Securitytec DS-8016HCI-S, DS-8016HDI-S, DS-8004HDI-S, DS-8008HDI-S, DS-8004HDI-SL User Manual

...

Download

Colossal PRO DVR

DVRCOL16PRO

User Manual

4, 8 & 16 channel models

Advance H.264 Digital recorder

Index

Safety Precautions ............................................................................................................... 5

Chapter1 Product Introduction ....................................................................................... 8

1.1 Summary ...................................................................................................................... 8

1.2 Model Description ........................................................................................................ 8

1.3 Features ........................................................................................................................ 9

1.4 Typical Application .................................................................................................... 11

Chapter2 Installation .................................................................................................... 12

2.1 Check DVR and its Accessories ................................................................................. 12

2.2 HDD Installation ........................................................................................................ 12

Installing SATA HDD .................................................................................................... 12

2.3 DS-8000HCI-S Rear Panel Connection ..................................................................... 18

2.4 DS-8000HDI-S Rear Panel Connection ..................................................................... 20

2.5 DS-8000HDI-SL Rear Panel Connection ................................................................... 21

2.6 DS-8000HFI-S Rear Panel Connection ...................................................................... 23

2.7 DS-8000HSI-S Rear Panel Connection ...................................................................... 25

2.8 DS-8000HTI-S Rear Panel Connection ..................................................................... 27

2.9 External Alarm In/Out Connection ............................................................................ 29

Chapter3 Operational Instructions ............................................................................... 31

3.1 DVR Front Panel ........................................................................................................ 31

3.2 IR Control .................................................................................................................. 33

3.3 OSD Menu Description .............................................................................................. 35

3.3.1 Main Menu Items ............................................................................................. 35

3.3.2 Navigating Menus in DS8000 series DVR................................................... 36

3.3.3 Menu Operation ............................................................................................... 40

3.4 Character Input ........................................................................................................... 42

Chapter4 Basic Operation Guide ................................................................................. 43

4.1 Power on .................................................................................................................... 43

4.2 Live View ................................................................................................................... 44

4.3 Login .......................................................................................................................... 47

4.4 PTZ Control .............................................................................................................. 48

4.5 Manual Record ........................................................................................................... 50

4.6 Playback ..................................................................................................................... 52

4.7 Backup Recorded Files .............................................................................................. 57

4.8 Powering Down the DVR .......................................................................................... 60

Chapter5 Main and Spot Output .................................................................................. 62

5.1 Main and Spot Output ................................................................................................ 62

5.2 Main and Spot Output Live View ............................................................................... 63

5.3 Main and Spot Output Playback ................................................................................. 65

5.4 Main and Spot Output to Control PTZ ....................................................................... 65

Chapter6 Advanced Operation Guide ......................................................................... 66

6.1 User Management ...................................................................................................... 67

6.1.1 Add Users ......................................................................................................... 67

6.1.1 Add Users ......................................................................................................... 68

6.1.2 Delete User ...................................................................................................... 69

6.1.3 Password Modification ................................................................................... 70

6.1.4 User Rights....................................................................................................... 71

6.2 Device ID ................................................................................................................... 73

6.3 Video Standard and VGA Setup ................................................................................ 74

6.4 Date and Time Setup .................................................................................................. 75

6.4.1 Daylight Saving Time Setup .......................................................................... 77

6.5 Image Setup ................................................................................................................ 78

6.5.1 Camera Name Setup ...................................................................................... 78

6.5.2 Video Parameter Setup .................................................................................. 79

6.6 Mask Area Setup (Privacy Mask) ............................................................................... 81

6.7 View Tampering Alarm .............................................................................................. 83

6.8 Video Loss Alarm ....................................................................................................... 85

6.9 Motion Detection Alarm............................................................................................. 86

6.10 Live View Setup ......................................................................................................... 90

6.11 Recording Setup ......................................................................................................... 91

6.12 Alarm I/O Setup ......................................................................................................... 96

6.13 Network Setup .......................................................................................................... 100

6.13.1 Network Settings ............................................................................................ 100

6.13.2 DHCP Function .......................................................................................... 103

6.13.3 PPPoE Function ........................................................................................ 103

6.13.4 IP Server Solution for DHCP ................................................................... 104

6.14 PTZ Setup ................................................................................................................ 105

6.14.1 PTZ Connection ........................................................................................ 105

6.14.2 PTZ Settings .............................................................................................. 105

6.14.3 PTZ Control ................................................................................................ 107

6.14.4 Preset Setup .............................................................................................. 107

6.14.5 Sequence Setup ........................................................................................ 109

6.14.6 Cruise (Pattern) Setup: ............................................................................ 110

6.15 RS232 Setup ............................................................................................................. 111

6.15.1 Console Mode ........................................................................................... 111

6.15.2 Transparent Channel Mode ..................................................................... 111

6.15.3 PPP Mode .................................................................................................. 111

6.16 Exceptions Setup ...................................................................................................... 116

Chapter7 Utilities ........................................................................................................ 118

7.1 Restore Parameters ................................................................................................... 119

7.2 Hard Disk Management ........................................................................................... 119

7.3 Clear Alarm Out ....................................................................................................... 120

7.4 Reboot ...................................................................................................................... 120

7.5 Power Off ................................................................................................................. 120

7.6 View Log .................................................................................................................. 120

7.7 System Information .................................................................................................. 123

Chapter8 Firmware Upgrade ..................................................................................... 124

8.1 Upgrade from USB Flash ......................................................................................... 124

8.2 Upgrade from CD ..................................................................................................... 124

8.3 Upgrade from FTP Server ........................................................................................ 125

8.3.1 FTP Server Setup ......................................................................................... 125

8.3.2 Use DVR FTP Upgrade Function ............................................................... 127

8.3.3 Use RS-232 Serial Command ..................................................................... 127

8.4 Use Client Software to Upgrade ............................................................................... 130

Appendix A HDD Capacity Calculation ......................................................................... 131

Appendix B DVR Connector Definition .......................................................................... 132

Appendix C Specifications ............................................................................................. 138

Appendix D Quick Search.............................................................................................. 144

Appendix E Troubleshooting ......................................................................................... 146

Appendix F Product Service .......................................................................................... 148

Appendix G Customer Information Card ....................................................................... 149

Safety Precautions

Caution:

To reduce the risk of electric shock, please do not remove the cover. There are no user-serviceable parts inside, please contact us directly for repairing.

Important Safeguards:

1. Go through these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or third prong is provided for your safety. If the provided plug does not fit into the outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use of a cart, stand, or table is typical for temporary installations to test and demonstrate products. Use extreme caution to ensure that the product is not subjected to shock or vibration. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Permanent installation

requires a solid mounting surface for equipment with no movement or vibration.

13. Unplug this unit during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Moving - Disconnect the power before moving the unit. The unit should be moved with care. Even moderate force or shock may result in damage to the unit and the hard disk drives.

16. Power Sources - This unit should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply you plan to use, consult your appliance dealer or local power company.

17. Overloading - Do not overload outlets and extension cords as this can result in a risk of fire or electric shock.

18. Object and Liquid Entry - Never push objects of any kind into this unit through openings, as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the unit.

19. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

20. Coax Grounding - If an outside cable system is connected to the unit, be sure the cable system is grounded. U.S.A. models only--Section 810 of the National Electrical Code, ANSI/NFPA No.70-1981, get information from professional electrician to proper grounding of the mount and supporting structure, grounding of the coax to a discharge unit, size of grounding conductors, location of discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

21. To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain or moisture and objects filled with liquids, such as vases, should not be placed on

this apparatus.

22. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of the replaced battery in an environmentally friendly way.

Cleaning:

You can clean the unit with a moist lint-free cloth or chamois leather cloth.

Warning:

This device is intended for use in public areas only. Surreptitious recording of oral

communications may be prohibited by local law.

Unpacking:

Check the package for visible damage. If any items appear to have been damaged in shipment, notify the shipping company. Unpack carefully. This is electronic equipment and should be handled with care to prevent damage to the unit. Do not attempt to use the unit if any components are damaged. If any items are missing, notify the dealer.

The shipping carton is the safest container in which to transport the unit. Save it and all packing materials for future use. If the unit must be returned, use the original packing materials.

Packaging contents:

The package should contain the following items:

1. Digital Video Recorder

2. Accessories box

Chapter1 Product Introduction

1.1 Summary

DS-8000 series Network Digital video Recorder is an excellent digital surveillance product. It adopts embedded MCU (Microprocessor Control Unit) and an embedded Real-Time Operating System (RTOS), combining the most advanced technology in the Information Industry such as video and audio encoding/decoding, hard disk recording and TCP/IP transmission. The firmware is burned into a flash memory, which makes it more stable and reliable than software programs that run from a standard disk drive.

DS-8000 series combines features of both Digital Video Recorder (DVR) and Digital Video Server (DVS). It is widely applied as a stand-alone unit or a part of a powerful surveillance system.

1.2 Model Description

Note: This model name includes all the DS-8000 series, a real model name is just part of

it.

1.3 Features

Compression:

 Supports up to 16 video channels (NTSC/PAL). Each channel is independent,

H.264 hardware compression and real-time (NTSC 30FPS, PAL 25FPS). Supports both variable bit rate and variable frame rate

 Supports up to 16 channels audio input channels. Each channel is independent

OggVorbis compression and the bit rate is 16Kbps

 Compressed video and audio are synchronous. You can select either mixed

stream (video and audio) or video only.

 Supports 4CIF, DCIF, 2CIF, CIF and QCIF resolution.

 Supports multi area motion detection

 Supports OSD and changeable OSD position

 Supports LOGO and changeable LOGO position

Local functions:

Record:

 Supports multiple record methods including real-time, manual record, motion

detection, external alarm, motion&alarm and motion|alarm

 Supports up to 8 HDDs. Each HDD can support 2000GB maximum

 Supports FAT32 file system

 Supports HDD S.M.A.R.T technology

 Supports continuous (overwrite) and linear (stop when full) record modes

 Supports backup of recorded files and video/audio clips. Supports USB memory

stick (thumb drive), USB HDD, USB CD-R/W, USB DVD-R/W and SATA HDD for backup

Preview and playback:

 Supports BNC analog monitor and VGA output for main output

 Supports one spot video and spot audio output

 Supports multiple live view modes

 Supports Privacy Mask (blank portions of camera views)

 Supports camera block alarm

 Supports 2-ch synchronous playback. Support play forward, backward, pause,

frame by frame, etc

 Supports play back by files or by time/date

 Displays local record status

PTZ:

 Supports multiple PTZ protocols

 Supports preset, sequence and pattern

Alarms:

 Supports exception alarm, motion detection alarm, external alarm, etc

Miscellaneous:

 Supports IR Remote control

 Supports RS-485 keyboard

 Support multi-level user management

Network:

 Supports TCP, UDP, RTP, Multicast for network viewing

 Support PPPoE for broad band dialup

 Support DDNS

 Support E-mail

 Support NTP

 Supports PSTN for standard dialup

 Supports remote parameters setup

 Alarm information can be sent to remote center

 Network controlled PTZ

 Network recording of video/audio

 Network download and playback of recorded files from the DVR

 Remote upgrade of DVR firmware

 RS-232 supports transparent channel function so that the remote PC can use

DVR to control serial devices

 Supports bi-directional audio or one-way audio broadcast

 Supports IE to view and configure the DVR

 Supports activity log.

