Seeworld S708 User Manual

Please read the manual carefully before use the
GPS Tracker so that you can install the device
correctly and activate it quickly on the internet. The
outlook and true color are subject to the actual product.

GPS Vehicle Tracker

(GPS+GSM+GPRS)

SEEWORLD S708

User Manual

1.Technical parameter

1）.GSM：850/900/1800/1900MHz
2）.GPRS：Class12,TCP/IP

3）. Working Voltage：9-36V DC

4）. Working current：≈22mA (12vDC)

5）.

Working current

：≈12mA (24vDC)

6）.GPS

locating time：Cold start

≈38s（Open sky）

Warm start

≈32s

Hot start

≈2s（Open sky）

7）.GPS Precision：10m（2D RM）

8）. Working temperature：-20℃～+70℃

9）. Working humidity：20%～80%RH

10）. Measurement：71（L）×49（W）×24（H）mm

2.Out look

3. Device status indicators

3.1 The yellow-green LED behind（GPS signal state）

GPS signal is normal,

yellow-green

LED light long bright. No GPS

signal, the yellow-green LED flashes.

3.2 The blue LED in the front（GSM signal state）
GSM signal is normal，blue LED light long bright。No GSM signal,the blue
LED flashes。
GSM n

o signal, flashes（0.2 sec/2 sec），Signal normal long bright;

All LEDS will turn off after 5 minutes. When there is a new call orthe power is
connected, the LEDs willrelight and turnoff 5 minuteslater.

4. GSM card Installation

4.1 Preparation for the installation

4.1.1 Product Check. Open the packing box and check the device‘s model and

accessories. If the model is wrong or the accessories not complete, please contact

the dealer.

4.1.2 Choose SIM card. Please insert a SIM card to the device. Please take dealer’s

advice as reference.

4.1.3 GSM installation, use a toothpick or tweezers to hold the GSM slot

switch (yellow button),then the GSM slot will pop up.Put the GSM card into
the slot (metal side up) ,then replace the installed GSM slot (pictures as

shown below)

4.1.4 At this point can be connected to external 9-36 v power supply

Note: don't install backwards the terminal GSM card

The GSM card must be with GSM function and enough deposit.

If your GSM card need input PIN when power on, please referr your

phone's user manual and cancel it.

5. How to find the car's OBD connector locations

connect the devices to the car OBD interface, as shown below:

6.The Device Working

6.1 Power on: the device will be power on when connecting to the current. Then the

green-yellow LED indicators will light continuously. (SIM work normal) The

device will upload the location data to the online platform (the default interval of

uploadingdata is10seconds).When the car isin static state for a long time, the
device will be in energysaving modeandit will bemore smartand precise.

6.2 Power off：Pulloffthe powerplug thenpower offthedevice.

7. User Settings

1)CENTER

Text

command

Parameter Sample

CENTER
Add

CENTER,A,num

ber1,number2

number3#

1)CENTER,A,13500135000,1380

0138000,13600136000#

2) CENTER,A,13500135000#

3) CENTER,A,,,13800138000#

CENTER
Del

CENTER,D#

1) CENTER,D,1#

2) CENTER,D,1,2#

2)SERVER

Text
command

Parameter Sample

SERVER
Parameter

SERVER,code,

domain/IP,port#

SERVER,8520,m.gps001.com,8841#

SERVER,8520,121.14.139.39,8080#

Command
Description

This function changes the server settings, you need to
modify the server IP / domain name and port.
Port Range: 10 ~ 65535; wherein Password: 8520;
Domain: either domain name or an IP address.

Command
Feedback

Successful Setting：SET SERVER OK

！

3)APN

Text
command

Parameter Sample

APN APN,SSID[,userna

1：APN,intenet,123,123#

Command
Description

1)Center number can control the oil and power and

resume factory settings

2) Center number can receive the call and text of

vibration alarm and over speeding alarm.

3) three number can be center number

4) add:sample1 add three number at the same

time;sample2 add the first number ;sample3 add the

third number

5) delete :sample1 delete the first center

number;sample 2 delete the first and second number at

the same time;

6)Add new center number by CETNER,A, and delete by

CENTER,D

Command
Feedback

Successful Setting：SET CENTER TEL OK!

Parameter me, password]

2：APN,cmnet#

Command
Description

APN differs according to the local telecom
operators.Users have to comfirm the APN parameter
For example：APN request password，please refer to

Sample1，and Sample2 for no password.

Command
Feedback

Successful Setting：SET APN OK

！

4)LANG

Text
command

Parameter Sample

LANG
Parameter

LANG,1#
LANG,0#

1：CHINESE
0：ENGLISH

Command
Description

When check the location, it will reply the Chinese
location in Chinese language setting; while reply the
URL link when in English language setting.

Command
Feedback

Successful Setting：SET LANG OK！

5)123

Text
command

Parameter Sample

123 123# 123#

POSITION POSITION# POSITION#

Command
Description

Check the current location

Command
Feedback

When check the location, it will reply the Chinese
location in Chinese language setting; while reply the
URL link when in English language setting.

6)WHERE

Text
command

Parameter

Sample

WHERE WHERE#

WHERE#

Command

Check the current longitude and altitude ,time and

Description other information of the device

Command
Feedback

Reply with current longitude and altitude, time,speed
and IMEL.

7)URL

Text
command

Parameter Sample

WHERE URL# URL#

Command
Description

Check the location link of Google map

Command
Feedback

<Datetime:12-07-05 13:21:30>

http://maps.google.com/maps?q=N22.540885,E113.95265

8)TIMER

Text
command

Parameter Sample

TIMEER
Parameter

TIMER,uploading interval# TIMER,30#

Command
Description

Time scope：10~60 seconds

；

10~60,means time interval ； the default value is 10
seconds

！

Command
Feedback

Successful Setting：SET TIMER OK

！

9)VIBRATION

Text
command

Parameter Sample

VIBRATION
Parameter

VIBRATION, alarming
level[,alarming way]#

1)VIBRATION,2,3#

2)VIBRATION,2#

Command
Description

Set vibration alarm Alarm levels is from 0 to 5 ， the
lower level the more sensitive and o is close. Alarming
ways: 1, calling 2, texting, 3 calling and texting.

Default :1.calling ;you don’t have to chose the alarming
way such as sample 2;
Must set the center number and receiving number.

Command
Feedback

Successful reply：SET VIBRATION OK！

10)SPEEDING

Text
command

Parameter Sample

SPEEDING
Parameter

SPEEDING, speed
[alarming way]#

1)SPEEDING,120,3#

2)SPEEDING,120#

Command
Description

The speed scope is form 60-220, if the speed is not in
this scope, the alarm is off. eg：SPEEDING,0#
Alarming ways: 1, calling 2, texting, 3 calling and
texting. Default :1.calling ;you don’t have to chose the
alarming way such as sample 2;

Command
Feedback

Successful Setting：SET SPEEDING OK!

11)PARAM

Text
command

Parameter Sample

PARAM PARAM# PARAM#

Command
Description

The command is to check the settings and the default
parameter.

Command
Feedback

IMEI:351190012535936 device IMEI
APN:cmnet operator GPRS node
IP:www.gps0123.com:8841 sever IP and port
UPLOADING TIME:15S moving uploading interval
LANG:Chinese language(CN/EN)
GMT: time zone (E/W8) time zone(E/W 0~12)

12)STATUS

Text
command

Parameter Sample

STATUS STATUS# STATUS#

Command
Description

The command is designed for checking the device’s
working status.

Command
Feedback

BATTERY:100% -- Battery status (SOC)
GSM Signal: strength --GSM Signal strength
GPS:FIXED --GPS Location condition
GPS Signal: strength --GPS Signal strength
Charging:connect -- power state

voltage :13，4.18 -- power and battery voltage (volts)

13)NUMBER

Text command Text command Text command

NUMBER NUMBER NUMBER

Command Description

Command Description

Command Feedback Command Feedback

14)RESET

Text command Parameter Sample

RESET RESET# RESET#

Command Description

Reset the device

Command Feedback

Successful Setting：RESET OK

！

15)FEE

command Parameter Sample

FEE
Check

FEE,phone
number,contents#

FEE,10010,102# (China Unicom)
FEE,10086,CXYE#(China Mobile)

Command
Descriptio
n

The command is to check the remaining fee of the SIM card

query number: SIM operator’query number

Contents:Contents of the query,Such as mobile CXYE or
101 is the balance inquiry

Command
Feedback

Back to the operator’s reply.

Note:A comma in command must be a comma in English, can't use Chinese

comma, in the middle can also use # to separate, instead of a comma

9. Trouble shooting

9.1 The device is not online or offline on the web platform

9.1.1 First, please check the terminal indicator is nomal or not ,if there’s no

condion for observe,Please use the cell phone to call the terminal SIM card
number, according to the reminding tone to determine the status of the
terminal.

●

If not connected, Indicating that the terminal temporarily can not connect

or the GSM signals cannot reach your location

Terminal area may not becovered by the GSM signal or weak signal in

the basement and other places, please drive to the open sky.

If not connected, suggesting that the Terminal is insufficient Or has been

shut down

If reminding the device SIM card is out of deposit, please make deposit by

the telecom operator.

●

If you can connect to the device when calling,and hear a beep. Du, du.

noise

the SIM card is installed correctly and has deposited and please check
with your operator for GPRS function. You also can check by searching the
internet on your mobile phone. If you can not open website ,the GPRS
function has not open .please contact with the operator to open

● If the terminal is not connected and reminding shutdown

At this moment must recall vehicles to check the working status of the
terminal, the processing steps are as follows:
a) Check whether both lights are flashing or long bright, if not bright, Check
whether the interface between device and car is plugged ok .
b) If the blue GSM LED is not in constant glow, please check the installation
of SIM card.If installed ok ,please change another SIM card to use

9.1.2 Please check the offline area，it’s individual drops or all drops ,in order to judge if
the network problem of operators.

9.2 When GPS signal receiving abnormal, please drive to a open place to
locate.In general locating time need 1 to 2 minutes for the first time,If long
time no locating, please check whether there is a metal barrier surrounding
the installation site of the device affecting the signal.

9.3 When GPS signal receiving abnormal, please check if the SIM card
installed correctly or If the GSM signals cannot reach your location (such as
the basement), please drive to the open sky.

special announcement：

1.If products has technical changes ,we’ve no prior notice.

2.The shape and color, please in kind prevail

3.Warranty card applies to the specified IMEI number in the following table

GPS

locating terminal warranty card

4.Please properly keep this card and receipt in case of after-sales service

5.The following is for the warranty reference

This form is the basic of the warranty certificate information, please fill out the
form carefully

Name Telephone

Address

Type IMEI

Date

Purchase name

Agency address

Agency Phone

1. Hosts are guaranteed for12months, from date of purchase which

products are not being damaged by any man-made factors

2. Listed below are the situation which is not covered under the warranty, users
need to pay maintenance fees

(1) Beyond the warranty period

(2) maintenance and repair by disassembling the machine without

authorization

(3) Soak, damage or burn circuit board

(4) Installation, use, maintenance or improper storage

(5) Housings, lenses or internal damage to the antenna
(6) IMEI number tearing or blurred

(7) Warranty certificate inconsistent with the product model or has been

modified

(8) Damage caused by irresistible force

Maintenance Record

The first time

Maintenance
company

Date

Fault
statement

Maintenance
condition

IMEI serviceman

The second time

Maintenanc
e
company

Date

Fault
statement

Maintenanc
e condition

IMEI

servicema

n

Tenson
[e-mail]