Page 1
Security Engineered Machinery Co., Inc
OPERATIONAL & MAINTENANCE MANUAL
SEM Model 126C/2
Rev. 0
As of January 1, 2008
Security Engineered Machinery Co., Inc
NATIONWIDE SERVICE
Phone Toll Free 1(800)225-9293
Email: Service@SEMSHRED.COM
Fax: (508)366-6814
Website: WWW.SEMSHRED.com
Page 2
TABLE OF CONTENTS
Index-----------------------------------------------------------------------------------------------------------------------1
Safety Procedures & Instructions-----------------------------------------------------------------------------------2-4
Technical Data/Installation-------------------------------------------------------------------------------------------5-6
Malfunctions-------------------------------------------------------------------------------------------------------------7-9
Using and Ordering Parts------------------------------------------------------------------------------------------------9
Housing Diagram and Parts Breakdown---------------------------------------------------------------------------10-11
Cutting Head Diagram and Parts Breakdown---------------------------------------------------------------------12-13
Drive Diagram and Parts Breakdown------------------------------------------------------------------------------14-15
Electrical Diagram and list------------------------------------------------------------------------------------------16-17
Wiring Diagram-----------------------------------------------------------------------------------------------------------18
For NATIONWIDE SERVICE Call 1(800)225-9293
1
Page 3
***IMPORTANT SAFETY PROCEDURES***
Your new paper shredder incorporates powerful, heavy duty cutting mechanisms.
Serious and permanent injury may result if proper precautions are not followed.
1. This equipment should never be operated by children or individuals untrained in or
incapable of understanding the safety precautions!
2. Do not reach into the feed opening for any reason! Never insert fingers, hands, other
extremities or objects not meant to be shredded into the feed openings!
3. Do not operate or come in close proximity to this equipment wearing long hair, necktie,
loose clothing or jewelry, which may activate a photoelectric on/off switch and/or be
pulled into the machine!
4. Maintenance or repair of this equipment should be performed only by trained, authorized
service personnel.
5. Always disconnect electric power (unplug) before removing or opening the cover or other
panel giving access to internal mechanisms.
For NATIONWIDE SERVICE Call 1(800)225-9293
2
Page 4
SAFETY INSTRUCTIONS
1. Read all instructions before start-up of the paper shredder.
2. Save these instructions for later use.
3. Follow all warnings and instructions marked on the products!
4. Before cleaning the paper shredder:
a. Switch paper shredder off, unplug it from the power source
b. Clean with a damp cloth using a mild soap and water solution, the use of abrasives, petroleum
ether, benzine or diluting agent is forbidden.
5. Place this paper shredder as close as possible to power source for quick and easy unplugging.
6. Do not use this paper shredder near water.
7. This paper shredder should never be placed near or over a radiator or heat source.
8. Operation from the type of power source indicated on the name plate. If you are not sure of the type
of power available, consult your local electricity supplier.
9. Do not allow anything to rest on the power cord.
10. Do not place this paper shredder where people may walk on the cord.
11. If an extension cord is used with this paper shredder, make sure that the total of the ampere ratings
on the products plugged into the extension cord do not exceed the extension cord ampere rating.
12. Make sure no liquid is spilled on or in the paper shredder.
13. Do not attempt to repair this paper shredder yourself.
14. Switch this paper shredder off and unplug it and ask for customer service:
a. When the power cord or plug is damaged or frayed
b. If liquid has been spilled on/in the paper shredder
c. If the paper shredder has been exposed to rain
d. If the paper shredder does not operate normally when the operating instructions are followed
e. If the paper shredder has been dropped or the casing has been damaged
15. Keep paper shredder out of reach of children.
16. This shredder should be operated only with an operator in attendance
For NATIONWIDE SERVICE Call 1(800)225-9293
3
Page 5
SAFETY INSTRUCTIONS Cont……
Risk of injury!
Never insert hand, fingers or any foreign object into the paper feed opening
Risk of injury by pulling in!
Keep long hair, loose articles of clothing, ties scarves, jewelry, etc. away from
feed opening. Material with the tendency to form loops, eg. tapes, strapping
material, etc. must not be shredded.
