Selcon PRG-SE-C, PRG-SE-C-O2 Technical Sheet

PROGRAMMER FOR START, FLAME SUPERVISION

AND SAFE STOP OF BURNER

PRODUCT: PRG-SE-C

 Costumer Service 55 11 3019-1616



- O2 TECHNICAL SHEET 1/11

For further details see technical bulletin

•

APPLICATION

Programmer PRG-SE-C-O2 equipment recommended for start, flame supervision and safe stop for
any type of burner for up to two stages of flame, in commercial applications or industrial and fuels gas
or light liquids, with a cycle of use do not continuum (on/off burner Period in less than 24 hours).

For use in closed combustion camera, the user should provide safe system of pre-purge
before each sequence of start, or require the programmer PRG-SE-C-O2 with purge timer coupled,

since that the times offered are appropriate for application.
Entry for flame sensor for ionization. See electrode sensors for ionization, line SEL-HT-I (standard) or
SEL-HT-E (electrode mounted on a drawing or sample of the client).

This product meets the requirements of the standard NBR 12313 of ABNT-review

Sept./2000.

•

TECHNICAL DATA

⇒⇒⇒⇒

Watch dog micro process – safe failure.

⇒⇒⇒⇒

Supply/frequency: 90 a 250Vca - 50/60 Hz ± 3% or 24Vcc (-10 +20%).

NOTE: To supply network CA, consisting of phase/neutral, should consider the

possible need for its reversal (terminals 9 and 10), for flame sensor circuit not

lose sensitivity and therefore the capacity to detect signal of flame. See below

diagram for the connections AC and DC.

⇒⇒⇒⇒

Consumption of energy: 5 VA

⇒⇒⇒⇒

Protection against tension outbreaks

⇒⇒⇒⇒

Protection fuses retardate the internal circuitry (0,25A) and for the control outputs (6,3A)

⇒⇒⇒⇒

Temperature of work: 0 at 60 ºC

⇒⇒⇒⇒

Storage ambient temperature: -5° a 65 °C

⇒⇒⇒⇒

Maximum relative humidity of environment in operation: 90% (40 ± 2°C) – NBR 5291

⇒⇒⇒⇒

Flame Sensor : Ionization.

⇒⇒⇒⇒

Minimum current flame for supply of 90 at 250Vca: 2 microampers dc (uA).

⇒⇒⇒⇒

Minimum current flame for supply in 24 Vcc: 7 uA microampers dc (uA).

NOTE: The cable of flame sensor must be installed separately from other cables that

are part of the command set of the burner. The best type of cable recommended for

this purpose is used for ignition.

⇒⇒⇒⇒

Protection against short circuit failure sensor ionization for mass.

⇒⇒⇒⇒

Blocking with local signaling (type LED) and remote (contact of relay N.A.)

⇒⇒⇒⇒

With verification of premature flame or false flame signal, before starting the burner.

⇒⇒⇒⇒

Purge Time: 10 or 20 seconds (see field code for request)

⇒⇒⇒⇒

Maximum time for confirmation of contact closure of the PS of combustion air: 5 sec.

SELCON

Automação Industrial

SELCON S

CNPJ 56.935.877/0001-29

Street Américo Samarone, 502 • CEP 04284-000 • Moinho
Velho • São Paulo • SP • Tel/Fax: [phone]

http://www.selcon.com.br

Selcon Ltda., keeps the right to modify this technical sheet

when never it is necessary

ISTEMAS ELETRÔNICOS DE CONTROLE LTDA

–

February/10

.

Representative or Distributor:

1/11

PROGRAMMER FOR START, FLAME SUPERVISION

AND SAFE STOP OF BURNER

PRODUCT: PRG-SE-C

 Costumer Service 55 11 3019-1616

⇒⇒⇒⇒

Time of ignition: 6 sec.

⇒⇒⇒⇒

Time to confirm the signal of flame: < 1 sec.

⇒⇒⇒⇒

Time of answer to the flame flaw: < 4 seg.

