Security Command XR20, XR40, Command Processor XR20 User Manual

User’s Guide

XR20

Copyright © 1996, 1997 Digital Monitoring Products, Inc.

Information furnished by DMP is believed to be accurate and reliable.

This information is subject to change without notice.

The XR20 panel is UL listed for Grade A Household Service as well as Commercial Burglary Service.

Silencing an Alarm
All/Perimeter and Home/Away Systems

1. While the alarm bell or siren is sounding, enter your user code. The keypad displays DISARM SILENCE.

2. Press the SELECT key under SILENCE to stop the bell or siren. This does NOT disarm the system.

3. If your system is programmed to send an Abort (alarm cancel) report to the central station, the keypad displays ALARM CANCELLED.

Area Systems

1. While the alarm bell or siren is sounding, enter your user code. The system silences the alarm bell or siren.

2. If your system is programmed to send an Abort (alarm cancel) report to the central station, the keypad displays ALARM CANCELLED.

Silencing an Alarm
All/Perimeter and Home/Away Systems

1. While the alarm bell or siren is sounding, enter your user code. The keypad displays DISARM SILENCE.

2. Press the SELECT key under SILENCE to stop the bell or siren. This does NOT disarm the system.

3. If your system is programmed to send an Abort (alarm cancel) report to the central station, the keypad displays ALARM CANCELLED.

Area Systems

1. While the alarm bell or siren is sounding, enter your user code. The system silences the alarm bell or siren.

2. If your system is programmed to send an Abort (alarm cancel) report to the central station, the keypad displays ALARM CANCELLED.

Security Command User's Guide

for XR20 Command Processor Panels

Table of Contents

Security Command User's Guide

for XR20 Command Processor Panels

Table of Contents

i

About your system

Emergency Evacuation Plans .......................................ii

About Your Security System..........................................1

The Security Command Keypad ...................................2

Special Security Command Messages .........................3

Special Security Command Tones ................................3

Understanding Security System Terms .........................4

Sensor Reset ...............................................................13

Outputs On Off ............................................................14

Bypass Zones ..............................................................14

Zone Monitor ................................................................15

System Test..................................................................16

User Codes ..................................................................16

Ambush Codes.............................................................18

About your system

Emergency Evacuation Plans .......................................ii

About Your Security System..........................................1

The Security Command Keypad ...................................2

Special Security Command Messages .........................3

Special Security Command Tones ................................3

Understanding Security System Terms .........................4

How your System Operates ..........................................6

Arming and disarming

Area System Arming .....................................................7

Area System Disarming ................................................8

All/Perimeter System Arming ........................................9

All/Perimeter System Disarming ..................................10

Home/Away System Arming.........................................11

Home/Away System Disarming....................................12

User Menu Functions

Security Command User Menu ....................................13

User Checkin................................................................13

Sensor Reset ...............................................................13

Outputs On Off ............................................................14

Bypass Zones ..............................................................14

Zone Monitor ................................................................15

System Test..................................................................16

User Codes ..................................................................16

Ambush Codes.............................................................18

Schedules ....................................................................19

Date and Time..............................................................20

Display Events .............................................................21

How Your System is Setup

System Setup...............................................................24

User Codes Record Sheet ...........................................25

Optional Features

Easy Entry™ User's Guide ..........................................27

Pager Direct™ User's Guide........................................29

Phone Access™ User's Guide.....................................31

FA113 Wireless Remote User's Guide.........................33

Index ............................................................................34

Emergency Evacuation Plans

The National Fire Protection Association recommends that you
establish an emergency evacuation plan to safeguard lives in the
event of a fire or other emergency. Use the following steps as a guide.

Draw a floorplan of your home or business

On a clean sheet of paper, draw the walls, windows, doors, and
stairs. Also draw any obstacles that a person may encounter while
exiting the building such as large furniture or appliances.

Develop escape routes

Determine at least two routes the occupants in each room can take
to safely escape. One route can be the most obvious such as the
door. Another can be through a window that can be easily opened.
If the window is high off the ground, an escape ladder should be
provided.

Draw arrows on the floorplan to show escape routes from each room.

Decide where to meet

Prearrange a meeting place outside and away from where emergency
personnel are likely to be working. A neighbor's house or across the
street in the front of the house are good locations. Always perform a
head count to make sure all occupants safely exited. NEVER ENTER
A BURNING BUILDING. If the head count shows one or more
persons missing, give this information immediately to the authorities.
Never enter a building to look for someone.

Practice your escape plans

Devising an escape plan is only the beginning, before the plan can
be effective everyone should practice the escape routes from each
room.

Building Front

Building Back

First Floor Second Floor

Fire Escape

Window Ladder

Early detection

The best way to survive a fire or other emergency is to get out early.
The installation of a fire alarm system, with smoke and carbon
monoxide detectors in each room, can greatly decrease your risk of
loss or injury.

Emergency Evacuation Plans

The National Fire Protection Association recommends that you
establish an emergency evacuation plan to safeguard lives in the
event of a fire or other emergency. Use the following steps as a guide.

Draw a floorplan of your home or business

On a clean sheet of paper, draw the walls, windows, doors, and
stairs. Also draw any obstacles that a person may encounter while
exiting the building such as large furniture or appliances.

Develop escape routes

Determine at least two routes the occupants in each room can take
to safely escape. One route can be the most obvious such as the
door. Another can be through a window that can be easily opened.
If the window is high off the ground, an escape ladder should be
provided.

Building Front

Building Back

First Floor Second Floor

Fire Escape

Window Ladder

ii

1

About Your Security System

Your Security Command system has been designed with your
safety and comfort in mind. It uses the latest in computer technology
to create the most user friendly security and fire system on the
market today.

The system combines ease of use with a simple to understand
Security Command keypad display to offer the full range of features
requested by today’s security system owners. Security Command
can protect both the interior and perimeter of your home or business
while you're away or just the perimeter when you're inside giving you
a wall of security and peace of mind.

You can turn portions of your protection on or off at any time by
pressing a few buttons. You can add, delete, and change personal
security codes at any time or check the status of all protection
devices in the system.

Parts of the System

There are two main parts to the Security Command system, the
Security Command keypad and the keypad User Menu.

Security Command keypad

This is the device we've placed at certain locations throughout the
premises that allow you to turn the system’s protection on and off
using your personal security code number.

Keypad User Menu

The keypad also supplies a User Menu containing all of the functions
you need to fully operate your system. For example, to change a
personal security code number.

A Note About False Alarms

One of the most important concerns facing the security industry
today is false alarms. The accidental dispatching of police and fire
agencies places others in jeopardy by limiting the response capability
of those emergency service units.

As part of our commitment to reducing false alarms, we’d like to
encourage you to read this guide thoroughly. All the information
contained here can help you quickly, and comfortably, learn the
operation of the Security Command system. If you have any
additional questions, or feel that you need more training, please
don’t hesitate to contact us.

Test Your System Weekly

It is recommended that you test the burglary portion of your system
at least once each week. Testing should involve an active test of all
doors, windows, and motion detectors connected to your system. If
your system also has fire protection, call the service department to
find out how this portion of your system should be tested.

Refer to the System Test section of this guide for instructions on
testing the burglary portion of your system.

Introduction

Introduction

About Your Security System

Your Security Command system has been designed with your
safety and comfort in mind. It uses the latest in computer technology
to create the most user friendly security and fire system on the
market today.

The system combines ease of use with a simple to understand
Security Command keypad display to offer the full range of features
requested by today’s security system owners. Security Command
can protect both the interior and perimeter of your home or business
while you're away or just the perimeter when you're inside giving you
a wall of security and peace of mind.

You can turn portions of your protection on or off at any time by

A Note About False Alarms

One of the most important concerns facing the security industry
today is false alarms. The accidental dispatching of police and fire
agencies places others in jeopardy by limiting the response capability
of those emergency service units.

As part of our commitment to reducing false alarms, we’d like to
encourage you to read this guide thoroughly. All the information
contained here can help you quickly, and comfortably, learn the
operation of the Security Command system. If you have any
additional questions, or feel that you need more training, please
don’t hesitate to contact us.

Test Your System Weekly

Introduction

2

A BC

D E F

G H I JK L

VW XMNO P Q R STU

YZ

COMMAND

90

1234
5678

POWER

JONES RESIDENCE
FR I 2: 51 AM

Introduction

Data Entry keys

These keys allow you to enter your user code when arming or
disarming or enter other information into the system.

The ARROW key

The ARROW key is used to go back through the keypad displays
while operating your system. You can press the ARROW key to back
up through the list of functions in the User Menu or to make a
correction by erasing the last character you entered.

The COMMAND key

The COMMAND key allows you to advance through the keypad
displays or User Menu or complete a data entry function.

AC LED

This LED remains on steady as long as your system is connected to
its AC power supply. Should there be an interruption, the LED turns
off and the system's backup battery maintains normal operation for
a time allowing you to contact our service department.

32-Character Keypad User Options Menu

Press and hold the ARROW and COMMAND keys for about two
seconds. The keypad display shows SET BRIGHTNESS. Use the
left SELECT key to lower the display brightness. Use the right
SELECT key to increase the display brightness. Press COMMAND.

At SET TONE, use the left SELECT key to lower the keypad tone.
Use the right SELECT key to raise the keypad tone. Press COMMAND.

At SET VOLUME LEVEL , use the left SELECT key to lower the
keypad volume. Use the right SELECT key to raise the keypad
volume. Press the ARROW key to exit out of the User Options menu.

AC

LED

Lighted display
SELECT keys
Data Entry keys
COMMAND key
ARROW key

Lighted display
SELECT keys
AC LED
Data Entry keys
COMMAND key
ARROW key

The Security Command Keypad

Your system may have one or more easy to use Security Command
keypads (16 or 32 character) that allow you to properly operate the
system. The illustration and descriptions below highlight some of the
keypad features:

The SELECT keys

There are four keys under the display called the SELECT keys.
These keys are one of the features that make your system so easy
to operate. They allow you to choose what to do by pressing the
SELECT key under choices being shown in the display.

1234

567

8

90

COMMAND

A B C

DEF

GHI JKL

VWX

STUPQRMNO

YZ

POWER

32-Character Keypad

16-Character Keypad

A BC

D E F

G H I JK L

VW XMNO P Q R STU

YZ

COMMAND

90

1234
5678

POWER

JONES RESIDENCE
FR I 2: 51 AM

Data Entry keys

These keys allow you to enter your user code when arming or
disarming or enter other information into the system.

The ARROW key

The ARROW key is used to go back through the keypad displays
while operating your system. You can press the ARROW key to back
up through the list of functions in the User Menu or to make a
correction by erasing the last character you entered.

The COMMAND key

The COMMAND key allows you to advance through the keypad
displays or User Menu or complete a data entry function.

AC LED

This LED remains on steady as long as your system is connected to
its AC power supply. Should there be an interruption, the LED turns

AC

LED

Lighted display
SELECT keys
Data Entry keys
COMMAND key
ARROW key

The Security Command Keypad

Your system may have one or more easy to use Security Command
keypads (16 or 32 character) that allow you to properly operate the
system. The illustration and descriptions below highlight some of the
keypad features:

32-Character Keypad

3

Special Security Command Messages

As you use your system, you’ll occasionally see a keypad display
that asks you to enter a user code or that describes a condition on
the system. Below are some examples of the displays you'll see:

ALARM

A 24 hour zone (for example, fire or panic) or an armed burglary zone
has been faulted. Your system may sound bells or sirens.

ALARM CANCELLED

An authorized user has cancelled an alarm condition by entering
their user code.

TROUBLE

There is a problem with a protection device or system component.
This display is accompanied by a description of the problem.

ENTER CODE

The system requires you to enter a personal user code. User codes
can be required for turning your system on (arming), turning your
system off (disarming), and many other system options.

As you enter your user code, the keypad display shows an asterisk
(*) in place of each digit pressed. This keeps others from seeing your
user code on the display as it’s entered.

TRY AGAIN

The user code entered is not recognized by the system. Check the
user code and try again.

INVALID CODE

The user code you've entered is considered invalid by the system.

Introduction

SYSTEM TROUBLE or SERVICE REQUIRED

There is an electronic failure in your system. Contact the service
department as soon as possible.

Special Security Command Tones

Your keypad also contains a small speaker that allows it to alert you
to events as they occur on your system. Below are brief descriptions
of the different tones you'll hear from the keypad:

Fire alert: Your keypad may sound a fire tone to alert persons in the
vicinity to the alarm condition. This is in addition to the bell output
from the alarm panel.

Burglary alert: Your keypad may sound a burglary tone to alert
persons in the vicinity to the alarm condition. This is in addition to the
bell output from the alarm panel.

