v2.0 11/1/10
1
INSTALLATION MANUAL©
ST-D420IR3.6
Dome Infrared CCD Camera
Copyright North American Cable Equipment, Inc.
v2.0 11/1/10
2
PACKAGE CONTENTS
This package contains:
One ST-D420IR3.6 Dome Infrared CCD camera
One installation manual
Note: The ST-D420IR3.6 requires a 12VDC 400mA power supply such as the ST-PS12VDC1A or
ST-PS12VDC2A.
PRODUCT DESCRIPTION
The ST-D420IR3.6 is an indoor infrared camera designed around a 1/3” Color SONY Super HAD
CCD with 420TVL of resolution, 24 infrared LEDs providing infrared capability up to 65 feet. The
ball style dome camera provides the installer with the ability to easily adjust the camera’s viewing
area. The ST-420IR3.6 is cost effective indoor surveillance solution for any budget.
SPECIFICATIONS
ST-D420IR3.6
Specifications (Typical)
1. Image Sensor
1/3” SONY Super HAD CCD
2. Pixels (HxV)
510x492
3. Scanning System
NTSC
4. Horizontal Resolution
420TV Lines
5. Synchronization
Internal
6. Minimum Illumination
0Lux (IR LED on)
7. Electronic Shutter
1/60~1/100,000 Seconds
8. Gain Control
Automatic
9. Lens
Board Lens 3.6mm/F2.0
10. S/N Ratio
≥48dB
11. IR LED
φ5x24PCS
12. IR Viewing Distance
49 – 65 feet
13. Gamma Correction
0.45
14. Video Output
1.0Vp-p/75Ω
15. Operation Temperature
14° - 113°F
16. Power Supply
DC12V 400mA
17. Dimensions
3.7”x2.7”
18. Weight
8.8 oz
19. Protection Grade
No
v2.0 11/1/10
3
INSTALLATION AND OPERATION
1. UNPACKING and HANDLING
Each unit is shipped assembled and factory tested.
Ensure that all accessories are removed from the container before discarding packing material
2. MECHANICAL INSPECTION
Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is
clean, and no connectors are broken, damaged, or loose. If equipment appears to be
damaged or defective please contact your distributor or SecurityTronix at 1-610-429-1511 for
assistance.
3. SPECIAL ATTENTION
a. The installer must comply with electrical safety standards. There must be sufficient
space between the camera’s power supply and video line and any high voltage
equipment and/or cables.
b. To help ensure the camera’s life and proper operation do not point the camera
towards the sun or strong light.
c. Do not install the camera in an environment where the temperature is above 113° F.
The camera should be installed in a cool and spacious environment.
d. Do not install the camera near a magnetic field or a high-power motor.
e. Only use a dry cloth to clean the camera. If there is dirt that is difficult to remove wipe
gently with a mild detergent. Never use strong or abrasive detergents.
f. A 12VDC 400mA power supply must be used. AC power cannot be applied. Using a
power supply other than 12VDC 400mA will damage the camera.
g. Only qualified installers are allowed to install, test and disassemble the camera.
h. The IR LED angle and lens viewing range are adjusted at the factory. Any change to
the camera’s lens will affect image quality.
i. The camera is a low voltage product. If installed outdoors proper safety and lightning
grounding are required.
4. WIRING CONNECTIONS
a. Connect the power supply’s DC plug to the camera’s power outlet.
b. Connect the camera to the monitor with a 75Ω coaxial video cable.
c. Connect power supply’s AC plug to a suitable AC power outlet.
d. Adjust the lens direction according to the required surveillance area and environment.
v2.0 11/1/10
4
5. TROUBLESHOOTING
a. No picture after applying power – (i) check all plugs and cables are securely
connected to the proper connectors; (ii) ensure your power supply is providing the
correct voltage and current.
b. The picture has ripples – (i) check to see if the power supply is experiencing AC ripple,
if so a filter may be required; (ii) determine if the monitor is faulty; (iii) determine if
other peripheral equipment is causing ripple and if so make the necessary
adjustments.
c. The picture background continuously changes color – a fluorescent lamp’s magnetic
field may cause color roll, therefore, reduce the number of fluorescent lamps or
increase the distance between the camera and the lamps.
d. The picture appears smeared – (i) the power supply voltage level may be unstable,
therefore, try another power supply; (ii) ensure the cables are correctly connected
and/or the cables are of the correct impedance.
e. Other interference may require a SecurityTronix ground loop isolation filter.
f. Additional troubleshooting assistance can be found on-line at www.securitytronix.com
in addition to support from SecurityTronix sales engineers at 1-610-429-1511.
Loading...