Segway eMoped C80 User Manual

Las baterías de iones de litio o los productos que contienen dichas baterías

ADVERTENCIA Propuesta 65 de California

pueden dejarlo expuesto a sustancias químicas como cobalto, litio, óxido de

níquel y níquel, las cuales reconoce el estado de California como causantes

de cáncer y malformaciones congénitas u otros daños reproductivos.

Para obtener más información, visite el sitio web www.P65Warnings.ca.gov

Este producto solo puede usarse en áreas que cumplan con la regulación federal 16 CFR PARTE 1512. El fabricante se reserva el derecho a modiﬁcar el producto y actualizar este manual en cualquier momento. Los parámetros del producto varían en modelos diferentes. Están sujetos a cambios sin previa notiﬁcación.

Visite el sitio web www.segway.com para descargar los últimos materiales de usuario.

CE.00.0020.57-B

Segway eMoped C80

User Manual

Please read the User Manual carefully before use and keep it for future reference.

Do not ride until you know the proper operation of this product.

Contents

Welcome

1. Riding Safety

2. Product Overview

3. Parts and Functions

4. Activate the Vehicle

5. How to Charge

6. How to Install the Battery

7. Learn to Ride

8. Warnings and Cautions

9. Maintenance

10. Speciﬁcations

11. Certiﬁcations

12. Trademarks and Legal Statement

Appendix: Installation of the Rear-view Mirrors

Thank you for choosing Segway eMoped C80!

Combining advanced wireless positioning technology and smart App control, Segway eMoped C80

promises a brand-new riding experience, which is safe, intelligent, and also brings out the rider’s

personality.

Original instructions

The pictures shown are for illustration purpose only. Actual product may vary.

1. Riding Safety

Please beware that you risk injury from loss of control, collisions, and falls whenever you ride the device. To reduce the risk, you must read and follow all “CAUTION” and “ WARNING” notices. Please understand that you can reduce the risk by following the instructions and warnings in this manual, but you cannot eliminate all the risks. Please use common sense when riding.

● It is the rider’s responsibility to follow local laws and regulations and abide by relevant laws and traﬃc regulations. ONLY ride on the roads as permitted by law.

● In order to master riding skills, the rider needs to practice. Use with caution since skill is required to avoid falls or collisions causing injury to the user or third parties. To avoid injuries, DO NOT allow people who don’t know the proper operation to ride the product. Neither Ninebot (Ninebot (Beijing) Tech Co., Ltd. and its subsidiaries and aﬃliates) nor Segway (Segway Inc. and its subsidiaries and aﬃliates) is responsible for any injuries, damages or legal disputes caused by a rider's inexperience or failure to follow the instructions in this manual.

● For your safety, please DO NOT modify the product or change parts by yourself. Use only Segway approved parts and accessories. Modiﬁcations to the product could interfere with its operations, result in serious injury and/or damage, or void the Limited Warranty.

● If the product makes an abnormal sound or signals an alarm, stop riding immediately.

● DO NOT allow anyone to ride the product on his/her own unless he/she has carefully read this manual.

Assist new riders until they are comfortable with the basic operation of Segway eMoped C80.

● DO NOT park Segway eMoped C80 in no-parking zones, such as an emergency exit, building lobbies or ﬁre escapes.

● Do not charge or park the product in residential buildings. Keep away from combustible materials when charging, and disconnect from the power supply once it’s fully charged.

Riding Surfaces and Environment:

● Slow down when riding in complicated road conditions. Riding at a high speed to cross over obstacles, on uneven ground, slippery surfaces, loose ground, steep slope or at sharp turns, can lead to falls, collisions or even death.

● DO NOT ride in bad weather such as heavy rain or storm. When riding in rainy or snowy weather, the traction is reduced and the braking distance is increased. For your safety, please drive slower and brake earlier to reduce the risks for loss of control and falls.

Who Should Not Ride:

People in the following groups should not ride Segway eMoped C80: I. Anyone under the influence of alcohol, drugs, or intoxicants.

01 02

II. Anyone who suﬀers from diseases that put them at risk if they engage in strenuous physical activity. III. Anyone whose age and weight is outside the stated limits (See Speciﬁcations). IV. People who are extremely tired.

Preparations before Riding:

● Make sure there are no loose fasteners and damaged parts.

