SEGI JA1000 2WSSL3 Users manual

2-WAY REMOTE STARTING SYSTEM

WITH 1 BUTTONS

FOR AUTOMATIC TRANSMISSION

RED301-2WAY / MA1000-2WAY3

User Guide For Key

WARNING

It is the responsibility of the vehicle operator to ensure that their vehicle is parked in a safe and responsible manner.

1. When leaving the vehicle, it is the user’s responsibility to ensure that the gearshift lever is in “Park” in order to

avoid accidents upon remote starting. (Note: Make sure that the automatic vehicle cannot start in “Drive”.)

2. It is the user’s responsibility to ensure that the remote starter is disabled or put into valet mode before servicing.

FCC COMPLIANCE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void

user’ s authority to operate this device.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two

conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)

l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en

compromettre le fonctionnement.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Using the remote control

Description of Remote Appearance

2Way Remote 1Way Remote

Button Functions

Button

Press buttons for

LED

Function

Press 1time Lock

Press 2 times

Press 2times x 2

Unlock driver’s door

Unlock all doors

2 seconds Remote start/stop

Note: You make sure press button only after LED lighting ends to activate each feature properly.

Lock, Unlock and Remote

Starting icon is displaying with

Two LED color.

START/STOP:

Note : Remote Engine Start -

Press the button 1 time and then,

within 3 seconds, press and hold

the button for 2 seconds

Remote Engine Stop - Press

the button for 2 seconds

Lock/Unlock

Note: Press the button 1 time on the

remote control transmitter to lock the

vehicle. Press the button 2 times to

unlock the driver’s door, 2 additional

times to unlock all doors.

Lock, Unlock and Remote

Starting icon is displaying with

One LED color.

Vehicle Presets

Heater

When leaving the vehicle it is recommended to preset the accessory controls in preparation for the Next remote start. Settings for the blower motor(fan),front and rear (if

equipped),should not be left on HIGH. It is recommended to leave the settings on LOW or MEDIUM instead.

Windshield Wipers, Headlights

Certain vehicles require the windshield wipers and headlights circuits to become energized while running under remote start. When leaving the vehicle you must ensure that

the windshield wipers and headlights switches are OFF. Leaving the headlights switch ON on certain types of vehicles could cause them to remain ON even after remote

starter shutdown, resulting in a dead battery.

Leave Windshield Wipers off to avoid damage wipers/motor with remote start.

Changing the Remote Control Transmitter Battery

Remote transmitter should be provided with two 3-volt lithium battery (Model: CR-2025).

Please pay attention that with low battery LED in the remote might not work and the remote start distance might get shorter.

Batteries can be purchased at any electronic device stores.

Following the instructions below to change the remote control battery

1. You may use a coin to pry the remote control halves apart

2. Remove the old battery and replace with a new one

3. Be sure to observe the (+) sign when inserting the new battery.

4. Before assembling transmitter case, you should test the remote control.