Development support:

 Provide network SDK (Software Development Kit)

 Provide client demo source code

1.4 Typical Application

Chapter2 Installation

2.1 Check DVR and its Accessories

Please follow the packing list in the packing box and carefully check the contents of the shipping container. If any of the items is missing, please contact your dealer.

2.2 HDD Installation

The DVR is without HDD when leaving factory. Based on the record schedule, you can calculate the total capacity you need (refer to Appendix A). Please ask the specialist to disassembly the DVR and install HDD.

Installing the hard disks must be performed by qualified personnel. Unauthorized installation of hard disks may result in permanent damage of the disk and the recorder, and is performed at your own risk.

Caution:

When working with electrostatic sensitive devices such as a hard disk or the DVR unit, make sure you use a static-free workstation. Any electrostatic energy coming in contact with the hard disk or DVR main board can damage it permanently.

Installing SATA HDD

1. Before installation of the HDD, switch the recorder off and unplug the power cable.

2. Place the recorder on a flat table, and make sure you take proper ESD precautions.

Wear an ESD bracelet at all times. A Philips screwdriver is required to disassemble and reassemble the unit.

3. Remove the metal top cover by removing two screws from the rear of the cover, slide the

cover towards the rear and lift it from the unit.

4. Remove the metal hard drive brackets (remove one screw from the top of the mounting

plate, lift the rear of the plate and slide backwards). To remove the bottom plate, remove the mounting screws that are inserted from the outside of the unit (one on each side). Make sure that the hard disk bracket does not come into contact with the PCB, as this could cause damage.

5. Place the hard disks you wish to install on the flat table with the mounting side facing

up.

6. Place the metal hard disk bracket on top of the hard disks, and fasten each hard disk

with 4 screws to the bracket.

7. Reinstall the bracket and then connect the power and data cables to the HDD and main board.

8. Check all connections, and reinstall the metal cover on the DVR.

9. Connect the power cable and power on the DVR.

10. Press [MENU] key to enter into DVR main menu. Go to the "Utilities" menu and choose "Hard disk" to format the hard disks. Check that all installed disks are detected by the DVR (shown in the menu). Choose "Format" and select "All" to format all hard disks. When all drives are formatted a confirmation message will be shown on the screen. Ensure that all installed disks have the status "OK".

Hard drive installation is complete.

2.3 DS-8000HCI-S Rear Panel Connection

DS-8004HCI-S Rear Panel:

Index

Physical Interface

Description

Video input

Standard BNC

Audio input

Standard BNC

Main video output

Connect CCTV monitor, output video and menu

Main audio output

Local audio output

Line in

Audio line input for voice talk

USB interface

USB memory disk, USB HDD, USB CD/DVD or USB mouse

VGA interface

VGA display

Keyboard interface

One is for DS-1000KI keyboard, and the other is for DVR cascade. Using Pin3 and Pin4

RS-232

Connect RS-232 devices. Refer to Appendix B for pin definition

Network Interface

Connect network devices. Refer to Appendix B for pin definition

SW1

RS-485 terminal resistor switch. Default is off. The resistor is 120Ω

RS-485

PTZ connection. Using T+/T- to connect PTZ

Alarm input

4 sensor alarm in

Relay output

2 relay outputs

GND

Ground

AC Input

100~240VAC

E-SATA

Optional. Extend 1st internal SATA to E-SATA.

DS-8008HCI-S, DS-8016HCI-S Rear Panel:

Index

Physical Interface

Description

Video input

Standard BNC

Audio Input

Standard BNC

Spot video output

Spot monitor for live video and playback

Spot audio output

Spot monitor for live audio and playback

Main video output

Main monitor for live video playback and menu

Main audio output

Main monitor for live audio and playback

Line in

Line input for audio

VGA interface

VGA display

RS-232

Connect RS-232 devices. Refer to Appendix B for pin definition

Network interface

Connect network devices. Refer to Appendix B for pin definition

USB Interface

USB flash memory, USB HDD, USB CD/DVD or USB mouse

E-SATA

Optional. Extend 1st internal SATA to E-SATA.

SW1

RS-485 terminal resistor switch. Default is off. The resistor is 120Ω

RS-485

PTZ connection. Using T+/T- to connect PTZ.

Keyboard interface

Using D+/D- for keyboard and DVR cascade connection.

Alarm input

16 sensor alarm in

Relay output

4 relay outputs

GND

Ground

AC input

100~240VAC

2.4 DS-8000HDI-S Rear Panel Connection

DS-8004HDI-S, DS-8008HDI-S, DS-8016HDI-S Rear Panel:

Index

Physical Interface

Description

Video input

Standard BNC

Audio Input

Standard BNC

Spot video output

Spot monitor for live video and playback

Spot audio output

Spot monitor for live audio and playback

Main video output

Main monitor for live video playback and menu

Main audio output

Main monitor for live audio and playback

Line in

Line input for audio

VGA interface

VGA display

RS-232

Connect RS-232 devices. Refer to Appendix B for pin definition

Network interface

Connect network devices. Refer to Appendix B for pin definition

USB Interface

USB flash memory, USB HDD, USB CD/DVD or USB mouse

E-SATA

Optional. Extend 1st internal SATA to E-SATA.

SW1

RS-485 terminal resistor switch. Default is off. The resistor is 120Ω

RS-485

PTZ connection. Using T+/T- to connect PTZ.

Keyboard interface

Using D+/D- for keyboard and DVR cascade connection.

Alarm input

16 sensor alarm in

Relay output

4 relay outputs

GND

Ground

AC input

100~240VAC

2.5 DS-8000HDI-SL Rear Panel Connection

DS-8004HDI-SL, DS-8008HDI-SL, DS-8016HDI-SL Rear Panel:

Index

Physical Interface

Description

Video input

Standard BNC

Loop output

Standard BNC

Audio input

Standard BNC

Spot video output

Spot monitor for live video and playback

Spot audio output

Spot monitor for live audio and playback

Main video output

Main monitor for live video playback and menu

Main audio output

Main monitor for live audio and playback

Line in

Line input for audio

VGA interface

VGA display

RS-232

Connect RS-232 devices. Refer to Appendix B for pin definition

Network interface

Connect network devices. Refer to Appendix B for pin definition

USB Interface

USB flash memory, USB HDD, USB CD/DVD or USB mouse

E-SATA

Optional. Extend 1st internal SATA to E-SATA.

SW1

RS-485 terminal resistor switch. Default is off. The resistor is 120Ω

RS-485

PTZ connection. Using T+/T- to connect PTZ.

Keyboard interface

Using D+/D- for keyboard and DVR cascade connection.

Alarm input

16 sensor alarm in

Relay output

4 relay outputs

GND

Ground

AC input

100~240VAC

2.6 DS-8000HFI-S Rear Panel Connection

DS-8004HFI-S Rear Panel:

LINE IN

AAUX

VAUX

VGA

RS-232 UTP

70706060606040404040

230

7070

4 5 6

KEYBOARD

VOUT

AOUT

3 4 G G

2 G G G

1 G

1 2 ON

↓

SW1

2 3 41

VIN

AIN

RS-485

T+ T- R+R-

OUT

ALARM

ESATA

Index

Physical Interface

Description

Video input

Standard BNC

Audio input

Standard BNC

Main video output

Main monitor for live video, playback and menu.

Main audio output

Local audio output

Spot video output

Spot monitor for Live video and playback

Spot audio output

Spot monitor for live audio and playback

Line in

Line input for audio

USB interface

USB flash memory, USB HDD, USB CD/DVD or USB mouse

VGA interface

VGA display

Keyboard interface

One is for DS-1000KI keyboard, and the other is for DVR cascade. Using Pin3 and Pin4

RS-232

Connect RS-232 devices. Refer to Appendix B for pin definition

Network interface

Connect network devices. Refer to Appendix B for pin definition.

SW1

RS-485 terminal resistor switch. Default is off. The resistor is 120Ω.

RS-485

PTZ connection. Using T+ T- to connect PTZ

Alarm input

4 sensor alarm in

Alarm output

2 relay outputs

GND

Ground terminal

AC input

100~240VAC

E-SATA

Optional. Extend 1st internal SATA to E-SATA.

DS-8008HFI-S, DS8016HFI-S Rear Panel:

Index

Physical Interface

Description

Video input

Standard BNC

Audio input

Standard BNC

Spot video output

Spot monitor for live video and playback

Spot audio output

Spot monitor for live audio and playback

Main video output

Main monitor for live video, playback and menu

Main audio output

Main monitor for live audio and playback

Line in

Line input for audio

VGA interface

VGA display

RS-232

Connect RS-232 devices. Refer to Appendix B for pin definition

Network interface

Connect network devices. Refer to Appendix B for pin definition

USB interface

USB memory disk, USB HDD, USB CD-R/W, USB DVD or USB mouse

E-SATA

Optional. Extend 1st internal SATA to E-SATA.

SW1

RS-485 terminal resistor switch. Default is off. The resistor is 120Ω

RS-485

PTZ connection. Using T+/T- to connect PTZ

Keyboard Interface

Using D+/D- for keyboard and DVR cascade connection

Alarm input

16 sensor alarm in

Relay output

4 relay outputs

GND

Ground

AC Input

100~240VAC

2.7 DS-8000HSI-S Rear Panel Connection

DS-8004HSI-S rear panel

LINE IN

AAUX

VAUX

VGA

RS-232 UTP

70706060606040404040

230

7070

KEYBOARD

VOUT

AOUT

2 3 4 G G

2 G G G

1 G

1 2

SW1

2 3 41

VIN

RS-485

T+T- R+R-

OUT

ALARM

ESATA

↓

LOOP

5 6

7 8 9

Index

Physical Interface

Description

Video Input

Standard BNC.

Video Loop out

Standard BNC.

Main video Output

Connect CCTV monitor, output video and menu.

USB Interface

USB flash memory, USB HDD, USB CD/DVD writer, or USB mouse

VGA interface

VGA display.

Keyboard interface

One is for DS-1000KI keyboard, and the other is for DVR cascade. Using Pin3 and Pin4.

RS-232

Connect RS-232 devices.

Ethernet

Connect network devices.

SW1

RS-485 terminal resistor switch. Default is off. The resistor is 120 Ω.

RS-485

PTZ connection. Using T+ T- to connect PTZ.

Alarm input

4 sensor alarm in.

Alarm output

2 replay output.

GND

Ground terminal

AC input

100~240VAC

E-SATA

Optional. Extend 1st internal SATA to E-SATA.