● Check the status of the power supply circuit, lighting, dashboard display, etc. and make sure they work

normally.

● The front and rear brakes should function properly and the brake cables should be in good condition.

● Make sure the handlebar is stable, and that the front and rear wheels are not shaky or loose.

● Make sure the reflectors are not damaged or dirty.

● The rider must wear a helmet and other protective gear.

● DO NOT carry heavy cargo.

● When the battery is low (the dashboard shows less than two bars), please use the original charger to

charge immediately.

● Ensure normal tire pressure, with front tire 26 psi (180 kPa) and rear tire 32 psi (220 kPa). Make sure the tire tread is intact.

WARNING

Always wear a helmet when riding. Use an approved helmet that ﬁts properly with the chin strap in place, and provides protection for the back of your head.

Instructions on Riding and Usage:

● DO NOT accelerate or brake abruptly when riding.

● Please hold the handlebar with both hands to avoid serious injuries due to loss of balance or falling.

● Stay alert and ride defensively. Always keep a safe distance from other vehicles. Slow down when

entering a new environment.

● DO NOT use a cell phone, camera, headphones, earbuds or perform any other activities while riding.

● Slow down when approaching intersections, motorways, corners, doors, etc. Yield the right of way for

pedestrians, bicycles and motor vehicles.

● If any abnormality occurs, stop riding immediately and contact the after-sales service in time. DO NOT ride before the cause of the abnormality is found out and repaired.

● Always park Segway eMoped C80 on a flat surface. Otherwise, the vehicle may slip and cause harm.

● ONLY use the original charger. Allow the vehicle to stay still for a while before charging. Do not attempt

to charge your vehicle if it, the charger, or the power outlet is wet.

2. Product Overview

Spare Key

Segway eMoped C80

Accessories

Limited Warranty × 1

Limited Warranty

Disclaimer Card × 1

User Manual × 1 Quick Start Guide × 1

User Manual

NFC Card × 2

Quick Start Guide

Spare Key × 2

Charger × 1

Rear-view Mirrors

The key can open the trunk when the Electric Trunk Lock cannot work (such as when the battery is not in the vehicle or the battery is empty). For the convenience of use, please keep one key in the slot on the battery and the other key on the charger cable.

Battery Charger cable

Before riding for the first time, use the key to open the trunk and connect the battery power plug. Make sure the Handlebar Lock switch is pressed down.

Battery power plug

Disclaimer Card

03 04

NFC Card

Handlebar Lock switch

3. Parts and Functions

Riding status ring

Brake oil container

Custom button

Rear brake lever

Front reflector

Front brake lever

Saddle

Horn button

Throttle

USB port

Headlight

Centered damper

Tail light

Foot deck

Side reflector

Nameplate

Riding Status Ring Colors and Meanings

Footrest

Frame No.

Functions of the Custom Button

Rear reflector

Rear fender

【open the trunk】【activate/ cancel Cruise mode】【power ON/OFF】

ON/OFF

Green: Ready to go

Blue Power assist mode Cruise mode

*You can enable and disable the Power assist mode via the Segway-Ninebot App.

Squeeze one brake lever and

Press the button when riding.

press the button.

Orange: Standby, unable to ride Red: Error

05 06

When your phone gets into range and the owner identity is veriﬁed,

press and hold the button.

4. Activate the Vehicle

Vehicle Fans Moments MeDiscover

Error code display

Speed display

An eMoped C80 that has not been activated is limited to 6.2mph (10 km/h) and the AirLock does not work.

To enjoy the full functionality of the vehicle, please scan the QR code to download the Segway-Ninebot App (hereinafter referred to as the App) and ﬁnish the New Rider Tutorial. Alternatively, go to the Google Play Store (Android) or the Apple App Store (iOS) and

E (battery is empty)

Photosensitive sensor

Segway-Ninebot App

search for "Segway" or "Ninebot" to download and install the App. To ensure Bluetooth communication, keep your phone close to the vehicle during the activation process.

F (battery is full)

Phone connection

1 Install the App, register and log in. 2

Power on Segway eMoped C80 (see details on page 11). A flashing phone connection indicator means the vehicle is waiting for a connection.

Dashboard

Rear bracket

Vehicle charging port

Front damper

Riding pedal

Click 'Search vehicle' to connect to your Segway

Front wheel

（Reflective tire）

Rear wheel

（Reflective tire）

eMoped C80. The Bluetooth signal will stop flashing when the connection is successful.