⇒⇒⇒⇒

BARGRAF of LED’s:

•

Signaling

•

Signaling

•

Signaling

•

Signaling

•

Signaling

•

Signaling

•

Signaling 7

(BLINK, BLINK)

•

Signaling

1 – ¨PUR

2 – ¨IGN

3 –

4 – ¨N3

5 – ¨N2

6 – ¨N1

8 – ¨ANT¨ 



- O2 TECHNICAL SHEET 2/11

For further details see technical bulletin

¨

 BURNER IN PURGE

¨

 BURNER IN IGNITION

¨

N4

¨

 LEVEL OF FLAME

¨

 LEVEL OF FLAME

¨

 LEVEL OF FLAME

¨

 LEVEL OF FLAME

– ¨FCH

¨

 FAILURE OF IGNITION / FLAME FAILURE (fixed access)



DEFECT SENSOR - SHORT CIRCUIT FOR OF MASS

- available only for the model fed on 24Vdc

FAILURE FOR FLAME PREMATURE OR FALSE

•

Signaling

•

Signaling

NOTE: The flame sign will be greater the higher the level "N" indicated

⇒⇒⇒⇒

Maximum current per output in 250 Vac (resistive):

••••

VE

••••

TI

••••

V1

••••

V2

••••

AL

⇒⇒⇒⇒

Electric connections: through socket of fast extraction polarized, type terminal rule,

to receive the external cables.

⇒⇒⇒⇒

Expected electrical life of output contacts:> 100,000 operations.

⇒⇒⇒⇒

Expected mechanical life of output contacts:> 10,000,000 operations.

⇒⇒⇒⇒

Reset local and remote after 3(three) sec. waiting for security to enable the reset system.

⇒⇒⇒⇒

Auto Test of key air flow or pressure switch: (NA) before start the fan, and (NC)
continuously after the start of the fan.

⇒⇒⇒⇒

Degree of environmental protection: IP 54 (except connector of fast extraction - IP 50)

⇒⇒⇒⇒

Cabinet: Plastic box gray color

⇒⇒⇒⇒

Mounting: External or internal on flat surface in protected environment.

9 – ¨PSA

10 – ¨PSF¨ 

(ventilator): 2 A

(transformer of ignition): 2 A

(low fire or pilot): 2 A

(high fire): 2 A

(alarm): 2 A

¨

 FAILURE PS AIR COMBUSTION OPENED

FAILURE PS AIR COMBUSTION CLOSED

SELCON

Automação Industrial

SELCON S

CNPJ 56.935.877/0001-29

Street Américo Samarone, 502 • CEP 04284-000 • Moinho
Velho • São Paulo • SP • Tel/Fax: [phone]

http://www.selcon.com.br

Selcon Ltda., keeps the right to modify this technical sheet

when never it is necessary

ISTEMAS ELETRÔNICOS DE CONTROLE LTDA

–

February/10

.

Representative or Distributor:

2/11

PROGRAMMER FOR START, FLAME SUPERVISION

97

35

AND SAFE STOP OF BURNER

PRODUCT: PRG-SE-C

 Costumer Service 55 11 3019-1616

⇒⇒⇒⇒

Fixation: 3 screws on plane surface.

⇒⇒⇒⇒

Weight : 300 grams

⇒⇒⇒⇒

Warranty: 12 months (see the guarantee)



- O2 TECHNICAL SHEET 3/11

For further details see technical bulletin

•

Dimensional drawing (mm) - version for supply AC-90 to 250V

PART IDA

RR

SELC ON LTDA .

Indús tria Brasile ira

PROD UTO:

Alime ntação:

90-25 0VCA~50/ 60Hz

109

PRG-SECAMPO

TI

CHAM A

ALARM ES

AL V1 V2 VE PS R L2

1

PUR

2

IGN

3

N4

4

N3

5

N2

6

N1

7

FCH

8

ANT

9

PSA

10

PSF

654321 7 8 9 1 0

V

I

E100

R

14 15 16

11 12 13

~

95

14

FIGURE 1

•

Main ruler of terminals (10 terminals) and additional (optional 3 +3 terminals) - AC 90 to 250V

1

2

3

4

5

6

7

8

9

10

SELCON

Automação Industrial

SELCON S

CNPJ 56.935.877/0001-29

Street Américo Samarone, 502 • CEP 04284-000 • Moinho
Velho • São Paulo • SP • Tel/Fax: [phone]

ISTEMAS ELETRÔNICOS DE CONTROLE LTDA

http://www.selcon.com.br

Selcon Ltda., keeps the right to modify this technical sheet

when never it is necessary

–

February/10

FIGURE 2

.