DS-8008HSI-S DS-8016HSI-S rear panel

1 2 ON

1 2 3 4 5 6 7 8

10 11 12 13 14 15 16

VIN

LOOP

OUT

VOUT

AOUT

AUX

VOUT

AOUT

LINE IN

SW1

VGA

RS-232ETHERNET

G G D+ D-

RS-485 KB IN

OUT

1 G 2 3 G 4 GG0 G

ALARM

1 2 3 4 5 6 7 8 9 10

11 12 1314 1516

T+T- R+

G G

70706060606040404040

230

7070

ESATA

2 3 4

6 7

Index

Physical Interface

Description

Video Input

Standard BNC.

Video loop out

Standard BNC.

Aux audio Output

Spot monitor for audio preview and playback.

Main video output

Main monitor for video and menu.

VGA Interface

VGA display.

RS-232

Connect RS-232 devices. Refer to Appendix B for pin definition.

Ethernet

Connect network devices. Refer to Appendix B for pin definition.

E-SATA

Optional. Extend 1st internal SATA to E-SATA.

SW1

RS-485 terminal resistor switch. Default is off. The resistor is 120Ohm.

RS-485

PTZ connection. Using T+/T- to connect PTZ.

Keyboard Interface

Using D+/D- for keyboard and DVR cascade connection.

External Alarm Input

16 sensor alarm in.

Relay Output

4 replay output.

GND

Ground

AC Input

100~240VAC

USB

USB interface is on the front panel

2.8 DS-8000HTI-S Rear Panel Connection

DS-8004HTI-S, DS-8008HTI-S, DS-8016HTI-S Rear Panel:

Index

Physical Interface

Description

Video input

Standard BNC

Audio Input

Standard BNC

Spot video output

Spot monitor for live video and playback

Spot audio output

Spot monitor for live audio and playback

Main video output

Main monitor for live video playback and menu

Main audio output

Main monitor for live audio and playback

Line in

Line input for audio

VGA interface

VGA display

RS-232

Connect RS-232 devices. Refer to Appendix B for pin definition

Network interface

Connect network devices. Refer to Appendix B for pin definition

USB Interface

USB flash memory, USB HDD, USB CD/DVD or USB mouse

E-SATA

Optional. Extend 1st internal SATA to E-SATA.

SW1

RS-485 terminal resistor switch. Default is off. The resistor is 120Ω

RS-485

PTZ connection. Using T+/T- to connect PTZ.

Keyboard interface

Using D+/D- for keyboard and DVR cascade connection.

Alarm input

16 sensor alarm in

Relay output

4 relay outputs

GND

Ground

AC input

100~240VAC

2.9 External Alarm In/Out Connection

Alarm input dry contact:

Alarm output connection:

Connect with DC device

Connect with AC device.

Alarm input port (dry contact): G (GND): Connect the GND of sensor.

1~8: Alarm input, support normal open/normal close.

0: Reserved.

Alarm output: 1G~4G: 4 relay output.

Powering Up:

Note: Complete all cable connections before powering on the DVR.

1. Switch on all connected equipment.

2. Connect the power cable to the unit.

3. Switch on the power supply power switch.

Chapter3 Operational Instructions

3.1 DVR Front Panel

  

   

Index

Type

Name

Description

IR receiver

Camera indicator Lamps

1 - 16

Show 1-16 camera status. Green means recording; Red means network transmission; Orange means recording and network transmission.

POWER

Device switch with power indicator lamp. Green means DVR is operating; Red means DVR is powered off; No light means no power is supplied.

Status Lamps

READY

DVR is ready

STATUS

Green means you can use IR remote control

ALARM

Red means there is alarm

Modem

Green means there is a modem connection.

HDD

Flickering red means reading or writing HDD

LINK

Green means there is a network connection

Tx/Rx

Flickering green means data is being transmitted

Input keys

Numeric Keys

Input number, lower case, upper case character and symbols F1

[LIGHT] in PTZ control

[AUX] in PTZ control

Function keys

1. Enter Menu (from live mode)

2. Wiper control in PTZ mode

3. Press and hold [MENU] for 5 seconds to cancel key-down tone

ESC

Cancel and return to previous menu

PLAY

1. Local playback

2. [AUTO] in PTZ control

REC

1. Manual record

2. Preset in PTZ mode

EDIT

1. In edit state, delete the current cursor character

2. [IRIS+] in PTZ mode

3. Select  or × to enable or disable

PTZ

1. Enter into PTZ control mode

2. [IRIS-] in PTZ mode

1. Input character select (number, lower case,

upper case and symbol)

2. [FOCUS+] in PTZ mode

3. Display or hide the channel status bar (in live

mode)

1. Multi screen selection

2. Switch menu mode into live view

3. [FOCUS-] in PTZ mode

INFO

[ZOOM+] in PTZ mode

Main/Aux

1. Switch main/spot video output control mode

2. [ZOOM-] in PTZ mode

Control Keys

Direction Keys

Composed of [] , [], [] and []

1. Menu mode, use direction keys to select, press

[Enter] or [Edit] key for edit

2. PTZ direction control

3. Playback speed control

ENTER

1. Menu confirmation;

2. Select  or × to enable or disable;

3. Pause playback.

3.2 IR Control

Index

Name

Description

POWER

Power DVR on/off

DEV

Enable/Disable IR remote control

Numeric Keys

Same as numeric keys on front panel

EDIT

Same as [EDIT] key on front panel

5 A Same as [A] key on front panel

REC

Same as [REC] key on front panel

PLAY

Same as [PLAY] key on front panel

INFO

Same as [INFO] key on front panel

VOIP

Same as [Main/Aux] key on front panel.

Same as [MENU] key on front panel.

Same as [PREV] key on front panel.

Direction Keys ENTER

Same as direction keys and enter key on front panel

PTZ

Same [PTZ] key on front panel

ESC

Same as [ESC] key on front panel

Reserved

Reserved for future use

Same as [F1] key on front panel

Lens control

IRIS, FOCUS ZOOM for lens control

Same as [F2] key on front panel

Loading the batteries into the IR controller:

1. Remove the battery cover.

2. Insert the battery. Ensure that the poles (+ and -) are correctly positioned.

3. Replace the battery cover.

Enable the IR Remote Controller:

1. Press the [DEV] key, input the DVR device ID (default is ―88‖. It can be changed in the ―Display‖ menu) and then press the [ENTER] key.

2. The ―STATUS‖ lamp on the DVR front panel will turn green, indicating that you can use IR controller to operate the DVR.

Disable the IR controller:

1. When IR controller status lamp is on, press the [DEV] key.

2. The ―STATUS‖ lamp on the DVR will turn off. The IR controller won’t control the DVR.

Turn off the DVR:

1. When IR controller status is on, press the [POWER] key for several seconds.

2. The DVR will be powered off.

Troubleshooting the IR Remote:

1. Always aim the IR Remote controller at the DVR you want to control.

2. Make sure that the correct DVR ID code is entered and the status lamp on the DVR is green.

3. Check the batteries.

4. Make sure nothing is obstructing the IR sensor on the DVR.

5. Try another IR Remote control.

Note: If you have only one Remote unit to work with it is often difficult to verify whether the

unit is actually working. Humans can’t see the IR LED flashing on the remote when keys are pressed. Cameras can see the LED flash. Aim the Remote at a conveniently placed camera and you can see the LED lash on the monitor.

3.3 OSD Menu Description

3.3.1 Main Menu Items

Menu Name

Function

Menu Name

Function

Display

Unit Name Device ID Require Password Y/N Screen saver Video standard Enable Scaler Brightness Menu transparency VGA resolution DST Date and Time

Image

Select Camera Camera name and position Brightness,Contrast,Hue, Saturation adjust OSD Display mode, position and OSD style setup Privacy Mask area setup View tampering area and response setup Video signal loss Motion detection sensitivity, area and response setup

Recording

Overwrite/Stop recording SATA1 disk usage Recording parameters Record schedule Prerecord time Post Record time

Network

DVR IP address DNS IP Advanced settings Multicast IP address Remote host IP and port PPPoE setup E-mail

Alarms

Alarm input type (NO/NC) Alarm response and PTZ linkage Alarm output and schedule

Exception

Exception Handle Method

PTZ

PTZ parameters Preset setup Sequence setup Pattern setup

RS232

RS232 parameters

Preview

Out channel Preview mode Switch time Audio preview Alarm out Display delay,Lay out

User

Add or delete user Password setup User rights setup

Transact

Through mode Local port

Utilities

Save parameter Restore factory parameters Upgrade firmware HDD management Stop alarm output Reboot Power off View log System information

3.3.2 Navigating Menus in DS8000 series DVR

The Operation Manual provides step by step instructions in the early chapters. The later chapters provide directions without indicating some of the individual key presses because you will have learned the basics by then. This section provides a brief overview of navigating through the menus using the control keys and by using the mouse. With this information you will be able to quickly access most DVR functions. See the detailed text for further information on particular features. There are several methods to control the DVR.

 Front Panel Control.  IR Remote Control.  Mouse Control.  Remote Software Control.

The details in the manual concentrate on the Front Panel control method. The IR Remote control operation is essentially the same using the remote device. There are a few differences that are mentioned in the manual. Mouse control is an option that can be used, but is not mentioned throughout the manual. The remote software is addressed in a separate manual.

Mouse Control: There are some things to consider when using a mouse with the DVR. A USB mouse is used. There is one USB connection on the rear panel of the DVR. A USB port expander may be used to add additional USB connectivity to the DVR. This could be helpful in exporting files to a USB device and when updating the firmware. Do not place a mouse pad on the top cover of the DVR as this may block the access holes and cause air flow restriction and heat buildup that may cause damage to the unit.

Most DVR operations can be performed using the mouse. If you are close enough to the unit to use a mouse you will also be able to use the front panel and IR Remote keys for operation. You will decide which operations are more easily performed with

each control method.

In Live View control:

Double click the left mouse key on an individual camera cameo in a multi-screen display to go to full screen. Double click again to return to the previous multi-screen display. A right mouse click produces a pop-up menu that provides access to a large number of features.

 Main Menu: Provides access to the DVR Menu.  Single: Allows selection of any full size camera display.  Multi-Preview: Select ―Live View‖ of 4, 9, 12, or 16 channel multi-screen

modes.

 Next Preview: Selects the next sequential display (ex. In four-channel: 1-4,

5-8, etc.).

 PTZ Control: Access PTZ camera control.  Play: Enter playback mode.  Manual Record: Access the Manual Record Menu.  Close Status: (Open status): Show/hide the status line on the monitor.  Switch VOUT: Switch to the ―Spot‖ monitor output.

Caution: If you select ―Switch VOUT‖ you will lose mouse control of the main monitor. The mouse pointer will move to the Spot display. If you have a monitor connected to

the ―Spot‖ output you can right click and select ―Switch VOUT‖ to return to the main display control. If no ―Spot‖ monitor is available you will not be able to return to the main output using the mouse. You must press the ―Main/Aux‖ key on the front panel, or the ―VOIP/MON‖ key on the IR Remote. The same issue is present when using

front panel and IR Remote operation. If the Spot monitor is inadvertently selected (by pressing the appropriate key) when there is no Spot monitor installed, it will appear as if the unit is not operating properly.

