Page 1
ST-IP2VFD QUICK
START GUIDE
www.securitytronix.comwww.nacebrands.com
Page 2
ST-IP2VFD QUICK START GUIDE
1
1
Thank you for purchasing our product. If there are any questions, or
requests, please do not hesitate to contact the dealer.
About This Document
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We will
readily improve or update the products or procedures described in
the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of this
product. UL has only tested for fire, shock or casualty hazards as
outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification
does not cover the performance or reliability of the security or
signaling aspects of this product. UL MAKES NO REPRESENTATIONS,
WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING
RELATED FUNCTIONS OF THIS PRODUCT.
Page 3
ST-IP2VFD QUICK START GUIDE
2
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at their
own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the
EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
Page 4
ST-IP2VFD QUICK START GUIDE
3
3
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more information
see: www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information
see: www.recyclethis.info
Page 5
ST-IP2VFD QUICK START GUIDE
4
4
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings
are neglected.
Cautions: Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings
● While using this product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.
● Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 24 VAC or 12 VDC
according to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.
Page 6
ST-IP2VFD QUICK START GUIDE
5
5
● Do not connect several devices to one power adapter as adapter
overload may cause over-heating or a fire hazard.
● Please make sure that the plug is firmly connected to the power
socket. When the product is mounted on wall or ceiling, the
device shall be firmly fixed.
● If smoke, odor or noise rise from the device, turn off the power
at once and unplug the power cable, and then please contact
the technical support.
Cautions
● Make sure the power supply voltage is correct before using the
camera.
● Do not drop the camera or subject it to physical shock.
● Do not touch sensor modules with fingers. If cleaning is
necessary, use a clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period,
please replace the lens cap to protect the sensor from dirt.
● Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur otherwise (which is not a
malfunction), and affect the endurance of sensor at the same
time.
● The sensor may be burned out by a laser beam, so when any
laser equipment is in use, make sure that the surface of sensor
will not be exposed to the laser beam.
Page 7
ST-IP2VFD QUICK START GUIDE
6
6
● Do not place the camera in extremely hot, cold (the operating
temperature shall be-22F~+140F,or -40°F ~ 140°
F if the camera
model has an “H” in its suffix), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
● To avoid heat accumulation, good ventilation is required for
optimal operation.
● Keep the camera away from liquid while in use.
● While in delivery, the camera shall be packed in its original
packing, or packing of the same texture.
● Regular part replacement: a few parts (e.g. electrolytic
capacitor) of the equipment shall be replaced regularly
according to their average life span. The average time varies
because of differences between operating environment and
usage.
● Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.
●
If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (Securitytronix shall not
assume any responsibility for problems caused by unauthorized
repair or maintenance.)
Page 8
ST-IP2VFD QUICK START GUIDE
7
7
Table of Contents
1 Appearance Description ................................................................. 8
2 Installation .................................................................................... 11
2.1 Disassembling ............................................................... 12
2.2 Mounting ...................................................................... 13
2.2.1 Ceiling Mounting ................................................ 13
2.2.2 Ceiling Mounting with Gang Box ........................ 17
2.2.3 Wall Mounting .................................................... 20
2.3 Image and Focus Adjusting ............................................ 23
3 Setting the Network Camera over the LAN .................................. 26
4 Accessing via Web Browser .......................................................... 31
Page 9
ST-IP2VFD QUICK START GUIDE
8
8
1 Appearance Description
The overview of the network dome camera is shown below.
Figure 1-1 Overview
4
2
3
1
9
10
5
6
7
11
8
Page 10
ST-IP2VFD QUICK START GUIDE
9
9
Table 1-1 Description
No.
Description
1
Bubble
2
Black Liner
3
Lens
4
Mounting Base
5
Reset
6
Auxiliary Video Output
7
Serial Port
8
Micro SD Card Slot
9
Network Cable
10
Power Cable
11
Audio/Alarm Interface
Press RESET about 10s when the camera is powering on or
rebooting to restore the default settings, including the user name,
password, IP address, and port No., etc.
Some of the models support audio and alarm functions. The
interfaces are shown as follows.
Page 11
ST-IP2VFD QUICK START GUIDE
10
10
Figure 1-2 Audio and Alarm Interfaces
Alarm/Audio Cable Interface
Page 12
ST-IP2VFD QUICK START GUIDE
11
11
2 Installation
Before you start:
Make sure the device in the package is in good condition and all
the assembly parts are included.
Make sure all the related equipment is powered off during the
installation.
Check the specification of the products for the installation
environment.
Make sure the power supply is matched with your required
voltage to avoid damage.
If the product does not function properly, please contact your
dealer or technical support. Do not disassemble the camera for
repair or maintenance by yourself.