Representative or Distributor:

3/11

PROGRAMMER FOR START, FLAME SUPERVISION

AND SAFE STOP OF BURNER

PRODUCT: PRG-SE-C

 Costumer Service 55 11 3019-1616



- O2 TECHNICAL SHEET 4/11

For further details see technical bulletin

•

Scheme of electric connections CA - version for supply CA - 90 to 250V:

1
2
3
4

F (6,3A)

5
6
7
8
9

10

AL V1 V2 VE

ICC> 2uAdc

PRG-SE-C -O2

R

654321 7 8 9 10

V

+

PS R L2 L1(N)

_

uA

_

~

14 15 16

11 12 13

SELCON

Automação Industrial

ACS-TE - 1-CTI

G

SELCON S

CNPJ 56.935.877/0001-29

Street Américo Samarone, 502 • CEP 04284-000 • Moinho
Velho • São Paulo • SP • Tel/Fax: [phone]

http://www.selcon.com.br

Selcon Ltda., keeps the right to modify this technical sheet

when never it is necessary

ISTEMAS ELETRÔNICOS DE CONTROLE LTDA

–

February/10

I

FIGURE 3

.

Representative or Distributor:

4/11

PROGRAMMER FOR START, FLAME SUPERVISION

AND SAFE STOP OF BURNER

PRODUCT: PRG-SE-C

 Costumer Service 55 11 3019-1616

•

Dimensional drawing (mm) - version for supply DC in 24Vcc:

99.5



- O2 TECHNICAL SHEET 5/11

For further details see technical bulletin

PART IDA

R

SELCON L TDA.

Indústria Brasileira

PROD UTO:

PRG-SECAMPO

TI AL V1 V2

CHAM A

ALARM ES

4321 9 10

9735

1

PUR

2

IGN

3

N4

4

N3

5

N2

6

N1

7

FCH

8

ANT

9

PSA

10

PSF

Alime ntação:

24 Vcc

65 7 8

VE I PS RV24v

E115

R

95

-

+

4.5

FIGURE 4

•

Scheme of electric connections - version for supply DC in 24Vcc:

1

F (6,3A)

2
3
4
5
6
7
8
9

10

PRG-SE-C 1-O2

R

654321 7 8 9 10

V

+

uA

_

I

AL V1 V2 VE PS R

_ _

ICC> 7uA<250uADC

ACS-TE-05-C5

TI

G

FIGURE 5

-

24v

+

SELCON

Automação Industrial

SELCON S

CNPJ 56.935.877/0001-29

Street Américo Samarone, 502 • CEP 04284-000 • Moinho
Velho • São Paulo • SP • Tel/Fax: [phone]

http://www.selcon.com.br

ISTEMAS ELETRÔNICOS DE CONTROLE LTDA

Selcon Ltda., keeps the right to modify this technical sheet

when never it is necessary

–

February/10

.

Representative or Distributor:

5/11

PROGRAMMER FOR START, FLAME SUPERVISION

AND SAFE STOP OF BURNER

PRODUCT: PRG-SE-C

 Costumer Service 55 11 3019-1616

•

LEGEND



- O2 TECHNICAL SHEET 6/11

For further details see technical bulletin

L1 / L2 (N): Power Input 90 to 250Vac or 24Vdc (see code for request).

Ps: Pressure switches for minimum gas (permission of start).

Rearme: Reset local

R: Reset remote

VE: Fan

PS: Key of flow of air / key of pressure of combustion air and/or exhaustion

TI: Transformer of ignition:

••••

We recommend using the model ACS-TE--C5 or ACS-TE -1-C6.

For other transformers of Ignition, consult Selcon Ltda.

G: Electrode ignitor – line SEL-HT

I: Sensor electrode of flame for ionization – line SEL-HT

V1: Pilot valve (1º stage / pilot / fire low)

V2: Main valve (2º stage / main / fire high)

AL: Alarm of flame premature or false; failure of ignition; failure of flame in regime;

circuit short short of the flame sensor.

Q: Burner-pilot and main; low fire and high or of 2 stages.

SELCON

Automação Industrial

SELCON S

CNPJ 56.935.877/0001-29

Street Américo Samarone, 502 • CEP 04284-000 • Moinho
Velho • São Paulo • SP • Tel/Fax: [phone]

http://www.selcon.com.br

Selcon Ltda., keeps the right to modify this technical sheet

when never it is necessary

ISTEMAS ELETRÔNICOS DE CONTROLE LTDA

–

February/10

.

