SEGI REH300 2WLR User Manual
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION:
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate this device.
IC
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
To reprogram your remote first cycle
the key in the ignition 5 times within
7 seconds. Parking lights will flash.
After that tap the Lock button on your
remote. Repeat for any additional
remotes. If you receive two parking
light flashes, your system has exited
remote programming mode and you
must retry.
QUICK START CARD
8102REUCL001200 // FT-1B2W Guide REV1
2 WAY 1 BUTTON REMOTES
Tap this button for 1 second to lock your doors and/or arm your vehicle.
Upon confirmation, the Lock LED will flash and remote will chirp once.
Tap this button twice within 1 second to unlock your doors and/or disarm your
vehicle. Upon confirmation, the Unlock LED will flash and remote will chirp twice.
Hold this button for 3 seconds to start your vehicle. Your vehicle’s parking
lights will flash once and/or siren will chirp once for confirmation. Upon
confirmation, the Start LED will flash and remote chirp once. It will then chirp
three times to confirm your vehicle has started. Repeat and your vehicle will
shut off.
Valet Mode: If your remote start is not working, you may be in Valet Mode. Your parking
lights will also not flash. Your doors will still lock and unlock. To exit Valet Mode,turn the
vehicle’s ignition On and then tap this button 5 times, waiting a second between each
tap. Your vehicle will flash the parking lights twice and exit Valet Mode. You can also
exit Valet Mode by turning the ignition On and then tapping the foot brake 10 times or
reprogramming your remote(s).
Firstech, LLC. | 1
2W1B_QuickCard 130827.indd 1 2013/8/27 19:04:18
QUICK START CARD
EVENT LEDS
Runtime Remaining: 100% Red
Runtime Remaining: 50% Red
Runtime Remaining: 25% Red
Runtime Remaining: 60 Sec Red
Lock Confirmation Blue 1 x 1 x
Unlock Confirmation Blue 2 x 2 x
Start/Stop Confirmation Blue
All Error Confirmations Red
Arming/Locking While
Trigger is Open
Low Battery Warning Blue Fade
LED
COLOR
Red
LED
DURATION
Once Every
5 Seconds
Once Every 2
Seconds
Once On/
Twice Off
3 Times 3 Times
REMOTE
CHIRPS
Once On/
Twice Off
3 Times
2 WAY 1 BUTTON REMOTES
START ERROR CODESLEDS
PARKING LIGHT FLASHES REMOTE START ERROR
3 then 1 1: Motor running
3 then 2 2: Key in ignition on position
3 then 3
3 then 4 4: Trunk open
3 then 5 5: Foot brake on
3 then 6 6: Hood open
3 then 7
3 then 8 8: Tach or voltage sensing failure
3 then 9 9: FT-DAS sensor shutdown
3 then 10 10: System is in Valet Mode
3: Door open
(manual transmission only)
7: Reservation off
(manual transmission only)
Questions/comments? Contact us at 888-820-3690 from 8 AM
to 5 PM PST. Also please visit www.compustar.com for a complete
Register online at www.compustar.com within 10 days of
purchase to activate your new remote’s warranty.
user’s manual.
Firstech, LLC. | 2
2W1B_QuickCard 130827.indd 2 2013/8/27 19:04:19
Loading...