Key press tone: A short beep as you press a key on the keypad.
Prewarn tone: A continuous pulsed tone that sounds when you

open an entry delay door on a system that is armed (turned on)
reminding you to disarm the burglary protection.

Monitor tone: A pulsed tone for one second, one pulse only that
sounds whenever a door or window is opened while you’re using the
zone monitor function from the User Menu. See Zone Monitor.

Trouble tone: A steady tone indicating a trouble condition on your
system. Press a SELECT key to silence the trouble tone.

As you use your system, you’ll occasionally see a keypad display
that asks you to enter a user code or that describes a condition on
the system. Below are some examples of the displays you'll see:

ALARM

A 24 hour zone (for example, fire or panic) or an armed burglary zone
has been faulted. Your system may sound bells or sirens.

ALARM CANCELLED

An authorized user has cancelled an alarm condition by entering
their user code.

TROUBLE

There is a problem with a protection device or system component.
This display is accompanied by a description of the problem.

SYSTEM TROUBLE or SERVICE REQUIRED

There is an electronic failure in your system. Contact the service
department as soon as possible.

Special Security Command Tones

Your keypad also contains a small speaker that allows it to alert you
to events as they occur on your system. Below are brief descriptions
of the different tones you'll hear from the keypad:

Fire alert: Your keypad may sound a fire tone to alert persons in the
vicinity to the alarm condition. This is in addition to the bell output
from the alarm panel.

Burglary alert: Your keypad may sound a burglary tone to alert
persons in the vicinity to the alarm condition. This is in addition to the

Special Security Command Messages

4

Understanding Security System Terms

Throughout this guide, and in some displays on your keypad, you’ll
see certain words or phrases that might be unfamiliar. Although
every effort has been made to use terms that are commonly known,
there are some for which there was no acceptable substitute.

Below are some terms you’ll see here and on your keypad display:

Arming

This is the term used for turning on the burglary protection in one or
more areas of the system. Your system may require you to enter a
user code. When armed, the system is able to sound alarm bells or
sirens and, if monitored, send alarm reports to a central station when
a burglary zone is faulted.

Fire, panic, and other 24 hour devices are always turned on and do
not need to be armed.

Disarming

This means turning off one or more areas of the system. When
disarmed, the system does NOT sound alarms or send alarm
reports to a central station when a burglary zone is faulted.

Zone

A zone refers to a group of one or more protected openings or
protection devices assigned the same zone number. Each door or
window, motion detector, smoke detector, or other device has a
zone number and a name.

Often, similar devices in the same general area will share the same
zone. For example, the windows on the east side of the premises
can all be grouped together in a zone named E. WINDOWS.

Introduction

Entry or Exit Zone

Almost all systems have one or more doors through which you can
enter or exit the premises. These doors are programmed with a
delay time to allow you to enter or exit while the system is armed
without setting off the alarm.

When you arm the system, activity on all burglary zones is ignored
until the programmed exit

delay time expires. Once that time has
expired and the system is fully armed, opening the door causes the
panel to start the

entry

delay time. During the entry delay time, you
must enter a valid user code to disarm the system or an alarm will
occur.

Instant Zone

Exterior windows and non entry doors, or interior protection devices,
are typically not programmed with delay times. If these zones are
faulted while the system is armed, an alarm occurs instantly.

24 Hour Zone

A 24 hour zone is never assigned to an area and is not turned on or
off by arming or disarming your system. Some examples of 24 hour
zones are: fire zones, panic zones, and temperature control zones.

Areas

An area is made up of burglary zones that can be armed or disarmed
together. The Perimeter area, for example, consists of all the doors
and windows on the outside of the building. When you arm the
Perimeter, these zones sound an alarm if tripped.

Understanding Security System Terms

Throughout this guide, and in some displays on your keypad, you’ll
see certain words or phrases that might be unfamiliar. Although
every effort has been made to use terms that are commonly known,
there are some for which there was no acceptable substitute.

Below are some terms you’ll see here and on your keypad display:

Arming

This is the term used for turning on the burglary protection in one or
more areas of the system. Your system may require you to enter a
user code. When armed, the system is able to sound alarm bells or
sirens and, if monitored, send alarm reports to a central station when
a burglary zone is faulted.

Fire, panic, and other 24 hour devices are always turned on and do
not need to be armed.

Entry or Exit Zone

Almost all systems have one or more doors through which you can
enter or exit the premises. These doors are programmed with a
delay time to allow you to enter or exit while the system is armed
without setting off the alarm.

When you arm the system, activity on all burglary zones is ignored
until the programmed exit

delay time expires. Once that time has
expired and the system is fully armed, opening the door causes the
panel to start the

entry

delay time. During the entry delay time, you
must enter a valid user code to disarm the system or an alarm will
occur.

Instant Zone

Exterior windows and non entry doors, or interior protection devices,

5

Central Station Monitoring

Your system can also be programmed to automatically send alarm,
trouble, and arming and disarming reports to a central station.
Operators at the central station can in turn dispatch the appropriate
authorities or contact you with the specific event information.

Status

Status is a feature that automatically displays the armed or disarmed
status of your system on the Security Command keypads. Alarm or
trouble conditions on a zone or a system monitor such as AC or
battery trouble can also be displayed. There are two types of status
information available: Armed Status and Status List.

Armed Status

With Armed Status, the keypad displays the current armed condition
of areas within your security system.

The keypad displays When
PERIMETER ON The perimeter areas are on
ALL SYSTEM ON All areas are on
PERIM/INT ON The perimeter and interior areas are on

but the bedroom area is off

Status List

The keypad Status List displays any alarm or trouble condition on a
zone and any trouble condition that occurs with the AC power or
battery power. If more than one alarm or trouble condition occurs at
the same time, the keypad sequences this information on its display.

Introduction

If your system contains any Panic zones, these are

not

displayed on

the keypad for security reasons.
If an alarm occurs on a non-fire 24 hour zone or a system monitor,

it remains in the Status List until it restores. If one or more armed
burglary zones trips, the last one to trip remains in the Status List.
The burglary zone alarm remains in the Status List for several
minutes or until it's cleared by disarming the system.

Exit Error

This is an automatic function of the panel that prevents an alarm
from occurring if an exit door doesn't close all the way after the
system has been armed. Here's how it works:

You close all doors and windows, arm the system, and then leave
by the front door. You close the door but it doesn't latch and opens
slightly causing the front door zone to show as an open to the
system. After the exit delay time expires the system attempts to arm
the front door zone but recognizes the open condition and, instead
of sending an alarm report to the central station, sends an Exit Error
report and force arms the door. (If the door closes at a later time it
will be included back into the system.) The system sounds the alarm
sirens for 15 seconds to alert you of the condition and provide an
opportunity for you to close the door.

The Exit Error feature allows the central station to acknowledge the
arming error without dispatching the police on a false alarm.

Central Station Monitoring

Your system can also be programmed to automatically send alarm,
trouble, and arming and disarming reports to a central station.
Operators at the central station can in turn dispatch the appropriate
authorities or contact you with the specific event information.

Status

Status is a feature that automatically displays the armed or disarmed
status of your system on the Security Command keypads. Alarm or
trouble conditions on a zone or a system monitor such as AC or
battery trouble can also be displayed. There are two types of status
information available: Armed Status and Status List.

Armed Status

If your system contains any Panic zones, these are

not

displayed on

the keypad for security reasons.
If an alarm occurs on a non-fire 24 hour zone or a system monitor,

it remains in the Status List until it restores. If one or more armed
burglary zones trips, the last one to trip remains in the Status List.
The burglary zone alarm remains in the Status List for several
minutes or until it's cleared by disarming the system.

Exit Error

This is an automatic function of the panel that prevents an alarm
from occurring if an exit door doesn't close all the way after the
system has been armed. Here's how it works:

Understanding Security System Terms

Understanding Security System Terms

6

How your System Operates

Your system has been programmed to operate in one of three
modes: Area Arming, All/Perimeter, or Home/Sleep/Away.

• Area Arming - Your burglary protection is divided into up to four
areas. Each area can have a custom name, be turned on or off
independently of other areas, and limit access to only those users
with the proper authority.

• All/Perimeter - Your burglary protection is divided into two areas:
Interior and Perimeter. You can turn on the just the Perimeter
protection while inside for security or turn on both as you leave.

• Home/Sleep/Away - Your burglary protection is divided into three
areas: Interior, Perimeter, and Bedrooms. You can turn on the
Perimeter, Perimeter and Interior, or all three areas separately.

Regardless of which mode has been programmed, much of the
operation is similar. Throughout this guide, any differences between
the systems are noted for your convenience.

Arming Functions

Bypassing: After making your arming selection, the keypad displays

any zones that have been bypassed while the system was disarmed.
These zones remain bypassed until the system is disarmed. Any 24
hour zones in a bad condition are also displayed.

During arming, the system verifies that all doors, windows, and other
protection devices to be armed are in normal condition.
If everything is okay, the system arms. If there is a problem on one
or more burglary zones the keypad displays the problem and allows
you to bypass those zones.

Introduction

If the problem can be corrected by closing a door or window, do not
bypass the zone. Instead, correct the problem and try arming again.
If the problem cannot be corrected, you can bypass the zone or wait
until the zone can be repaired by a service technician. A bypassed
zone is ignored by the system during the armed period.

In some cases, you might see the keypad display FRONT DOOR
BAD *. The asterisk next to BAD means that the zone is a priority
zone, which cannot be bypassed. The problem on the zone must be
corrected before the system can be armed.

Armed Message: After all bypassing is completed or zone faults
corrected, the areas you selected are armed. The keypad briefly
displays ALL SYSTEM ON if all areas in the system are arming and
PERIMETER ON or PERIM/INT ON if only selected areas are
arming. The keypad then displays the exit delay as it counts down.
Zones are not armed until the exit delay time expires.

If your system uses a keyswitch to arm an area, the exit delay time
is NOT shown on the keypad display.

DIALING . . . Message: If your system is monitored, it may be
programmed to wait for the arming report to be sent to the central
station before displaying the armed message. See Arming Report
below. This is to verify your phone lines are working properly. While

the system is waiting, the display reads DIALING.... If the report is

received, the keypad buzzes for one second and displays the armed
message. If the report is not received, the keypad displays LOCAL

ALARM ONLY before displaying the armed message.
Arming Report: Your system can be programmed to send arming

or zone bypassing reports to a central station. This feature is
optional and can be programmed for you at any time.

How your System Operates

Your system has been programmed to operate in one of three
modes: Area Arming, All/Perimeter, or Home/Sleep/Away.

• Area Arming - Your burglary protection is divided into up to four
areas. Each area can have a custom name, be turned on or off
independently of other areas, and limit access to only those users
with the proper authority.

• All/Perimeter - Your burglary protection is divided into two areas:
Interior and Perimeter. You can turn on the just the Perimeter
protection while inside for security or turn on both as you leave.

• Home/Sleep/Away - Your burglary protection is divided into three
areas: Interior, Perimeter, and Bedrooms. You can turn on the
Perimeter, Perimeter and Interior, or all three areas separately.

If the problem can be corrected by closing a door or window, do not
bypass the zone. Instead, correct the problem and try arming again.
If the problem cannot be corrected, you can bypass the zone or wait
until the zone can be repaired by a service technician. A bypassed
zone is ignored by the system during the armed period.

In some cases, you might see the keypad display FRONT DOOR
BAD *. The asterisk next to BAD means that the zone is a priority
zone, which cannot be bypassed. The problem on the zone must be
corrected before the system can be armed.

Armed Message: After all bypassing is completed or zone faults
corrected, the areas you selected are armed. The keypad briefly
displays ALL SYSTEM ON if all areas in the system are arming and
PERIMETER ON or PERIM/INT ON if only selected areas are

7

Area System Arming

Area Assignment: Your security system has been programmed

into separate areas. The number of areas and their names are listed
in the back of this guide.

Arming or Disarming: You can arm and disarm all areas at one
time or each area individually. You can only arm or disarm areas
authorized for your user code.

All or Selective Arming: After entering your user code, the system
allows you to arm either all of the areas to which you have access
or one or more selected areas. If you choose to arm all areas, the
system begins verifying that all zones in those areas are in a good
condition. If you choose to arm selected areas, the system prompts
you to choose the areas you want to arm.

Arming the System

1. Press the COMMAND key until ARM DISARM displays.

2. Select ARM to turn on all protection.

3. Enter your user code if required. The display reads ALL? NO
YES.

4. Select NO to arm only selected areas. Go to step 5. Select YES
to arm all areas authorized for your user code.

5. If NO is selected in step 4, the display begins to list each area
to which you have access followed by NO YES.

Example: OFFICE NO YES.
5a. Select YES for each area you want to arm.
5b. Select NO for each area you do NOT want to arm.