Representative or Distributor:

6/11

PROGRAMMER FOR START, FLAME SUPERVISION

AND SAFE STOP OF BURNER

PRODUCT: PRG-SE-C

 Costumer Service 55 11 3019-1616

•

Diagram of times



- O2 TECHNICAL SHEET 7/11

For further details see technical bulletin

TIMES

t1 Wait to start sequence 1 sec.
t2 Wait for stabilization of the key signal of air flow 5 sec.
t3 Purge 0, 10 or 20 sec.
t4 Pre-ignition 2 sec.
t5 Ignition 6 sec.
t6 Stabilization pilot flame or 1st stage. 8 sec.

•

Operation starting with the formation of normal flame

t0

~

L1-L2(N)

t1

PS

t2

TERMINALS FOR
ELECTRICAL
CONNECTIONS

9/10

7

SELCON

Automação Industrial

VE

V

t3

TI

V1

V2

I

AL

R

FIGURE 6

SELCON S

CNPJ 56.935.877/0001-29

Street Américo Samarone, 502 • CEP 04284-000 • Moinho
Velho • São Paulo • SP • Tel/Fax: [phone]

http://www.selcon.com.br

Selcon Ltda., keeps the right to modify this technical sheet

when never it is necessary

ISTEMAS ELETRÔNICOS DE CONTROLE LTDA

–

February/10

5

t4

1

t5

3

t6

4

6

2

8

.

Representative or Distributor:

7/11

PROGRAMMER FOR START, FLAME SUPERVISION

t0

AND SAFE STOP OF BURNER

PRODUCT: PRG-SE-C

 Costumer Service 55 11 3019-1616

•

Operation starting with the presence of premature flame / false signal



~

L1-L2(N)

PS

VE

V

TI

V1

V2

I

AL

R

- O2 TECHNICAL SHEET 8/11

For further details see technical bulletin

TERMINALS FOR

t0

ELECTRICAL
CONNECTIONS

9/10

7

5

1

3

4

6

2

8

•

Operation of start with ignition failure

t0

~

V

L1-L2(N)

PS

VE

TI

V1

V2

I

AL

R

t1

t2

FIGURE 7

t3

t4

t5

FIGURE 8

TERMINALS FOR
ELECTRICAL
CONNECTIONS

9/10

7

5

1

3

4

6

2

8

t0

SELCON

Automação Industrial

SELCON S

CNPJ 56.935.877/0001-29

Street Américo Samarone, 502 • CEP 04284-000 • Moinho
Velho • São Paulo • SP • Tel/Fax: [phone]

http://www.selcon.com.br

ISTEMAS ELETRÔNICOS DE CONTROLE LTDA

Selcon Ltda., keeps the right to modify this technical sheet

when never it is necessary

–

February/10

.

Representative or Distributor:

8/11

PROGRAMMER FOR START, FLAME SUPERVISION

t0

t0

AND SAFE STOP OF BURNER

PRODUCT: PRG-SE-C

 Costumer Service 55 11 3019-1616

•

Operation of start with pre-existent flaw of the key of flow of air



~

L1-L2(N)

PS

VE

V

TI

V1

V2

I

AL

R

- O2 TECHNICAL SHEET 9/11

For further details see technical bulletin

TERMINALS FOR

t0

ELECTRICAL
CONNECTIONS

9/10

7

5

1

3

4

6

2

8

FIGURE 9

•

Operation of start with flaw of the key of flow of air after entering in regime.

t0

~

V

L1-L2(N)

PS

VE

TI

V1

V2

t1

t2

t3

t4

t5

t6

TERMINALS FOR

ELECTRICAL

CONNECTIONS

9/10

7

5

1

3

4

I

AL

R

6

2

8

FIGURE 10

SELCON

Automação Industrial

SELCON S

CNPJ 56.935.877/0001-29

Street Américo Samarone, 502 • CEP 04284-000 • Moinho
Velho • São Paulo • SP • Tel/Fax: [phone]

http://www.selcon.com.br

ISTEMAS ELETRÔNICOS DE CONTROLE LTDA

Selcon Ltda., keeps the right to modify this technical sheet

when never it is necessary

–

February/10

.