Kickstand

Follow the instructions to activate your vehicle and complete the New Rider Tutorial. The speed limit

would now be lifted within the local legal bracket and the Airlock could be activated via the app.

07 08

Vehicle charging port

5. How to Charge

The battery level may be low or empty during transportation and storage. You can charge in any one of the methods below. Remember to unplug from the power supply once fully charged.

Charge the Vehicle

Connect the battery power plug, then close the trunk. Connect the charger output to the vehicle charging port, and then connect to the power outlet.

Internal Charging

Connect the charger output to the battery charging port, plug into the power outlet, and then close the trunk.

Charge the Battery

Open the trunk and take out the battery. Connect the charger output to the battery charging port, and then connect to the power outlet.

WARNING

● ONLY use the original charger. Other types can burst and catch ﬁre.

● DO NOT charge if the battery is wet or damaged.

● DO NOT connect the charger when the charging port or charging cable is wet.

6. How to Install the Battery

After charging the battery, please put it into the vehicle in the following steps:

Open the trunk by any of the following methods.

Use the key.

If the battery is in the vehicle, squeeze one brake lever and hold the custom button. If the battery is not in, press and hold the custom button, wait until the E, F, as well as the phone connection signal light up, and then squeeze one brake lever while holding the custom button.

Please enable the AirLock in the App in advance. Make sure the ECU battery is not empty. You can check the battery level in the App.

Put the battery in the vehicle, connect the battery power plug and close the trunk.

Squeeze one brake lever and tap the NFC card on the dashboard.

*The charger indicator is red when charging and turns to solid green when fully charged.

If the temperature of the vehicle body exceeds 104°F (40°C), it cannot be charged normally. Please wait for the temperature to drop.

09 10

7. Learn to Ride

Riding

Kick up the kickstand, sit down on the saddle and support yourself with both feet. Gently turn the throttle inward to start your trip.

NOTE:

Before the rider is seated, the status rings are orange and the throttle cannot be started. If the rider leaves the seat during riding, an alarm will start, and the throttle will not work.

Locking

WARNING

Always wear a helmet and other protective gear to minimize any possible injury in the learning process. Always abide by local laws and traﬃc rules.

Power on

The vehicle can be powered on in one of the following ways:

Tap the NFC card on the dashboard. You will hear a beep when the vehicle is powered on successfully.

Enable the AirLock in the App. The vehicle will power on when you sit on the saddle, or press and hold the custom button.

Release the throttle and hold the front and rear brake levers with appropriate force. After the vehicle has stopped, support it with the kickstand. You can lock your Segway eMoped C80 in the following ways:

Auto lock Enable the 'Auto lock' feature in the App. When you walk away with the phone, the vehicle will lock automatically. Press and hold the custom button. Tap the NFC card.

NOTE:

After locking, please turn the handlebar to its left end to ensure that the Handlebar Lock is activated. The control switch of the Handlebar Lock is located inside the trunk. You can operate the switch to enable/disable the lock.

Anti-theft Alarm

After Segway eMoped C80 is locked, if there is abnormal movement, the status rings will flash in red and green and a continuous alarm will start.

11 12

8. Warnings and Cautions

Please avoid all dangerous riding behaviors!

DO NOT drive under the influence!

Slow

When riding on the road, always obey traﬃc rules, local laws and regulations. When riding oﬀ-road, slow down, watch for changing road conditions and avoid possible hazards.

Slow

Make sure the headlight is on when driving at night.

13 14

Overload

NEVER hitch a ride with another vehicle.

Slow

Please drive slowly and carefully in complicated road conditions.

Overload

DO NOT carry heavy objects or passengers.

9. Maintenance

Cleaning

Clean with water, neutral detergent and a soft cloth.

CAUTION

DO NOT clean with alcohol, gasoline, acetone, or other corrosive/volatile solvents. These substances may damage the appearance and internal structure of your vehicle. DO NOT wash with a power washer or hose.

Slow

DO NOT ride in bad weather such as heavy rain and snow.

Slow down before making a turn. Use caution when riding and DO NOT make sharp or sudden turns.

15 16

Hold the handlebar with both hands. No speeding.

DO NOT use mobile phones, cameras, headphones, earplugs, etc. when driving.

DO NOT rub with sandpaper or metal brush.

