Security Tronix ST-WD600PTZMINI Installation Manual

v2.2 7/28/11

1

INSTALLATION MANUAL

ST-WD600PTZMINI

Vandalproof Intelligent Dome PTZ

Color Camera

v2.2 7/28/11

2

PACKAGE CONTENTS

This package contains:

One ST-WD600PTZMINI vandalproof intelligent dome color camera
One installation manual

Note: The ST-WD600PTZMINI requires a minimum 12VDC 500mA power supply such as the
ST-PS12VDC1A or ST-PS12VDC2A.

PRODUCT DESCRIPTION

The ST-WD600PTZMINI is a professional grade IP66-rated outdoor dome color camera with pan,
tilt and zoom (PTZ) capability of 600TVL of resolution. The camera’s full digital design allows the
saving of all settings in non-volatile memory. The camera features include a 5mm – 15mm
varifocal lens.

SPECIFICATIONS

ST-WD600PTZMINI

Specifications (Typical)

1. Image Sensor

1/3” SONY Super HAD CCD II

2. Resolution

600TVL

3. Lens

5mm – 15mm auto focus lens

4. Effective Picture Elements

811x508

5. Minimum Illumination

0.001 Lux

6. Scanning System

2:1 interface

7. Video Output

1.0VP-P, 75Ω

8. Signal to Noise Ratio

>48dB

9. Synchronous System

Internal, Negative synch

10. Auto Electronic Shutter

1/60s ~ 1/100,000s

11. Gama Correction

0.45

12. Auto Gain Control

Auto

13. Power

DC12V 500mA

14. Operating Relative Humidity

95% maximum

15. Operating Temperature

14°F – 113°F

16. Dimensions

4.8”x7”

17. Weight

3.3 lbs

v2.2 7/28/11

3

INSTALLATION AND OPERATION

CAUTION: To reduce the risk of electrical shock do not remove the cover or back of this

unit. No user serviceable parts are inside.

CAUTION: To prevent electric shocks and risk of fire hazards, do not use other than

specified power source.

1. UNPACKING and HANDLING

Each unit is shipped assembled and factory tested.

Ensure that all accessories are removed from the container before discarding packing material

2. MECHANICAL INSPECTION

Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is
clean, and no connectors are broken, damaged, or loose. If equipment appears to be
damaged or defective please contact your distributor or Securitytronix at 1-610-429-1511 for
assistance.

3. SPECIAL ATTENTION

a. The installer must comply with electrical safety standards. There must be sufficient

space between the camera’s power supply and video line and any high voltage
equipment and/or cables.

b. To help ensure the camera’s life and proper operation do not point the camera

towards the sun or strong light.

c. Do not install the camera in an environment where the temperature is above 113° F.

d. Do not install the camera near a magnetic field or a high-power motor.

e. Do not mount the camera near a radiator or heater.

f. Only use a dry cloth to clean the camera. If there is dirt that is difficult to remove wipe

gently with a mild detergent. Never use strong or abrasive detergents.

g. A minimum 12VDC 500mA power supply must be used. AC power cannot be applied.

Using an AC or other incorrect power supply will damage the camera.

h. Only qualified installers are allowed to install, test and disassemble the camera.

i. The camera is a low voltage product. If installed outdoors proper safety and lightening

grounding are required.

This symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions.

This symbol is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electrical shock.