Before taking off the cover, changing the location, cleaning or anything else other
than normal operation turn off and unplug the paper shredder!
Maintenance and service work may be performed only by an authorized SEM
Service Representative.
USE ACCORDING TO INSTRUCTIONS
The paper shredder is intended only for shredding normal paperwork.
Using the shredder in a different way or beyond the scope described here, is regarded as not being in
accordance with the instructions.
Use according to instructions also includes following of the operating instructions.
For example; shredding of the following is not allowed:
Plastics bags of any kind, plastic film, adhesive tape, sheet metal or plastic signs,
plywood or balsa wood, staples or paper clips.
For NATIONWIDE SERVICE Call 1(800)225-9293
4
Page 6
TECHNICAL DATA
Shred Size: 1 x 5 mm
Max. No. of Sheets: Up to 5 Sheets
Shredding Speed: 27 FPM
Throat Width: 10"
Power: 5/8 HP @ 7 Amps
Voltage: 115V/1/60 HZ
Dimensions: 33"H x 18"W x 14"D
Weight: 70 lbs.
INSTALLATION
1 Connect plug to 115 Volt wall outlet
2. Paper shredder must only be operated in upright position
3. Set up paper shredder so that the ventilation slots are free
4. To ensure sufficient ventilation of the shredder a clearance of at least 10cm must be
maintained from the walls or any furniture
Before start-up:
Undo the wing screws securing the unit
during transportation
Inserting the bag for shredded material:
For NATIONWIDE SERVICE Call 1(800)225-9293
5
Page 7
INSTALLATION Cont….
Open front door and pull out frame with bag for shredded material. Fold new bag around frame and
allow to, overlap by approximately 20cm. Push frame with guide and bag into bottom frame, close front
door.
Insert main plug in power socket.
Switching the paper shredder ON
Switching the paper shredder OFF
Read operating instructions before pulling shredder into operation.
Press rocker switch position 1
• Rocker switch locks in
• Paper shredder is ready for operation (standby)
Green LED on control panel lights
Feed paper (see "Technical Data" for sheet capacity)
• The shredding process is stated by a photo cell in the paper feeding opening.
When the paper feeding opening is free again, the cutting system
automatically switches off after approximately 3 seconds and returns to
standby.
Press rocker switch position 2
• Rocker switch resets
For NATIONWIDE SERVICE Call 1(800)225-9293
to zero position
6
Page 8
TROUBLESHOOTING
If the paper shredder does not work properly, please check the following:
1. Is the main plug inserted into the main power outlet?
2. Is the paper shredder turned on?
3. Is the paper shredder front door closed?
4. Is the front door closed?
5. Is the bag full?
6. Is there a paper jam?
7. Is the motor overloaded(motor should cool down approximately 15-20 minutes)
If none of the above applies and the paper shredder still does not run, please contact our Customer Service
Department at 1(800)225-9293.
Malfunctions:
Paper Jam (too much paper input)
Red LED on control panel lights
• Paper shredder switches off automatically
Paper shredder is blocked
Caution!
Do not press rocker switch alternately forwards/backwards (pos.1/2)
• Cutting unit can be damaged
Instead
Press and hold down rocker switch pos.2
• Paper is pushed out
Separate paper stack
Press rocker switch pos. 1
Feed paper successively
Red LED on control panel lights
• Paper Shredder switches off
Paper shredder blocked
Press and hold down rocker switch pos.2
• Paper is pushed out
Paper must be pulled out of paper feed opening
Photo-cell becomes free
Separate paper stack
Press rocker switch pos.1
Feed paper successively
For NATIONWIDE SERVICE Call 1(800)225-9293
7
Page 9
TROUBLESHOOTING Cont…
Electric Motor Overheated
Red LED on Control panel lights
• Paper shredder switches off automatically
Tap rocker switch pos.2
• Rocker switch resets to zero position
Allow paper shredder to cool sown for approximately 15 to 20 minutes
Press rocker switch pos. 1
Shredder Material Container Full
Red LED on control panel lights
• Paper shredder switches off
Remove full shredded material bag and insert new bag
Close front door of paper shredder
Tap rocker switch pos. 2
Press rocker switch pos. 1
Paper shredder is ready for operation again
Empty the shredded material container after the paper shredder has been switched off, because
otherwise malfunction of the cutting system could occur when the rocker switch is pressed
several times in succession.