Representative or Distributor:

9/11

PROGRAMMER FOR START, FLAME SUPERVISION

AND SAFE STOP OF BURNER

PRODUCT: PRG-SE-C

 Costumer Service 55 11 3019-1616

•

Operation of normal start with lack and subsequent electric power return.

t0

~

V

L1-L2(N)

PS

VE

TI

V1

V2

I

AL

R

t1



- O2 TECHNICAL SHEET 10/11

For further details see technical bulletin

t0

t1

t2t2

t4t3

t5

t6

RETURN OF ENERGY / NORMAL OPERATION

t4t3

t5

FIGURE 11

•

Equipment lock with momentary lack of energy

t0

~

L1-L2(N)

TERMINALS FOR
ELECTRICAL
CONNECTIONS

t6

TERMINALS FOR
ELECTRICAL
CONNECTIONS

PS

VE

V

TI

V1

V2

I

AL

R

SELCON

Automação Industrial

SELCON S

CNPJ 56.935.877/0001-29

Street Américo Samarone, 502 • CEP 04284-000 • Moinho
Velho • São Paulo • SP • Tel/Fax: [phone]

http://www.selcon.com.br

ISTEMAS ELETRÔNICOS DE CONTROLE LTDA

Selcon Ltda., keeps the right to modify this technical sheet

when never it is necessary

–

February/10

FIGURE 12

.

Representative or Distributor:

10/11

PROGRAMMER FOR START, FLAME SUPERVISION

-

AND SAFE STOP OF BURNER

PRODUCT: PRG-SE-C

 Costumer Service 55 11 3019-1616

•

CODE OF REQUEST

PRG-SE -



PRG-SE-C

TIME OF

PURGE

- O2 TECHNICAL SHEET 11/11

For further details see technical bulletin



-O2

C-

SETUP

FAN + KEY OF

AIR FLOW

O-

OPTION

SUPPLY

 (d1)

d1 = 0 => 0 sec.

OR

d1 = 1 => 10 sec.

OR

d1 = 2 => 20 sec.

Obs.: The sensor and other accessories must be specified separately, according to a specific
code.

• B

EWARE

⇒⇒⇒⇒ Use the programmers and/or relays detectors exclusively with flame sensors manufactured
by the Selcon.

•

OTHER PRODUCTS AND ACCESSORIES:

⇒⇒⇒⇒

Flame relays : CHM-SE, CHM-P, CHM-M, CHM-M-IIIMe (with base) and CHM-F

⇒⇒⇒⇒

Relay tester tightness of shutoff valves: CHM-T

⇒⇒⇒⇒

Programmers ignition and flame monitoring: PRG-SE, PRG-E, PRG-Ie,
PRG-Ie-IIIMe (with base), PRG-I, PRG-M and PRG-M-M-IIIMe (with base)

⇒⇒⇒⇒

Optical flame sensors: SEL-SV.

⇒⇒⇒⇒

Sensors flame ionization electrodes and igniters: SEL-HT (standard) and SEL-HT-E
(sensors and electrodes mounted on a drawing or sample of client-special).

⇒⇒⇒⇒

Signal transmitter of flame ACS-TX (up to 500 meters between sensor and relay or

programmer).

⇒⇒⇒⇒

Signal converter flame 4 -20 mA: ACS-CV

⇒⇒⇒⇒

Transformers Ignition : ACS-TE (for supply on VAC or VDC)

⇒⇒⇒⇒

Panel ignition timer: ACS-IT

⇒⇒⇒⇒

Ignitor portable: ACS-IP (operates with batteries)

⇒⇒⇒⇒

Panel ignition (operates with batteries): ACS-PN-E

⇒⇒⇒⇒

Panel ignition and flame monitoring: PRG-Ie/O3

⇒⇒⇒⇒

Different cables: ACS - CB (ignition / sensing / communication / control)

⇒⇒⇒⇒

Connector and shield to touch for cable of ignition: ACS-CP

⇒⇒⇒⇒

Junction of articulation : ACS-CN

⇒⇒⇒⇒

Panel ignition and monitoring: ACS-PN (under consultation)

⇒⇒⇒⇒

Services of reform of pilot burners: under consultation

⇒⇒⇒⇒

LINE OF SUPERVISORS PRODUCTION DATA

:

 (d2)

d2 = 1 => without

OR

d2 = 2 => with

 (d3)

d3 =

0

=>

90 a 250 Vac­50/60 Hz

OR

d4= 2 => 2 stages

d3 = 1 => 24Vcc

SELCON

Automação Industrial

SELCON S

CNPJ 56.935.877/0001-29

Street Américo Samarone, 502 • CEP 04284-000 • Moinho
Velho • São Paulo • SP • Tel/Fax: [phone]

http://www.selcon.com.br

Selcon Ltda., keeps the right to modify this technical sheet

when never it is necessary

ISTEMAS ELETRÔNICOS DE CONTROLE LTDA

–

February/10

.

Representative or Distributor:

11/11