Seiko V192 User Manual
V192 JSYV192D1-A1909
INSTRUCTIONSDIVER’S WATCH FOR AIR DIVING
D-13
V192
日本語
..................................................
English ................................................
そのほかの言語の取扱説明書は、パソコンや
スマートフォンから当社ホームページ内の
「カスタマーサービス」>「取扱説明書ダウンロード」
にアクセスいただき、ご覧ください。
Please refer to the Instruction Manuals
of other languages by accessing
"Customer Service"→ "Instruction"
on our Website from PC or Smartphone.
JA
EN
1
1
Deutsch / Français / Italiano / Español /
Pусский язык / / Português /
䬁Ổ
ᶮ㔈
/
䷂橕ᶮ㔈
/
㭛⧄
/
https://www.seikowatches.com/
Thank you very much for choosing a SEIKO watch.
WARNING
Make sure to read the following instructions before use and strictly observe them.
CAUTION
Make sure to read the following instructions before use and strictly observe them.
For proper and safe use of your SEIKO watch,
please read carefully the instructions in this
booklet before using it.
Keep this manual handy for easy reference.
* Length adjustment service for metallic bands is available at the retailer from
whom the watch was purchased. If you cannot have your watch repaired by
the retailer from whom the watch was purchased because you received the
watch as a gift, or you moved to a distant place, please contact SEIKO
CUSTOMER SERVICE CENTER. The service may also be available on a
chargeable basis at other retailers, however, some retailers may not undertake
the service.
* If your watch has a protective film for preventing scratches, make sure to peel
it off before using the watch. If the watch is used with the film on it, dirt, sweat,
dust, or moisture may be attached to the film and may cause rust.
EN
1
b
b WARNING
When diving, never carry out operations other than those specified in this instruction manual. Mishandling
of the product and misunderstanding of the displayed content may lead to a fatal or serious accident.
b
WARNING
The diver’s watch is an auxiliary instrument which mainly displays the passage of time and does not ensure
the safety of a user. Use this watch while using the equipment (residual pressure gauge, water depth meter,
etc.) required for safe diving.
b
WARNING
Never use this watch for “saturation diving” using helium gas.
b
WARNING
Do not dive using this product unless you have been properly trained in scuba diving, acquired the requisite
experience and techniques for safe diving, thoroughly familiarized yourself with the operation and handling
of this product, and inspect all functions of this product prior to each dive.
EN
2
b
b CAUTION
Inspect the following items before diving (excluding saturation diving):
• The watch is normally operating.
• The remaining battery level is sufficient and the mainspring is sufficiently wound.
• The rotating bezel turns smoothly. (The bezel rotation must not be too loose or too tight.)
• Screws of the crown and other parts are reliably tightened.
• No abnormalities such as flaws or cracks exist on the band or glass.
• The band is reliably fixed (with spring bar, buckle or other parts.)
* If any abnormality is observed in the above items, do not use this watch for diving.
b CAUTION
Do not operate the crown or buttons underwater.
b
CAUTION
As the use environment of the diver’s watch may affect not only the case or band but also the internal
mechanism of the watch, we recommend that you periodically request an overhaul for inspection and
adjustment approximately once every three to four years.
EN
3
CONTENTS
Manual date adjustment at the end of the
month
If the hands fail to move or move abnormally
even after recharging
1 HOW TO USE
Handling cautions ............................................ 6
Precautions for diving (Please make sure to
observe the following.) .................................. 10
Before diving .............................................. 10
While diving ............................................... 12
After diving ................................................. 13
Structure of the case .................................. 14
Characteristics .............................................. 15
Names of the parts and their functions .......... 16
Screw down crown ........................................ 17
Screw lock type button .................................. 18
Toggling between displays ............................ 19
How to use the rotating bezel ........................ 20
2 HOW TO SET THE TIME AND DATE
How to set the time and date ......................... 22
How to set the time and date ..................... 22
........................................................ 25
3 HOW TO USE THE STOPWATCH
Stopwatch function ........................................ 26
The names of the parts and functions of the
stopwatch .................................................. 26
Before using the stopwatch ....................... 27
How to use the stopwatch ............................. 29
4 SOLAR CHARGING FUNCTION
Charging the battery ...................................... 33
How to charge the battery .......................... 33
Guide to charging times ............................. 34
About energy ................................................. 35
How to display the energy level ................. 35
5 TO PRESERVE THE QUALITY OF YOUR
WATCH
Daily care ...................................................... 36
Performance and type ................................... 37
Lumibrite ....................................................... 38
Power Source ................................................ 39
Magnetic resistant performance .................... 41
Band .............................................................. 43
How to use the diver adjuster ........................ 45
How to use the diver extender ....................... 47
After sales service ......................................... 49
6 TROUBLESHOOTING
Setting the stopwatch hands (1/5-second and
minute hands) to the preliminary position ...... 51
Troubleshooting ............................................ 55
.................................... 58
Resetting the built-in IC .............................. 58
7 SPECIFICATIONS
Specifications ................................................ 60
EN
1
HOW TO USE
EN
4
Handling cautions
b WARNING
Please note that there is a risk of serious consequences such as severe injury if the following
safety regulations are not strictly observed.