Door Contact Interrupted
Red LED on control panel lights
• Paper shredder switches off
Check whether front door is closed properly
Tap rocker switch pos.2
Press rocker switch pos.1
Paper shredder is ready for operation again
When the cutting capacity drops or the noise increases:
Switch paper shredder off
• Tap rocker switch pos. 2
• The rocker switch jumps to position 0
Squirt SEM shred oil in a figure 8 motion onto a sheet of paper and feed it into the shredder.
For NATIONWIDE SERVICE Call 1(800)225-9293
8
Page 10
TROUBLESHOOTING Cont…
Run cutting system forwards and backwards (pos.1-pos. 2) several times without
feeding paper.
Paper dust and particles are shaken off.
USING AND ORDERING SPARE PARTS
Only use original SEM spare part replacements
We guarantee their quality and functional reliability
Warranty claims on parts and/or service must be approved by SEM's Customer Service Manager
HINTS FOR ORDERING SPARE PARTS
The spare parts shown on the following pages have part numbers. This spare parts list shows the
following information with respect to the spare parts to be ordered.
Part No. • Dimensions • Quantity
Designation • Item No.
In order to avoid errors and the delivery of wrong parts, each parts order should contain the following
information.
• Machine Type and Serial No. (See nameplate)
• Part No. and designation of desired spare parts
• Quantity of desired spare parts
• Desired mode of shipment (e.g. post, freight, express)
• Full address of purchaser
RECOMMENDED SPARES/OPTIONAL ITEMS AVAILABLE
Replacement Plastic Waste Bags #130 Part No. 640SB130
Shredder Lubricating Oil, Case of 8 pints, Part No. 6490IL8 HV
For NATIONWIDE SERVICE Call 1(800)225-9293
9
Page 11
CABINET/HOUSING
For NATIONWIDE SERVICE Call 1(800)225-9293
10
Page 12
CABINET /HOUSING PARTS BREAKDOWN
ITEM PART NO. DESCRIPTION DIMENSION DIN QTY
1 SH1133050113 Housing top 448 1
2 SH1562999010 Label 32 x 270 1
3 SH1133050158 Safety Element 295 x CA.70 x 70 1
4 SH1116050210 EJOT Screw D=4 L=25 2
5 SH1133050400 EJOT Screw D=3 L=25 1
6 SH1442999300 Label 20x48 1
7 SH1270050052 Housing Bottom 400 x 300(310) x 153 1
8 SH1116050220 EJOT Screw D=14 L =18 2
9 SH1271150101 Bottom Frame 1
10 SH1133070101 Fixed Roler D=14, 5 H=18 4
11 SH1271070400 Frame 300(283) x 391 x 406 1
12 SH1212450900 Screw M4 x 12 2
13 SH1133050070 Cap Black D=8 DK=9, 5 C=8 1
14 SH1271070530 Cup Hinge 2
15 SH1271070540 Mounting Plate 2
16 SH1250070030 Guide Rod 20 x 20 x 200 2
17 SH1250070920 Screw 4 x 15 96 4
18 638SB138A Plastic Bag 440/370 x 850 x 0, 06 1
19 SH1133050122 Housing Top Complete 1
20 SH1270070200 Door cpl. 1
21 SH1271070101 Bottom Unit 1
For NATIONWIDE SERVICE Call 1(800)225-9293
11
Page 13
CUTTING HEAD
For NATIONWIDE SERVICE Call 1(800)225-9293
12
Page 14
CUTTING HEAD PARTS BREAKDOWN
ITEM PART NO. DESCRIPTION DIMENSION DIN QTY
1 SH1562020450 Cutter roll long 0, 86x5 mm 1