General Mouse Menu Navigation: A standard left mouse click will select most

options. Just position the mouse over the desired menu item and select. A ―right mouse click‖ pops-up an option list (from the live display). Once in the menu, a right

click will take you to the previous menu. Walk through the following list of items to familiarize yourself with mouse operation. Starting from the live display:

 ―Right-click‖ the mouse to view the control options and then and select ―Main

Menu.‖

 You can click on any of the options to enter sub menus.  Click to select the Display Menu and view the available options.  Additional mouse clicks will select any menu option and/or change the status of

the check boxes.

 Select the ―Setup‖ button next to time/date. You are now in a ―Sub, Sub menu.‖

 Click on the ‖Day‖ window next to ―Date.‖ The pop up box allows you to change

the number entry. Just click on the numbers you want (don’t forget leading zeros).

 Always remember to navigate to the ―Confirm‖ button and press ―Enter‖ to update

your selections. Otherwise the selections will not be updated.

 A ―right click‖ will take you back to the previous menu; first to the ―Display‖ menu,

another ―Right click‖ to the Main Menu and another takes you back to the live

display.

There are some situations where mouse operation may seem erratic (especially if you use the scroll button) but a little practice can make this a preferred method for controlling the DVR.

Control from the Front Panel Keys:

Front Panel: All DVR functions are controllable from the front panel keys. Reaching the

front panel may be difficult in some installations so the IR Remote is a good alternative when the DVR is in sight, but not in reach.

Function Keys:

 MENU: Enter the DVR Menu.  ESC: The escape key returns to Live mode, or to a previous menu.  PLAY: Enters Playback.  REC: Enters Manual Record Menu.  EDIT: Selects the next sequential display (ex. In four-channel: 1-4, 5-8, etc.)

in Live Mode. Change selections in Menu Mode.

 PTZ: Enter camera control mode. (All function buttons are used for PTZ

functions when in PTZ Mode. See the red titling under each key for its PTZ function). Press ―ESC‖ to exit PTZ mode and restore normal function key operation.

 A: Show/hide the status line on the monitor in Live Mode. Scroll through

character entry options in Menu Mode.

 PREV: Toggle ―Live View‖ of 1, 4, 9, 12, or 16 channel multi-screen modes.  MAIN/AUX: Toggle between Main monitor and Spot monitor control modes.

General Front Panel Key Menu Navigation: Press the ―Menu‖ key to enter the Main Menu. Moving the Active Window (highlighted cursor) is done by pressing the direction keys (Up, Down, Left, Right) and item selection is done with the ―Enter‖ (center of arrow keys) key (or the EDIT key). Once in the menu, ―ESC‖ will take you to the previous menu and back to live mode. Walk through the following list of items to familiarize yourself with key operation. Starting from the live display:

 Press the ―Menu‖ key to enter the ―Main Menu.‖  Use the Up/Down arrow keys to enter sub menus.  Select the Display Menu to view the available options.

 Use the arrow keys to move to selected menu options and press ―Enter‖ to select.

Enter (or, Edit) will also change check box selections.

 Select the ―Setup‖ button next to time/date. You are now in a ―Sub, Sub menu.‖  Select the ‖Day‖ window next to ―Date‖ (arrow keys, then Enter). Use the number

keys to enter your numerical selections and press ―Enter.‖

 Always remember to navigate to the ―Confirm‖ button and press ―Enter‖ to update

your selections. Otherwise the selections will not be updated.

 Press ―ESC‖ to take you back to the previous menu; first to the ―Display‖ menu,

―ESC‖ again to the Main Menu and again to return to the live display.

3.3.3 Menu Operation

How to access the menus:

 Press the [MENU] key to enter the DVR main menu  Press the [PLAY] key to enter the playback menu  Press the [REC] key to enter the manual record menu  Press the [PTZ] key to enter the PTZ control interface

Note: You must input a valid user name and password. The default user name is ―admin‖ and password is ―12345‖.

Main Menu Description:

Main menu:

One section of the menu screen will be highlighted to indicate the input cursor position. The Active window can be moved from one item to another by using the direction keys ([↑] [↓] [] []). When the ―Active Window‖ is located on an item, you can press the [ENTER] key to enter into the sub menu. For example: Move the ―Active Window‖ to ―Image‖ and press [ENTER] to enter into the secondary menu as follows:

Each sub-menu contains several related items. Select the entry desired.

1. Check Box: Provide 2 options. ―‖ means enable and ―×‖ means disable. Select either [ENTER] or [EDIT] to change selections.

2. List Box: Provides more than 2 options. However, only one of them can be selected. You can press [ENTER] or [EDIT] to enter into edit mode, then use

[↑] and [↓] to select one option. For example, on the right side of ―Select Camera‖, there is a list box for you to select one camera.

3. Edit Box: Allows you to input characters. Press the [EDIT] key to enter the edit mode. You can input characters as follows:

(1) Press the [A] key to select the entry mode (numbers, upper case, lower

case or symbols). (2) Use [] and [] keys to move the cursor. (3) Use the [EDIT] key to delete the character in front of the cursor. (4) Press [ENTER] or [ESC] to exit the edit mode.

4. Button: Execute a special function or enter into the next sub-menu. For example, press the ―Policy‖ button to enter into sub-menu. Press [Confirm] to save parameters and return to the previous menu. Press the [Cancel] key to cancel and return to previous menu. Grayed-out buttons indicate they can be operated only after another selection is enabled.

Exiting the Menu: Press [ESC] to exit the menu and return to live view mode.

3.4 Character Input

There is a status line at the bottom of all character entry screens. For example: In the ―camera name‖ edit box the following status line appears at the bottom of screen.

The word ‖Number‖ indicates that you can use the numeric keys to input numbers. Press the [A] key to change input modes. Available options are ―Number‖, ―Uppercase‖, ―Lowercase‖ and ―Symbol‖.

Uppercase

Lowercase

Symbol

There are 24 symbols in all. They are divided into 4 pages. Press the [0] key to scroll through the available selections.

Note: The character input scheme may seem difficult until you become familiar with its operation. All setup procedures may be accomplish from the remote software using a more familiar Windows format.

Chapter4 Basic Operation Guide

4.1 Power on

Note: It is always a good idea to check the power supply before connecting the AC

cable and applying power. The DS8000 is equipped with a universal power supply that will accommodate 120/240VAC, 50/60Hz. Units with an input power selector switch must be placed in the correct input voltage position for the local area before applying power. Switch the main power switch off before inserting the AC power cord. Connect a monitor (VGA, or composite) to view the GUI and setup the unit.

If the [POWER] lamp is off, please do as follows:

1. Make sure the power cord is connected to an active power source.

2. Switch on the power key on the real panel.

If the [POWER] lamp is red:

1. Press the [POWER] key to start the DVR.

2. The power lamp will turn green as the unit powers up.

3. The DSP and HDD initialization process will be shown on the monitor. The graphic includes two lines. The first line indicates the DSP hardware and the second lists the available drives installed. A check mark (√) indicates correct operation of the DSP and the presence of a disk drive installed in one of the eight

available drive locations. An ―X‖ indicates improper operation or an uninstalled

drive.

Note: If no drives are installed or detected, a ―No Disk‖ message will display.

4.2 Live View

At startup, the DVR will enter the live view mode. On the live display you will see the date/time, camera name and camera/alarm status line in addition to the video from attached (and configured) cameras. The information in the status line is described later in this manual. You can easily toggle the status line on/off by right clicking the mouse and selecting ―Show‖ or ―Close‖ status, or press the ―A‖ key on the DVR front panel or IR Remote.

On the live screen, you will see date, time, camera names and camera status icons.

Note: To set the system date and time in ―Display‖ menu, refer to section 6.4. To change camera names in the ―Image‖ menu, refer to section 6.5.

See the following chart for camera record status indications:

Icon

Icon Color

Status Description

White

No video signal

Yellow

Video input

Pink

Manual recording

Green

Continuous recording

Blue

Motion detect recording

Red

External alarm recording

See the following chart for alarm status indications:

Icon

Icon Color

Status Description

White

Video signal lost

Yellow

View tampering alarm

Pink

Motion & External alarm

Green

No alarm

Blue

Motion alarm

Red

External alarm

Press the numeric keys to switch to an individual camera in live view. If the DVR has less than 10 channels, press one numeric key to switch to the corresponding channel. For example: Press [2] to view camera #2. If the DVR has 10 or more 10 channels, press two numeric keys to switch to the corresponding channel. For example: Press [0] [2] to select camera #2. Press [1] [2] to

select camera #12.

Press the [EDIT] key to manually sequence live views. You can set auto preview mode in the menu (refer to section 5.2).

Press the [PREV] key to switch multi-screen views.

Press the [Enter] key to pause/resume sequence live view.

4.3 Login

Note: The DVR factory default user name and password is ―admin‖ ―12345‖. ―admin‖ is

the administrator which allows access to all of the DVR functions,it can not be renamed. The administrator can create up to 15 individual users and apply individual privileges to each,.

Press the Menu key and the Login dialog appears.

1. Use the [] / [] keys to select a user.

2. Press the [] key to enter the ―Password‖ edit box. Input the corresponding password. Press [ENTER] to exit edit box. The ―Active Window‖ will move to the ―Confirm‖ button.

3. Press [ENTER] to confirm the entry.

Note: An incorrect user name/password entry will result in an audible alarm. After three incorrect entries the DVR will switch to the live display mode.

4.4 PTZ Control

Note: Ensure that PTZ communication parameters have been configured properly before attempting normal operation. Your password must have PTZ control enabled in order to control cameras.

Note: Please refer to ―PTZ Setup‖ in section 6.14.

Entering the PTZ control interface:

In live mode, press the [PTZ] key. In the login dialog, select a user name and input the correct password. In menu mode, press the [PTZ] key and you will enter the PTZ control interface directly.

There is a ―PTZ Control‖ prompt in the PTZ control interface. The displayed camera name indicates the camera under control. For example, ―Camera 01‖ means you are controlling PTZ camera #1.

Select the desired channel:

In the PTZ control mode, you can press the numeric keys to select the desired channel (Ex: ―0,‖‖1,‖ for camera #1 – or ―1‖ if using a 4/8 channel unit). After you select the camera PTZ, you can use the shortcut keys to control the PTZ.

PTZ Control Options:

Direction control keys: [↑], [↓], [←], [→] ZOOM control keys: [ZOOM+], [ZOOM-] FOCUS control keys: [FOCUS+], [FOCUS-] IRIS control keys: [IRIS+], [IRIS-] Adjust preset keys: [REC/SHOT]; Auto control key: [PLAY/AUTO] Wiper control key: [WIPER/MENU] Light control key: [LIGHT/F1] Auxiliary control key: [AUX/F2]

Calling Preset positions:

In the PTZ control mode, press the [REC/SHOT] key, and then enter the preset number (three numeric keys). The camera will go to the corresponding preset position.

Setting Preset Positions:

To set a camera preset position, move the camera to the desired position. Press and hold the [REC/SHOT] key while entering the preset number.