Make sure that the wall is strong enough to withstand three
times the weight of the camera.
For the cameras that supports IR, you are required to pay attention
to the following precautions to prevent IR reflection:
● Dust or grease on the dome cover will cause IR reflection.
Please do not remove the dome cover film until the installation
is completed. If there is dust or grease on the dome cover,
clean the dome cover with clean soft cloth and isopropyl
alcohol.
Page 13
ST-IP2VFD QUICK START GUIDE
12
12
● Make sure that there is no reflective surface too close to the
camera lens. The IR light from the camera may reflect back into
the lens causing poor image quality.
● The foam ring around the lens must be seated flush against the
inner surface of the bubble to isolate the lens from the IR LEDS.
Fasten the dome cover to camera body so that the foam ring
and the dome cover are attached seamlessly.
2.1 Disassembling
Steps:
1. Loosen the three screws on the edge of the bubble with the screw
driver.
2. Open the bubble and remove the inner black liner as shown in
Figure 2-1.
Figure 2-1 Remove the Bubble and Black Liner
Black Liner
Bubble
Screw Hole
Page 14
ST-IP2VFD QUICK START GUIDE
13
13
2.2 Mounting
Ceiling Mounting
Steps:
1. Disassemble the camera. Refer to the section 2.1.
2. Attach the drill template (supplied) to the place where you want
to fix the camera.
3. According to the drill template as shown in Figure 2-2, drill three
screw holes in the ceiling.
Figure 2-2 The Drill Template
4. If you want to route the cables inside the ceiling, drill a cable hole
in the ceiling according to the drill template. Skip this step if you
Cable Outlet
Screw Hole
Drilling Template for Outdoor
Day/Night Vandal-proof Dome Camera
Side Cable Outlet
Page 15
ST-IP2VFD QUICK START GUIDE
14
14
want to route the cables on the surface of the ceiling. Refer to
Conduit Installation on the Side for side cable routing.
5. Attach the camera to the ceiling by aligning the holes of the back
box with the holes on the ceiling.
6. Secure the camera with the supplied screws as shown in Figure
2-3.
Figure 2-3 Secure the Camera
7. Route the cables through the cable hole.
8. Connect the video output connector to the monitor. Connect the
power connector to the power supply.
9. Adjust the image and focus. Please refer to the section 2.3 for
more detailed information.
10. Install the inner black liner back to the camera.
11. Install the bubble back to the camera and secure it with screws
as shown in Figure 2-4.
Screw
Back Box
Page 16
ST-IP2VFD QUICK START GUIDE
15
15
Figure 2-4 Secure Black Liner and Bubble
Conduit Installation on the Side
If you want to route the cables from side of the camera, you need to
follow the steps below to install a conduit for cable routing.
Steps:
1. Rotate the water-proof plug counterclockwise to remove it from
the camera.
Page 17
ST-IP2VFD QUICK START GUIDE
16
16
Figure 2-5 Remove the water-proof plug
2. Route the power cable and network cable through the side outlet
to the conduit.
3. Align and rotate clockwise the conduit to the side outlet tightly.
Figure 2-6 Install the Conduit to the Camera
Water-proof Plug
Side Cable Outlet
Conduit
Page 18
ST-IP2VFD QUICK START GUIDE
17
17
For wall mounting, position the side outlet directly downward for
water-proof.
Figure 2-7 Side Outlet Direction
2.2.2 Ceiling Mounting with Gang Box
Steps:
1. Disassemble the camera. Refer to the section 2.1.
2. Install the gang box in the ceiling.
3. Attach the mounting base to the gang box with two screws.
Downward
Page 19
ST-IP2VFD QUICK START GUIDE
18
18
Figure 2-8 In-ceiling Mount
4. Route the cables through the hole in the center of the mounting
base.
5. Align the camera with the mounting base.
6. Tighten the screws to secure the camera with the mounting base.
7. Connect the video output connector to the monitor. Connect the
power connector to the power supply.
8. Adjust the image and focus. Please refer to the section 2.3 for
more detailed information.
Mounting Base
Page 20
ST-IP2VFD QUICK START GUIDE
19
19
Figure 2-9 Secure Camera
9. Install the inner black liner back to the camera.
10. Align the bubble with the camera.
11. Tighten the screws to secure the bubble with the camera as
shown in Figure 2-10.
Ceiling
Page 21
ST-IP2VFD QUICK START GUIDE
20
20
Figure 2-10 Secure the Bubble
2.2.3 Wall Mounting
For wall mounting, you have to purchase a wall mount separately.
Steps:
1. Disassemble the camera. Refer to the section 2.1.
2. Install the wall mount and mounting adapter as shown in Figure
2-11.
3. Align the screw holes of the mounting base with the
corresponding screw holes of the mounting adapter.
4. Secure the mounting base to the mounting adapter with four
screws.
Page 22
ST-IP2VFD QUICK START GUIDE
21
21
Figure 2-11 Install the Mounting Base
5. Route the cables through the hole in the center of the wall mount.
6. Align the camera with the mounting base.
7. Tighten the set screws to secure the camera with the mounting
base.
8. Connect the video output connector to the monitor. Connect the
power connector to the power supply.
9. Adjust the image and focus. Please refer to the section 2.3 for
more detailed information.
Mounting Adapter
Mounting Base
Page 23
ST-IP2VFD QUICK START GUIDE
22
22
Figure 2-12 Secure Camera
10. Install the inner black liner back to the camera.
11. Align the bubble with the camera.
12. Tighten the screws to secure the bubble with the camera.
Page 24
ST-IP2VFD QUICK START GUIDE
23
23
Figure 2-13 Secure Black Liner and Bubble
2.3 Image and Focus Adjusting
Steps:
1. 3-axis adjustment.
1). View the camera image using a test monitor.
2). Rotate the panning table to adjust the panning position of the
camera.
3). Rotate the tilting axis to adjust the tilting position of the
camera.
4). Rotate the lens assembly to adjust the azimuth angle of the
image.
Page 25
ST-IP2VFD QUICK START GUIDE
24
24
Figure 2-14 3-axis Adjustment
2. Zoom and focus adjustment.
1). View the camera image using a test monitor.
2). Loosen the zoom lever and move the lever between T (Tele)
and W (Wide) to obtain the appropriate view angle.
3). Tighten the zoom lever.
4). Loosen the focus lever and move the lever between F (Far) and
N (Near) to obtain the optimum focus.
5). Tighten the focus lever.
Rotation
Panning
Tilting
Page 26
ST-IP2VFD QUICK START GUIDE
25
25
Figure 2-15 Lens Adjustment
Zoom/Focus
Lever
Menu Button
Page 27
ST-IP2VFD QUICK START GUIDE
26
26
3 Setting the Network Camera over the
LAN
Purpose:
To view and configure the camera via LAN (Local Area Network),
you need to connect the network camera in the same subnet as
your PC. Then, install the SADP or client software to search and
change the IP of network camera.
The following figure shows the cable connection of network
camera to PC:
Figure 3-1 Wiring over LAN
Set the IP address of the camera for accessing via LAN.
Steps:
1. To get the IP address, you can choose either of the following
methods:
Use SADP, a software tool which can automatically detect
network cameras in the LAN and list the device information like
IP address, subnet mask, port number, device serial number,
device version, etc., shown in 0.
Page 28
ST-IP2VFD QUICK START GUIDE
27
27
Use client software to list the online devices. Please refer to the
user manual of client software for detailed information.
2. Change the IP address and subnet mask to the same subnet of
your PC.
Refer to the following introductions to set IP address with SADP
software:
Search active devices online
Search online devices automatically:
After launching the SADP software, it automatically searches
the online devices every 15 seconds from the subnet where
your computer is located. It displays the total number and
information of the searched devices in the Online Devices
interface. Device information including the device type, IP
address, port number, gateway, etc. will be displayed.
Page 29
ST-IP2VFD QUICK START GUIDE
28
28
Figure 3-2 Search Online Devices
Device can be searched and displayed in the list 15 seconds
after it goes online; it will be removed from the list 45
seconds after it goes offline.
Search online devices manually:
You can also click to refresh the online device
list manually. The newly searched devices will be added to
the list.
Page 30
ST-IP2VFD QUICK START GUIDE
29
29
You can click or on each column heading to order
the information; you can click to show the device table
and hide the network parameter panel on the right side, or
click to show the network parameter panel.
Modify device information
Steps:
1). Select the device to be modified in the device list as shown
in Figure 3-3. The network parameters of the device will be
displayed in the Modify Network Parameters panel on the
right side as shown in Figure 3-4.
Edit the modifiable network parameters, e.g. IP address and
port number.
Enter the password of the admin account of the device in the
Password field and click Save to save the changes.
Figure 3-3 Select a Device
Page 31
ST-IP2VFD QUICK START GUIDE
30
30
Figure 3-4 Modify Network Parameters
3. Enter the IP address of the network camera in the address field of
the web browser to view the live video.
The default IP address is “192.0.0.64”. The default user name is
“admin”, and password is “12345”.
For accessing the network camera from different subnets, please
set the gateway for the network camera after you log in.