Arming and Disarming

Note: You can also just press the area numbers you want to arm

while at the ALL? NO YES display. This changes the display
to AREAS:. The numbers you select appear in the display. For
example: AREAS: 2 4. Press COMMAND when done.

6. The system displays any zones that have been bypassed prior
to arming and any bad 24 hour zones. No action is required.

7. At this point you can force arm or bypass any bad zones. A
zone that is force armed will be restored into the system if it later
returns to normal. A zone that is bypassed will remain bypassed
until the system is disarmed. See steps 7a through 7d.

7a. If a problem exists on any zones, the zone name and

problem are shown followed by: OKAY BYPASS STOP.
7b. Select OKAY to force arm the zone(s) before arming.
7c. Select BYPASS to bypass the zone(s) before arming.
7d. Select STOP to stop the system from arming. Correct the

zone problem(s) and return to step 1.

8. The display reads SYSTEM ON if at least one area in the
system is armed, and ALL SYSTEM ON if all areas in the
system are armed.

9. The keypad then displays the exit time in seconds and counts
down the remaining time: EXIT: # # (# # = seconds remaining).
The exit zones arm when the delay time expires.

Area System Arming

Area Assignment: Your security system has been programmed

into separate areas. The number of areas and their names are listed
in the back of this guide.

Arming or Disarming: You can arm and disarm all areas at one
time or each area individually. You can only arm or disarm areas
authorized for your user code.

All or Selective Arming: After entering your user code, the system
allows you to arm either all of the areas to which you have access
or one or more selected areas. If you choose to arm all areas, the
system begins verifying that all zones in those areas are in a good
condition. If you choose to arm selected areas, the system prompts
you to choose the areas you want to arm.

Arming the System

Note: You can also just press the area numbers you want to arm

while at the ALL? NO YES display. This changes the display
to AREAS:. The numbers you select appear in the display. For
example: AREAS: 2 4. Press COMMAND when done.

6. The system displays any zones that have been bypassed prior
to arming and any bad 24 hour zones. No action is required.

7. At this point you can force arm or bypass any bad zones. A
zone that is force armed will be restored into the system if it later
returns to normal. A zone that is bypassed will remain bypassed
until the system is disarmed. See steps 7a through 7d.

7a. If a problem exists on any zones, the zone name and

problem are shown followed by: OKAY BYPASS STOP.

7b. Select OKAY to force arm the zone(s) before arming.

8

Area System Disarming

Disarming: While the system is armed, you can only enter the

premises through an exit/entry delay door without causing an alarm.
After opening the door, the Security Command keypad sounds a
prewarn tone to remind you to disarm the system. You must disarm
the system before the delay time expires or an alarm on the door
zone will occur.

During the prewarn tone, the keypad displays ENTER CODE: Enter
your user code to disarm the system. Only those areas authorized
for your user code will disarm.

All or Selective Arming: After entering your user code, the system
allows you to disarm either all of the areas to which you have access
or just selected areas. If you choose to disarm all areas, the system
automatically disarms them. If you choose to disarm selected areas,
the names of those areas will be displayed on the keypad.

Alarm Display: After disarming, the keypad displays any zones that
went into alarm or any communication problems that occurred
during the armed period. All burglary zones are then disarmed and
any bypassed zones are automatically reset.

Disarmed Message: The keypad displays ALL SYSTEM OFF after
the system disarms.

Central Station Report: A report of the disarming can be sent to the
central station. If your system does not have this feature, it can be
programmed for you at any time.

Disarming an Area System

1. Press the COMMAND key until ARM DISARM is displayed.
During entry delay this process starts at step 3 below.

2. Select DISARM to disarm areas.

3. The keypad displays ENTER CODE: . Enter your user code and
press COMMAND. The keypad displays ALL? NO YES.

4. Select YES to disarm all areas authorized for your user code.
4a. Select NO to disarm only certain areas individually. The

keypad then displays the name of each area authorized for your
code followed by the NO YES display.

4b. Choose YES to disarm the area displayed.
4c. Choose NO to not disarm and to display the next area.
Note: You can also just press the area numbers you want to

disarm while at the ALL? NO YES display. This changes the
display to AREAS: . The area numbers you select appear in
the display. For example: AREAS: 2 4.

To remove an area number from the display, press its
corresponding number on the keypad.

Press COMMAND when done.

5. After all areas have been displayed, any alarms or
communication problems that occurred during the armed
period are shown.

6. If all areas have been disarmed, the keypad displays ALL
SYSTEM OFF.

Arming and Disarming

Area System Disarming

Disarming: While the system is armed, you can only enter the

premises through an exit/entry delay door without causing an alarm.
After opening the door, the Security Command keypad sounds a
prewarn tone to remind you to disarm the system. You must disarm
the system before the delay time expires or an alarm on the door
zone will occur.

During the prewarn tone, the keypad displays ENTER CODE: Enter
your user code to disarm the system. Only those areas authorized
for your user code will disarm.

All or Selective Arming: After entering your user code, the system
allows you to disarm either all of the areas to which you have access
or just selected areas. If you choose to disarm all areas, the system
automatically disarms them. If you choose to disarm selected areas,

Disarming an Area System

1. Press the COMMAND key until ARM DISARM is displayed.
During entry delay this process starts at step 3 below.

2. Select DISARM to disarm areas.

3. The keypad displays ENTER CODE: . Enter your user code and
press COMMAND. The keypad displays ALL? NO YES.

4. Select YES to disarm all areas authorized for your user code.
4a. Select NO to disarm only certain areas individually. The

keypad then displays the name of each area authorized for your
code followed by the NO YES display.

4b. Choose YES to disarm the area displayed.
4c. Choose NO to not disarm and to display the next area.

9

All/Perimeter System Arming

Area Assignment: Your security system is divided into two separate

areas. Motion detectors, inside doors, and other interior protection
devices are assigned to the

Interior

area while windows and exterior

doors are assigned to the

Perimeter

area.

Perimeter or All: When arming an All/Perimeter system, the
keypad displays PERIM ALL. If you select ALL, you arm both the
Perimeter and the Interior of the system. You’ll want to arm both of
these areas when leaving with nobody left inside. Selecting PERIM
arms only the Perimeter of the system. Perimeter arming is for when
you’re staying inside but want the comfort of knowing the exterior
doors and windows are armed. Perimeter arming allows you to
move freely about inside without setting off any interior alarms.

System Ready/System Not Ready Keypad Displays

When all zones in the system are in a normal condition, the keypad
displays SYSTEM READY. If there are one or more zones that are
not in a normal condition, the keypad displays SYSTEM NOT
READY. Pressing any top row SELECT key during this display
shows the zone name allowing you to investigate the problem.

Instant Arming

Instant: During the exit delay time, you can cancel the exit and entry

delays and cause all zones to be instant zones. Just press the far
right select key under INSTNT while the exit delay is displayed. This
immediately arms the exit zones. However, no entry delay is
provided and an alarm will occur should an entry door be opened.

Arming an All/Perimeter System

1. Enter your code. The keypad displays PERIM ALL.

2. Select PERIM to arm the Perimeter area only.

3. Select ALL to arm both the Perimeter and Interior areas.

4. The keypad displays any bypassed zones and 24 hour zones
that are in a bad condition. No action is required by you.

5. At this point you can force arm or bypass any bad zones. A
zone that is force armed will be restored into the system if it later
returns to normal. A zone that is bypassed will remain bypassed
until the system is disarmed. See steps 5a through 5d.

5a. If a problem exists on any zones, the zone name and

problem are shown followed by: OKAY BYPASS STOP.
5b. Select OKAY to force arm the zone(s) before arming.
5c. Select BYPASS to bypass the zone(s) before arming.
5d. Select STOP to stop the system from arming. Correct the

zone problem(s) and return to step 1.

6. The keypad displays PERIMETER ON if only the perimeter is
being armed and ALL SYSTEM ON if both the perimeter and
interior are being armed.

7. The keypad next displays EXIT: ## INSTNT and begins to
count down the number of seconds remaining for you to exit.
When the delay expires, all zones are armed.

8. You can select INSTNT while EXIT: ## INSTNT is displayed to
immediately arm all zones and make them instant. The keypad
displays INSTANT.

9. When the system is fully armed, the keypad displays
PERIMETER ON for perimeter arming and ALL SYSTEM ON
for perimeter and interior arming.

Arming and Disarming

All/Perimeter System Arming

Area Assignment: Your security system is divided into two separate

areas. Motion detectors, inside doors, and other interior protection
devices are assigned to the

Interior

area while windows and exterior

doors are assigned to the

Perimeter

area.

Perimeter or All: When arming an All/Perimeter system, the
keypad displays PERIM ALL. If you select ALL, you arm both the
Perimeter and the Interior of the system. You’ll want to arm both of
these areas when leaving with nobody left inside. Selecting PERIM
arms only the Perimeter of the system. Perimeter arming is for when
you’re staying inside but want the comfort of knowing the exterior
doors and windows are armed. Perimeter arming allows you to
move freely about inside without setting off any interior alarms.

System Ready/System Not Ready Keypad Displays

3. Select ALL to arm both the Perimeter and Interior areas.

4. The keypad displays any bypassed zones and 24 hour zones
that are in a bad condition. No action is required by you.

5. At this point you can force arm or bypass any bad zones. A
zone that is force armed will be restored into the system if it later
returns to normal. A zone that is bypassed will remain bypassed
until the system is disarmed. See steps 5a through 5d.

5a. If a problem exists on any zones, the zone name and

problem are shown followed by: OKAY BYPASS STOP.
5b. Select OKAY to force arm the zone(s) before arming.
5c. Select BYPASS to bypass the zone(s) before arming.
5d. Select STOP to stop the system from arming. Correct the

zone problem(s) and return to step 1.

10

All/Perimeter System Disarming

Disarming: While the system is armed, you can only enter the

premises through an entry/exit delay door without causing an alarm.
After opening the door, the Security Command keypad sounds a
prewarn tone to remind you to disarm the system. You must disarm
the system before the prewarn tone expires or an alarm on the door
zone will occur.

During the prewarn tone, the keypad displays ENTER CODE:. Enter
your user code to disarm the system.

Alarm Display: After disarming, the keypad displays any zones that
tripped or any transmission problems that occurred during the
armed period. All burglary zones are then disarmed and any
bypassed zones are automatically reset.

Disarmed Message: The keypad displays ALL SYSTEM OFF after
the system disarms.

Central Station Report: A report of the system disarming can be
transmitted to the central station. This is optional and can be
programmed for you at any time.

Arming and Disarming

Disarming an All/Perimeter System

1. During the entry delay time, the keypad displays ENTER
CODE: . Enter your user code.

2. The keypad then displays any zones that went into alarm or any
communication problems that occurred during the armed period.

3. The keypad next displays ALL SYSTEM OFF to confirm the
system is disarmed.

Disarming During an Alarm

1. While the alarm bell or siren is sounding, enter your user code.
The keypad displays DISARM SILENCE.

2. Press the SELECT key under DISARM to disarm the system
and silence the alarm.

The keypad next displays ALL SYSTEM OFF to confirm the
system is disarmed.

3. Press the SELECT key under SILENCE to stop the bell or siren
but NOT disarm the system.

If you do not press any SELECT key, or you press the COMMAND
key, the system will automatically disarm and silence the alarm.

4. If your system is programmed to send an Abort (alarm cancel)
report to the central station, the keypad displays ALARM

CANCELLED.

All/Perimeter System Disarming

Disarming: While the system is armed, you can only enter the

premises through an entry/exit delay door without causing an alarm.
After opening the door, the Security Command keypad sounds a
prewarn tone to remind you to disarm the system. You must disarm
the system before the prewarn tone expires or an alarm on the door
zone will occur.

During the prewarn tone, the keypad displays ENTER CODE:. Enter
your user code to disarm the system.

Alarm Display: After disarming, the keypad displays any zones that
tripped or any transmission problems that occurred during the
armed period. All burglary zones are then disarmed and any
bypassed zones are automatically reset.

Disarmed Message: The keypad displays ALL SYSTEM OFF after

Disarming an All/Perimeter System

1. During the entry delay time, the keypad displays ENTER
CODE: . Enter your user code.

2. The keypad then displays any zones that went into alarm or any
communication problems that occurred during the armed period.

3. The keypad next displays ALL SYSTEM OFF to confirm the
system is disarmed.

Disarming During an Alarm

1. While the alarm bell or siren is sounding, enter your user code.
The keypad displays DISARM SILENCE.

2. Press the SELECT key under DISARM to disarm the system

11

Home/Away System Arming

Area Assignment: Your security system is divided into two or three

separate areas. Motion detectors, inside doors, and other interior
devices are assigned to an

Interior

and possibly

Bedroom

area while

windows and exterior doors, are assigned to a

Perimeter

area.