Note: A preset must be established before you will be able to call the preset in normal operation. Refer to PTZ menu for preset setup. When you exit PTZ control mode, the camera will stay at the current position (depending on the dome used. Some domes may select a return to home position after a predetermined time).

Start/Stop auto PTZ control mode:

In PTZ control mode, press the [PLAY/AUTO] key to start the PTZ auto function. Press the

[PLAY/AUTO] key again to stop.

Note: When PTZ is in auto mode it will stay in auto mode when you exit the PTZ mode. You must enter into PTZ control mode again, and press the [PLAY/AUTO] key to stop.

Exit PTZ control mode:

Press [ESC] or [ENTER] to exit and return to the live view mode.

4.5 Manual Record

Note: In order to perform this function the DVR must have drives installed and formatted

and the user login password must have ―Record‖ enabled.Manual record will lose effective after reboot.

Manual record:

1. In the live view mode, press the [REC] key. In the pop-up login dialog, select a user name and input the correct password to enter into the ―Manual Record‖ interface.

2. In menu mode, press [REC] to enter the ―Manual Record‖ interface directly.

Manual Record Menu:

The Manual Record interface has the following selections: Channel number, channel status, start/stop record, start all and stop all buttons.

1. Channel: Indicates available camera inputs.

2. Status: Indicates one of four settings: means idle. Green means the channel is recording (or set to record including: Continuous recording, alarm recording,

motion detection recording). Red means network transmission. Orange means

both recording and network transmission.

3. Start/Stop: ―‖ means start recording corresponding channel. ―×‖ means stop recording.

4. Start All: Press this button to start all channels recording.

5. Stop All: Press this button to stop all channels from recording.

Note: Manual recording will loss effective after reboot.

Exit manual record:

Press the [ESC] key to enter the live view mode. Press the [MENU] key to enter the main menu. Press the [PLAY] key to enter playback menu. Press the [PTZ] key to enter the PTZ control mode.

4.6 Playback

Note: The user must have ―Playback‖ permission associated with the user name and password in order to enter playback mode.

Playback interface:

In the live view mode, press the [PLAY] key. In the pop-up login dialog, select a username and input the correct password to enter the ―Playback‖ interface.

In the menu mode, press the [PLAY] key to enter into ―Playback‖ interface directly.

Playback Menu:

The Playback interface has the following selections: Chan: Rec. Type, Time selection, Search, Play, Select page, File list box, Backup devices, Copy and Backup Today.

1. Main Channel: Use the [↑] or [↓] key to select one channel.

2. Second Channel: If the DVR supports 2-ch playback, you can use the [↑] or [↓]

keys to select the second channel (other than main channel). These two channels can be played back synchronously. If you select the second channel as none, only the main channel will playback.

3. Rec Type: Use [↑] or [↓] to select recorded files type. The file type options have ―All‖, ―All Time‖, ―Motion Detect‖, ―Alarm‖ and ―Manual‖.

4. Time Selection: You can define the search time section. Move ―Active Frame‖ to

the time edit box, use numeric keys to input the detail time.

5. Search: Search the matched recorded files and display them in the list box. If there is not matched file, a corresponding dialog box will be pop-up.

6. Play by Time: Playback the recorded stream directly based on the time section.

7. Select Page: In the file list box, each page will only display 8 files. If the matched

files are more than 8, you can select page to list other files. 500 pages (4000 files) can be searched in one time. You can use numeric keys or [↑] [↓] keys to select page.

8. File List Box: List the matched files. File started time, file size are displayed in the list box. You can use [↑] [↓] keys to move the scroll bar to select file.

9. Backup Devices: You can select USB flash, USB HDD, USB CD/DVD or SATA CD/DVD to backup the files or clips.

10. Copy: Start to backup.

11. Backup Today: Backup all recorded files of today.

Two playback modes:

1. Search and playback a file: In the playback menu select a channel to search, and a record type. Move the ―Active Window‖ to the ―Search‖ button and press [ENTER]. The DVR will search and list the matched files.

2. Playback by Time: In the playback interface, select a start and an end time using

the time entry boxes and then select the ‖Play‖ button. Video playback will start

from the start time selected.

One channel search

If there are more than eight matched files, use ―Page No.‖ to select additional pages (use numeric keys or [↑] [↓] keys to select a page). In the file list box, use the [↑] [↓] keys to move the scroll bar to the desired file and press [ENTER] to playback the file. If a second channel is selected, these two channels can playback synchronously.

Note: If no file match is found, a message dialog will display indicating that no matching files were found.

One-Channel Play-back

Two-Channel Play-back

There is an information bar at the bottom of the display with the following information: Volume, Play Progress, Play Speed, Played Time and File Total Time. The following front panel playback controls are available:

1. Display/Hide information bar: [MENU]

2. Open/Close sound: [PLAY]

3. Adjust play progress: [←] (Backward), [→] (Forward). The unit is ―%‖.

4. Adjust play speed: Normal speed is ―1x‖. Use [↑] to increase play speed (2X, 4X, 8X and MAX). Use [↓] to decrease play speed (1/2X, 1/4X, 1/8X and Single Frame). When in ―Single‖ pressing [ENTER] moves forward one image (single step).

5. Pause/Continue: Press [ENTER] to pause/continue playback.

6. Copy segment: [EDIT] to start copy, [EDIT] again to end copy.

7. Exit: [ESC]

8. Playback switch: When in 2-ch playback, press [PREV] to switch between main channel and second channel.

Note: When the DVR is performing multiple tasks the actual play speed may not match the speed selected.

Exit playback:

1. From the playback interface, press [ESC] to return to the Live mode.

2. From the playback interface, press [MENU] to enter into main menu.

3. Press [REC] to enter the manual record menu.

4. Press [PTZ] to enter the PTZ control mode.

4.7 Backup Recorded Files

Note: The user must have ―Playback‖ permission associated with the user name and

password in order to enter playback mode and back-up files. Some applications require data to be saved for a long period of time. The required information could range from a short video clip up to the entire database. This section addresses ways to export video from the DVR.

Back up selected files:

1. From the ―live‖ mode, press [PLAY].

2. Enter a valid user name and password to enter the Play Back Menu.

3. Search files as indicated in section 4.6.

4. Select a file in the file list box.

5. Select the ―Save Device‖ (USB flash memory, USB HDD, USB CD/DVD, SATA CD/DVD or SATA HDD).

6. Select ―Copy.‖ A pop-up dialog box will indicate that the file copy is in progress and when the file copy is completed.

Backup intraday recorded files:

1. In the playback interface, select the ―Backup Today‖ button and press [ENTER].

2. All intraday recorded files of all channels will be saved to the device selected. Ensure that the backup device has sufficient space store the data selected. A pop-up dialog will display the backup status.

Note: If backup device is not connected correctly, or the DVR does not detect the backup device, a ―Device Error‖ message dialog will display.

Backup File

Backup video clips:

You can back-up video clips as the file is being played back. The steps are:

1. Search for and select the video you want to export.

2. Play the video and press [EDIT] to start saving the clip.

3. Press [EDIT] again to mark the end of the clip. This clip is ready for export.

4. Repeat the steps above to select additional clips (up to 30 total).

5. Press [ESC] and a message window will display indicating the number of files to be copied.

6. Select ―Confirm‖ and the backup will begin. (―Cancel‖ will abort the process). Press ―Confirm‖ again at the ―File Copied‖ message.

Note: The backup function is effective when two channels are playback synchronously. In such case, each channel can backup 30 segments so 60 segments can be backed up for two channels.

Playback backup video files:

You can playback recorded files in any PC using File Player software. File Player software is available on the CD supplied with the DVR.

4.8 Powering Down the DVR

Note: Turning off the power switch on the rear panel, or pulling the power cord from the

unit is not recommended in order to avoid corrupting data on the disk drives. The safer method is to enter the Menu and turn off the power using the Utilities Menu. Alternately you can press and hold the front panel Power key (or, the IR Remote Power key) for five seconds.

Shutting down the DVR: Using the menu:

1. Enter the ―Utilities‖ menu. (Main, Utilities).

2. Move the ―Active Window‖ to ―Power Off‖ and press【ENTER】.

3. In the power off dialog, press ―Confirm‖ to shut down the DVR.

4. Enter a user name and password as required.

Power off using the [POWER] key on the front panel or IR Remote:

1. In the ―Live‖ mode press and hold the [POWER] key (on the front panel or IR Remote) for more five seconds.

2. A power off dialog will ask you to confirm your selection.

3. Enter a user name and password as required. If an incorrect password is entered three times the unit will return to the live view mode.

Note: A message will display indicating ―Power Off in Process.‖ Do not press any additional keys while the shutdown is taking place.

Abnormal Shutdown:

Warning: Do not power off the unit by switching off the power supply power switch or by pulling the power plug!

Removing the power unexpectedly while the DVR is accessing the disk drives will cause damage to the data and possibly to the drive.

Note: Maintaining constant regulated power to the DVR is essential for normal operation and to preserve the data stored on the disk drives. A UPS (Uninterruptible Power Supply) is recommended for all installations and essential in mission critical applications.

Chapter5 Main and Spot Output

5.1 Main and Spot Output

The DVRs listed below have one main video output and one spot output. The main video output provides access to the DVR menu. The spot output does not. It is intended for normal operation, not system setup. DS-8004HCI-S, DS-8008HCI-S, DS-8016HCI-S series DS-8004HSI-S, DS-8008HSI-S, DS-8016HSI-S series DS-8004HFI-S, DS-8008HFI-S, DS-8016HFI-S series DS-8004HDI-S, DS-8008HDI-S, DS-8016HDI-S series

The spot output is an additional composite monitor used for viewing live video, playback video and for local PTZ control.

Accessing the Main and Spot monitor outputs:

1. Front Panel: Press the [Main/Aux] key to toggle between the ―Main‖ output and the ―Spot‖ output control mode.

2. IR Remote: Press the [VOIP/MON] key to toggle between the ―Main‖ output and the ―Spot‖ output control mode.

Note: Several functions are not available in the ―Spot‖ mode. If you can’t perform a

function, ensure that you are in the ―Main‖ mode.

5.2 Main and Spot Output Live View

The ―Main‖ output is typically used for control of all DVR functions. It provides all the same functionality as the VGA monitor output. The [Main/Aux] key toggles between the ―Main‖ and ―Spot‖ output control modes. Select the ―Main‖ mode and then press the [Menu] key to enter the DVR menu. The main video output will display the following DVR menu:

Enter the ―Preview‖ menu:

Screen Setup Options:

1. Select Out: Use ―Select Out‖ to select the main or Spot outputs:

2. Preview Mode (Live view mode): Use the [↑] [↓] keys to select the desired screen configuration for edit. The menu allows you to select screen formats and insert camera numbers as desired. The number of available formats depends on the number of camera inputs available (1, 4, 9, 12 and 16 displays are available in 16 channel units) See ―Layout‖ below for setup details.

3. Switch Time: This control sets the sequence dwell time in the sequence mode. Each sequencing view will remain on the screen for the amount of time selected. Options include 5, 10, 20, 30 seconds, 1, 2, 5 minutes and never (sequence off). For example: With a 16 channel DVR, if you select ―4 Screen‖ mode and a ―20 Second switch time. The DVR display will change four camera displays every 20 seconds (1-4, 5-8, 9-12, and 13-16).