2 SH1562020400 Cutter roll short 0,86x5 mm 1
3 SH1273020600 Distance Rod RD12x268,1 669 2
4 SH9917985033 Cheese head screw M 5x12 985 4
5 SH1275020700 Bearing plate, right side 140x103x15 1
6 SH1270020600 Flap 1
7 SH1275020650 Bering plate metal left BL 3x113,45x251,31 1
8 SH1116020610 Tension spring L=28 D=6 DD=0.4 223 1
9 SH9926003001 Deep groove ball bearing DI=17 DA=35 B=10 4
10 SH1270020900 Rubber bumper 8x10x15 4
11 SH1273020500 Flat FL 16x4x275+-0,5 174 1
12 SH1273020500 Stripper rod RD 18x292,5 668 2
13 SH9910471008 Locking Ring 8x0,8 471 2
14 SH1275020080 Stripper, top BL 0,6-0,05 32
15 SH1275020090 Stripper bottom BL 0,6 53x60 624 334
16 SH117202100 Guide black 19x13,5x268,1 1
17 SH1172050400 EJOT Screw D=3 L=10 4
18 SH1180550100 Distance tube 83056 M3, L5,0 AD6, 0 MM 2
19 SH1172020565 Stripper rod RD 12x289 668 2
20 SH9910471012 Locking ring 12x1 471 4
For NATIONWIDE SERVICE Call 1(800)225-9293
13
Page 15
DRIVE
For NATIONWIDE SERVICE Call 1(800)225-9293
14
Page 16
DRIVE PARTS BREAKDOWN
ITEM PART NO. DESCRIPTION DIMENSION DIN QTY
1 SH1710500010 Capacitor motor 1
2 SH9917985032 Oval head cap screw M 5x10 985 4
3 SH1270030010 Toothed wheel z=65 m=1,25/z=13 m=2 D=92,1 B=47 1
4 SH1270030020 Bolt RD 16x53,25 1
5 SH1270030055 Toothed wheel z=13 m=2,75 D=42 B=19,7 1
6 SH1270030045 Toothed wheel z=13 m=2,75 D=70 B=27,2 1
7 SH1270030030 Toothed wheel z=50 m=2 D=110 B=20 1
8 SH1270030060 FRAME 234,5X118X47 1
9 SH9917500003 Screw M 4X55 500 6
10 SH9910127004 Spring washer A 4 127 6
11 SH1270030070 Cover Plate BL 1,5x118,4228,5 1
For NATIONWIDE SERVICE Call 1(800)225-9293
15
Page 17
ELECTRIC
For NATIONWIDE SERVICE Call 1(800)225-9293
16
Page 18
ELECTRIC PARTS BREAKDOWN
ITEM PART NO. DESCRIPTION DIMENSION DIN QTY
1 SH1110520010 Rocker switch 1
2 SH1212505010 Light barrier 1
3 SH1212505080 LED display 300 MM 1
4 SH1100540220 Cable assembly w/US-plug 2000 MM 1
5 SH1108515200 Appliance inlet plug 6,3 MM 1
6 SH1438505050 Electronic circuit board 1
7 SH1133560120 Capacitor 45 uF 240V 1
8 SH9910936008 Hexagon nut M8 936 1
9 SH9916797004 Toothed lock washer 18,4 797 1
10 SH1212540050 Cable 190 MM 1
11 SH1110550100 Cable clip 8mm Polyamid 6.6 2
12 SH1284540070 Cable 240 MM 1
13 SH1212540031 Cable 270 MM 1
14 SH1250540020 Cable 230 MM 1
15 SH1212505070 Rotation sensor 300 MM 1
16 SH1400020950 O-ring DI=10 D=2 1
17 SH9910471010 LOCKING RING 10x1 471 1
18 SH1400505101 Magnet NR.0075-08 1
19 SH1212520000 Snap Switch 1
20 SH1100550250 Cable clip 5 mm Polyamid 6.6 1
21 SH1100550140 Cable tie small 3
22 SH148754010 Cable 300 MM 1
23 SH1133540160 Cable 440 MM 1
24 SH1212520011 Snap-action switch D374-VGAC SCHLIEßER 10(4)A 250V 1
25 SH1456540110 Cable 200 MM 1
26 SH1111050010 Plate PL 2x14x55 2
27 SH1116050215 EJOT Screw D=4 L=10 4
For NATIONWIDE SERVICE Call 1(800)225-9293
17
Page 19
WIRING DIAGRAM
For NATIONWIDE SERVICE Call 1(800)225-9293
18
Loading...