Arming the system: When arming a Home/Away system, the
keypad displays HOME AWAY or HOME SLEEP AWAY. If you
select AWAY, you arm all areas of the system. You’ll want to arm all
areas when leaving with nobody staying inside. Selecting HOME
arms only the Perimeter of the system. Perimeter arming is for when
you’re staying inside but want the comfort of knowing the exterior
doors and windows are armed. Selecting SLEEP arms the Perimeter
and Interior devices but leaves devices near bedrooms or other
nighttime areas off.

System Ready/System Not Ready Keypad Displays

When all zones in the system are in a normal condition and can be
armed without bypassing, the keypad displays SYSTEM READY. If
there are one or more zones that are not in a normal condition, the
keypad displays SYSTEM NOT READY. Pressing any top row
SELECT key during this display shows the bad zone name.

Arming a Home/Away System

1. Enter your 4-digit user code. The keypad displays HOME
AWAY or HOME SLEEP AWAY (you may have three areas).

2. Select HOME to arm the Perimeter only.

3. Select SLEEP to arm the Perimeter and Interior.

4. Select AWAY to arm the Perimeter, Interior, and Bedroom.

5. The keypad displays zones that have been bypassed prior to
arming and 24 hour zones that are in a bad condition. No action
is required by you.

5. At this point you can force arm or bypass any bad zones. A
zone that is force armed will be restored into the system if it later
returns to normal. A zone that is bypassed will remain bypassed
until the system is disarmed. See steps 5a through 5d.

5a. If a problem exists on any zones, the zone name and

problem are shown followed by: OKAY BYPASS STOP.
5b. Select OKAY to force arm the zone(s) before arming.
5c. Select BYPASS to bypass the zone(s) before arming.
5d. Select STOP to stop the system from arming. Correct the

zone problem(s) and return to step 1.

7. The keypad displays PERIMETER ON if you selected HOME,
or PERIM/INT ON if you selected SLEEP, or ALL SYSTEM ON
if you selected AWAY.

8. The keypad next displays EXIT: ## INSTNT and begins to
count down the number of seconds remaining for you to exit.
When the delay expires, all zones are armed.

9. You can select INSTNT while EXIT: ## INSTNT is displayed to
immediately arm all zones and make them instant. The keypad
displays INSTANT.

10. When the system is fully armed, the keypad displays
PERIMETER ON for Perimeter arming, PERIM/INT ON for
Perimeter and Interior arming, and ALL SYSTEM ON for all
areas armed.

Arming and Disarming

Home/Away System Arming

Area Assignment: Your security system is divided into two or three

separate areas. Motion detectors, inside doors, and other interior
devices are assigned to an

Interior

and possibly

Bedroom

area while

windows and exterior doors, are assigned to a

Perimeter

area.

Arming the system: When arming a Home/Away system, the
keypad displays HOME AWAY or HOME SLEEP AWAY. If you
select AWAY, you arm all areas of the system. You’ll want to arm all
areas when leaving with nobody staying inside. Selecting HOME
arms only the Perimeter of the system. Perimeter arming is for when
you’re staying inside but want the comfort of knowing the exterior
doors and windows are armed. Selecting SLEEP arms the Perimeter
and Interior devices but leaves devices near bedrooms or other
nighttime areas off.

5. The keypad displays zones that have been bypassed prior to
arming and 24 hour zones that are in a bad condition. No action
is required by you.

5. At this point you can force arm or bypass any bad zones. A
zone that is force armed will be restored into the system if it later
returns to normal. A zone that is bypassed will remain bypassed
until the system is disarmed. See steps 5a through 5d.

5a. If a problem exists on any zones, the zone name and

problem are shown followed by: OKAY BYPASS STOP.
5b. Select OKAY to force arm the zone(s) before arming.
5c. Select BYPASS to bypass the zone(s) before arming.
5d. Select STOP to stop the system from arming. Correct the

zone problem(s) and return to step 1.

12

Home/Away System Disarming

Disarming: While the system is armed, you can only enter the

premises through an entry/exit delay door without causing an alarm.
After opening the door, the keypad sounds a prewarn tone to remind
you to disarm the system. You must disarm the system before the
prewarn tone expires or an alarm on the door zone will occur.

During the prewarn tone, the keypad displays ENTER CODE:. Enter
your code to disarm the system.

Alarm Display: After disarming, the keypad displays any zones that
tripped or any communication problems that occurred during the
armed period. All burglary zones are then disarmed and any
bypassed zones are automatically reset.

Disarmed Message: The keypad displays ALL SYSTEM OFF after
the system disarms.

Central Station Report: A report of the system disarming can be
transmitted to the central station. This is optional and can be
programmed for you at any time.

Easy Exit™ Feature

While the system is armed, you can also just press the COMMAND
and then the 9 key to restart the exit delays to allow you to exit the
premises without disarming the system. After the exit delay time
expires, the system rearms automatically. This feature allows you to
get the paper, let your pet out, or leave for work without having to
disarm and then rearm the system.

Arming and Disarming

Disarming a Home/Away System

1. During the entry delay, the keypad displays ENTER CODE:.
Enter your 4 digit user code.

2. The keypad then displays any alarms or communication
problems that occurred during the armed period.

3. The keypad next displays ALL SYSTEM OFF to confirm the
system is disarmed.

Disarming During an Alarm

1. While the alarm bell or siren is sounding, enter your 4 digit user
code. The keypad displays DISARM SILENCE.

2. Press the SELECT key under DISARM to disarm the system
and silence the alarm.

The keypad next displays ALL SYSTEM OFF to confirm the
system is disarmed.

3. Press the SELECT key under SILENCE to stop the bell or siren
but NOT disarm the system.

If you do not press any SELECT key, or you press the COMMAND
key, the system will automatically disarm and silence the alarm.

4. If your system is programmed to send an Abort (alarm cancel)
report to the central station, the keypad displays ALARM

CANCELLED.

Home/Away System Disarming

Disarming: While the system is armed, you can only enter the

premises through an entry/exit delay door without causing an alarm.
After opening the door, the keypad sounds a prewarn tone to remind
you to disarm the system. You must disarm the system before the
prewarn tone expires or an alarm on the door zone will occur.

During the prewarn tone, the keypad displays ENTER CODE:. Enter
your code to disarm the system.

Alarm Display: After disarming, the keypad displays any zones that
tripped or any communication problems that occurred during the
armed period. All burglary zones are then disarmed and any
bypassed zones are automatically reset.

Disarmed Message: The keypad displays ALL SYSTEM OFF after
the system disarms.

Disarming a Home/Away System

1. During the entry delay, the keypad displays ENTER CODE:.
Enter your 4 digit user code.

2. The keypad then displays any alarms or communication
problems that occurred during the armed period.

3. The keypad next displays ALL SYSTEM OFF to confirm the
system is disarmed.

Disarming During an Alarm

1. While the alarm bell or siren is sounding, enter your 4 digit user
code. The keypad displays DISARM SILENCE.

2. Press the SELECT key under DISARM to disarm the system

13

Security Command User Menu

Many of the features of your system have been put into a User Menu
you can access from any Security Command keypad.

To access the User Menu:

1. Press the COMMAND key until MENU? NO YES displays.

2. Select YES. The keypad displays ENTER CODE: –. Enter your
user code. You can now scroll down through the list of system
features available to your authority level.

The following pages detail each User Menu item and provide
instructions on when and how to use them properly.

User Checkin

User Code Level: Master or Standard
Function: This feature allows you to monitor the arrival of latchkey

children or employees by having a special Checkin Report sent to
your alphanumeric or numeric pager. Your system must be
programmed for the Pager Direct™ option. The Appendix section of
this guide contains Quick Reference cards for your wallet or purse.

Sending a Checkin Report:

1. After disarming the system, access the User Menu.
(Or press the COMMAND then 7 key and enter your user code

to send a Checkin Report. This feature operates on 32-character
keypads only.)

2. At the USER CHECKIN? display, press any SELECT key. The
keypad displays USER CHECKIN: 22 ( 22 = user number).

3. The panel sends the Checkin Report containing your account
number and user number to the pager.

Sensor Reset

User Code Level: Master or Standard
Function: Resets smoke or glassbreak detectors. Also clears Fire

and Supervisory zone alarm and trouble keypad displays. Sensor
Reset also clears low battery displays if your system is using
wireless sensors.

Once smoke or glassbreak detectors have tripped, they must be
reset before they can detect any additional alarm conditions. When
Sensor Reset is selected, power to the detectors is temporarily
removed by the system allowing them to reset.

Make sure all smoke is cleared from around the area of the smoke
detectors before performing a Sensor Reset to prevent the alarm
from occurring again.

Resetting the Sensors

1. Access the User Menu.

2. When SENSOR RESET? is displayed, press any SELECT key.
The keypad displays SENSORS OFF for five seconds followed
by SENSORS ON.

3. The keypad returns to the status display.

Enter your user code to reset sensors

While your system is disarmed, you can just enter your user code
and press COMMAND to reset the sensors. (This feature operates
in All/Perimeter and Home/Away systems only.)

This also activates the door strike if your system has an Easy
Entry™ access control keypad.

User Menu

Security Command User Menu

Many of the features of your system have been put into a User Menu
you can access from any Security Command keypad.

To access the User Menu:

1. Press the COMMAND key until MENU? NO YES displays.

2. Select YES. The keypad displays ENTER CODE: –. Enter your
user code. You can now scroll down through the list of system
features available to your authority level.

The following pages detail each User Menu item and provide
instructions on when and how to use them properly.

User Checkin

User Code Level: Master or Standard

Sensor Reset

User Code Level: Master or Standard
Function: Resets smoke or glassbreak detectors. Also clears Fire

and Supervisory zone alarm and trouble keypad displays. Sensor
Reset also clears low battery displays if your system is using
wireless sensors.

Once smoke or glassbreak detectors have tripped, they must be
reset before they can detect any additional alarm conditions. When
Sensor Reset is selected, power to the detectors is temporarily
removed by the system allowing them to reset.

Make sure all smoke is cleared from around the area of the smoke
detectors before performing a Sensor Reset to prevent the alarm
from occurring again.

14

Outputs On Off

User Code Level: Master or Standard.
Function: Allows you to turn the system's outputs on and off.

This function is used to individually turn your system’s relay outputs
on and off. Your system may use these outputs to control interior and
exterior lighting, or heating, air conditioning, or other appliances.

The names and numbers of the outputs on your system are located
in the System Setup section at the back of this guide.

Turning the Outputs On and Off

1. Access the User Menu.

2. Press the COMMAND key until OUTPUTS ON/OFF? displays.

3. Press any one of the SELECT keys.

4. The keypad displays OUTPUT: - ON OFF.

5. Enter the output number you want to turn on or off. The output
number appears in the display.

6. With the output number displayed, press the SELECT key
under ON or OFF. The output is then turned on or off, depending
on your selection, and remains in that state until you change it.

7. The system automatically removes the output number and a
new output number can be entered. Refer back to step 5.

To exit the Output menu option, press the ARROW key until you've
returned to the keypad's Status List.

Bypass Zones

User Code Level: Master or Standard.
Function: Allows you to bypass a zone prior to arming the system.

Bypassing is usually done when a zone cannot be restored to normal
and you want to arm the system. Once bypassed, the system will not
respond to any activity on the zone.

A zone can be bypassed only while it's disarmed. Since Fire, Panic,
Emergency, and Supervisory zones are always armed, they can
never be bypassed.

The Bypass Zones function can also be used to restore a bypassed
zone back into the system. This can only be done while the zone is
disarmed.

When Bypass Zones is selected, a report of the bypassing can be
sent to your central station. This is optional and can be programmed
for you at any time.

Using the Bypass Zones Function

1. Access the User Menu.

2. Press the COMMAND key until BYPASS ZONES? displays.

3. Press any one of the SELECT keys. The keypad displays

ZONE: - RST BYPS.

4. To reset a zone, enter the zone number and press the SELECT
key under RST.

5. To Bypass a zone, enter the zone number and press the
SELECT key under BYPS.

User Menu

Outputs On Off

User Code Level: Master or Standard.
Function: Allows you to turn the system's outputs on and off.

This function is used to individually turn your system’s relay outputs
on and off. Your system may use these outputs to control interior and
exterior lighting, or heating, air conditioning, or other appliances.

The names and numbers of the outputs on your system are located
in the System Setup section at the back of this guide.

Turning the Outputs On and Off

1. Access the User Menu.

2. Press the COMMAND key until OUTPUTS ON/OFF? displays.

3. Press any one of the SELECT keys.

Bypass Zones

User Code Level: Master or Standard.
Function: Allows you to bypass a zone prior to arming the system.

Bypassing is usually done when a zone cannot be restored to normal
and you want to arm the system. Once bypassed, the system will not
respond to any activity on the zone.

A zone can be bypassed only while it's disarmed. Since Fire, Panic,
Emergency, and Supervisory zones are always armed, they can
never be bypassed.

The Bypass Zones function can also be used to restore a bypassed
zone back into the system. This can only be done while the zone is
disarmed.

15

User Menu

Zone Monitor

User Code Level: Master and Standard.
Function: Allows the system to monitor selected disarmed zones

(doors, windows, or motion detectors). When a monitored zone is
tripped, the keypad sounds a tone and displays the zone name. This
is an ideal feature for monitoring door zones to tell when someone
comes in or goes out.

You can place any combination of disarmed zones in Zone Monitor
but only the most recent zone tripped is displayed. The displayed
zone name clears automatically after a short time or when the zone
is armed.

Zone Monitor does not function while the system is armed but a zone
placed into it will still be monitored when the system is disarmed.

Using Zone Monitor as part of your weekly system test: After
using the System Test function (see page 16), place all perimeter
and interior zones in Zone Monitor. Starting at the front door, go
around and open and then close each door and window. You should
hear the keypad beep each time. The keypad will also display the
name of each zone as its device is opened.

Once all protected doors and windows have been tested, walk in
front of each motion detector. The keypad should beep to confirm
their operation. If at any time during your weekly testing a device
does not cause the keypad to beep, call the service department for
assistance.

Using the Zone Monitor Function

1. Access the User Menu.

2. Press the COMMAND key until ZONE MONITOR? displays.

3. Press any one of the SELECT keys.
The keypad displays PERIM ALL NBR .

4. Select PERIM to place all disarmed perimeter zones into Zone
Monitor. PERIM is displayed only on All/Perimeter and Home/
Away systems.

4a. The keypad displays PERIM? ADD RMV.
4b. Select ADD to add all perimeter zones to Zone Monitor.
4c. Select RMV to remove all perimeter zones.

5. Select ALL to place all disarmed perimeter and interior zones
into Zone Monitor.

5a. The keypad displays ALL? ADD RMV.
5b. Select ADD to add all disarmed zones to Zone Monitor.
5c. Select RMV to remove all disarmed zones.

6. Select NBR to enter a specific zone number for zone monitor.

7. If NBR is selected, the keypad displays ZONE : - ADD RMV.
7a. Enter any zone number and select ADD to add this zone.
7b. Enter any zone number and select RMV to remove the zone.

8. The zone number automatically disappears and a new zone
number can then be entered in step 7a.

Zone Monitor

User Code Level: Master and Standard.
Function: Allows the system to monitor selected disarmed zones

(doors, windows, or motion detectors). When a monitored zone is
tripped, the keypad sounds a tone and displays the zone name. This
is an ideal feature for monitoring door zones to tell when someone
comes in or goes out.

You can place any combination of disarmed zones in Zone Monitor
but only the most recent zone tripped is displayed. The displayed
zone name clears automatically after a short time or when the zone
is armed.

Zone Monitor does not function while the system is armed but a zone
placed into it will still be monitored when the system is disarmed.

Using the Zone Monitor Function

1. Access the User Menu.

2. Press the COMMAND key until ZONE MONITOR? displays.

3. Press any one of the SELECT keys.
The keypad displays PERIM ALL NBR .

4. Select PERIM to place all disarmed perimeter zones into Zone
Monitor. PERIM is displayed only on All/Perimeter and Home/
Away systems.

4a. The keypad displays PERIM? ADD RMV.
4b. Select ADD to add all perimeter zones to Zone Monitor.
4c. Select RMV to remove all perimeter zones.

16

System Test

User Code Level: Master or Standard.
Function: System Test is used to test the battery, alarm bell or siren,

and communication to a central station. The System Test function
begins automatically as soon as you select it.

Using the System Test Function

1. Access the User Menu.

2. Press the COMMAND key until SYSTEM TEST? displays.

3. Press any one of the SELECT keys. The system test begins
automatically and the keypad displays:

1) BELL SOUNDING during a two second bell test, then:

2) BATTERY - OKAY or BATTERY - TRBL to indicate the

condition of the battery, then:

* 3) TRANSMIT TEST and ATTEMPT NO : 1 during the

transmit test, then:

4) TRANSMIT OKAY or TRANSMIT FAILED to show the

results of the transmit test, then:

5) TEST END to indicate the System Test is complete.

6) You can end the transmit test by pressing the ARROW key.

* The transmit test does not operate on local systems.

Testing your system's burglary protection: The System Test

function should be part of your weekly testing and should be
followed by placing the interior and perimeter burglary devices
in Zone Monitor mode. This allows you to open and then close
each protected door and window while listening for the keypad
to beep confirming its operation. See Zone Monitor.

User Menu

User Codes

User Code Level: Master only.
Function: Allows you to add or delete a user from the system or

change their user code or authority level.
There are three characteristics associated with each user code:

10 3812 Master

User Number - Your system supports 32 users. Each user is

numbered from 1 to 32. This number identifies them to the system
and is transmitted to the central station (if your system is monitored)
when they arm or disarm the system.

User Code - Users also have a 4-digit user code they enter into the
keypad when arming or disarming. This user code is kept secret
from other users and is not transmitted to the central station when
they arm or disarm.

A user enters

only

their user code when operating the system.

Authority Level - The user is also assigned a level of authority
(Master or Standard) by the person administrating the system that
determines the functions they can access.

The table to the right lists system functions users are allowed to
access based on the authority level assigned to their codes at the
time they’re added to the system.

User number User Code

Authority level

System Test

User Code Level: Master or Standard.
Function: System Test is used to test the battery, alarm bell or siren,

and communication to a central station. The System Test function
begins automatically as soon as you select it.

Using the System Test Function

1. Access the User Menu.

2. Press the COMMAND key until SYSTEM TEST? displays.

3. Press any one of the SELECT keys. The system test begins
automatically and the keypad displays:

1) BELL SOUNDING during a two second bell test, then:

2) BATTERY - OKAY or BATTERY - TRBL to indicate the

condition of the battery, then:

User Codes

User Code Level: Master only.
Function: Allows you to add or delete a user from the system or

change their user code or authority level.
There are three characteristics associated with each user code:

10 3812 Master

User Number - Your system supports 32 users. Each user is

numbered from 1 to 32. This number identifies them to the system
and is transmitted to the central station (if your system is monitored)
when they arm or disarm the system.

User Code - Users also have a 4-digit user code they enter into the

User number User Code

Authority level

17

User Codes continued

User Code Authority Levels

System Options Standard Master

Sensor Reset √√
Outputs On/Off √√
Bypass Zones √√
Zone Monitor √√
System Test √√
Arm and Disarm √√
Display Events √√
Schedules √
Date and Time √
User Codes √

Adding User codes:

1. Access the User Menu.

2. Press the COMMAND key until USER CODES? displays.

3. Press any SELECT key. The keypad displays ADD DEL CHG.

4. Press the SELECT key under ADD to add a new user code.
(You must have a Master user level to add a user to the system.)

5. At the USER NUMBER: - prompt, enter a user number and
press COMMAND. The displays changes to CODE NO: .

6. Enter a user code of 4 digits and press COMMAND. This is the
number the user will use each time they arm, disarm, or make
changes to the system.

Note: If your system is using an access control reader, present the

new user's access device instead of entering a user code.

7. The display changes to MASTER? NO YES. Select YES to
make this a Master user level with the authority to access all
User Menu functions.

Select NO to make this a Standard user level. The following
options can then be selected:

7a. TEMP CODE NO YES.

Select NO to make this a permanent user code.
Select YES to make this a temporary code that automatically

expires in 7 days. Temporary codes are ideal for guests or
service technicians. You can delete a Temporary user code
at any time before the 7 day active period ends.

7b. AREAS: . (Displayed in Area systems only).

Enter the area numbers where this user will have access.
For example: if you want this user to only have access to
areas 1 and 2, enter the numbers 1 and 2.

Once the correct area numbers are shown, press Command.

7c. ARM ONLY NO YES.

Select NO to allow this user to arm and disarm the system
and access all Standard level functions in the User Menu.

Select YES to restrict this user to arming only.
(The Arm Only user code can bypass zones not in a normal

condition at the time of arming.)

8. After you've completed making your selections, the keypad
display shows USER # ADDED.

9. Press the ARROW key once to add another user or twice to exit
the User Menu.

User Menu

User Codes continued

User Code Authority Levels

System Options Standard Master

Sensor Reset √√
Outputs On/Off √√
Bypass Zones √√
Zone Monitor √√
System Test √√
Arm and Disarm √√
Display Events √√
Schedules √
Date and Time √
User Codes √

7. The display changes to MASTER? NO YES. Select YES to
make this a Master user level with the authority to access all
User Menu functions.

Select NO to make this a Standard user level. The following
options can then be selected:

7a. TEMP CODE NO YES.

Select NO to make this a permanent user code.
Select YES to make this a temporary code that automatically

expires in 7 days. Temporary codes are ideal for guests or
service technicians. You can delete a Temporary user code
at any time before the 7 day active period ends.

7b. AREAS: . (Displayed in Area systems only).

Enter the area numbers where this user will have access.

18

User Codes continued

Deleting User codes:

1. Access the User Menu.

2. Press the COMMAND key until USER CODES? displays.

3. Press any one of the SELECT keys. The keypad displays ADD
DEL CHG.

4. Press the SELECT key under DEL to delete a user code from
the system. You must have a Master user code level to be able
to delete a user code.

5. At the USER NUMBER: - prompt, enter the user number you
want to delete and press COMMAND. The displays changes to
USER # DELETED.

6. The display then changes back to USER NUMBER: - for you
to delete another user. Press the ARROW key twice to exit the
User Menu.

Ambush Codes

Your system may be programmed to allow user number 1 to be an
Ambush code. The Ambush code functions identically to other
codes with the exception that it sends a silent alarm to the central
station. This silent alarm alerts the operator to a duress situation at
the premises and prompts the immediate notification of the authorities.

Refer to the System Setup section of this guide to see if your system
is programmed for Ambush. If so, do NOT program a code for user
number 1 unless you intend to use the Ambush function.

User Menu

Changing User codes

1. Access the User Menu.

2. Press the COMMAND key until USER CODES? displays.

3. Press any one of the SELECT keys. The keypad displays ADD
DEL CHG.

4. Press the SELECT key under CHG to change a user code. You
must have a Master user code level to change a user code.

5. At the USER NUMBER: - prompt, enter the user number to
change and press COMMAND.

6. The display changes to CODE NO:

* * * *. Enter the new 4-

digit user code and press COMMAND. If the code you entered
is already in use, or is a code used internally by the system, the
keypad displays ALREADY IN USE. You must enter a different
4-digit user code.

7. If you are changing a code other than your own, the keypad next
displays MASTER? NO YES. Select YES if you want this user
to have a Master authority level.

Select NO if you want this user to have a Standard authority level.
If you select NO, refer to item number 7 in the Adding User Codes
section on the previous page.

Important: Changing a user code does not change the user number.
User number two may have their user code changed from 1234 to
5678 but they are still user number two.

User Codes continued

Deleting User codes:

1. Access the User Menu.

2. Press the COMMAND key until USER CODES? displays.

3. Press any one of the SELECT keys. The keypad displays ADD
DEL CHG.

4. Press the SELECT key under DEL to delete a user code from
the system. You must have a Master user code level to be able
to delete a user code.

5. At the USER NUMBER: - prompt, enter the user number you
want to delete and press COMMAND. The displays changes to
USER # DELETED.

6. The display then changes back to USER NUMBER: - for you

Changing User codes

1. Access the User Menu.

2. Press the COMMAND key until USER CODES? displays.

3. Press any one of the SELECT keys. The keypad displays ADD
DEL CHG.

4. Press the SELECT key under CHG to change a user code. You
must have a Master user code level to change a user code.

5. At the USER NUMBER: - prompt, enter the user number to
change and press COMMAND.

6. The display changes to CODE NO:

* * * *. Enter the new

4-digit user code and press COMMAND. If the code you entered
is already in use, or is a code used internally by the system, the
keypad displays ALREADY IN USE. You must enter a different

19

Schedules

User Code Level: Master only.
Function: The Schedules function allows you to program into the

system the times at which you normally turn your burglary protection
on and off each day of the week. This information can then be used
by the system to automatically arm or disarm the burglary protection.