4. Audio preview: If you enable audio (―‖), when you view a single camera the DVR will play the audio associated with that channel.

5. Layout: The menu provides a window divided into sections. The window sections correspond to the screen format selected (1, 4, 9, 12 and 16). Each individual

section represents one camera. You can move the ―Active Window‖ to each

section. Use the camera selection bar to insert the appropriate camera in the desired cameo. For example: Select the 16 camera mode (16- screen in the mode selection). Move the ―Active Window‖ to one of the segments and press the [Enter] (or [EDIT]) key to enter into the ―Edit‖ mode. Press numeric keys to input a camera for that section of the multi-screen display (‖0‖ ―1‖ for camera #1 on 16 channel units – ―1‖ for camera #1 on units with less than ten channels). The camera number will display in the window. You can arrange the display in any camera order. If you press 0 or 00, the corresponding window will not display live video.

6. Alarm/Aux Out: This configures the monitor that will switch to full screen on alarm.

7. Save the setup selections: Select ―Confirm‖ to save the viewing configuration.

Press ―Cancel‖ or [ESC] to abort.

5.3 Main and Spot Output Playback

Both the ―Main‖ and ―Spot‖ display can be used to playback the recorded files on the DVR HDD. Press the [Main/Aux] key to enter into ―Main‖ or ―Spot‖ control mode, and press the

[PLAY] key to enter into ―Playback‖ menu.

5.4 Main and Spot Output to Control PTZ

Press the Main and the Spot output may be used to perform PTZ control.

1. Press the [Main/Aux] key to select the desired output.

2. Press the [PTZ] key to enter the PTZ control mode.

Note: The [Main/Aux] key is not active while in the PTZ mode. Press the [ESC] key to exit PTZ control mode in order to change monitor control modes.

Chapter6 Advanced Operation Guide

Only users that have ―Parameters Setup‖ permissions assigned to their user name can perform the operations in this section. When the following parameters are modified and saved, you must reboot the DVR before the new parameters take effective. Parameters mentioned earlier do not require a reboot.

 Any network parameters in ―Network‖ menu  Stream type, resolution and record schedule in ―Recording‖ menu  External alarm sensor type in ―Alarms‖ menu  View tampering alarm schedule in ―Image‖ menu  Video loss alarm schedule in ―Image‖ menu  Motion detection alarm schedule in ―Image‖ menu  External alarm schedule in ―Alarms‖ menu  Alarm output schedule in ―Alarms‖ menu  RS232 mode in ―RS232‖ menu  Change video output standard in ―Display‖ menu  Change PTZ parameters in ―PTZ‖ menu

6.1 User Management

The Factory Default user name and password is ―admin‖ ―12345.‖ The user name ―admin‖ can’t be changed. You can change the admin password for security reasons. Move the ―Active Window‖ to ―User‖ and press the [ENTER] key to enter the ―User Management‖ menu.

Note: The system administrator (admin login name) can manage the permissions assigned to individual users. Up to 15 additional users may be selected. When logged on as ―admin‖ you can add users, delete users, modify passwords and select individual permissions for each user.

6.1.1 Add Users

Additional users may be added by those with admin rights:

1. Enter the ―User Management‖ menu (select User from the main menu).

2. In the ―User Management‖ menu, select the ―Add‖ button and press [ENTER].

3. Input the new user name in the pop-up dialog and press [ENTER] (up to 15 users can be added).

Setup the password for the new user:

1. After you add a new user, the password is null (no password). You can skip this

step if you do not want to change the password.

2. Enter the desired password.

3. Verify the entry.

4. Select confirm.

6.1.2 Delete User

1. In the ―User Management‖ interface use the [] [] keys to select a user, then use [] to move the ―Active Window‖ to the ―Del‖ button and press [ENTER].

2. In the pop-up confirmation dialog, press ―Confirm‖ to delete the selected user, or press ―Cancel‖ or [ESC] to abort deleting.

6.1.3 Password Modification

Admin rights are required to change passwords.

1. Enter the User Management menu:

2. Select a user name to edit in the user name list box. Use [][] to select a user,

3. Press [→] to move the ―Active Window‖ to password edit box and press [EDIT] to enter the edit status.

4. Use the numeric keys to input the new password. A password can be up to 16 numbers.

5. Move the ―Active Window‖ to ―Verify password‖ and reenter the password.

6. Select ―Confirm‖ and press [ENTER]. This will activate the new password.

Note: If there is an error in entering or verifying the password an error message box will appear.

In this case, press [ENTER] to return to the password edit box, and reenter the new password and verify again.

6.1.4 User Rights

Setup permissions for new users:

1. In the users list box of the ―User Management‖ menu, use the [] [] keys to select the user name, then use the [] key to move to the ―Set Privileges‖ button and press [ENTER].

Note: Operational rights are divided into ―Local Rights‖ and ―Remote Rights‖. You can assign the necessary rights to the user.

1. Use the [] [] keys to select items and press [ENTER] or [EDIT] to enable or disable the item. ―‖ means the right is assigned to that user.

2. After assignment, press the ―Confirm‖ button to save the settings, or ―Cancel‖ to abort.

User rights description: Local Rights: Local rights are for local operation, such as the operation using front panel,

IR controller and RS-485 keyboard and PTZ control.

1. Record: Manual start/stop recording;

2. Playback: Local playback and backup the recorded files;

3. Parameters Setup: Local setup the DVR parameters;

4. Log: Local view of the DVR log;

5. Utilities: Locally upgrade firmware, format HDD, reboot DVR and shut down DVR, etc.

Remote Rights: Remote rights are similar to local rights, the exception being that you can perform these functions from the remote software. PTZ Control: Remote control PTZ;

1. Record: Remote manual start/stop recording;

2. Playback: Remote playback, download of recorded files from DVR;

3. Parameters Setup: Remote setup the DVR parameters;

4. Log: Remote view of the DVR log;

5. Utilities: Remote upgrade firmware, format HDD, reboot DVR and shut down DVR, etc.

6. Audio: Client talks with DVR;

7. Live view: Network live view;

8. Alarm: Remote control of DVR alarm output;

9. Local Video Out: Remote imitation of front pannel operation;

10. Com Control: DVR RS-232 transparent channel function.

MAC address:

This MAC address is not the address of DVR. It is the MAC address of the PC that will access the DVR. If the MAC address is set to all zeros the user may connect to the DVR from any remote PC. If you setup this MAC address, only the PC with this MAC address can access the DVR using that user name and password.

At PC end, in the DOS prompt, you can use the ―ipconfig‖ command to see the PC MAC address.

6.2 Device ID

The device ID is a unique identifier for the DVR. When you use an IR Remote controller to operate DVR, you must use this device ID to select the DVR. The default device ID is ―88‖. If there is more than one DVR in one place, define a different device ID for each DVR. Otherwise, the IR controller will control all DVRs with the same device ID at the same time.

1. In ―Display‖ menu, select the device ID edit box.

2. Use the numeric keys to input a new device ID. The device ID value is ranged from 01-255.

3. Press the ―Confirm‖ button to save the new ID, or ―Cancel‖ to abort.

6.3 Video Standard and VGA Setup

Video standard: Changing the video format (NTSC/PAL) is easily performed in the

Display menu.

1. Select the ―Display Menu from the Main Menu.

2. Select the ―Video Standard‖ button and select the appropriate standard for your area (NTSC/PAL).

VGA setup:

You can define the VGA resolution and refresh frequency in the ―Display‖ menu. Options include: 1024*768/60Hz, 800*600/60Hz and 800*600/75Hz.

1. Select the Display Menu.

2. Use the [] [] keys to select the desired format.

3. Press ―Confirm‖ to save, or ―Cancel‖ to abort.

6.4 Date and Time Setup

Setting the Date/Time:

1. Enter Display section.

2. Enter the date and the time in the appropriate boxes below DST Setup.

3. Enter section Setup next to DST.

4. Enable or disable the DST (Daylight Savings Time) option. If you enable DST you must enter the change dates for your time zone.

5. Select ―Confirm‖ to return to the previous menu.

Selecting the Date/Time Display Settings: You can modify the Time/Date display properties for each camera, including display status, position and format. You can copy the properties of one camera to all cameras. These modifications are made in the ―Image‖ Menu.

Selecting Camera Date/Time display settings:

1. Enter the ―Image‖ Menu and select a camera to modify.

2. Select the ―Date OSD.‖ Options include: Opaque&Steady, Transparent&Steady, Transparent&Flashing, Opaque&Flashing,

3. Select the ―Position button next to the OSD setup. A display window will show the position of the Time/Date display.

4. Display position and format: The image consists of a 22x15 grid NTSC

(22x18 PAL). Use the [] [] [] [] keys to move the OSD position.

5. Press the [EDIT] key to select OSD time/date format. Options include:

 MM-DD-YYYY day in week hh:mm:ss (default)

 MM-DD-YYYY hh:mm:ss  DD-MM-YYYY day in week hh:mm:ss  DD-MM-YYYY hh:mm:ss  YYYY-MM-DD day in week hh:mm:ss  YYYY-MM-DD hh:mm:ss

YYYY = year, MM = month, DD = day, hh = hours, mm = minutes and ss = seconds.

6. Press [ENTER] to save and return to the ―Image‖ menu or press [ESC] to abort.

6.4.1 Daylight Saving Time Setup

In the ―Display‖ menu press the DST ―Setup‖ button to enter the DST setup interface.

DST means Daylight Saving Time. Select the check box to enable the function, and enter the DST start time and end time for you local area.

6.5 Image Setup

6.5.1 Camera Name Setup

Camera Name: You can modify camera names in the ―Camera Input Adjustment‖

Menu.

Note: Camera names can’t be copied to other cameras.

1. From the ―Main Menu,‖ select the ―Image‖ menu.

2. Select a camera to configure.

3. Select the ―Name‖ entry to modify the camera name. Move the ―Active Window‖ to the camera name edit box and press [EDIT] to enter the edit mode. You can input numbers, uppercase and lowercase characters (refer to Chapter 3.4). The camera name can be up to 32 characters.

4. Press [ENTER] to exit the edit mode.

5. Select ―Confirm‖ and press [ENTER] to save the modification, or Press ―Cancel‖ or [ESC] to abort.

Position the name on the display:

1. If you do not want to display the camera name, disable the check box beside

camera name edit box. The disable flag is ―×‖. If you enable the check box, you

can setup the camera name position. You can copy the position to any other camera. The setup steps are:

2. Enable the check box on the right side of camera name, then move the ―Active Window‖ to the ―Position‖ button and press [ENTER] to enter the camera name position setup interface.

3. Use the [] [] [] [] keys to move camera name position. Press [ENTER] to

return the ―Image Setup‖ menu. Press ―Confirm‖ to save the settings, or ―Cancel‖

or [ESC] to abort.