Immediately stop wearing the watch in following cases:
○ If the watch body or band becomes edged by corrosion etc.
○ If the pins protrude from the band.
* Immediately consult the retailer from whom the watch was purchased or SEIKO CUSTOMER SERVICE
CENTER.
Keep the watch and accessories out of the reach of babies and children.
Care should be taken to prevent a baby or a child accidentally swallowing the accessories.
If a baby or child swallows the battery or accessories, immediately consult a doctor, as it will be
harmful to the health of the baby or child.
Do not remove the secondary battery from the watch.
* About the secondary battery → Power Source → P. 39
Replacement of the secondary battery requires professional knowledge and skill. Please ask the retailer
from whom the watch was purchased for replacement of the secondary battery.
Installation of an ordinary silver oxide battery can generate heat that can cause bursting and ignition.
6
Please note that there is a risk of minor injury or material damage if the following safety
b CAUTION
regulations are not strictly observed.
Avoid the following places for wearing or keeping the watch:
○ Places where volatile agents (cosmetics such as polish remover, bug repellent, thinners etc.) are
vaporizing
○ Places where the temperature drops below
5°C or rises above 35°C for a long time
○ Places affected by strong magnetism or static
electricity
If you observe any allergic symptoms or skin irritation
Stop wearing the watch immediately and consult a specialist such as a dermatologist or an allergist.
Other cautions
○ For adjusting the length of the metallic band, specialized knowledge and expertise are necessary.
Therefore, in such a case, contact the retailer from whom the watch was purchased. If you attempt
to adjust the metallic band, injury may occur to your hand or fingers, or parts of the band may be
lost.
○ Do not disassemble or tamper with the watch.
○ Keep the watch out of the reach of babies and children. Extra care should be taken to avoid risks
of any injury or allergic rash or itching that may be caused when they touch the watch.
○ If your watch is of the fob or pendant type, the strap or chain attached to the watch may damage
your clothes, or injure the hand, neck, or other parts of your body.
○ Places affected by strong vibrations
○ Places of high humidity
○ Dusty places
EN
EN
5
1
HOW TO USE
7
1
Precautions for diving (Please make sure to observe the following.)
HOW TO USE
b WARNING
Never use the watch, in saturation diving using helium gas.
b WARNING
While diving, never operate the watch in any other manner than set forth in the instruction
manual.
b WARNING
Before using the diver’s watch, you have to be properly trained in various types of diving and
possess the requisite experience and skill to dive safely. When diving, strictly abide by the
rules of diving.
b CAUTION
Please note that there is a risk of minor injury or material damage if the following safety
regulations are not strictly observed.
Do not turn or pull out the crown when the watch is wet.
Water may get inside of the watch.
* If the inner surface of the glass is clouded with condensation or water droplets appear
inside of the watch for a long time, the water resistant performance of the watch is
deteriorated. Immediately consult the retailer from whom the watch was purchased or
SEIKO CUSTOMER SERVICE CENTER.
Do not leave moisture, sweat and dirt on the watch for a long time.
Be aware of a risk that a water resistant watch may lessen its water resistant
performance because of deterioration of the adhesive on the glass or gasket.
Do not wear the watch while taking a bath or a sauna.
Steam, soap or some components of a hot spring may accelerate the deterioration
of water resistant performance of the watch.
1
HOW TO USE
EN
8
1
HOW TO USE
■ Before diving
Before diving, check the following:
* “Names of the parts and their functions” → P. 16
The time is correctly set.
1
The energy level is at least “half
2
full” and the small seconds
hand is moving every second.
If the small seconds hand is
moving every two seconds or
has stopped, expose the dial to
light to charge the watch.
* “Charging the battery” → P. 33
The rotating bezel turns
3
smoothly.
(The bezel rotation must not be
too loose or too tight.)
* “How to use the rotating bezel” → P. 20
EN
10
1
2
3
The crown and button screws
4
are firmly tightened.
* “Screw down crown” → P. 17
* “Screw lock type button” → P. 18
There are no visible cracks or
5
scratches on the crystal or
watch band.
The band is firmly attached to
6
the watch (with spring bars,
clamp or other parts.)
If there are any malfunctions, contact the retailer from whom the watch was purchased
or SEIKO CUSTOMER SERVICE CENTER.
5
b
CAUTION
6
4
EN
EN
9
HOW TO USE
11
1
■ While diving
1
HOW TO USE
Please observe the following cautions for use.
■ After diving
Please follow the care instructions below after diving.
1
HOW TO USE
The watch can be used for air diving within the water
resistant range displayed on the dial.
Take care not to bump the watch against hard
objects such as rocks.
EN
12
■ Structure of the case
1
In the following types of models, take care of the following issues in usage.
HOW TO USE
The bezel or protective outer case is securely fastened to the watch with setscrews.
Never loosen the setscrews.
Do not operate the crown or buttons underwater.
