Segway Ninebot Gokart Pro Quick Start Guide

EN

The assembled
GoKart Pro

(Ninebot Engine Speaker location)

Support rods

2 Installation of Accessories

Install the Rear Spoiler

Note: Do not press or lift the rear spoiler during installation.

a. Insert the rear spoiler bracket into the slot.

Quick Start Guide

Rear Spoiler

AA Battery
Compartment

b Use the 2.5 mm hex wrench to tighten the 6 screws into

the main body of the rear spoiler. (See Accessory No. 2).

a

L

R

b

Brake
(left)

Scan the QR code

above to watch the

Disassembly and

Riding Safety Video.

1 Adjustment

Stretch the frame and adjust the length
of the body

a With both hands holding the steering wheel and the

seat, stretch the frame out to a suitable position
along the horizontal direction of the connection
tube.

b Align the scalable structure of the frame with the

marking on the connection tube.

c Positioning: Use the short hex wrench to press the

two screws into the holes on the left and right

connection tube in order, as shown in the figure on

the right (The screw is set to a depth of about 1 cm

for successful position).

d Tighten the 4 screws.

3 Before the First Drive

For your safety, a new Gokart is inactivated. Please activate your Gokart via the App

before first use.

You can also find our app in the Apple App Store as well as the Google Play Store,
simply search "Segway-Ninebot"

Segway-Ninebot App

How to activate:

Install the App and register/log in.

1

d

a

b

c

Four screws are already
inserted into the screw holes.

Press the power button on the S-Max to turn on the Gokart Pro.

2

The Gokart will automatically power off when idle for 10 minutes.

Adjust the steering wheel height

Remove the speaker before adjusting the
height of the steering wheel.

a Raise the steering wheel to a suitable height.
b Insert the quick release screw into the hole of

the corresponding height.

（Insert the quick release screw into the hole of

the corresponding height.）

c Tighten the quick release nut.
d Press to fix the steering wheel quick-release

components.

e Ensure the steering wheel does not shake.

Otherwise, repeat the steps b, c, d, e.

4 Learning to Drive

You are at a risk of injury when driving a Gokart,
please dress properly as shown in the picture.

Minors must learn and drive under adult
supervision.

a

a

d

c

b

f

b

Correct dress code

Wear a helmet
Tie up long hair (if any)

Wear
protective
gear

Zip up the zipper

No long skirts

Install the Ninebot Engine Speaker

a Place the base in a proper position (as shown below) and

wrap the strap around the vehicle body and fasten the
strap.

base

a

c Align the holes on the bottom of the speaker. Press

down until you hear a "click" sound.

c

b Press the remaining part of the strap into

the storage slot.

b

Remove the Speaker：Press the disassembly

switch while lifting the speaker upward.

Indicator

3 4

Open the App, Click Vehicle > Search device to connect to your
Gokart Pro. The vehicle will beep when the connection is
successful. The Bluetooth icon will stop blinking and remain
illuminated.

Follow the instructions in the app to activate the
Gokart and complete the corresponding tutorial and
exercises.

Riding Safety

Ninebot Engine Speaker:

* The Speaker and the App cannot be connected to the Gokart at the same time. If you have connected the App,
disconnect the App from the Gokart first, confirm that the indicator light of the Gokart is flashing blue, and then pair the Speaker.

Vibrating

diaphragm

turn on

Indicator Volume +

Pause/Next

Wear flat shoes

1

Fastening the seat belt

Sitting on the seat, buckle the left and right parts of
the seat belt in front of you.

2

Driving

Acceleration: lightly press the throttle (right pedal)
to go forward.
Deceleration: lightly press the brake (left pedal) to

decelerate.

* Do not pump the brake pedal to decelerate.
Steering: steer the Gokart by slightly turning the
steering wheel clockwise or counterclockwise.

3

Reversing

When the Gokart is stopped, double-press the
brake (left pedal). After you hear a beep,
the Gokart has switched to reverse mode. Press
the throttle to drive the Gokart in reverse.
Double-press the brake (left pedal) again to
return to forward mode.

* For more information about the speaker, see the user manual of Ninebot Engine Speaker.

Ninebot S-Max Quick Start Guide

(Hereinafter referred to as S-Max)

1 Remove the S-Max body form the Gokart

Power off the Gokart before disassembly.

1. Rotate counter-clockwise

to unplug the power
extension cord.

5

Press the power switch to turn on the speaker.
Press and hold the Mode button to start pairing.

mode

Horn Power

2. Loosen the traps and take out

the S-Max body.

* If lifting the frame by yourself,

do not lift the backside more
than 19° or you may damage
the bumper.

Do not lift the Rear Spoiler.

switch

Volume -

Mode

USB Type-C

4

Emergency braking

In the event of a situation that requires an
emergency stop, pull the hand brake handle on
the right side of the Gokart to engage the
emergency brake.

* Only use the emergency brake when necessary.
Frequent use can deform the tire.

3. Remove the adaptor

pad of S-Max.

2 Assembling Your S-Max

Install the steering bar

1

Insert the steering bar into the S-Max body. Rotate the height adjustment knob

2

Tighten the two screws.

(See Accessories No. 3)

Adjust the knee pad height

1

counter-clockwise.

Lift the knee pads to the desired

2

height. Rotate the height adjustment
knob clockwise to tighten.

3 Before the First Ride

There are safety risks when learning to ride the S-Max. You must read the Safety Instructions and follow the New Rider Tutorial
in the App before your first ride.

For your safety, your S-Max is not activated at this time and will beep occasionally after Power ON.

Until activated, the S-Max maintains a very low riding speed and steering sensitivity. Install the App on your mobile device (with
Bluetooth 4.1 or above), connect to the S-Max with Bluetooth, and follow the App instructions to activate your S-Max and follow
the training procedures.
Scan the QR code to download the App (iOS 9.0 or above, Android™ 4.3 or above).

Segway-Ninebot App

1 2

Install the App and register/login.

Power ON the S-Max. The Bluetooth icon blinking indicates the S-Max
is waiting for a connection.

4 Warnings and Cautions

WARNING

Wear an approved helmet and other protective
gear to minimize any possible injury.

Sudden speed change and turns are forbidden during riding.

Rider can be seriously injured with such actions.
When the vehicle tilts back or sounds alarm, please slow down
immediately till the vehicle is back to the normal position.

FR

3

Put the cap on.

* Lift the guide bar to help steer the

S-Max without a rider when powered

on.

WARNING

DO NOT use to lift or carry the S-Max.

Click Vehicle > Search device to connect to your S-Max. The S-Max

3 4

will beep when the connection is successful. The Bluetooth icon will
stop blinking and remain illuminated.

BEFORE RIDING, MAKE SURE TO SWITCH THE S-MAX TO
SELF-BLANCING MODE IN THE APP. Follow the prompts to watch the
Riding Safety video, complete the New Rider Tutorial, and then activate
the S-Max.

* When the mode is switched successfully, you will hear two beeps.

Basic info and settings

Gokart mode

Water contact with Li-ion battery can increase the risk of fire.

Do not expose the vehicle in the rain or ride it in the rain for a long
period of time. When the vehicle is not used, please store it in dry
and cool surrounding.

Charge the battery in time to avoid over-discharging and cause damage.

The standby time is around 120 to 180 days when the battery
is fully charged. Please charge the battery in time or
over-discharging may cause damage.