6.5.2 Video Parameter Setup

This feature allows you to make changes to the visual display of individual cameras. You can adjust the brightness, saturation, contrast and hue. You can setup the camera individually and you can copy the video parameters of one camera to any other cameras. Here are the setup steps:

1. Enter the ―Camera Input Adjustment‖ menu and select camera (use the [] [] keys to select a camera).

2. Select the ―Adjust‖ button for each parameter; Brightness, Contrast, Saturation and Hue. Press the [ENTER] key to access the parameter overlaid on an image of the selected camera. Use the [] [] keys to adjust as you watch the image change. When you are satisfied with the results, press [ENTER] to return ―Image Setup‖ menu.

4. Repeat the steps above to adjust any other cameras.

5. Press ―Confirm‖ to save the settings, or ―Cancel‖ or [ESC] to abort.

6.6 Mask Area Setup (Privacy Mask)

Some cameras may be installed in a sensitive area where it would be advantageous to mask a portion of the image to prevent viewing and recording. A Privacy Mask can be applied to any camera. This area will be blacked out on the viewed and recorded image.

Setup of a Privacy Mask:

1. Enter the ―Camera Input Adjustment‖ menu:

2. Select a camera: Use the [] [] keys to select a camera.

4. Enable the check box next to the ―Area‖ button (press the Edit key to enable ―‖).

5. Select the ―Area‖ button and press [ENTER] to enter the mask area setup.

Setup mask area: In the mask area setup interface, there is one small yellow pane on the upper left side. For NTSC cameras, the screen is divided into 22*15 sections (22*18 for PAL). Use the [] [] [] [] keys to move the yellow pane to a starting position and press the [EDIT] key. The yellow pane will turn red. Use the [] [] [] [] keys to extend the red privacy mask area.

 Note: Press the [A] key to clear all mask areas.  The maximum mask area size is 8*8 panes. Up to four mask areas are allowed on

each camera.

 Once you have the area(s) defined, press [EDIT] to accept, or [ESC] to cancel.

Saving the masked area:

 In ―Camera Input Adjustment‖ menu, press the ―Confirm‖ button to save the mask

area, or press ―Cancel‖ to abort.

 You can repeat steps listed above to setup mask areas for other cameras.

Example of mask area function (blacked out area over the camera image).

6.7 View Tampering Alarm

With this function enabled, an alarm will be produced when the camera view is blocked.

1. Enter the ―Camera Input Adjustment‖ menu.

2. Select a camera: Use [] [] keys to select a camera.

3. Reach the list dialog box next to ―View Tampering‖.

4. Sensitivity Selection: Use the [] [] keys to select the sensitivity level. The

sensitivity options are: Low, Normal and High. Selecting one of them will active the ―Area Setup‖ and ―Policy Setup‖ functions.

5. View tampering area setup: Move the ―Active Window‖ to the ―Area‖ button and press [ENTER] to enter the area setup interface. The setup methods are the same as those used for the mask area setup.

6. After setting up the area, press [ENTER] to return to the ―Image Setup‖ menu, or [ESC] to abort.

Note: Only one view tampering area can be setup per camera.

7. Alarm schedule setup: When there is a view tampering alarm present, the DVR

will handle the alarm based on the schedule selected. You can set 4 periods for each day of the week. You can copy the schedule of one day to other days.

Note: Time periods may not overlap. You must reboot the DVR before the settings take effect.

8. Setup alarm policy: If a view tampering alarm occurs while the schedule is active

the DVR will respond based on the policy Selected. You can select one or more of the following: ―On Screen Warning‖, ―Audible tone‖, ―Upload to Center‖, ―Trigger Alarm

Output‖ and ―Send E-mail‖. Use the [] [] and [EDIT] key to enable or disable selections. ―×‖ is disable and ―‖ is enable.

9. Save alarm setup: After selecting the setup parameters, press ―Confirm‖ to

return ―Camera Input Adjustment ‖ menu. In the ―Camera Input Adjustment‖ menu press ―Confirm‖ to save the setup and return to the main menu, or ―Cancel‖ or [Esc] to

abort.

10. Save all cameras: If you want to setup additional cameras, repeat steps two

through eight. In ―Image Setup‖ menu, press ―Confirm‖ to save all cameras parameters. Press ―Cancel‖ key or [ESC] key to abort.

6.8 Video Loss Alarm

This feature provides an alarm when camera input video is lost.

1. Enter the ―Camera Input Adjustment‖ menu:

2. Select camera: Use [] [] keys to select a camera.

3. select the ―Handle‖ option next to ―Signal Loss.‖

4. Setup alarm schedule: Enter ―Policy‖ to setup alarm schedule.A vid-loss alarm will be generated only during the scheduled times selected.

Note: The 4 time periods can be selected per day. The timeframes may not overlap. Note: the DVR must be rebooted before the settings take effect.

5. Setup alarm policy: You can select one or more response: ―On Screen Warning‖, ―Audible tone‖, ―Upload to Center‖ and ―Trigger Alarm Output‖. Use the [] [] and

[EDIT] key to enable or disable items. ―×‖ is disable and ―‖ is enable.

6. Save alarm setup: After making selections, press ―Confirm‖ to return to the ―Camera Input adjustment‖ menu. In this menu, press ―Confirm‖ to save current Camera parameters and return main menu.

7. Save all cameras: If you want to setup other cameras, please repeat steps two through six. In ―Image Setup‖ menu, press ―Confirm‖ to save all cameras parameters, or [ESC] to abort.

6.9 Motion Detection Alarm

This feature generates an alarm when video motion is detected in a camera views.

Setting Up Motion Detection:

1. Enter the ―Camera Input Adjustment‖ menu:

2. Select camera: Use [] [] to select one camera.

3. Select motion detection sensitivity: There is a selection button to the right of

―Motion Det. Level‖ that selects the motion detection sensitivity. There are 7 options from 0 (the lowest) to 5 (the highest) and ―Off‖. Use the [] [] keys to

make a selection. In the ―Off‖ option the DVR will not response to motion detection. If you select other options the ―Motion Area Setup‖ and ―Policy Setup‖ buttons will

be active. If you select low sensitivity, such as 0, a great deal of image movement is required to generate a motion alarm. A high sensitivity setting (like 5) will respond to smaller motions within images. The default sensitivity is 2. You may have to test different sensitivity levels in order to find the appropriate settings for some cameras.

4. Motion area setup: You must define motion areas so that DVR will response

when there is motion in those areas. Move the ―Active Window‖ to the ―Area‖

button on the right side of sensitivity selection box and press [ENTER] to enter the ―Motion Area Setup‖ interface.

The screen is divided into 22*15 panes (22*15 PAL). There is one yellow panel on the upper left side. The motion area setup steps are the same as that of mask area setup (refer to chapter 6.6). The only differences are that you can use the [PTZ] key to set the whole screen as a motion area. Multi motion areas can be defined.

5. Setup multi areas: After you setup one motion area, press the [EDIT] key.

The yellow pane will appear again allowing another motion box selection.

6. Clear part of motion area: Move the yellow pane near the start position of the area you want to clear. Press [EDIT] and the yellow pane will turn black. Use the

[↓] [→] keys to enlarge or shrink the black area. Press the [EDIT] key to clear this part motion area.

7. Press [Enter] to save the changes, or [ESC] to cancel.

Note: Press [A] key to clear all motion areas.

The keys used to setup motion areas are as follows:

 [↑] [↓] [←] [→]: Move yellow pane to any position.  [EDIT]: Yellow - panel (position) changes to red (adjust panel size).  [→]: Right enlarge red pane;  [←]: Left shrink red pane;  [↓]: Down enlarge red pane;  [↑]: Up shrink red pane;  [PTZ]: Set whole screen as motion area;  [A]: Clear all motion areas;  [ENTER]: Save and return to ―Image Setup‖ menu;  [ESC]: Cancel setup and return to ―Image Setup‖ menu;

Motion Alarm Policy: This feature allows you to configure multiple alarm responses based on a single alarm input.

1. In the ―Camera Input Adjustment‖ menu, move the ―Active Window‖ to the ―Policy‖ button to the far right of ―Motion Det. Level‖ and press [ENTER] to access the

―Motion Alarm Handle‖ menu:

2. Motion alarm record channel setup: Once a motion alarm has been detected that information can be used to trigger other alarm conditions. In the ―Motion

Alarm Handle‖ menu you can select one or more channels to record based on a

camera motion alarm input. Use the [ENTER] or [EDIT] key to enable the flag (―‖).

Note: To enable the linked recording function the affected channels must be enabled in

the ―Recording‖ menu. The schedule must be in an enabled time period (if selected) and the ―Rec Type‖ must be set to either ―Motion Detection, or Motion/Alarm.

3. Motion alarm schedule: The motion schedule determines the time periods during which motion alarms will be recognized by the DVR. Motion alarm

responses include: ―On Screen Warning,‖ ―Audible tone,‖ ―Upload to Center‖ and ―Trigger Alarm Output‖. You can setup 4 time periods for one day of the week.

Note: Time periods may not overlap.

4. Motion alarm handling setup: You can select one or more response methods

such as ―On Screen Warning‖, ―Audible Warning‖, ―Upload to Center‖,―Trigger Alarm Output‖ and ―Send E-mail‖.

Description: If ―On Screen Warning‖ is enabled, and a motion alarm occurs while the DVR

is in live mode, the alarmed camera will display on the monitor. If more than one alarm is present, the alarmed cameras will sequence at a ten second rate. When the motion alarms clear, the display returns to the previous viewing mode.

5. Save motion alarm setup: Press ―Confirm‖ to return to the ―Image Setup‖ menu.

In the ―Image Setup‖ menu, press ―Confirm‖ to save the current camera

parameters.

6. Save all cameras: You can repeat steps tow through eight to setup motion detection parameters for other cameras. Also you can copy the parameters of one camera to any other cameras.

Note: The Motion alarm area may not be copied to other cameras.

If you want to disable the motion alarm area and motion alarm policy, select motion alarm sensitivity as ―Off‖.

6.10 Live View Setup

The ―Preview‖ menu provides access to live view parameters.

In ―Preview‖ (live) menu, you can setup live mode, screen sequence time, enable or

disable audio and live view screen formats. Please refer to section 5.2 for details.

6.11 Recording Setup

Select ―Recording‖ from the main menu.

Recording Menu Functions:

 If HD Full: There are two options: ―Overwrite‖ and ―Stop recording‖. If you select

the ―Overwrite‖ option, when all HDDs in DVR are full, the DVR will overwrite the

earliest recorded files and continue recording. If you select the ―Stop recording‖

option, when all drives are all full, the DVR will handle it as ―Hard Disk Full‖ exception providing alarm outputs as selected (please refer to chapter 6.16 for the exception menu).

 SATA1 Disk: For –S series DVR, 1st SATA interface can be extended as External

SATA. You can connect an E-SATA device (such as disk array or HDD) for either recording or backup. In the menu, please select 1st SATA disk usage.

 Select Camera: Use the [↑] [↓] keys to select a camera.  Record Para: There are two options,‖Normal‖ or ―Event‖.Event recording includes

such as Alarm recording and Motion detection recording.You can setup normal recording and event recording separately here.