Bezel rotation may become slightly harder in the
water but this is not a malfunction.
setscrew setscrew
* The above illustration is provided as an example, therefore it may not be exactly the same as your watch.
b
CAUTION
Never loosen the setscrews used to fix the bezel or protective outer case.
Doing so may cause damage or result in further loosening.
* If you find that the setscrews have become loose or are functioning abnormally, consult the retailer from whom
the watch was purchased or SEIKO CUSTOMER SERVICE CENTER.
Rinse the watch in fresh water to wash out all seawater and wipe it thoroughly dry to prevent rust.
Avoid pouring running water onto the watch directly from a faucet. Put some water into a bowl first, and
then soak the watch in the water to wash it.
b
CAUTION
Depending on the environment where a diver’s watch is used, its inner parts or movement
as well as its case or band may be affected. We recommend that you have your watch
overhauled regularly once every 3 or 4 years.
Characteristics
This solar watch is equipped with a stopwatch function.
• A full-scale stopwatch, which can measure in 1/5-second increments with the center hand, is equipped.
• A solar cell under the dial converts any form of light into “electrical energy” to operate the watch.
* “Chronograph” means a watch with a stopwatch function.
■ Water resistant
performance for air diving...
■ Stopwatch function..................
→ P. 26
■ Solar charging function...........
→ P. 33
■ Energy level display function..
→ P. 35
This watch is equipped with water resistant performance to be used
in water for a long period of time with scuba diving tanks. (It cannot
be used for saturation diving that uses helium gas.)
The stopwatch can measure up to 60 minutes in 1/5-second
increments. After measuring 60 minutes, the stopwatch will
automatically stop.
The watch charges by converting light that shines on the solar panel
on the dial into electrical energy. After the battery is fully charged,
the watch will operate for about six months even if the dial is not
exposed to light.
The energy level is displayed on the “charge level display”.
EN
13
HOW TO USE
1
EN
14
EN
15
Stopwatch 1/5second hand
(center hand)
Hour hand
Small seconds
hand
Stopwatch
minute hand
(energy level
hand)
Rotating bezel
Minute hand
24-hour hand
Button A
Toggling to the
stopwatch display
Crown
Normal position
(not locked):
Stopwatch and
charging functions
First click position:
Date setting
Second click
position: Setting
the time, setting the
stopwatch hands
to preliminary
position, and
performing a
system reset
Button B
Toggling to the charge
level display
Date
1
HOW TO USE
Names of the parts and their functions
1
1
2
3
4
5
6
7
8
9
0
a
2
3
4
5
6
7
8
9
0
a
Screw down crown
The screw down crown features a mechanism that can securely lock the crown when it is not
•
•
•
being operated in order to prevent any operational errors and to improve its water resistant
performance.
It is necessary to unlock the screw down crown before operating it.
•
Once you have finished operating the crown, make sure to relock it.
•
To unlock the crown】
【
Turn the crown counterclockwise to unscrew it.
Now the crown can be operated.
Unlock the crown before
operating it.
Unscrew
* When locking the crown, turn it slowly with care, ensuring that the screw is properly engaged. Be careful not to
push it in forcefully, as doing so may damage the screw hole in the case.
Crown locked
【
To lock the crown】
Turn the crown clockwise while gently pressing it in
toward the watch body until it stops.
Crown unlocked
After operating the crown,
lock it.
Rotate while
pressing
the crown in.
1
HOW TO USE
EN
16
1
HOW TO USE
The screw lock type button features a mechanism that can securely lock the button when it is not
being operated in order to prevent any operational errors and to improve its water performance.
It is necessary to unlock the screw lock type button before operating it.
•
•
Once you have finished operating the button, make sure to relock it.
To unlock the button】
【
• Turn the button ring counterclockwise until it
stops.
• Now the button can be operated.
To lock the button】
【
• Turn the button ring clockwise until it stops.
• Now the button can no longer be operated.
* If the screw or button get dirty, they may not operate properly. “Daily care” → P. 36
* Note that if you turn the button ring more than you need to, the screw lock button may be difficult to return to its
original position.
* Before you go diving, check that both buttons are properly locked.
* Do not use the buttons when the watch is wet or when you are underwater.
EN
18
Screw lock type button
Button locked
(cannot be pressed)
Button unlocked
(can be pressed)
Button locked
(cannot be pressed)
Button unlocked
(can be pressed)
EN
Toggling between displays
The operation shown in the illustration below toggles between “charge level display” and
“stopwatch display”.
Toggling between the displays changes the function of the hands.
<Charge level display> <Stopwatch display>
Center hand
Button A
Energy level hand
* On the “charge level display”, press button A to toggle to the “stopwatch display” and simultaneously start the
stopwatch.
* While the stopwatch is operating, you cannot toggle the display. To return to the “charge level display”, first reset
the stopwatch.
During operation of the stopwatch, button B provides “split”, “split reset” and “reset” functions.
On resetting the stopwatch, the display automatically returns to “charge level display” after 1 minute.
Press and
release button A
Press and
release button B
Stopwatch 1/5-second hand
Button B
Stopwatch minute hand
EN
17
HOW TO USE
19
1
Loading...