WARNING

Before cleaning, make sure the vehicle is powered oﬀ.

Storage

Store in a dry and cool place indoors and avoid sunlight and rain, so as not to rust parts and shorten the service life. Disconnect the battery power plug for long-time storage to prevent over-discharge.

Motor

1. When riding in wet conditions, the water level should not exceed the central axis of the rear wheel.

2. Regularly check the motor connectors (the hub motor is in the rear wheel). If the nuts and bolts are loose,

tighten immediately.

3. Clean the vehicle after each ride to prevent particles from entering the motor and aﬀecting its normal use.

Do not spray water directly when cleaning.

4. Check whether the motor leads are scratched and whether there is abnormal noise when the motor is

running.

Motor controller

Check the connector regularly at an authorized service center to ensure that it is fastened.

Battery

1. DO NOT drain the battery. It is recommended to keep the battery level above 15%. Charge after each ride

to prolong the service life of the battery.

2. It is strictly prohibited to disassemble the battery. There is a danger of electric shock, short circuit, ﬁre,

explosion, etc.

3. When the battery indicator bars are all lit up or the charger indicator turns green, it means the battery is

fully charged.

4. The storage temperature for the battery is 32–95°F (0–35°C).

5. If you are not going to use the vehicle for a long time, take out the battery after it is fully charged,

place in a dry and well-ventilated place, and charge it every two months.

6. DO NOT store the battery in a place where there is a risk of falling. Falling may cause battery damage,

short circuit, ﬁre and explosion.

WARNING

DO NOT disassemble the battery. For information about the recycling and disposal of the battery and electrical waste, please contact your household waste disposal service, your local or regional waste management oﬃce, or your point-of-sale.

WARNING

- Risk of Fire - No User Serviceable Parts

AVERTISSEMENT

- Risque d'incendie - Aucune des pièces ne peut être réparée par l'utilisateur.

Charger

● Before charging:

1. The charger should ONLY be used to charge the original vehicle/battery. It is strictly prohibited to charge non-rechargeable batteries.

2. To prevent the electronic components inside the charger from loosening, DO NOT carry the charger in the vehicle.

3. The power supply voltage should be 100–240V AC.

4. DO NOT use when there are broken cables or loose connectors.

● During charging:

1. Place the vehicle in a safe place away from rain and sun exposure.

2. Connect to the battery or vehicle charging port ﬁrst, and then plug into the power supply.

3. When there is an abnormal smell, sound or light display, stop charging immediately and contact after-sales service.

● After charging:

1. When the battery is full, disconnect from the power outlet ﬁrst and then unplug the charger plug.

2. After the charger cools down, place it in a safe place inaccessible to children.

WARNING

1. Ensure good ventilation during charging. Stay away from ﬁre or explosive materials!

2. High voltage in the charger! DO NOT disassemble or replace parts of the charger.

3. DO NOT connect the charger to the power outlet for a long time. Unplug from the power outlet when not charging. DO NOT use the charger to charger multiple vehicles.

4. The charger should be handled with care. Keep away from outdoor elements such as rain and heat.

NOTICE: INSURANCE YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, PLEASE CONTACT YOUR INSURANCE COMPANY OR AGENT.

17 18

Maintenance Guideline

1. Perform the ﬁrst maintenance after 621 miles (1,000 km) mileage or riding for 3 months.

2. After the ﬁrst maintenance, it is recommended to maintain your vehicle every 1243 miles (2,000 km) or riding for 6 months.

Specific maintenance schedule and items:

Maintenance items

Adjustment or replacement of front and rear brakes

Handlebar steering check

Tire pressure check

Disc brake system check

Fastening components

Lubrication

Adjustment of the dampers

Lighting system check

Bearing adjustment

Wheel adjustment

Reflector check

Riding time (month)

Total mileage (km)

1000

A: Adjust C: Check L: Lubricate T: Tighten R: Replace

3000

A/R

L A

5000

7000

A/R

9000

11000

A/R

Maintenance instructions:

At the time of purchasing The 3rd month, or 621 miles (1000 km) The 9th month, or 1864 miles (3000 km)

The product is comprehensively inspected before shipping from the factory. Before use, the handlebar, front brake, rear brake, tire pressure and lighting system need to be fully inspected again.

Some parts may be worn at this stage. Fastening of major components, brake system inspection, and tire inspection, etc. are the main maintenance items.