 Stream Type: There are two options, one is ―Audio&Video‖ stream and the other

is ―Video‖ stream only. If you want to record video and audio, select ―Audio&Video‖

option, otherwise you can select the ―Video‖ option to record video Only.

Note: If you change this option, the DVR must reboot before the changes take effect.

 Resolution: Higher resolution provides a clearer image. The resolution options

from low to high are: QCIF, CIF, 2CIF, DCIF, 4CIF.

Note: Different DVR may support the different resolution level,some supports up to 4CIF and some may only support up to CIF.Please find the real resolutions under this list box of a particular DVR. If you change resolution options the DVR must reboot before the changes take effect.

 Bit Rate: You can select different bit rates to accommodate different settings of

resolution and frame-rate options include: (bps): 32K, 48K, 64K, 80K, 96K, 128K, 160K, 192K, 224K, 256K, 320K, 384K, 448K, 512K, 640K, 768K, 896K, 1M,

1.25M, 1.5M, 1.75M, 2M and ―User define‖.

The appropriate max bit rate selection is related to the resolution selected. If you select a high resolution, you must select high bit rate. For CIF resolution, the typical max bit rate is 384K~768Kbps for real time compression. For 2CIF/DCIF resolution, the typical bit rate is 512K~1Mbps real time compression. For 4CIF resolution, the typical bit rate is 1.25Mbps~1.75Mbps for real time compression. Of course, you will select the proper bit rate based on the camera, background and image quality requirement.

 Frame Rate: Frame per second. Options are: Full (NTSC is 30 FPS and PAL is

25FPS), 20, 16, 12, 10, 8, 6, 4, 2, 1, 1/2, 1/4, 1/8, 1/16. For lower frame rates you can select low bit rates to save bandwidth.

Note: Some series DVR may have lower frame rate for a particular resolution.

 PreRecord Time: This sets the buffer size for retaining video/audio When you

enable motion detection recording or external alarm recording. You can define a prerecord time. The options are: No Prerecord, 5 Seconds (default selection), 10 Seconds, 15 Seconds, 20 Seconds, 25 Seconds, 30 Seconds and Max Prerecord. MaxPreRecord is to save all data in Prerecord buffer. The Prerecord time is related to the bit rate (the lower the bit rate, the longer the Prerecord time).

 If the bit rate (Max bit rate) is very low, and you select the ―Prerecord Time‖ as ―5

Seconds‖ the actual prerecord time is more than 5 seconds. On the other side, if the bit rate is high, and the ―Prerecord Time‖ is set to ―30 Seconds,‖ the actual

prerecord time may be less than 30 Seconds.

 PostRecord Time: This sets the length of time the DVR will continue to record in

alarm record mode after the alarm clears. When external alarm or motion alarm ends the DVR will continue recording for a selected period of time. The options are: 5 Seconds (default), 10 Seconds, 30 Seconds, 1 Minute, 2 Minutes, 5 Minutes and 10 Minutes.

 Enable EventPara: This setting activates Event recording parameters. ―×‖ means

disable and ―‖ means enable.

 Enable Rec: This setting determines whether the camera will record. Recording

may be halted based on additional schedule settings.

 Schedule: When you enable recording function, you can setup recording

schedule.

Note: When the camera’s recording schedule is modified, you must reboot the DVR before the changes will take effect.

All day Recording Setup:

1. Enable ―Enable Rec‖ and enter the recording ―Schedule‖ menu.

2. In the recording menu, use [ENTER] or [EDIT] to enable the record function (―‖ flag). Select the ―Schedule‖ button to enter the recording schedule menu.

3. Select a day and enable all day recording: Day selection options: Monday, Tuesday, Wednesday, Thursday, Friday, Saturday and Sunday. Use the [↑] [↓] key

to select a day. Move the ―Active Window‖ to the ―All Day‖ selection box and press

[ENTER] or [EDIT] to enable the ―All Day‖ option. ―×‖ means disable and ―‖ means enable.

4. Select the Record type: The ―Rec Type‖ options are: All Time, Motion Detect, Alarm, Motion|Alarm, and Motion&Alarm. For the ―All Day‖ record mode, only one record type can be selected.

5. Copy to: You can copy the current day to other days.

6. Save: Press ―Confirm‖ to return to the ―Recording‖ menu. Press ―Confirm‖ again to save the parameters and return main menu.

Scheduled Recording Setup:

1. Enter the recording schedule menu:

2. In recording menu, use [ENTER] or [EDIT] to enable record function (―‖ flag), press the ―Schedule‖ button to enter the recording schedule menu.

3. Select a day and disable all day recording option: For ―Day‖ item, there are

options: Monday, Tuesday, Wednesday, Thursday, Friday, Saturday and Sunday. Navigate to the ―All Day‖ check box and ensure that it is deselected ([ENTER] or [EDIT] until an ―×‖ appears in the box). .

4. Setup time period and record type: You may select up to four time periods for

each day and each time period can select a different record type. Input the start time and the stop time for each time period and select the record type for each time period. The record type options are: All Time, Motion Detect, Alarm, Motion&Alarm and Motion|Alarm.

Note: The time periods may not overlap.

5. Copy to other days: You can repeat steps two and three to setup other days

You can copy the current day to other days.

6. Save: Press ―Confirm‖ to return to the ―Recording‖ menu. Press ―Confirm‖ again

to save the parameters and return to the main menu.

Note:

1) If the selected record type is ―Motion Detect‖ or other related types, you must setup ―Motion Detection‖ in order to trigger motion recording (refer to chapter 6.9).

2) If the selected record type is ―Alarm‖ or other related types, you must setup ―Alarms‖ in order to trigger alarm recording (refer to chapter 6.12).

3) The time period range is from 00:00—24:00.

6.12 Alarm I/O Setup

Configuring Input Alarms:

1. In main menu select ―Alarms‖ to enter the alarm setup menu.

2. Select an alarm input using the [↑] [↓] keys.

3. Alarm type: This is sensor type used. You can select ―Normal Open‖ or ―Normal Closed‖ to accommodate the sensor type used.

4. Enter the “Alarm Handling” sub menu: In the ―Alarms‖ menu, there are two

options for ―Alarm Handling.‖ One is ―Ignore‖, and the other is ―Handle‖. If you

select the ―Handle‖ option the ―Policy‖ and ―PTZ Linkage‖ buttons will activate. Select the ―Policy‖ button and press [ENTER] to access the ―Alarm in Handling‖

sub menu:

5. Alarm trigger record channel setup: You can select channels to record for each alarm input. In the sub menu, you can use [ENTER] or [EDIT] to enable the record

channel. ―×‖ means disable and ― means enable.

Note: In order to trigger the channel to record, the channel must be enabled in the ―Recording‖ menu. Refer to chapter 6.11 for details.

6. Schedule for alarm handle method: When a schedule is enabled, external alarms will trigger a DVR response only during the scheduled on times.

7. Alarm handle method (alarm response): Alarm responses include: ―On Screen Warning‖, ―Audible Warning‖, ―Upload to Center‖, ―Trigger Alarm Output‖ and ―Send

Email‖.

Note: If ―On Screen Warning‖ is enabled, an external alarm while viewing in the live mode will cause the alarmed camera to display on the monitor. Multiple alarms will sequence on the screen. When the external alarm clears the display will return to the previous viewing screen.

8. Save setup: In ―Alarm in Handling‖ sub menu, press the ―Confirm‖ button to return to the ―Alarms‖ menu. In ―Alarms‖ menu, press ―Confirm‖ button to save the

parameters.

PTZ Linkage:

1. Select the ―PTZ Linkage‖ button to access the ―PTZ Linkage‖ setup menu:

2. Select a camera and then select one of following PTZ linkage options:

 Preset: Set the flag as ―‖ to enable preset and enter the preset number in the

presser selection box. Please refer to chapter 6.14 for preset setup.

 Sequence: Set the flag as ―‖ to enable sequence and input the sequence

number. Please refer to chapter 6.14 for sequence setup.

 Cruise (Pattern): Set the flag as ―‖ to enable cruise (pattern). Please refer to

chapter 6.14 for cruise (pattern) setup.

3. Press the ―Confirm‖ button to save and return to the ―Alarms‖ menu. Press ―Cancel‖ to abort and return ―Alarms‖ menu.

Note: Please make sure that the PTZ you are using can support preset, sequence and cruise (pattern) functions. Also make sure that you configure them in the PTZ menu. One external alarm input can trigger multiple PTZ links.

4. Copy the parameters: You can copy the parameters of current alarm input to other external input.

5. Save setup: In ―Alarms‖ menu, press ―Confirm‖ button to save the parameters. Press ―Cancel‖ button or [ESC] to abort.

Alarm relay output setup:

1. In the ―Alarms‖ menu, use the [↑] [↓] keys to select an alarm output.

2. Select delay time: This feature selects the amount of time the alarm triggers remain after the alarm clears. The post alarm option times are: 5 Seconds, 10 Seconds, 30 Seconds, 1 Minute, 2 Minutes, 5 Minutes, 10 Minutes and Manual

Stop. If you select the ―Manual’ option, the alarm output will not stop until you

select the ―Clear Alarm‖ button in ―Utilities‖ menu. So the actual alarm output time

is made up of alarm input time and this delay time.

3. Enter the alarm out schedule: You can schedule the times of day that the alarm

outputs are active. Move ―Active Frame‖ to ―Schedule‖ button on right side of ―Alarm Out Time‖ item, press [ENTER] to access the corresponding schedule

menu:

4. Setup alarm out schedule: Like other schedule setup, you can set 4 time periods

for one day and 7 days for one week. When you finish setup, press the ―Confirm‖ button to return ―Alarms‖ menu.

5. Copy one alarm output parameters to other alarm output: In the ―Alarms‖ menu, you can copy parameters of current alarm output to other alarm output.

6. Save setup: When you finish setup, in ―Alarms‖ menu, press the ―Confirm‖ button to save.

Note: If any schedule is modified, you must reboot the DVR before it takes effect.

100

6.13 Network Setup

This section describes network parameters for communication with remote software.

Note: If any network parameter is modified, you must save and reboot the DVR before changes will take effect.

In main menu select the Network option to access network setup.

6.13.1 Network Settings

 NIC Type:Default is ―10M/100M Auto.‖ Other options are: 10M Half-Dup, 10M

Full-Dup, 100M Half-Dup and 100M Full-Dup.

 IP address: The IP address must not be conflict with other IP addresses on the

network. If there is DHCP server in the network, you can set the IP as ―0.0.0.0‖,

save and reboot DVR. In reboot process, DVR will search the DHCP server and be assigned a dynamic IP address. The dynamic IP address will display in the menu. You will need to enter a static IP address if there is no DHCP service available. If the DVR uses the PPPoE function, also DVR can dialup into internet and this information will display in the menu.

 Port: Network access port number, must be greater than 2000.  Advanced:

Securitytec DS-8016HCI-S, DS-8016HDI-S, DS-8004HDI-S, DS-8008HDI-S, DS-8004HDI-SL User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual