Security Cameras Direct ECO4IR, ECO4LCD Quick Installation And Setup Manual

4-Camera H.264 Day/Night Security System Quick Installation and Setup Guide

Products: ECO4IR, ECO4LCD

ECO4LCD System

PLEASE READ THIS MANUAL BEFORE USING YOUR SYSTEM, and always follow the instructions for safety and proper use. Save this manual for future reference.

ECO4_SQ

www.SecurityCamerasDirect.com

CAUTION



Do not expose this appliance to rain or moisture. Operate this device only in environments where the temperature or humidity is within the recommended range. Operation at extreme temperatures or in very high or low humidity levels may cause electric shock and shorten the life of the product.

CAUTION



FCC Caution: To assure continued compliance, use only shielded interface cables when connecting to computer or peripheral devices. Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

NOTE

This equipment has been tested and found to comply with the limits for a Class “A” digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

LEGAL NOTICE

Security Cameras Direct products are designed to meet safety and performance standards with the use of specic Security Cameras Direct authorized accessories. Security Cameras Direct disclaims liability associated with the use of non-Security Cameras Direct authorized accessories.

The recording, transmission, or broadcast of any person’s voice without their consent or a court order is strictly prohibited by law.

Security Cameras Direct makes no representations concerning the legality of certain product applications such as the making, transmission, or recording of video and/or audio signals of others without their knowledge and/or consent. We encourage you to check and comply with all applicable local, state, and federal laws and regulations before engaging in any form of surveillance or any transmission of radio frequencies.

Microsof t, Windows, and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Android is a trademark of Google Inc. Use of this trademark is subject to Google Permissions. Apple, iPhone, iPod touch, and iPad are registered trademarks of Apple Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Security Cameras Direct disclaims any proprietary interest in trademarks and trade names other than its own.

No part of this document may be reproduced or distributed in any form or by any means without the express written permission of Security Cameras Direct.

Security Cameras Direct 1 Security Cameras Direct Way, Luling, TX 78648 Sales/Support: 1.800.316.6027 | Fax: 1.830.875.9010

iii4-Camera H.264 Security System Setup Guide

SAFETY INSTRUCTIONS

Safety Instructions

Read these instructions and keep them in a safe place for future reference.

• Please refer all work related to the installation of this product to qualied service personnel or system installers.

• Do not operate the appliance beyond its specied temperature, humidity or power source ratings.

• Place the unit on a at surface not prone to vibration or impact.

• Use the appliance at temperatures between 32°F ~ 113°F (0°C ~ +45°C) and humidity below 85%. The input power source

for this appliance is between 90 ~ 264 VAC, 47 ~ 63 Hz.

• Install the unit away from heat sources such as radiators, heat registers and stoves.

• Installation of the unit near consumer electronics devices, such as stereo receiver/ampliers and televisions, is permitted as long

as the air surrounding the terminal does not exceed the above mentioned temperature range.

• Handle hard disk drives with care. — It is possible to damage hard drives if they are moved while their motors are still running. To allow the hard drive to spin

down and park its heads, wait at least 10 seconds after disconnecting power before moving the unit.

— To avoid shock and vibration damage to the internal hard drive, do not move the unit while it is plugged in. — Protect hard disk drives from static electricity. — Do not stack hard disk drives or keep them upright. — Do not use an electric or magnetic screwdriver to x hard disk drives.

• Do not place the unit in an enclosed area where the cooling vents are blocked or impede the ow of air through the ventilation

openings.

• Protect the power cord from being stepped on or pinched particularly at plugs and the points where they exit from the

apparatus.

• Do not drop metallic parts through slots. This could permanently damage the appliance. Turn the power o immediately and

contact qualied service personnel for service.

• Handle the appliance with care. Do not drop or shake, as this may damage the device.

• Do not expose the appliance to water or moisture, nor try to operate it in wet areas. Do not install the unit in an area where

condensation occurs. Do not operate with wet hands. Take immediate action if the appliance becomes wet. Turn the power o and refer servicing to qualied service personnel. Moisture may damage the appliance and also cause electric shock.

• Do not use strong or abrasive detergents when cleaning the surfaces of this product. When dirt is hard to remove, use a mild

detergent and wipe gently.

• Do not overload outlets and extension cords. Electric shock or re may result.

• Save your system conguration.

• Distributing, copying, disassembling, reverse compiling, reverse engineering, and exporting, in violation of export laws, the

software provided with this product is expressly prohibited.

www.SecurityCamerasDirect.com

TABLE OF CONTENTS

Table of Contents

SECTION 1 Systems Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1 Controls, connectors and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SECTION 2 Installing the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Getting Started: Unpacking the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Camera installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2.2.1 Camera placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

2.2.2 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Install and setup a monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

2.4 DVR installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

2.4.1 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

2.5 Connecting the components together . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

2.6 Adjusting the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

SECTION 3 System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.1 Login to the DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

3.2 Conguring the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

3.2.1 Setting the screen language and video system format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

3.2.1 Setting the system time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

3.2.2 Change the Admin and user1 passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

3.2.3 Add uses to the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

3.2.4 Set HDD overwrite option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

3.3 Record conguration settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

3.4 Video conguration settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

3.4.1 Video setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

3.5 Network conguration settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

3.6 Alarm conguration settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

3.6.1 Motion detection setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

SECTION 4 Networking Your DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

4.1 Congure the DVR for access on your home network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

4.1.1 Verify local network connectability with IE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

4.2 Accessing your DVR from the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

SECTION 5 Accessing Your DVR With a Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

5.1 Connecting to your DVR with IE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

5.2 Live screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

v4-Camera H.264 Security System Setup Guide

TABLE OF CONTENTS

5.3 Replay window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

5.4 Remote window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

5.5 Local setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

5.6 Logout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

5.7 Accessing the DVR with Mozilla® Firefox® or Google Chrome™ browsers . . . . . . . . . . . . . . . . . . . . .47

SECTION 6 KWeye Smartphone App . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

6.1 Installing KWeye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

6.1.1 Installing KWeye in iPhone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

6.1.2 Installing KWeye in Android . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

6.2 Set up access to a DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

6.3 Using KWeye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

SECTION 7 DVR System Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

7.1 Menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

7.1.1 Tool Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

7.1.2 Menu options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

7.2 System menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

7.2.1 Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

7.2.2 Video System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

7.2.3 Time Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

7.2.4 User management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

7.2.5 HDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

7.2.6 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

7.2.7 Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

7.3 Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

7.3.1 Record Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

7.3.2 Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

7.3.3 Bit-rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

7.3.4 Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

7.3.5 Frame Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

7.3.6 Packtime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

7.3.7 Record Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

7.4 Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

7.4.1 Video Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

7.4.2 Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

7.4.3 Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

7.4.4 Live . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

www.SecurityCamerasDirect.com

TABLE OF CONTENTS

7.4.5 Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

7.4.6 Record Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

7.4.7 Margin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

7.4.8 Video Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

7.5 Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

7.5.1 Network Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

7.5.2 DDNS Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

7.5.3 Email Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

7.5.4 Mobile Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

7.6 Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

7.6.1 DURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

7.6.2 BUZZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

7.6.3 PRERECORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

7.6.4 EXCEPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

7.6.5 Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

SECTION 8 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

APPENDIX A O-loaded Video Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

APPENDIX B Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

14-Camera H.264 Security System Setup Guide

SECTION 1: SYSTEM OVERVIEW

SECTION1

Systems Overview

Congratulations on purchasing your 4-Camera H.264 Security System! Your system includes:

• 4–camera networkable digital video recorder (DVR) with a pre-installed 500 GB hard drive.

• Local conguration and control using the operator control panel and mouse, or remote access and control through the

Microsoft® Internet Explorer® (IE) browse.

• State-of-the-art H.264 compression technology to maximize your recording time, optimize your video quality, and minimize

hard drive space. Data stored in the DVR can easily be o-loaded via USB or across your network.

• Apple® iPhone®, iPad®, and iPod Touch®, Google Android™, Symbian™, Windows® Mobile, and Blackberry® smartphones apps

that let you monitor your home or business on the go from almost anywhere.

