508/836-4154
Web Site: www.semshred.com
Email: info@semshred.com
03/14/00 Page 3 Model 135 Manual
Page 5
Qty.
Remark
Housing
Description
Part-No.:
POS
1 1133050111 Housing top........................ ..................................................1
2 1270050050 Housing bottom.................................................................... 1
3 1133050150 Safety element.................... basalt gray.................................1
4 1133050400 Ejot Pt screw ..................KB 30x25 WN 1412 ........... 2
5 1116050210 Self tapping screw.............. KB 40x25 WN 1411................. 2
6 1116050200 Self tapping screw.............. KB 40x40 WN 1411................. 2
7 1133050070 Cap..................................... 8 mm......................................... 2
8 1442999300 Label .................................. Disconnect from main...............1
9 1273999100 Machine label..................... SEM 135P ................................1
10 1111050010 Plate ..................................................................................... 2
11 1116050215 Self tapping screw.............. KA 40x10 WN 1411.................2
12 1133070010 Bottom frame..................... ..................................................1
13 1133070250 Paper basket ......................................................................... 1
14 640SB132 PE cut material bag .............................................................. 1
15 1212450900 Screw ................................. M4x12 ...................................... 2
16 1133070100 Roller ............................. .............................................4
03/14/00 Page 4 Model 135 Manual
Page 6
Qty.
Remark
Drive
Description
Part-No.:
POS
1 1270500000 Motor ............................. 220-240V/50/60 Hz .............1
2 9917985032 Cheese head screw......... M5x10..................................4
3 1270030010 Double toothed wheel.... z=65/z=13........................... 1
4 1270030020 Clevis pin ....................... .............................................1
5 1270030050 Toothed wheel................z=14; m=2.5 ........................ 1
6 1270030040 Toothed wheel................z=14; m=2.5 ........................ 1
7 1270030030 Toothed wheel................z=50; m=2 ........................... 1
8 1270030060 Frame ............................. .............................................1
9 9917500003 Screw............................. M4x55..................................6
10 9910127004 Spring washer.................A4........................................ 6
11 1270030070 Cover plate .................... .............................................1
03/14/00 Page 5 Model 135 Manual
Page 7
Qty.
Remark
Electric
Description
Part-No.:
POS
1 1110520010 Rocker switch....................................................................... 1
2 111505003 PC board ............................18-260V/50/60 Hz.................... 1
3 1108515200 Appliance couplers............................................................... 1
4 1100540200 Main supply ....................... ..................................................1
5 1212520000 Snap action switch ............. ..................................................1
6 1116050215 Self tapping screw.............. KA 40x10 WN 1411.................4
7 1110550100 Cable clip............................8................................................ 1
8 1133560010 Capacitor............................ 10 µF; 220-240V/50 Hz ........... 1
9 1100550250 Cable clip............................5................................................ 1
10 9910936008 Hexagon nut....................... M8............................................2
11 9916797004 Toothed lock washer ..........18.4 D ...................................... 2
12 1116540030 Cable.................................. gray; 220-240V.........................1
13 1112540020 Cable.................................. brown; 220-240V..................... 1
14 1116540010 Cable.................................. blue; 220-240V.........................1
15 1111050010 Plate ..................................................................................... 1
16 1100550140 Cable tie..............................small......................................... 2
17 1133540101 Cable.................................. green-yellow; 220-240V...........1
18 1437540041 Cable.................................. green-yellow; 220-240V...........1
19 1116540010 Cable.................................. blue; 220-240V.........................1
20 1133540120 Cable.................................. brown; 220-240V..................... 1
21 1212050300 Ejot Pt screw ......................KA 30x10 WN 1413.................2
22 9910933123 Hexagon nut screw............. M8x16 ...................................... 1
23 1212520010 Snap action switch ............. ..................................................1
03/14/00 Page 6 Model 135 Manual
Page 8
Qty.
Remark
Cutting Head
Description
Part-No.:
POS
1 1274020450 Cutter roll ...................... 3.9x30 mm; 333.5 mm.........1
2 1274020400 Cutter roll ...................... 3.9x30 mm; 307.5 mm.........1
3 1273020600 Distance rod ................... .............................................4
4 9917985032 Cheese head screw......... M5x10..................................8
5 1273020700 Bearing plate ................. right......................................1
6 1270020600 Flap ................................ .............................................1
7 1273020650 Bearing plate ................. left ....................................... 1
8 1116020610 Tension spring................ .............................................1
9 9926003001 Groove ball bearing........6003.2 RSR..........................4
10 1270020900 Rubber bearing............... .............................................4
11 1273020100 Flat ................................. .............................................1
12 1273020500 Stripper rod .................... .............................................2
13 9910471008 Locking ring................... 8x0.8 ....................................2
14 1274020080 Stripper .......................... top; 3 mm ............................ 22
15 1274020090 Stripper .......................... bottom; 2 mm ...................... 67
03/14/00 Page 7 Model 135 Manual
Loading...