You can also use the Closing Check/Extend feature with Schedules
to help ensure your system is armed by an authorized user at a
specific time. This option sounds the keypad buzzer and displays
CLOSING TIME! when a schedule expires. Users still on the
premises are reminded to arm the system or extend the schedule to
a later time. If the system is not armed, or the schedule not extended,
a report can be sent to the central station and/or a pager.

Your system provides you with two different types of schedules:
Permanent schedules are used for automatic arming and disarming

and always occur at the same time until you change or delete them.
Extend schedules allow an authorized user to extend the present

day's permanent scheduled closing time.

Setting an Arming and Disarming Schedule

1. Access the User Menu.

2. Press the COMMAND key until SCHEDULES? displays. Press
any SELECT key. The keypad displays PRM EXT. Press the
SELECT key under PRM.

3. The keypad next displays the day of the week you want the
schedule to start as SUN MON TUE WED. Press the
COMMAND key to show the remaining days of the week and
then press the SELECT key under your choice.

4. The keypad then displays OP (open) 00:00 PM MON followed
by CL (close) 00:00 PM MON and DELETE KEEP. Press the
SELECT key under DELETE.

The keypad displays OPENING TIME?. Press COMMAND.
The keypad now displays MON – : AM PM. Enter the time
you want the burglary protection to be turned

off

. Use a 12 hour
clock only (00:01 to 11:59). Press the SELECT key under AM
or PM.

5. The keypad then displays CLOSING TIME?. Press the
COMMAND key. The keypad then displays MON – : AM PM.
If you want the schedule to be for consecutive days, press the
SELECT key under MON to increment the days of the week.
When the correct day is shown, enter the time you want the
burglary protection to turn on.

Extended Schedules

Function: This option allows users to extend today's programmed

closing time schedule.

Extending a Closing Schedule

1. Access the User Menu.

2. Press the COMMAND key until SCHEDULES? displays. Press
any SELECT key.

3. The keypad displays PRM EXT. Press the SELECT key under
EXT.

The keypad displays – : AM PM. Enter in the new time for
the closing schedule to expire.

User Menu

Schedules

User Code Level: Master only.
Function: The Schedules function allows you to program into the

system the times at which you normally turn your burglary protection
on and off each day of the week. This information can then be used
by the system to automatically arm or disarm the burglary protection.

You can also use the Closing Check/Extend feature with Schedules
to help ensure your system is armed by an authorized user at a
specific time. This option sounds the keypad buzzer and displays
CLOSING TIME! when a schedule expires. Users still on the
premises are reminded to arm the system or extend the schedule to
a later time. If the system is not armed, or the schedule not extended,
a report can be sent to the central station and/or a pager.

Your system provides you with two different types of schedules:

4. The keypad then displays OP (open) 00:00 PM MON followed
by CL (close) 00:00 PM MON and DELETE KEEP. Press the
SELECT key under DELETE.

The keypad displays OPENING TIME?. Press COMMAND.
The keypad now displays MON – : AM PM. Enter the time
you want the burglary protection to be turned

off

. Use a 12 hour
clock only (00:01 to 11:59). Press the SELECT key under AM
or PM.

5. The keypad then displays CLOSING TIME?. Press the
COMMAND key. The keypad then displays MON – : AM PM.
If you want the schedule to be for consecutive days, press the
SELECT key under MON to increment the days of the week.
When the correct day is shown, enter the time you want the
burglary protection to turn

on

.

20

Date and Time

User Code Level: Master only.

Function: Allows you to change the current date and time displayed
on the keypad and used by the system for schedules and Display
Events.

Setting the Date and Time

1. Access the User Menu.

2. Press COMMAND until TIME? displays.

3. The keypad displays the current day and time. Press the
COMMAND key. The keypad displays the current date. Press
the COMMAND key to make any changes.

4. The keypad displays TIME DAY DATE.

5. Press the SELECT key under TIME to change the time. The
keypad displays – : AM PM. Enter the current time and select
AM or PM.

The display changes back to TIME DAY DATE.

6. Press the SELECT key under DAY to change the day of the
week. The keypad displays SUN MON TUE WED. If the current
day is not displayed, press the COMMAND key. Press the
SELECT key under the correct day.

The display changes back to TIME DAY DATE.

7. Press the SELECT key under DATE to change the date. The
keypad displays:

MONTH: – Enter one or two digits for the month. Press
COMMAND.

DAY: – Enter up to two digits for the day. Press COMMAND.
YEAR: – Enter up to two digits for the year. Press COMMAND.

The display returns to TIME DAY DATE. Press the ARROW
key to exit the User Menu.

User Menu

Date and Time

User Code Level: Master only.

Function: Allows you to change the current date and time displayed
on the keypad and used by the system for schedules and Display
Events.

Setting the Date and Time

1. Access the User Menu.

2. Press COMMAND until TIME? displays.

3. The keypad displays the current day and time. Press the
COMMAND key. The keypad displays the current date. Press
the COMMAND key to make any changes.

4. The keypad displays TIME DAY DATE.

7. Press the SELECT key under DATE to change the date. The
keypad displays:

MONTH: – Enter one or two digits for the month. Press
COMMAND.

DAY: – Enter up to two digits for the day. Press COMMAND.
YEAR: – Enter up to two digits for the year. Press COMMAND.

The display returns to TIME DAY DATE. Press the ARROW
key to exit the User Menu.

21

Display Events

User Code Level: Master or Standard.
Function: Allows you to review up to 100 past events that occurred

on your system from any keypad. Once 100 events are stored, any
new event causes the oldest event to be cleared.

Note: This section shows the User's
Guide Display Events items for both
16-character (single line) and 32­character keypad displays. While in
the Display Events function, use the
COMMAND and ARROW keys to go
forward or backward through the list of
events.

Using the Display Events Function

1. Access the User Menu.

2. Press the COMMAND key until DISPLAY EVENTS? displays.
Press any SELECT key.

3. The keypad displays FIRST LAST. Select FIRST to view
events starting from the oldest to the newest. Select LAST to
view events starting from the newest to the oldest.

If you select FIRST, use the COMMAND key to scroll up through
the events displays.

If you select LAST, use the ARROW key to scroll down through
the event displays.

User Menu

Zone Bypass Event Displays

This displays the bypassing of system zones.

16-Character Display Description

26 BYPS 12 1017 Zone 26 bypassed by user 12. Press the

left

Select key for the zone name and

the

right

Select key for the time.

32-Character Display Description

BYP 5:18P 10 / 17 The east window zone was bypassed.
EAST WINDOW Press a Select key for the zone number

and user number.

Bypass Event Types - There are 4 event types:

BYP - Bypass RST - Restore FRC - Force Arm
FLT - Zone Fault

Note: You may sometimes see the user as SWG or SCH. These are

short for Swinger Bypass and Schedule which are automatic functions
that allow the system to bypass a zone.

Display Events

User Code Level: Master or Standard.
Function: Allows you to review up to 100 past events that occurred

on your system from any keypad. Once 100 events are stored, any
new event causes the oldest event to be cleared.

Note: This section shows the User's
Guide Display Events items for both
16-character (single line) and 32­character keypad displays. While in
the Display Events function, use the
COMMAND and ARROW keys to go
forward or backward through the list of
events.

A BC

D E F

G H I JKL

VW XMNO P Q R ST U

YZ

COMMAND

90

1234
5678

POWER

JONES RESIDENCE
FR I 2 : 51 AM

ARROW key

SELECT keys

COMMAND key

Zone Bypass Event Displays

This displays the bypassing of system zones.

16-Character Display Description

26 BYPS 12 1017 Zone 26 bypassed by user 12. Press the

left

Select key for the zone name and

the

right

Select key for the time.

32-Character Display Description

BYP 5:18P 10 / 17 The east window zone was bypassed.
EAST WINDOW Press a Select key for the zone number

and user number.

A BC

D E F

G H I J KL

VW XMNO P Q R ST U

YZ

COMMAND

90

1234
5678

POWER

JONES RESIDENCE
FR I 2 : 51 AM

ARROW key

SELECT keys

COMMAND key

22

User Menu

Zone Event Displays

This section displays alarms, troubles, and other events that could
occur on your protection zones.

16-Character Display Description

2 BURG ALR 1017 A burglary alarm occurred on zone 2.

Press the

right

Select key for the time the

alarm occurred.

32-Character Display Description

ALR 10: 23P 10/17 An alarm occurred at 10:23

PM on Oct. 17.

BASEMENT DOOR Press any Select key to see the zone

number and zone type.

Zone Type - There are 7 possible zone types you may see here.

FIRE - Fire PANC - Panic BURG - Burglary
EMRG - Emergency SUPV - Supervisory
AUX1 - Auxiliary 1 AUX2 - Auxiliary 2

Event Types - There are 6 event type you may see here:

ALR - Alarm TBL - Trouble RST - Restore
LOW - Low battery MIS - Missing xmitter

Note: LOW and MIS are for wireless systems only.

Arming and Disarming Event Displays

This displays any arming or disarming of system areas.

16-Character Display Description

ARM 3 12 1017 Area 3 has been armed by user 12.

Press the

left

Select key for the area

name. Press the

right

Select key for the

time the arming occurred.

32-Character Display Description

ARM 5:10P 10/ 17 The Perimeter was armed at 5:10

PM.

PERIMETER Press any Select key to display the area

number and user number.

Arming Event Types - There are 2 event type you may see here:

ARM - User armed the system DIS - User disarmed the system

User Checkin Event Displays

This shows when a user selected the pager Checkin feature from
the User Menu. See page 13 for more information.

16-Character Display Description

CHECKIN 16 1017 User 16 selected the Checkin feature on

Oct. 17. Press the

right

Select key for

the Checkin time.

32-Character Display Description

MSG 3: 31P 10 / 17 User 16 selected the Checkin feature
CHECKIN USER: 16 at 3:31 PM on Oct.17.

Zone Event Displays

This section displays alarms, troubles, and other events that could
occur on your protection zones.

16-Character Display Description

2 BURG ALR 1017 A burglary alarm occurred on zone 2.

Press the

right

Select key for the time the

alarm occurred.

32-Character Display Description

ALR 10: 23P 10/17 An alarm occurred at 10:23

PM on Oct. 17.

BASEMENT DOOR Press any Select key to see the zone

number and zone type.

Arming and Disarming Event Displays

This displays any arming or disarming of system areas.

16-Character Display Description

ARM 3 12 1017 Area 3 has been armed by user 12.

Press the

left

Select key for the area

name. Press the

right

Select key for the

time the arming occurred.

32-Character Display Description

ARM 5:10P 10/ 17 The Perimeter was armed at 5:10

PM.

PERIMETER Press any Select key to display the area

number and user number.

Arming Event Types - There are 2 event type you may see here:

23

User Menu

User Code Change Event Displays

This displays any addition, deletion, or change to a user code.

16-Character Display Description

12 ADD 19 1017 User 12 added user 19 on Oct. 17.

Press the

right

Select key for the time

this occurred.

32-Character Display Description

ADD 11: 41A 10 / 17 User 19 added by user 12 at 11:41

AM.

US:19 BY US:12

User Code Event Types - There are 3 event type you may see here:

ADD - User added DEL - User deleted
CHG - User code or authority level has been changed.

Supervisory Event Displays

This displays the date and time of an automatic test report.

16-Character Display Description

AUTO RECALL 1017 The test report was sent on Oct. 17.

32-Character Display Description

MSG 11: 58P 10 / 17 The test report was sent to the central
AUTO RECALL station at the date and time shown.

System Monitor Event Displays

This displays any loss of the system's AC power or battery.

16-Character Display Description

POWER TBL 1017 An AC failure occurred on the system.

Press the

right

Select key for the time.

32-Character Display Description

TBL 1: 05A 10 / 17 An AC failure occurred at 1:05

AM.

AC POWER

System Monitor Event Types - There are 2 event types:

TBL - Trouble RST - Restore

System Monitor Event Names - There are 2 system monitors:

AC POWER BATTERY

SERVICE REQUEST?

This feature of the User Menu allows you to just press any top row
SELECT key while SERVICE REQUEST? is displayed and have the
system automatically send a "Request for Service" message to the
central station. The display changes to REQUEST MADE
momentarily to confirm your request was sent.

Our service department will then contact you to arrange a service
appointment.

Note: This feature is not displayed if it has not been enabled on your
system.

System Monitor Event Displays

This displays any loss of the system's AC power or battery.

16-Character Display Description

POWER TBL 1017 An AC failure occurred on the system.

Press the

right

Select key for the time.

32-Character Display Description

TBL 1: 05A 10 / 17 An AC failure occurred at 1:05

AM.

AC POWER

System Monitor Event Types - There are 2 event types:

TBL - Trouble RST - Restore

System Monitor Event Names - There are 2 system monitors:

User Code Change Event Displays

This displays any addition, deletion, or change to a user code.