• LCD 17” monitor (with ECO4LCD systems only)

Cameras

5-way Splitter

Mouse

Remote Control

Video/Power Extension Cables

DVR

Power Adapter

ECO4IR system components

www.SecurityCamerasDirect.com

1.1 Controls, connectors and indicators

Your new security system is easy to use and easy to setup. This section includes the function and use of the components included with a ECO4IR system. For installation instructions, refer to Section 2. System setup, including advanced control and conguration procedures, is included in Section 3.

DVR Front Panel

Single/Multi Camera Display Select

tqpu Menu

Navigation Buttons

MenuLED Indicator|

Panel

Enter

Video Playback Controls

Infrared

Sensor

Power/ Record

Button Usage

Selec t any single camera channel (channel 1, 2, 3, or 4 )to display, or sele ct the 4-channel display.

Infrared Sensor Sensor for the remote control.

Enter Press to conrm a menu cho ice.

t q p u

Use arrow but tons to move among the menu i tems. Press Enter ( 8 ) to conrm your choice. Use these button s to navigate through

the menu s ystem. Generally, use t he

t u buttons to move to sele ction boxes, and use q p to sele ct submenu parameters.

POWER/REC Use to power on the DV R, and start and stop manual recording.

Video Playbac k Controls

Standard controls for p laying back a selected video track.

u/II: Op ens video search and playback m enu. When the play back mode

is activate d, press this button to play/pause playb ack.

MENU Opens t he main menu window

USB

Side panel USB 2.0 port (s ee below). This por t can be used for a por table mobile HDD, ash dr ive, DVD burner, rmware upgrade, etc. Note: Conne ct the mouse to the USB port o n the back panel.

Side Panel

USB Port

SECTION 1: SYSTEM OVERVIEW

34-Camera H.264 Security System Setup Guide

SECTION 1: SYSTEM OVERVIEW

DVR Backpanel

CH1 - CH4

Video In

LAN

Monitor Out

(BNC)

Monitor Out

(VGA)

USB

Power

DC 12V

Connector Usage

DC 12V Connec t to 12 VDC power adapter.

Monitor Out (VGA) Standard VGA out put to a display device, suc h as a computer monitor.

Monitor Out (BNC) BNC composite video output to display device (75Ω, 1V p-p)

CH1 .. CH4 VIDEO IN BNC video inpu t to video channels 1, 2, 3, and 4.

LAN Standard RJ-45 Ethernet 10/100BaseT port with au to detect.

USB Use this USB por t to connect a mouse, or a b ackup device such as a ash drive or DVD reco rder.

Remote control

The enter key on the remote control or the front panel has the same function as a mouse left click. The IR Range of the remote control is 10 meters. The buttons on the remote control correspond with the buttons on the front panel.

2 31

75 64

111213 10

Item Function

1 Stop: Stop p layback

2 Play/Pause: Opens video search and playbac k menu. In playbac k mode, press this but ton to play/pause playbac k.

t q p u Move selected item in menu.

4 ENTER: This but ton is used as the “enter” key for most op erations.

www.SecurityCamerasDirect.com

SECTION 1: SYSTEM OVERVIEW

Item Function

5 Menu (MENU/ESC): Displays/exits th e main menu.

6 Lock: If the p assword is enabled, press it to logout the system.

7 Numer ical Button: Use buttons 1, 2, 3, or 4 to select the channel to display.

8 REC: Start or Stop manual recording.

9 Quad: Press this but ton to switch display modes f rom single chann el display to a multi-channel display.

10 Mute: Not used.

11 Spot View: Press to enable auto s equencing.

12 Fast For ward: Fast for ward video during playback.

13 Rewind: Rewind vide o during playback.

Mouse control

The mouse operates just like a mouse on a Windows PC. Connect the mouse to the USB connector in the back panel.

Action Eect

Right click

In live display mod e, right clicking to either display or hid e the tool bar.

In main menu or sub menu mode, r ight clicking to exit the cur rent menu. Note that the sett ings will not be saved af ter right clic king.

Left click

On menu unlock mo de, in the tool bar lef t click on the SYSTEM SETTINGS icon to enter into the main menu.

After entering main menu, lef t clicking to enter sub menus.

In menu mode, lef t click to play one recording le.