Page 32
ST-IP2VFD QUICK START GUIDE
31
31
4 Accessing via Web Browser
System Requirement:
Operating System: Microsoft Windows XP SP1 and above version /
Vista / Win7 / Server 2003 / Server 2008 32bits
CPU: Intel Pentium IV 3.0 GHz or higher
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 6.0 and above version, Apple Safari
5.02 and above version, Mozilla Firefox 3.5 and above version and
Google Chrome8 and above version
Steps:
1. Open the web browser.
2. In the browser address bar, input the IP address of the network
camera, e.g., 192.0.0.64 and press the Enter key to enter the
login interface.
3. Input the user name and password.
4. Click Login.
Page 33
ST-IP2VFD QUICK START GUIDE
32
32
Figure 4-1 Login Interface
5. Install the plug-in before viewing the live video and managing
the camera. Please follow the installation prompts to install the
plug-in.
You may have to close the web browser to finish the installation of
the plug-in.
Page 34
ST-IP2VFD QUICK START GUIDE
33
33
Figure 4-2 Download Plug-in
Figure 4-3 Install Plug-in(1)
Page 35
ST-IP2VFD QUICK START GUIDE
34
34
Figure 4-4 Install Plug-in(2)
6. Reopen the web browser after the installation of the plug-in and
repeat the steps 2-4 to login.
For detailed instructions of further configuration, please refer to the
user manual of network camera.
If there are any questions, or requests, please contact our
support department at 1-800-688-9282.
Page 36
0
SECURITYTRONIX 2-Year Limited Fixed Camera Warranty
Securitytronix. (the "Company") warrants to the Original Purchaser that the Fixed Camera is free from
defects in workmanship or material under normal use. This warranty starts on the date of shipment
of the hardware to the Original Purchaser.
During the warranty period, the Company agrees to repair or replace, at its sole option, without
charge to Original Purchaser, any defective component in the Fixed Camera. To obtain service, the
Original Purchaser must return the Fixed Camera to the Company properly packaged for shipping. All
defective products must be returned to the Company within thirty (30) days of failure. Products must
be returned with a description of the failure and Return Merchandise Authorization (RMA) number
supplied by the Company. To receive a RMA number and a return shipping address on where to
deliver the hardware, call 610-429-1821. The shipping, and insurance charges incurred in shipping to
the Company will be paid by Original Purchaser, and all risk for the hardware shall remain with the
Original Purchaser until such time as Company takes receipt of the hardware. Upon receipt, the
Company will promptly repair or replace the defective unit, and then return said unit to Original
Purchaser, shipping prepaid. The Company may use reconditioned or like-new parts or units, at its
sole option, when repairing any hardware. Repaired products shall carry the same amount of
outstanding warranty as from original purchase. Any claim under the warranty must include dated
proof of purchase or invoice. In any event, the Company's liability for defective hardware is limited to
repairing or replacing the hardware.
This warranty is contingent upon proper use of the hardware by Original Purchaser and does not
cover: if damage is due to Acts of God (including fire, flood, earthquake, storm, hurricane or other
natural disaster), accident, unusual physical, electrical, or electromechanical stress, modifications,
neglect; misuse, operation with media not approved by the Company, tampering with or altering of
the hardware, war, invasion, act of foreign enemies, hostilities (regardless of whether war is
declared), civil war, rebellion, revolution, insurrection, military or usurped power or confiscation,
terrorist activities, nationalization, government sanction, blockage, embargo, labor dispute, strike,
lockout or interruption or failure of electricity, air conditioning, or humidity control, internet,
network, or telephone service
The warranties given herein, together with any implied warranties covering the hardware, including
any warranties of merchantability or fitness for a particular purpose, are limited in duration to two
years from the date of shipment to the Original Purchaser. Jurisdictions vary with regard to the
enforceability of warranty limitations, and you should check the laws of your local jurisdiction to find
out whether the above limitation applies to you.
The Company shall not be liable to your for loss of data, loss of profits, lost savings, special,
incidental, consequential, indirect, or other similar damages arising from breach of warranty, breach
of contract, negligence, or other legal action even if the Company or its agent has been advised of the
possibility of such damages, or for any claim brought against your by another party. Jurisdictions vary
with regard to the enforceability of provisions excluding or limiting liability for incidental or
consequential damages. You should check the laws of your local jurisdiction to find out whether the
above exclusion applies to you.
This warranty allocates risks of product failure between Original Purchaser and the Company. The
Company's hardware pricing reflects this allocation of risk and the limitations of liability contained in
this warranty. The warranty set forth above is in lieu of all other express warranties, whether oral or
written. The agents, employees, distributors, and dealers of the Company are not authorized to make
modification to this warranty, or additional warranties binding on the Company. Accordingly,
additional statements such as dealer advertising or presentations, whether oral or written, do not
constitute warranties by the Company and should not be relied upon.
This warranty gives you specific legal rights. You may also have other rights which vary from one
jurisdiction to another.
Loading...