Page 1
ITEM NO.: T-4096XXB AND T-4096XXT OR T-3896XXT
(PACKED IN SEPARATE BOX)
REVISED MAY 08, 2019
Printed in Vietnam
Description
Item No.
: MILANO TABLE BASE
: T-4096XXB AND T-4096XXT OR T-3896XXT
(PACKED IN SEPARATE BOX)
ASSEMBLY INSTRUCTIONS
T-4096XXB AND T-4096XXT
T-4096XXB AND T-3896XXT
- 1 -
Page 2
ITEM NO.: T-4096XXB AND T-4096XXT OR T-3896XXT
(PACKED IN SEPARATE BOX)
REVISED MAY 08, 2019
Printed in Vietnam
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
- Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
- Remove all wrapping material, including staples & packing straps before you start to
assemble.
- DO NOT tighten all screws and bolts until completely assembled.
- Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish
of your table. Protect the surface of the table with cloth if you are using any product with
rubber feet or base.
- 2 -
Page 3
ITEM NO.: T-4096XXB AND T-4096XXT OR T-3896XXT
(PACKED IN SEPARATE BOX)
REVISED MAY 08, 2019
Printed in Vietnam
NO
Description
Qty
Sketch
A
Top
1
NO
Description
Qty
Sketch
A
Top
1
PART LIST T-4096XXT
PART LIST T-3896XXT
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
- 3 -
Page 4
ITEM NO.: T-4096XXB AND T-4096XXT OR T-3896XXT
(PACKED IN SEPARATE BOX)
REVISED MAY 08, 2019
Printed in Vietnam
PART LIST T-4096XXB
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
B
Long leg
2
C
Short leg
2
D
Pedestal
column
2
E
Crossbar
1
HARDWARE LIST
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Hexagon Nut
(M8 x 13mm)
12
2
Flat Washer
(2 x 8.5 x 19mm)
12
3
Lock Washer
(8.5 x 11mm)
12
4
Wrench
(M13mm)
1
5
Wood Screw
(M4 x 30mm)
4
6
Bolt
(M8 x 70mm)
2
7
Allen key
(M4 x 30mm x 110mm)
1
8
U-washer
(M8)
2
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NOTE: HARDWARE IS PACKED IN CARTON T-4096XXB.
- 4 -
Page 5
ITEM NO.: T-4096XXB AND T-4096XXT OR T-3896XXT
(PACKED IN SEPARATE BOX)
REVISED MAY 08, 2019
Printed in Vietnam
STEP 1
STEP 2
A
Attach crossbar (E) to pedestal columns (D) with bolts (6) and u-washers (8) as shown below. Tighten
with Allen key (7).
Insert short legs (C) into long legs (B) and attach with screws (5) as shown below. Tighten with a
screwdriver.
Attach legs (B) to pedestal columns (D) with nuts (1), and washers (2) and (3) as shown below. Tighten
with the wrench (4).
Use Allen key (7) to loosen bolts and washers and take out the mounting plates underneath the table
top as shown below.
- 5 -
Page 6
ITEM NO.: T-4096XXB AND T-4096XXT OR T-3896XXT
(PACKED IN SEPARATE BOX)
REVISED MAY 08, 2019
Printed in Vietnam
STEP 3
STEP 4
A
Attach mounting plates on top of the pedestals (D) with nuts (1), and washers (2) and (3) as shown
below. Tighten with the wrench (4).
Carefully place the base on the bottom side of the top (A).
Attach mounting plates to top (A) with bolts and washers (from step 2) as shown below. Tighten with
Allen key (7).
- 6 -
Page 7
ITEM NO.: T-4096XXB AND T-4096XXT OR T-3896XXT
(PACKED IN SEPARATE BOX)
REVISED MAY 08, 2019
Printed in Vietnam
STEP 5
Unlock the table top from both sides underneath the top as shown below. Pull the two parts of the
table top apart.
- 7 -
Page 8
ITEM NO.: T-4096XXB AND T-4096XXT OR T-3896XXT
(PACKED IN SEPARATE BOX)
REVISED MAY 08, 2019
Printed in Vietnam
STEP 6
Place the leaves in the center of the open table top, as shown below.
Note: The metal swivel bar bracket is very flexible and a slight twist of one half of the leaf can get the
leaf into alignment. With one of these tops opened and in the topside up position and can be
attached to the base to accomplish this too.
Have the top fully extended first, pull the leaf operation out, and with one leaf end down and other in
the upward position, grasp the sides of the leaf w/ two hands and twist slightly (the metal bracket is
flexible) so to shift the alignment of the leaf and then lower it into place being careful not to let the
metal pins hit the edges of top or the leaf apron end, but repeat if necessary so to get the pins to align.
We use the flexible metal bar for this purpose, as a hardened metal would snap during transport or
damage the under structure.
1 LEAF 2 LEAVES
- 8 -
Page 9
ITEM NO.: T-4096XXB AND T-4096XXT OR T-3896XXT
(PACKED IN SEPARATE BOX)
REVISED MAY 08, 2019
Printed in Vietnam
STEP 7
Push the table top closed. Lock the mechanism underneath two sides of the table top as shown below.
1 LEAF 2 LEAVES
- 9 -
Loading...