Seeley SIA06, ELITE Owners Manual

REMOTE CONTROL

®

owner’s manual

AUTO COOL

FAN

SPEED

PM

ECONOMY

BATTERY LOW

Hello and congratulations on
purchasing a Breezair Ducted
Cooler for your home.

Breezair coolers have been
designed to provide quiet,
reliable and cool comfort.

At Seeley International we
manufacture Breezair
evaporative coolers from the
highest quality materials, and
we have designed the product
to provide many years of
economical, trouble free
cooling.

Please take a few moments to
read these operating
instructions, so that the most
can be gained from this
investment.

Breezair coolers are fitted
with either a Wall Mounted
Thermostat Control or a
Remote Thermostat Control.
Please refer to the relevant
section in this manual for
instructions on how to operate
either system. Also, please be
aware of the components and
features that are fitted to your
particular cooler.

®

®

®

®

EFFECTIVE COOLING

To provide efficient cooling or
ventilation the building must
have sufficient exhaust
openings to the outside of the
building. To assist air flow, open
windows and doors that are
farthest from the outlet vent in
each room. In these rooms,
provide an exhaust opening
about 2 times the vent size of
the room.

Where the design of the
building prevents adequate
exhaust, consideration should
be given to the provision of
mechanical extractions, such
as an exhaust fan.

Important Note!

In areas where temperatures
can cause water supply pipes
to freeze, a drain down facility
should be provided during the
installation.
This drain down facility must be
activated prior to freezing
conditions, to avoid possible
damage to the cooler
components.

page

introduction

Keep these instructions in a
safe place for future reference.

®

2

range

REMOTE CONTROL

thermostat

AUTO COOL

FAN

SPEED

Remote Thermostat Control

(remote control)

PM

ECONOMY

ILL239-D

ILL1140-A

Wall Mounted Thermostat Control

(wall control)

3

®

Remote Thermostat Control..............5

Wall Mounted Thermostat Control...11

page

contents

Bleed Funnel & Drain Valve............15

Power Outages...............................15

Seasonal Maintenance...................16

Troubleshooting..............................18

Service & Warranty.........................20

®

4

SETTING THE CLOCK

Set the clock on the remote
control before proceeding with
any other programming.

The clock can only be set with
the remote control switched
OFF. Hold the button
down for over 2 seconds, until
the hour flashes.

The clock can
be set to either 12 or 24 hours
(see page 10). If the clock is set
to 12 hours make sure that the
AM/PM displayed on the screen
is correct. AM/PM will change
with adjustment of the hour.

PM

thermostat control

and use the settings from when
the cooler was last used. Once
the remote control is on, you
can choose between MANUAL,
AUTO and AUTO TIMER
modes by pressing the

button.

MANUAL MODE

With the remote control ON,
press the button until
MANUAL is shown in the top
left corner of the display.

MANUAL

FAN

SPEED

COOL

ILL1108-A

Use the and buttons
to change the hour. To change
minutes, press the button
again. Change the minutes
using the and
buttons.

remote

To lock in the time setting, and
enter the OFF state, press the

button. The display will

stop flashing.

TURNING THE
COOLER

The remote control is switched
on and off using the
button. The memory will store

5

ON

ILL1104-A

®

The button is used to
select VENT (where fresh air is
being delivered without being
cooled) or COOL.

MANUAL VENT

FAN

SPEED

ILL1109-A

Once either COOL or VENT
has been selected, the remote
control will maintain a constant
fan speed. This is indicated by
the bar graph in the centre of
the display.

To or the fan

decrease increase

speed required, press either the

or buttons.

AUTO MODE

The remote control contains a
thermostat. In AUTO mode the
cooler is controlled
automatically, based on your
pre- comfort level. The

selected

cooler will adjust the fan speed,
switch between COOL and
VENT and turn itself off.
However, the sequence and
regularity at which these
settings change will differ with
each operation of the cooler.

As the remote control senses
room conditions, the

control settings will be
influenced by

heat from direct
sunlight or electrical appliances.
Likewise placing the remote
control in cupboards or drawers
or under cooling vents will affect
the cooler’s operation.

To set the AUTO mode press
the button until AUTO is
displayed.

AUTO

FAN

SPEED

comfort

PM

indicating a level between 1
and 10. WARMER or COOLER
will be displayed on the screen
as settings are changed.

AUTO TIMER MODE

AUTO TIMER mode can be
selected by using the
button. Once the AUTO TIMER
mode is selected the cooler will
only operate during the
programmed time period.

Programming the timer must be
performed before AUTO TIMER
can be activated. This can be
done while in any mode, even
when it is OFF. There are 7
steps involved in setting the
AUTO TIMER.

NOTE: After pressing the
button the display will revert
back to the previous setting if
no buttons are pressed within 4
seconds.

To program the timer use the
following sequence:

(1) Setting the ON time hour

thermostat control

remote

ILL1105-A

Ten levels of comfort are
available with the remote
control. While in AUTO mode
pressing the and
buttons will adjust the level of
required comfort. The display

will show your selection by

®

Begin by pressing the
button. The hour displayed will
start flashing and the word ON
will appear on the screen. Then
use the and buttons
to change the hour value.

AUTO

TIMER

ON

ILL1112-A

6

(2) Setting the ON time minutes

(5) Setting the comfort level

Press the button. The
minutes displayed will start
flashing and the word ON will
appear on the screen. Then use
the and buttons to
change the minute setting.

AUTO

TIMER

ON

ILL1113-A

(3) Setting the OFF time hour

Press the button. The
hour displayed will start flashing

thermostat control

and OFF will be displayed. Then
use the and buttons
to change the hour.

AUTO

TIMER

OFF

ILL1114-A

(4) Setting the OFF time minutes

remote

Press the button. The
minutes displayed will start
flashing and the word OFF will
appear. Then use the and

buttons to change the

minute setting.

AUTO

TIMER

OFF

ILL1115-A

®

7

Press the button and the
comfort level number (1 to 10)
displayed will start flashing.
Then use the and
buttons to change this setting.

AUTO

TIMER

ILL1116-A

(6) Setting ECONOMY

To select economy press the

button so that it is displayed

on the screen.

(7) Activating AUTO TIMER

Now that you have
programmed the settings for
AUTO TIMER they will be
stored in the remote control’s
memory until you change them.
Press the button until
AUTO TIMER is displayed on
the screen. Your cooler will now
only operate during the
programmed time period.

NOTE: To change any AUTO
TIMER settings when the
remote control is switched off,
the button needs to be
pressed and released within 1
second. To change settings
when the remote control is
turned on press the
button until the desired number
is flashing.