<DRAFT>
Seg-Link® User Manual
Congratulations on purchasing the Seg-Link kit. This document shows you how to set up,
install, and use the Seg-Link. To set up the hardware, see Hardware Setup. To install the
required software, see Driver Installation.
Kit contents are listed below. Make sure you have all listed parts before proceeding with the
installation and setup. If any part is missing or damaged, contact Segway Technical Support at
1-866-473-4929 or
Seg-Link unit; connect to a PC and a Segway
PT for troubleshooting.
t
echnicalsupport@segway.com.
6-ft USB cable; for connecting the Seg-Link to
your PC.
6-ft D-sub 9 cable; for connecting the Seg-Link
to a Segway PT.
Driver Installation and User Manual CD
XXXXX-XXXXX aa
Copyright © 2012 Segway Inc. All rights reserved.
1
Hardware Setup
1. Plug the USB cable into the Seg-Link. Plug
other end of cable into an open USB port
on the PC.
2. When a wired connection to the Segway
PT is desired, plug the D-sub 9 cable into
the Seg-Link, then plug the other end
of the cable onto the A and B service
connectors on the PT.
Plug in USB cable here
Plug in D-sub 9
cable here
Service
Connector B
Service
Connector A
XXXXX-XXXXX aa
Copyright © 2012 Segway Inc. All rights reserved.
2
Driver Installation
1. Ensure no other applications are running on your
computer. Insert the CD-ROM into the computer’s
drive. Locate and open the “setup.exe” file. At the
welcome screen, click “Next” to continue. Read
and accept the License Agreement by selecting “I
accept the agreement” and then clicking “Next.”
2. At the “Information” screen, read the important
installation information, then click “Next” to go
to the User Information screen. Type in your
User Name and Organization (dealer, distributor,
etc.), then click “Next”. At the “Select Destination
Location” screen choose where you would like the
drivers installed. We recommend choosing the
default folder – click “Next.”
3. Read the Important Note regarding red state LED
blinking cycle, then select “YES” and click “Next.”
At the “Select Components” screen, choose “Full
installation,” then click “Next.”
4. At the “Select Start Menu Folder” screen, choose
the default by clicking “Next.” At the “Select
Additional Tasks” screen, decide what optional
tasks you want performed during the installation,
then click “Next.”
XXXXX-XXXXX aa
Copyright © 2012 Segway Inc. All rights reserved.
3
Driver Installation (cont.)
5. Click “Install” and wait while the installation
program runs.
6. When the installation program is finished, you
should receive a message like the one at right. If
installation was successful, click “Finish.”
7. Read the important revision history information,
then click “Next.”
8. Select “Yes, restart the computer now,” then click
“Finish.” Your computer will restart.
XXXXX-XXXXX aa
Copyright © 2012 Segway Inc. All rights reserved.
4
Regulatory Compliance
United States
Radio Frequency Interference:
United States FCC Part 15 Class B Radio Frequency Interference
(RFI) Statement
The Seg-Link has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. The
Seg-Link generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the User
Materials, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
FCC Notice (for U.S. Customers):
This device complies with Part 15 of the FCC Rules:
Operation is subject to the following conditions:
1. This device many not cause harmful interference, and
2. This device must accept any interference received, Including interference that may cause undesired operation.
Changes and Modifications not expressly approved by Segway Inc. may void your authority to operate this equipment under
Federal Communications Commissions rules.
FCC ID: T2Z-GC261515
IC: 6395A-GC261515
Canada
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
The Seg-Link is a Class B digital apparatus that complies with Canadian ICES-003.
Europe
The Seg-Link complies with the requirements of the European Directives 89/336/EEC, Directive of Electromagnetic
Compatibility.
WEEE (Waste Electrical and Electronic Equipment)
This product should be recycled at the end of its useful life.
All Segway Battery Chargers can be returned to the location
where they were purchased, or to Segway Inc. at:
Segway Inc.
Attn. Product Recycling
14 Technology Dr.
Bedford, NH 03310
USA
To find the nearest Segway dealer or distributor, visit www.segway.com/locator/.
XXXXX-XXXXX aa
Copyright © 2012 Segway Inc. All rights reserved.
5
Loading...