Security Tronix ST-HDC2FB, ST-HDC2FB-2.8 Quick Start Manual

User Manual

This manual includes instructions for using and
managing the product. Pictures, charts, images and all
other information hereinafter are for description and
explanation purposes only. The information contained
in the manual is subject to change, without notice.
Please find the latest version on the company
website. Please use this user manual under the
guidance of professionals.

WARNING: THIS PRODUCT CAN EXPOSE YOU
TO POLYBROMINATED BIPHENYLS, WHICH IS
KNOWN TO THE STATE OF CALIFORNIA TO
CAUSE CANCER AND BIRTH DEFECTS OR
OTHER REPRODUCTIVE HARM. FOR MORE
INFORMATION GO TO
WWW.PROP65WARNINGA.CA.GOV

Legal Disclaimer

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE
CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION
BEFORE USING THIS PRODUCT IN ORDER TO ENSURE
THAT YOUR USE CONFORMS TO THE APPLICABLE
LAWS. OUR COMPANY SHALL NOT BE LIABLE IN THE
EVENT THAT THIS PRODUCT IS USED FOR
ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS
MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.

ST-HDC2FB

ST-HDC2FB-2.8

QUICK START GUIDE

www.securitytronix.comwww.nacebrands.com

Regulatory Information

FCC Information

Please take attention that changes or modification not
expressly approved by the party responsible for

compliance could void the user’s authority to operate

the equipment.
FCC compliance: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,
including interference that may cause undesired
operation.

EU Conformity Statement

This product and - if applicable - the
supplied accessories too are marked with
"CE" and comply therefore with the

applicable harmonized European
standards listed under the Low Voltage Directive
2014/35/EU, the EMC Directive 2014/30/EU.

2012/19/EU (WEEE directive): Products

marked with this symbol cannot be

disposed of as unsorted municipal waste in

the European Union. For proper recycling,

return this product to your local supplier

upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a

battery that cannot be disposed of as

unsorted municipal waste in the European

Union. See the product documentation for

specific battery information. The battery is

marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery
to your supplier or to a designated collection point. For
more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.

Safety Instruction

These instructions are intended to ensure that user can
use the product correctly to avoid danger or property
loss.

The precaution measure is divided into “Warnings” and
“Cautions”.

Warnings: Serious injury or death may occur if any of
the warnings are neglected.
Cautions: Injury or equipment damage may occur if any
of the cautions are neglected.

Warnings

 When using this product, you must be in strict

compliance with the electrical safety regulations of
the nation and region. Please refer to technical
specifications for detailed information.

 Input voltage should meet both the SELV (Safety

Extra Low Voltage) and the Limited Power Source
with 12 VDC according to the IEC60950-1 standard.
Please refer to technical specifications for detailed
information.

 Do not connect several devices to one power adapter

as adapter overload may cause over-heating or a fire
hazard.

 Please make sure that the plug is firmly connected to

the power socket. When the product is mounted on
wall or ceiling, the device should be firmly fixed.

 If smoke, odor or noise rise from the device, turn off

the power at once and unplug the power cable, and
then please contact the service center.

Cautions

 Make sure the power supply voltage is correct

before using the camera.

 Do not drop the camera or subject it to physical

shock.

 Do not touch sensor modules with fingers. If

cleaning is necessary, use a clean cloth with a bit of
ethanol and wipe it gently. If the camera will not be
used for an extended period, please cap the lens to
protect the sensor from dirt.

 Do not aim the camera at the sun or extra bright

places. Blooming or smearing may occur otherwise
(which is not a malfunction), and affect the
endurance of the sensor at the same time.

 The sensor may be damaged by a laser beam, so

when any laser equipment is in use, make sure that
the surface of the sensor will not be exposed to the
laser beam.

Warnings Follow
these safeguards to
prevent serious injury
or death.

Cautions Follow these
precautions to prevent
potential injury or
material damage.

 Do not place the camera in extremely hot, cold (the

operating temperature should be -22°F to +140°C),
dusty or damp locations, and do not expose it to
high electromagnetic radiation.

 To avoid heat accumulation, good ventilation is

required in the operating environment.

 Keep the camera away from liquid while in use.
 During transport, the camera should be packed in its

original packing, or packing of the same type.

 Improper use or replacement of the battery may

result in explosion hazard. Replace with the same or
equivalent type only. Dispose of used batteries
according to the instructions provided by the battery
manufacturer.

 If the product does not work properly, please

contact your dealer or the nearest service center.
Never attempt to disassemble the camera yourself.
(We do not assume any responsibility for problems
caused by unauthorized repair or maintenance.)