16-Character Display Description

12 ADD 19 1017 User 12 added user 19 on Oct. 17.

Press the

right

Select key for the time

this occurred.

32-Character Display Description

ADD 11: 41A 10 / 17 User 19 added by user 12 at 11:41

AM.

US:19 BY US:12

User Code Event Types - There are 3 event type you may see here:

ADD - User added DEL - User deleted

24

System Setup

System Setup

We've provided this System Setup section to allow you to track the
current status of the programmable options on your Security
Command system. If you make changes to the system, you should
update the information contained on these pages.

My system is monitored by a central station.

❏ Yes ❏ No
C/S Name:
Address:
City/State:
Emergency Phone:
Service Phone:
Service Manager:

My system sends Opening and Closing reports.

❏ Yes ❏ No

My system sends Zone Bypass reports.

❏ Yes ❏ No

My system sends Ambush reports.

❏ Yes ❏ No

Protection Areas

Number Description

1
2
3
4

Outputs

Your system has 4 outputs that can be used for various functions.
Below is a list of these outputs and the devices they control.

Output # What it controls

1
2
3
4

Enter the Output number above when using the Outputs On Off User
Menu option to manually toggle the outputs.

User Codes

Your system provides 32 user codes you can program for individual
users. As you add new users or change current users' codes, you
can keep track of their name, user number, and other information
here in this section. Use a pencil to allow for changes.

System Setup

We've provided this System Setup section to allow you to track the
current status of the programmable options on your Security
Command system. If you make changes to the system, you should
update the information contained on these pages.

My system is monitored by a central station.

❏ Yes ❏ No
C/S Name:
Address:
City/State:
Emergency Phone:

Protection Areas

Number Description

1
2
3
4

Outputs

Your system has 4 outputs that can be used for various functions.
Below is a list of these outputs and the devices they control.

Output # What it controls

25

System Setup

User User Name Level Temp Code Areas Arm Only

1MSYN1234YN
2MSYN1234YN
3MSYN1234YN
4MSYN1234YN
5MSYN1234YN
6MSYN1234YN
7MSYN1234YN
8MSYN1234YN

9MSYN1234YN
10 MS Y N 1234 Y N
11 MS Y N 1234 Y N
12 MS Y N 1234 Y N
13 MS Y N 1234 Y N
14 MS Y N 1234 Y N
15 MS Y N 1234 Y N
16 MS Y N 1234 Y N

User Codes

Your system provides 32 user codes you can program for individual users. As you add new users or change current users' codes, you can
keep track of their name, user number, and other information here in this section. Use a pencil to allow for changes.

HOW TO FILL IN THIS TABLE

User - The User Number of the
person authorized to use the
system.

Level - Master or Standard
authority.

Temp Code - Is this code set to
expire after seven days?

HOW TO FILL IN THIS TABLE

User - The User Number of the
person authorized to use the
system.

Level - Master or Standard
authority.

Temp Code - Is this code set to
expire after seven days?

All Areas - Does this user have
the authority to arm and disarm
all areas in the system?

Arm Only - Is this user
restricted to just arming?

Refer to the User Codes section
of this User's Guide for
additional information.

User User Name Level Temp Code Areas Arm Only

1MSYN1234YN

2MSYN1234YN

3MSYN1234YN

4MSYN1234YN

5MSYN1234YN

6MSYN1234YN

7MSYN1234YN

Circle Your Selections

26

User Codes

User Codes

System Setup

HOW TO FILL IN THIS TABLE

User - The User Number of the
person authorized to use the
system.

Level - Master or Standard
authority.

Temp Code - Is this code set to
expire after seven days?

All Areas - Does this user have
the authority to arm and disarm
all areas in the system?

Arm Only - Is this user
restricted to just arming?

Refer to the User Codes section
of this User's Guide for
additional information.

HOW TO FILL IN THIS TABLE

User - The User Number of the
person authorized to use the
system.

Level - Master or Standard
authority.

Temp Code - Is this code set to
expire after seven days?

User User Name Level Temp Code Areas Arm Only

17 MS Y N 1234 Y N
18 MS Y N 1234 Y N
19 MS Y N 1234 Y N
20 MS Y N 1234 Y N
21 MS Y N 1234 Y N
22 MS Y N 1234 Y N
23 MS Y N 1234 Y N
24 MS Y N 1234 Y N
25 MS Y N 1234 Y N
26 MS Y N 1234 Y N
27 MS Y N 1234 Y N
28 MS Y N 1234 Y N
29 MS Y N 1234 Y N
30 MS Y N 1234 Y N
31 MS Y N 1234 Y N
32 MS Y N 1234 Y N

User User Name Level Temp Code Areas Arm Only

17 MS Y N 1234 Y N
18 MS Y N 1234 Y N
19 MS Y N 1234 Y N
20 MS Y N 1234 Y N
21 MS Y N 1234 Y N
22 MS Y N 1234 Y N
23 MS Y N 1234 Y N
24 MS Y N 1234 Y N

Circle Your Selections

27

The relay activates for
five seconds during
which you must open the
door.

Once you open the door,
you have 30 seconds to
exit and close the door
before the zone 2 Soft­Shunt expires.

Easy Entry™ User's Guide

This section of the user's guide provides information on using the Easy Entry™ access control capability of the security command system.
If your system is not currently using any access control devices, disregard this section. Easy Entry™ is built into every Security Command
system and can be accessed using Easy Entry™ keypads.

There are three different operating modes: Door Strike, Arming and Disarming, and Entry Delay. All of the examples below assume that your
system requires a user code to arm and disarm the protection.

DOOR STRIKE

Area and All/Perimeter Door Strike - From the Status List, present

your card to the reader. Once it is validated by the system, the Door
Strike relay activates. See Door Strike Relay Operation above.
Home/Away systems only activate the Door Strike relay when arming
and disarming.

Select NO to arm or disarm
individual areas. Select YES,
or simply wait, and the
keypad will automatically
arm or disarm all areas for
which you are authorized.

ARMING AND DISARMING AN AREA SYSTEM

Press Command. The keypad displays ARM DISARM.
Press the Select key under either option. The keypad
displays ENTER CODE: -. Present your card to the
reader. Once it is validated by the system, all areas
accessible by you arm or disarm automatically and the
Door Strike relay activates.

Appendix

The relay activates for
five seconds during
which you must open the
door.

Once you open the door,
you have 30 seconds to
exit and close the door
before the zone 2 Soft­Shunt expires.

Easy Entry™ User's Guide

This section of the user's guide provides information on using the Easy Entry™ access control capability of the security command system.
If your system is not currently using any access control devices, disregard this section. Easy Entry™ is built into every Security Command
system and can be accessed using Easy Entry™ keypads.

There are three different operating modes: Door Strike, Arming and Disarming, and Entry Delay. All of the examples below assume that your
system requires a user code to arm and disarm the protection.

DOOR STRIKE

Area and All/Perimeter Door Strike - From the Status List, present

your card to the reader. Once it is validated by the system, the Door
Strike relay activates. See Door Strike Relay Operation above.
Home/Away systems only activate the Door Strike relay when arming
and disarming.

ABC SECURITY
FRI 2:51 AM

POWER

While the keypad is in
the Status List, present
your access card.

ABC SECURITY
ARM DISARM

ABC SECURITY
ENTER CODE: –

ABC SECURITY
ALL? NO YES

POWER POWER POWER

ABC SECURITY
FRI 2:51 AM

POWER

While the keypad is in
the Status List, present

28

ARMING AND DISARMING AN ALL/PERIMETER SYSTEM

Press Command. The keypad displays PERIM ALL (when arming) or DISARM?.
Press the Select key under the option. The keypad displays ENTER CODE: -.

Present your card to the reader. Once it is validated by the system, both areas arm
or disarm automatically and the Door Strike relay activates.

ARMING AND DISARMING A HOME/AWAY SYSTEM

Home/Away system Arming and Disarming - Present your card to the reader. If the system

is armed, once the card is validated all areas are disarmed.
If the system is disarmed when you present your card, once it is validated all areas are armed

in the AWAY mode.

The system arms or
disarms the areas
and activates the
Door Strike relay.

ENTRY DELAY

All Systems - Once the protected door is opened and the entry delay

starts, the keypad displays ENTER CODE: -. Present your card to the
reader and, once it is validated, the system disarms all areas accessible
by you and activates the Door Strike relay. Area systems provide a
delay to allow selected areas only to be disarmed. See Arming and
Disarming above.

Using the access reader for user menu access

You can also use a card reader to access the User Menu when the

MENU? NO YES display is shown.

The system disarms the areas and activates the Door
Strike relay. Area systems allow a delay for you to
select only certain areas. See Arming and Disarming.

Appendix

ARMING AND DISARMING AN ALL/PERIMETER SYSTEM

Press Command. The keypad displays PERIM ALL (when arming) or DISARM?.
Press the Select key under the option. The keypad displays ENTER CODE: -.

Present your card to the reader. Once it is validated by the system, both areas arm
or disarm automatically and the Door Strike relay activates.

ARMING AND DISARMING A HOME/AWAY SYSTEM

Home/Away system Arming and Disarming - Present your card to the reader. If the system

is armed, once the card is validated all areas are disarmed.
If the system is disarmed when you present your card, once it is validated all areas are armed

in the AWAY mode.

The system arms or
disarms the areas
and activates the
Door Strike relay.

POWER

ABC SECURITY
ENTER CODE: -

Access door is

opened.

POWER

PERIM ALL

DISARM?

or

POWER

ABC SECURITY
FRI 2:51 AM

POWER

ABC SECURITY
FRI 2:51 AM

POWER

PERIM ALL

DISARM?

or

POWER

29

Pager Direct™

Security Command Alphanumeric Paging

Area Names

Security Command Numeric Paging

Area Names

Pager Direct™ User's Guide

Pager Direct uses the reporting capability of your security system to dial your pager number and send reports in much the same way as
someone sending you a pager message would do. You can receive reports of alarms, troubles, or armings and disarmings of the system
and know at a glance the status of your system.

Appendix

Cut along dotted lines

Cut along dotted lines

Fold

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Area Names

Area Names

Pager Direct™ User's Guide

Pager Direct uses the reporting capability of your security system to dial your pager number and send reports in much the same way as
someone sending you a pager message would do. You can receive reports of alarms, troubles, or armings and disarmings of the system
and know at a glance the status of your system.

List your system's area names and numbers below:

Area Name Area Name

1_______________________ 3 ______________________

2_______________________ 4 ______________________

Service Department Phone: ______________________
Emergency Phone: _____________________________

Pager Direct™

List your system's area names and numbers below:

Area Name Area Name

1_______________________ 3 ______________________

2_______________________ 4 ______________________

Service Department Phone: ______________________
Emergency Phone: _____________________________

Central Station Phone: ____________________________

List your system's area names and numbers below:

Area Name Area Name

1_______________________ 3 ______________________

2_______________________ 4 ______________________

Service Department Phone: ______________________
Emergency Phone: _____________________________

Central Station Phone: ____________________________

List your system's area names and numbers below:

Area Name Area Name

1_______________________ 3 ______________________

2_______________________ 4 ______________________

Service Department Phone: ______________________
Emergency Phone: _____________________________

30

Account Number

Security Command Numeric Paging

Numeric Pager Display

This number has been programmed into your Security Command system
as an identifier. Whenever the system sends a message to your pager, it
will always send the account number first to identify itself.

Message ID

This is always a single digit, 1 to 6, that describes the message sent.

1 = Zone Alarm 3 = Area(s) Arming
2 = Zone Trouble 4 = Area(s) Disarming 6 = User Checkin

Zone, Area, or User Number

If this message is for a zone, the 1 to 2 digit zone number is displayed.
If this message is for areas that are being armed or disarmed, the area

numbers are shown in sequential order. Example: 1 2 4.