At this stage, spare parts need to be inspected. The fastening of spare parts, brake system inspection, tire inspection, etc. are the main maintenance items.

10. Specifications

Vehicle parameters

Battery pack

Motor

Charger

Motor controller

Items

Vehicle dimensions: length × width × height Net weight Nominal payload Max. payload Rider age Wheelbase Ground clearance Max. speed Typical range

[1]

[2]

Power consumption per 100 km Traversable terrain Operating temperature Storage temperature Charging temperature IP ratings Battery type Rated capacity Rated energy Charging time Nominal voltage Motor type Peak motor power Nominal motor power

[3]

Rated rotating speed Input voltage Output voltage Output current Undervoltage protection value Overcurrent protection value

C80

62.6 × 28.3 × 40.0 in (1589 × 720 × 1016 mm)

121.3 lbs (55.0 kg) 165 lbs (75 kg) 220 lbs (100 kg) ≥ 16 years old

45.3 in (1150 mm)

5.1 in (130 mm) Close to, but less than 20 mph (32 km/h) 47 mi (75 km)

1.6 kW·h Paved road 0–133°F (-18–45°C)

-4–122°F (-20–50°C); 50–86°F (10–30°C) recommended 36–104°F (2–40°C); 50–95°F (10–35°C) recommended Vehicle: IPX5; Battery pack: IP67 Lithium-ion battery 24 Ah 1152 Wh About 7 hours 48 V Permanent magnet motor Close to, but less than 750 W Approx. 600 W 350 r/min 100–240 V AC

55.6 V DC 4 A 42 V 30 A

Others

Items

Tire Shock absorption Front brake Rear brake Handle grip material

C80

14 × 2. 50 vacuum tire (with circular reflector) Centered twin-tube dampers Disc brake Drum brake + energy recovery brake/EABS PVC

[1] The maximum speed on a paved level surface, when powered solely by such a motor while ridden by an operator

who weighs 170 lbs (77 kg), is less than

20 mph (32 km/h).

[2] Typical Range: The accumulated range of the vehicle was tested while riding with full battery, 165 lbs (75 kg) load,

77 °F (25 °C), wind speed ≤3 m/s, 12 mph (20 km/h) on average on paved road.

* Some of the factors that aﬀect range include: rider weight, number of starts and stops, ambient temperature, etc.

[3] The peak motor power functions at a lower wattage than 750 and the Nominal motor power functions at around

600 wattage, the actual power may be aﬀected by factors such as temperature, terrain and the rider.

19 20

Error Codes, Failures and Solutions

11. Certifications

Errors and failures

Error code 11 Error code 36

Error code 37

Error code 41

Error code 10, 12-30, 33-34, 38-40, 42

The vehicle has no power

Short range

Other failures

Smart service ( AirLock, SOS alert, OTA upgrade, GPS positioning, auto vehicle checkup, riding record, etc.) is not available.

Possible causes

Motor controller/battery undervoltage Weak signal in the ECU

Low battery in the ECU

The handlebar lock pin is not in place

Vehicle abnormality

The battery connection is not in place

Blown fuse

Insuﬃcient tire pressure

Insuﬃcient battery or charger failure

Frequent starts and stops, overloading

Battery failure Issues that cannot be resolved by the

user or when the problem is unknown.

1. The smart service fee is not renewed or the SIM card within the ECU has expired.

2. ECU failure

Solutions

Try charging the battery.

Please park the vehicle in an open space. Leave the charged battery in the vehicle

for more than 5 hours.

Turn oﬀ the vehicle, turn the handlebar to ﬁx the jamming, and then restart.

Please contact after-sales service or a designated repair center.

Please make sure the battery power plug is connected properly.

Replace the fuse.

Check the tire pressure: front tire 26 psi (180 kPa) and rear tire 32 psi (220 kPa).

Check the charger and fully charge the battery. Maintain good riding habits and DO NOT

exceed the payload.

Please contact after-sales service or a designated repair center.

Renew the smart service fee in 'After-sales

1. Service' in the Segway-Ninebot App.

2. Change the ECU.

This product complies with 16 CFR PART 1512:2019 The battery complies with UN/DOT 38.3. The battery complies with ANSI/UL 2271.

Federal Communications Commission (FCC) Compliance Statement for USA

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is

connected.

— Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Industry Canada (IC) Compliance Statement for Canada

This device complies with Industry Canada license-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

21 22

CAN ICES-3 (B)/NMB-3(B)

“

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement."

Neither Segway Inc. nor Ninebot is responsible for any changes or modiﬁcations not expressly approved by Segway Inc. or Ninebot. Such modiﬁcations could void the user's authority to operate the equipment.

Contains FCC ID: XMR201909EC25AFX IC: 10224A-2019EC25AFX FCC ID: 2AU2Y-JH0001 IC: 25633-JH0001

12. Trademark and Legal Statement

Segway and the Rider Design are the registered trademarks of Segway Inc., Ninebot is the registered trademark of Ninebot (Tianjin) Tech Co., Ltd; Bluetooth is the registered trademark of BLUETOOTH SIG,INC.; Android, Google Play are trademarks of Google Inc., App Store is a service mark of Apple Inc., The respective owners reserve the rights of their trademarks referred to in this manual. We have attempted to include descriptions and instructions for all the functions of the Segway eMoped C80 at the time of printing. However, due to constant improvement of product features and changes of design, your eMoped may diﬀer slightly from the one shown in this document. Please visit the Apple App Store (iOS) or Google Play Store (Android) to download and install the App. and visit www.segway.com to download the latest user materials. Please note that there are multiple Segway and Ninebot models with diﬀerent functions, and some of the functions mentioned herein may not be applicable to your unit. The manufacturer reserves the right to change the design and functionality of the Segway eMoped C80 product and documentation without prior notice. © 2021 Ninebot (Beijing) Tech Co., Ltd. All rights reserved.

23 24

IMPORTANT: The user shall agree to read the entire user manual and fully understand its content (especially the parts related to warnings and caution statements) and adhere to the instructions herein before riding this product. Be aware, this product is an electronic bike that is very diﬀerent from

a traditional man powered bicycle.

1. This product can be dangerous to a user, other persons and property in proximity thereto. The user shall assume all the risks and loss in connection with the product (especially for those related to and/or arising out of violation of the instructions about warnings and caution statements). Such risks include but not limited to loss of control, failure of the product and/or collusion) The consequences for such incident can be severe, including but not limited to injuries, bodily injuries, death and/or damages to property. SEGWAY and its affiliates shall not be liable for any claim, liability and loss related to

such consequences, if it is due to the user's assumption of risk.

2. The product is a means for transportation and the user may not have necessary and suﬃcient experience and skills to ride it, especially in complex environments and/or undesirable road and/or traﬃc conditions. Such risk may increase if the user has physical and/or mental impairment or disability, or a user is under the influence of alcohol, drugs or similar substance. Such risk may also increase if the user is not suﬃciently familiar with the functions, features and performance of the product. Thus, the user, especially new users, shall learn and practice how to ride this product properly and safely. Experience accumulated by practice would normally enable a user to better ride and operate the product by time.

3. The parts and components of the product are subject to fatigue, wear and tear ("Wear and Tear"). Many factors, such as environment, aging road conditions and/or riding behaviors may aﬀect the rate of Wear and Tear. Wear and Tear may cause unanticipated and/or sudden failure of the product, which may cause, inter alia, severe bodily injury or even death. So, the user shall regularly and periodically, as the circumstance requires, inspect and maintain the product. The user shall also conduct reasonable examination and inspection of the product every time before riding it. For instance, every time before riding the product, the user shall check and examine tire performance, battery level, brake (including brake cable and that the brake shall have proper tension), vehicle installation status and all functional parts. If abnormality, discoloration or change of color of material (especially in an area that receives high stress when the product is in motion or junction), scratch, crack, loose fasteners, and/or missing parts (such as screw, bolts and/or nut) which strongly indicates that it is not safe to ride the product.

4. Since it is impossible to predict and/or anticipate all and every scenario, condition and/or circumstances under which a product user may be exposed to risk and danger, the User Manual is not intended to be an exhaustive list on how to ride the product safely and/or avoid hazards related to the product. So, in addition to adhere to the instructions, the user shall also ride and/or use the product with responsibility, carefulness, precaution and best judgment. The user should always be a responsible rider, cautious, maintain proper speed and avoid all dangerous riding behaviors, as well as

traﬃc and/or

+ 32 hidden pages

Segway eMoped C80 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual