Seeley SIA18 Users Manual

INSTALLATION AND OWNER MANUAL

MaglQtouch WIRELESS Smart Controller

Original English Instructions

TABLE OF CONTENTS

SAFETY

Responsibilities 1
Risk Assessment 1
Warnings 1
FCC Compliance 2

MOUNTING THE MAGIQTOUCH
WIRELESS CONTROLLER

Location 3
Mounting the Controller 4

MOUNTING THE
MAGIQTOUCH WIRELESS
RECEIVER 7

Heater Installation 7
Heater With Zones 8
Cooler Installation 9
Mounting the Receiver 9

COMMISSIONING

Connecting the Receiver 11
Pairing 11

KIT CONTENTS

MagIQtouch Wireless Smart Controller

Item Qty Description

A 1 MaglQtouch Wireless Smart Controller

B 1 MagIQtouch Wireless Receiver

C 4 AA Batteries

D 1 Install & Operation Manual

E 2 Screw PAN PHIL 6AB*1” ZP

F 2 Wall Plug Yellow 5mm

Pairing Additional Controller 13

WIRELESS CONNECTION
MAINTENANCE 15

Wireless RF Signal Range 18

CONTROLLER OR SYSTEM
RESET 19

2X Controllers Connected 20

SUPPORT 23
USER GUIDE 25
GENERAL TIPS 27
REPLACING THE BATTERIES 27
QUICK START 28
SLEEP MODE 29
WIRELESS RANGE 30
ADDITIONAL CONTROLLER 33
TROUBLE SHOOTING 35

Item A

ItemB

Item C Item D

MagIQtouch Controller INSTALLATION MANUAL | i

SAFETY

This document provides technical
guidance on the installation and
operation of the MagIQtouch WI-FI
smart app.

EMPLOYER AND EMPLOYEE
RESPONSIBILITIES

Please read this manual carefully.
Your failure to do so could result in
injury to you or damage to the cooler
and property.

The installation and maintenance
of evaporative coolers at height has
the potential to create Occupational
Health and Safety issues for those
involved. Installers are advised to
ensure they are familiar with Local
Acts, Regulations and Standards,

which may o󰀨er practical guidance

on health and safety issues.
Compliance with these regulations will
require appropriate work practices,

equipment, training and qualications

of workers.

INSTALLER AND MAINTENANCE
CONTRACTORS– RISK
ASSESSMENT

Seeley International provides the
following information as a guide to
contractors and employees to assist
in minimising risk whilst working at
height.

A risk assessment of all hazardous
tasks is required under legislation.
A risk assessment is an essential
element that should be conducted
before the commencement of work,
to identify and eliminate the risk of
falls or to minimise these risks by
implementing control measures. There
is no need for this to be a complicated
process, it just is a matter of looking
at the job to be done and considering

1 |

what action(s) are necessary so the
person doing the job does not injure
themselves.

This should be considered in terms of:

• What are the chances of an
incident happening?

• What could the possible
consequence be?

• What can you do to reduce, or
better still, completely get rid of
the risk?

WARNINGS!

The MagIQtouch Wireless Smart
Controller and Receiver are to be
installed indoors only, installation
shall only be performed by suitably

trained and qualied personnel, in

accordance with local and national
wiring rules.

This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by
a person responsible for their safety.
Children should be supervised to
ensure that they do not play with
the appliance. If any cables are
damaged, they shall be replaced by
the manufacturer or its service agent

or similarly qualied person in order to

avoid a hazard.

Stranded conductors shall not be
consolidated by lead-tin soldering
where they are subject to contact
pressure, i.e. on terminal block.

SAFETY

FCC COMPLIANCE STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

NOTE: This equipment has been
tested and found to comply with the
limits for a Class B digital device,
pursuant to part 15 of the FCC
Rules. These limits are designed
to provide reasonable protection
against harmful interference in
a residential installation. This
equipment generates, uses and
can radiate radio frequency energy
and, if not installed and used in
accordance with the instructions,
may cause harmful interference to
radio communications. However,
there is no guarantee that
interference will not occur in a
particular installation.

MagIQtouch Controller INSTALLATION MANUAL | 2

If this equipment does cause
harmful interference to radio or
television reception, which can
be determined by turning the

equipment o󰀨 and on, the user is

encouraged to try to correct the
interference by one or more of the
following measures:

• Reorient or relocate the
receiving antenna.

• Increase the separation between
the equipment and receiver.

• Connect the equipment into an

outlet on a circuit di󰀨erent from

that to which the receiver is
connected.

• Consult the dealer or an
experienced radio/TV technician
for help.

MOUNTING THE MAGIQTOUCH WIRELESS
SMART CONTROLLER

LOCATION

The MagIQtouch Wireless Smart Controller should be placed approximately

1.5 metres/5’ above the oor, in the most used room of the home.

Placement is critical for correct functioning of the temperature sensing
thermostat inside the Controller.

The following must be taken into consideration:

• Avoid direct sunlight exposure.

• Avoid mounting on external walls.

• Avoid mounting the wall control near heat sources such as stoves and
televisions.

• Do not locate in the direct airow of the duct outlets.

• Do not locate in strong drafts or in dead spots such as cupboards/
drawers.

CAUTION!

Always make sure there are no electrical cables, gas or water pipes, or the
like, behind where you intend to drill.

3 |

MOUNTING THE MAGIQTOUCH WIRELESS
SMART CONTROLLER

MOUNTING THE CONTROLLER

Remove the mounting bracket from the rear of the MagIQtouch Controller.

Step 1

ILL1584-A

Step 2

ILL1585-A

Step 3

MagIQtouch Controller INSTALLATION MANUAL | 4

ILL1586-B

MOUNTING THE MAGIQTOUCH WIRELESS
SMART CONTROLLER

Step 4

Using the bracket as a template, mark the centre points for the screw and
cable access holes.

ILL1587-A

5 |

MOUNTING THE MAGIQTOUCH WIRELESS
SMART CONTROLLER

Step 5

Insert wall plugs into holes. Align and screw the bracket into position using
the supplied screws.

ILL2937-A

ILL2938-A

Alternatively, a standard stud mounting bracket (used for wall plates) can be
used with plasterboard walls.

MagIQtouch Controller INSTALLATION MANUAL | 6

MOUNTING THE MAGIQTOUCH WIRELESS RECEIVER

We recommend installation of the wireless receiver (Antenna) inside the
ceiling space, as far away from heating/cooling appliances and ductwork as
possible and also as close as practical to the area of the building the remote
controller will be used the most. Therefore, we request that the antenna is
always straightened and pointing towards the remote.

IMPORTANT!

The wireless receiver is not designed to be installed outdoors!

Do not wrap any excess wireless receiver cable around the receiver. Do not
extend the receiver cable.

HEATER INSTALLATION

ILL2853-A

7 |

MOUNTING THE MAGIQTOUCH WIRELESS RECEIVER

HEATER WITH ZONES - INSTALLATION

ILL2854-A

MagIQtouch Controller INSTALLATION MANUAL | 8

MOUNTING THE MAGIQTOUCH WIRELESS RECEIVER

COOLER INSTALLATION

ILL2855-A

MOUNTING THE WIRELESS RECEIVER

For most installations, mounting the receiver as shown (Fig 1) will provide
satisfactory performance.

1

A. Metal Roong

B. Wood or Metal Beam
C. Receiver (mount as close as possible to a

metal roof)

9 |

2

Using the communication cable
supplied, connect it to the RJ
socket as shown

ILL670-E

ILL665-D