00128–301234

Account

Number

MessageIDAlways

Zero

Zone, Area, or

User Number

Appendix

Account Number

Numeric Pager Display

This number has been programmed into your Security Command system
as an identifier. Whenever the system sends a message to your pager, it

00128–301234

Account

Number

MessageIDAlways

Zero

Zone, Area, or

User Number

Security Command Alphanumeric Paging

Account Number

Whenever the system sends a message to your pager, it will always send
the account number first to identify itself. After the account, you'll see:

Typical Zone Event Display Description

20002 001 NORTHWEST DOORS BURG *ALARM* SHIPPING

Account Zone Zone Name Zone Type Event Area Name

Zone Types - BURG, FIRE, SUPV (Supervisory), PANC (Panic), EMRG (Emergency), AUX1, or AUX2
Events - ALARM or TROUBLE

Typical Arming/Disarming Display Description

20002 ARMED 0016 01 EAST WAREHOUSE

Account Event User # Area # Area Name

Events - ARMED or DISARMED

User Checkin Display Description

20002 USER CHECKIN REPORT BY 0016

Account Function Performed User #

Functions - USER CHECKIN REPORT (An authorized user has selected Checkin from the User Menu)

Typical System Event Display Description

20002 LATE TO CLOSE

Account Event

Events - LATE TO CLOSE (The system has not been armed at its scheduled closing time)

ALARM CANCELLED (An alarm has been cancelled by an authorized user)

Account Number

Whenever the system sends a message to your pager, it will always send
the account number first to identify itself. After the account, you'll see:

Typical Zone Event Display Description

20002 001 NORTHWEST DOORS BURG *ALARM* SHIPPING

Account Zone Zone Name Zone Type Event Area Name

Zone Types - BURG, FIRE, SUPV (Supervisory), PANC (Panic), EMRG (Emergency), AUX1, or AUX2
Events - ALARM or TROUBLE

Typical Arming/Disarming Display Description

20002 ARMED 0016 01 EAST WAREHOUSE

Account Event User # Area # Area Name

31

PhoneAccess™ Quick Commands

PhoneAccess™ User's Guide

This exciting feature allows you to call your XR20 system from any outside touchtone phone to arm and disarm protection areas or turn on
or off the panel's relay outputs.

How it works

1. From a touchtone phone, call the XR20 system's phone number.

2. The XR20 answers the call and sounds a short ready tone. You
now have 8 seconds to enter a valid

Master

user code. If the user
code is accepted by the panel, you'll hear one or more beeps giving
you the current armed status of the system. (You can also find out
the armed status of the system by pressing the * key at any time.)

If You'll hear

All areas are armed 3 short beeps
Area 1 (Perimeter) is armed 1 short beep
Any area is armed 2 short beeps
All areas are disarmed 1 long beep

If the user code is

not

accepted by the panel, you'll hear four short
beeps. Check the user code and try again. After 3 unsuccessful
attempts to enter the code, the panel locks out PhoneAccess™ until
a valid user code is entered at a keypad on the XR20 system.

3. Once the user code is accepted by the panel and the armed status
is given, you can enter the following commands:

Press To do this You'll hear

#, 1 Arm all areas 3 short beeps
#, 2 Arm area 1 1 short beep
#, 3 Arm areas 1 & 2 2 short beeps
#, 0 Disarm all areas* 1 long beep
#, 5, 4, 0, n* Toggles the output 1 short beep = on

1 long beep = off
4 short beeps = restricted

Note: Zones in a bad condition are force armed when the area arms.

Cut along dotted lines

(* Use outputs 1, 2, 3, or 4 in place of n)

Press To do this You'll hear

# then 1 Arm all areas 3 short beeps
# then 2 Arm area 1 1 short beep
# then 3 Arm areas 1 & 2 2 short beeps

Note: Zones in a bad condition are force armed when the area arms.

# then 0 Disarm all areas 1 long beep
#, 5, 4, 0, n* Toggles the output 1 short beep = on

1 long beep = off
4 short beeps = restricted

1. _________________________ 3. _________________________

2. _________________________ 4. _________________________

(* Use outputs 1, 2, 3, or 4 in place of n)

Quick Reference Wallet Card

PhoneAccess™ User's Guide

This exciting feature allows you to call your XR20 system from any outside touchtone phone to arm and disarm protection areas or turn on
or off the panel's relay outputs.

How it works

1. From a touchtone phone, call the XR20 system's phone number.

2. The XR20 answers the call and sounds a short ready tone. You
now have 8 seconds to enter a valid

Master

user code. If the user
code is accepted by the panel, you'll hear one or more beeps giving
you the current armed status of the system. (You can also find out
the armed status of the system by pressing the * key at any time.)

If You'll hear

All areas are armed 3 short beeps
Area 1 (Perimeter) is armed 1 short beep
Any area is armed 2 short beeps
All areas are disarmed 1 long beep

Quick Reference Wallet Card

(Enter output descriptions below)

PhoneAccess™ Quick Commands

Press To do this You'll hear

# then 1 Arm all areas 3 short beeps
# then 2 Arm area 1 1 short beep
# then 3 Arm areas 1 & 2 2 short beeps

Note: Zones in a bad condition are force armed when the area arms.

# then 0 Disarm all areas 1 long beep
#, 5, 4, 0, n* Toggles the output 1 short beep = on

1 long beep = off
4 short beeps = restricted

1. _________________________ 3. _________________________

2. _________________________ 4. _________________________

(* Use outputs 1, 2, 3, or 4 in place of n)

(Enter output descriptions below)

PhoneAccess™ Quick Commands

Press To do this You'll hear

# then 1 Arm all areas 3 short beeps
# then 2 Arm area 1 1 short beep
# then 3 Arm areas 1 & 2 2 short beeps

Note: Zones in a bad condition are force armed when the area arms.

# then 0 Disarm all areas 1 long beep
#, 5, 4, 0, n* Toggles the output 1 short beep = on

1 long beep = off
4 short beeps = restricted

1. _________________________ 3. _________________________

(* Use outputs 1, 2, 3, or 4 in place of n)

(Enter output descriptions below)

Appendix

32

1. Call the panel phone number. The panel answers and sounds one
short tone.

2. Enter your code within 8 seconds. One beep means the code is
good. Four short beeps means enter it again. You have 3 tries.

3. You have 30 seconds to enter the first command (see other side)
and 30 seconds for each additional command.

If You'll hear

All areas are armed 3 short beeps
Area 1 (Perim) is armed 1 short beep
Any area is armed 2 short beeps

1. Call the panel phone number. The panel answers and sounds one
short tone.

2. Enter your code within 8 seconds. One beep means the code is
good. Four short beeps means enter it again. You have 3 tries.

3. You have 30 seconds to enter the first command (see other side)
and 30 seconds for each additional command.

If You'll hear

All areas are armed 3 short beeps
Area 1 (Perim) is armed 1 short beep
Any area is armed 2 short beeps
All areas are disarmed 1 long beep

1. Call the panel phone number. The panel answers and sounds one
short tone.

2. Enter your code within 8 seconds. One beep means the code is
good. Four short beeps means enter it again. You have 3 tries.

3. You have 30 seconds to enter the first command (see other side)
and 30 seconds for each additional command.

If You'll hear

All areas are armed 3 short beeps
Area 1 (Perim) is armed 1 short beep
Any area is armed 2 short beeps
All areas are disarmed 1 long beep

Appendix

33

FA113 User's Guide

These instructions guide you through the operation of the XR20 Command Processor system using the FA113 Wireless Keychain
Remote. The FA113 uses the audible output capability of the Security Command keypad to sound confirmation tones. It is
recommended that you use the FA113 within hearing distance of these keypads.

Arming a Home/Away or All/Perimeter System

1. Press the ON button once to arm the Perimeter burglary protection. The Security Command keypads emit a single beep to
confirm the arming. The Perimeter arms and all non-priority zones not in a normal condition are force armed.

2. After the single beep, press the ON button a second time to arm the Interior burglary protection. The Security Command keypads
emit two beeps to confirm the arming.

3. After the two beeps, pressing the ON button in Home/Sleep/Away systems arms the Bedrooms burglary protection. The Security
Command keypads emit three beeps to confirm the arming.

Disarming a Home/Away or All/Perimeter System

1. Press the OFF button once. The Security Command keypads emit a single 2-second beep to confirm the disarming.

Arming an Area System

1. Press the ON button once to arm the following areas:

1. ___________________ 2. ___________________ 3. ___________________ 4. ___________________

The Security Command keypads emit a single beep to confirm the arming.

Disarming an Area System

1. Press the OFF button once to disarm the above areas. The keypads emit a single beep to confirm the disarming.

Using the ALERT Buttons

Pressing the two ALERT buttons simultaneously sends a Panic alarm to the panel. If your system is monitored by a central station,
the proper authorities will be notified of the alarm.

FA113 User's Guide

These instructions guide you through the operation of the XR20 Command Processor system using the FA113 Wireless Keychain
Remote. The FA113 uses the audible output capability of the Security Command keypad to sound confirmation tones. It is
recommended that you use the FA113 within hearing distance of these keypads.

Arming a Home/Away or All/Perimeter System

1. Press the ON button once to arm the Perimeter burglary protection. The Security Command keypads emit a single beep to
confirm the arming. The Perimeter arms and all non-priority zones not in a normal condition are force armed.

2. After the single beep, press the ON button a second time to arm the Interior burglary protection. The Security Command keypads
emit two beeps to confirm the arming.

3. After the two beeps, pressing the ON button in Home/Sleep/Away systems arms the Bedrooms burglary protection. The Security
Command keypads emit three beeps to confirm the arming.

Disarming a Home/Away or All/Perimeter System

Appendix

Alarm displays

how long in display 5
Ambush codes 18
Arming

All/Perimeter mode 9, 28

Area mode 7, 27

Home/Away mode 11, 28

Instant mode 9, 11

through the telephone 31

using Easy Entry™ 27

with doors and windows open 6
BAD display 6
Bypassing a zone 14

restoring a bypassed zone 14

zones that can't be bypassed 14
Checkin reports to pager 13
CLOSING TIME! display 19
DIALING display 6
Disarming, 1, 4

alarm display 8, 10,

clears alarm displays 5

during an alarm 10, 12

Easy Entry™ keypads 27

Easy Exit™ feature 12

ENTER CODE display 3, 8, 10 12

keypad display 8, 10

only selected areas 8

prewarn tone 8, 10, 12

reporting to central station 8, 10, 12

Door Strike operation 27

after Sensor Reset 13
Easy Entry™ 13, 27
Easy Exit™ feature 12
Emergency procedures ii
Entry and Exit zones 4
Events held in memory

amount 21
Exit Error 5
Extending a schedule 19
False Alarms 1
Keypad messages 3

ALARM CANCELLED 10

ALREADY IN USE 18

BAD * 6

CLOSING TIME! 19

DIALING ... 6

INSTNT 11

LOCAL ALARM ONLY 6
Keypad operation 2
Keypad tones

during a trouble condition 3

entering while armed 3

Zone Monitor tone 3
Keyswitch operation

exit delay display 6

user number zero 22
Monitoring zones 15
Outputs

names and numbers 14
turning on and off 14, 33

Pager reporting 29

quick reference card 29

Panic

alarms not displayed 5

Perimeter protection 4

arming 9, 11
Power (AC) LED 2
Priority zone

BAD * condition 6
Relay control 14
Resetting a smoke detector 13
Security Command keypad 1-2
Sending reports to a Central station 5, 10
Sending reports to your pager 29
Sensor Reset 13

before using 13

for wireless systems 13
Silent alarm 18
System Setup 24
System status 5

Panic zone alarms 5
Testing the system 1, 15, 16
Turning the system off, see Disarming
Turning the system on, see Arming
User Checkin 13
User Codes 16

Ambush codes 18

Index

area restrictions 17
arming only 17
authority level 16-17
deleting 18
Master codes 17
Temporary codes 17
user number 16

User Menu 1

accessing 13, 28
restrictions 17

Using Schedules 19

automatic arming 19
automatic disarming 19

Using the keypad 2

arrow key 2
command key 2
top row keys 2

Viewing past events 21

arming and disarming 22
system troubles 23
user code changes 23
zone alarms and troubles 22

Wireless

Keychain Remote 33
low battery displays 13

Zones 4

24 hour zones 4
bypassing 6

Zone Monitor 15

for testing the system 15

Index

Alarm displays

how long in display 5
Ambush codes 18
Arming

All/Perimeter mode 9, 28

Area mode 7, 27

Home/Away mode 11, 28

Instant mode 9, 11

through the telephone 31

using Easy Entry™ 27

with doors and windows open 6
BAD display 6
Bypassing a zone 14

Door Strike operation 27

after Sensor Reset 13
Easy Entry™ 13, 27
Easy Exit™ feature 12
Emergency procedures ii
Entry and Exit zones 4
Events held in memory

amount 21
Exit Error 5
Extending a schedule 19
False Alarms 1
Keypad messages 3

ALARM CANCELLED 10

names and numbers 14
turning on and off 14, 33

Pager reporting 29

quick reference card 29

Panic

alarms not displayed 5

Perimeter protection 4

arming 9, 11
Power (AC) LED 2
Priority zone

BAD * condition 6
Relay control 14
Resetting a smoke detector 13
Security Command keypad 1-2

area restrictions 17
arming only 17
authority level 16-17
deleting 18
Master codes 17
Temporary codes 17
user number 16

User Menu 1

accessing 13, 28
restrictions 17

Using Schedules 19

automatic arming 19
automatic disarming 19

LT-0303 (5/97)