Left click to s elect value s in edit boxes or pull-down menus. The system supp orts special sy mbols, number s and letter s.

In the playback mode, left click to control t he >> forward function, << reverse function, >>I Slow play function, I> fr ame play function, > Play function, and X exit funct ion.

You can lef t click to adjus t color control b ar and screen control b ar.

In the main menu, sub menu or playback view, lef t click “x” to e xit/close the current menu.

Left click to c hange the sele ct/desele ct a check box in the mot ion detect ion menu.

Double click In live view or during video playback, double-click to maximize channel on the screen.

Mouse drag

In the Motion De tection se tting inter face, lef t click to drag a fr ame to set the mot ion detect ion area.

Use the mouse to s elect menu items.

CFC6044IR cameras

The CFC6044IR cameras have no controls and indicators, but do include installation features.

54-Camera H.264 Security System Setup Guide

SECTION 1: SYSTEM OVERVIEW

Adjustable Sun Shield

Lens

Mounting

Bracket

Assembly

Camera Assembly with Mounting Bracket

IR Array

Light Level Sensor

Directional Adjustment Set Screw

Camera Mounting Thumb Screw

CFC6044IR camera (drop cable not shown)

The camera drop cable includes two connectors, a BNC connector for the video signal, and a power connector.

www.SecurityCamerasDirect.com

SECTION 2: INSTALLING YOUR SYSTEM

SECTION2

Installing the System

2.1 Getting Started: Unpacking the Equipment

Your system includes:

• 4 channel H.264 networkable DVR

• 4 Cameras

• 4 – 60’ video/power extension cables

• Power adapter and 5-way splitter

• Remote control and USB mouse

• Monitor (with ECO4LCD only)

• Quick-start reference guide (this document)

• Resource Pack Mini-CD with user guides for the DVR, cameras, smartphone applications

Remove the equipment from its packaging and place it on a at, clean surface. Inspect each item. If any visible damage is present, contact your supplier or Security Cameras Direct for a replacement. Verify that your order is complete.

What you need

Although each security system installation is dierent, most require the following items not included with your system components:

• Tools to install the cameras and route power and video cables

• Fasteners to attach the cameras to the mounting surfaces

• A display device and cabling to connect to the DVR (ECO4IR system only). The DVR will connect directly to a VGA video

monitor, or to a TV with a BNC to RCA adapter and RCA cable. The display device is usually needed only for system setup. It can be disconnected when the DVR is networked for access across a LAN or Internet.

• Uninterruptible power supply (UPS). This device is used to ensure system stability during voltage surges, sags, and outages. If a

UPS is not available, a power strip with strong surge protection is highly recommended.

2.2 Camera installation

Your CFC6044IR camera is a precision instrument that will provide years of quality service when used properly. Included with each camera is:

• An adjustable mounting bracket that is attached to the back of the camera.

• 60’ video and power extension cable

74-Camera H.264 Security System Setup Guide

SECTION 2: INSTALLING YOUR SYSTEM

2.2.1 Cameraplacement

Plan your camera installation carefully. Identify the locations where cameras will provide the best coverage, considering:

• Field of view – Cameras should be positioned so they can eectively view the entire area that must be monitored, and in a

location where tampering with them is dicult.

• Lighting – Direct light shining on the camera lens or bright reections from shiny objects in the eld of view can diminish

video quality and camera performance. Mount the camera in shaded areas, if possible, or where light on the lens can be minimized.

• Ease of installation – Must be able to install the camera at the location, considering mounting hardware requirements,

temperature, dust, moisture, etc.

About weatherproof cameras

Weatherproof cameras can be mounted in any open area, such as on a telephone pole or on the side of a building. However, for best results, we recommend you mount your cameras in a sheltered area, such as under the eave or roof of a building. Point the camera in the direction you wish to observe. When routing cable near the camera, allow enough slack to form a U-shaped “drip loop” to help direct moisture or rain water, that accumulates on the cable, away from the camera.

Drip Loop

Drop Cable

NOTE

Cable connectors are not weatherproof.

Video/power cables can be run almost anywhere, and are frequently routed through attics or above drop/acoustic ceilings because of the ease of installation. For added security, we recommend you run your cables in areas with limited access to prevent tampering. Avoid running the cable near high voltage appliances such as uorescent lighting. Electrical noise and magnetic elds produced by these devices may aect video signal quality.

A 60’ video/power extension cable is shipped with every camera in your system. 100’ and custom-length cables are also available from Security Cameras Direct.

www.SecurityCamerasDirect.com

SECTION 2: INSTALLING YOUR SYSTEM

2.2.2 Mounting

1. Using the camera mounting bracket assembly plate as a template, mark the location for the mounting screws on the mounting

surface.

2. Drill holes into the mounting surface for the mounting screws, wall inserts, or other attachment hardware as needed.

3. If you are routing the video/power drop cable through the mounting surface, drill a ¾” hole near the mounting bracket for the

drop cable.

4. Attach the mounting bracket to the mounting surface using appropriate fasteners.

5. Attach the camera to the mounting bracket.

6. Loosen the directional adjustment screw and point the camera at your surveillance target, then tighten the screw to hold it in

place. (Note: This adjustment may need correction when video from the camera is observed.)

7. Route the camera drop cable through the hole drilled for it in the mounting surface, if used. If the camera is installed where

moisture may accumulate on it, leave a “drip loop” in the cable so that beads of water that collects on the cable ow away from the camera and the drop cable connectors.

8. Attach a video/power extension cable to the camera drop cable (see diagram below). Note: When connecting the video

cables, fully rotate the lock ring to hold them together.

Extension

Cable

Camera Drop Cable

Power

Video

Lock Ring

If the connectors might be exposed to moisture or other contaminants, seal them with electrical tape or other material.

9. Route the other end of the video/power extension cable to the DVR backpanel.

10. Repeat this procedure for all the cameras you are installing.

94-Camera H.264 Security System Setup Guide

SECTION 2: INSTALLING YOUR SYSTEM

2.3 Install and setup a monitor

1. Install and setup your monitor in accordance with the instructions provided with the monitor. Do not power it on at this time.

2. Cable the DVR Monitor Out (VGA) connector to your monitor’s VGA input. You can also use the monitor out BNC interface, but

the signal quality is better through the VGA interface.

Monitor Out

(BNC)

Monitor Out

(VGA)

NOTE

Some monitors have multiple inputs such including VGA ,HDMI, BNC, etc. If you are using this kind of monitor, congure your monitor to display the input from your DVR.

2.4 DVR installation

2.4.1 Placement

Your monitoring and recording equipment is central to constant surveillance and the reliable capture of video evidence. We strongly suggest that it be installed in a secure location with access limited to authorized personnel.

DVRs generate heat and should be placed in a ventilated area. A high temperature environment will reduce the life span and reliability of the equipment. Additionally, the DVR is not weatherproof, so avoid exposure to liquids and excessive dust. Do not place objects along the sides or behind the DVR that will block airow through the unit.

Uninterruptible power supplies

It is strongly suggested that power to the system be routed through an uninterruptible power supply (UPS). These devices will keep your security system running through most power outages, in addition to providing excellent surge and sag protection. The UPS should support your video recorder and all cameras to ensure normal operation during abnormal power conditions.

www.SecurityCamerasDirect.com

SECTION 2: INSTALLING YOUR SYSTEM

2.5 Connecting the components together

Video/Power Extension Cables

VGA Cable

5-Way Power

Splitter

To 120 VAC Monitor Power

Power Adapter

Camera

Drop Cable

To UPS/ 120 VAC

Typical Interconnection Diagram*

* NOTE: Power cabling shown in the previous diagram is recommended for systems with CFC6044IR cameras. If you are not installing CFC6044IR cameras, power requirements for your cameras may be dierent. Refer to the documentation provided with your camera for specic instructions and recommendations.

1. Connect the system mouse to the USB connector on the DVR back panel.

2. Connect the camera video signal cables (BNC connectors) to the VIDEO IN CH1 to CH4 connectors

114-Camera H.264 Security System Setup Guide

SECTION 2: INSTALLING YOUR SYSTEM

3. Connect a display device to the DVR. If using a VGA monitor for a display, connect it to the VGA MAIN OUT connector. If using

the BNC MAIN OUT connector to drive a display such as a TV, attach the appropriate cables between the BNC MAIN OUT and your display device.

4. Connect the 5-way power splitter to the power adapter, then:

a. Connect the lead marked DVR POWER to the DC 12V connector on the DVR back panel.

b. Connect the other leads of the splitter to the mating connectors on the video/power extension cables routed to the

cameras.

5. Connect the power cord to the power adapter and plug it into a standard grounded 120 VAC power source through a UPS or

surge protector.

6. Power on your system monitor.

7. Press the power button on the DVR front panel to power on the unit. A startup “Loading” screen will appear on the display.

After a few seconds, the screen will change to the camera view screen.

Note: The images you see from your cameras may be dierent from those shown here.

2.6 Adjusting the camera

Adjust your camera to produce the best performance:

• While observing video from your camera, loosen the directional adjustment set screw on the camera mounting assembly, aim

the camera at your surveillance target, then tighten the directional adjustment set screw.

www.SecurityCamerasDirect.com

SECTION 2: INSTALLING YOUR SYSTEM

Directional Adjustment Set Screw

• In brightly lit environments, adjust the sun shield as needed reduce light shining on the lens.

NOTE

If you are installing a dierent camera, refer to the documentation provided to setup the camera.

134-Camera H.264 Security System Setup Guide

SECTION 3: SYSTEM SETUP

SECTION3

System Setup

Setting up your DVR includes logging into your DVR, setting the clock, setting administrator and user account passwords, and setting up scheduled and/or automated motion recording.

3.1 Login to the DVR

Initially, two access accounts are provided in your system: Admin and user1. With the Admin login, you can make conguration changes to the system, create user accounts and passwords, and control the privileges allotted to each account. With the factory default user1 account login you cannot make conguration changes or create accounts, but can change your own password. The factory default Admin and user1 account passwords are:

Admin: 888888 user1: 666666

To log into the system:

1. Power on the DVR and wait until it advances to the camera view screen. A typical camera view screen is shown below.

NOTE

During initial startup of the system, no password is required.

Image from

Channel 1

Camera

2. Press the MENU button on the front panel twice, or right-click the mouse twice anywhere on the screen. An Input

Password window will appear.

www.SecurityCamerasDirect.com

SECTION 3: SYSTEM SETUP

Conrm entry

3. Click the q icons to the right of the User Name eld parameter eld and select Admin. To make conguration changes to the

system, you must login to the Admin account.

4. Using the mouse, click the entry eld on the PASSWORD line, then click the number buttons that appear to enter the account

password. For example, to enter the default Admin password, 888888, click the “8” button six times.

5. Click the a (check mark) icon in the lower right corner of the window to conrm your entry and enter the login information.

A tool bar icon strip will appear at the bottom of the screen.

3.2 Conguring the system

Basic system conguration settings include setting the screen language, video system format, system time, creating users, initializing the hard disk drive (HDD), and setting up automated recording.

1. If the system is not running, power on the DVR and wait until it completes initialization.

2. Right-click anywhere on the desktop, or press the MENU button. A status bar will appear.

3. Compare the DVR system date and time shown on the Status Bar with an accurate clock.

System Date and Time Remaining HDD Recording TIme

Status Bar

Note: To see an accurate clock, access a reliable Internet time server, such as tf.nist.gov

4. Right-click the mouse anywhere on the screen again. The Status bar will change to a Tools Bar or a login window. If a LOGIN

window opens, log in to the system as an Admin (see above).

154-Camera H.264 Security System Setup Guide

SECTION 3: SYSTEM SETUP

PIP*2

PIP*1

System Settings

EZoom

Play

Manual Record /

Stop Manual Record

VGA / BNC

Switch

Auto

Sequence

Keylock

Tool Bar

5. Click the Settings button on the Tool Bar.

3.2.1 Settingthescreenlanguageandvideosystemformat

1. In the Settings window SYSTEM tab, click the q icon at the right end of the LANGUAGE line. Select (click) the screen

language you prefer from the dropdown list.

2. If the VIDEO SYSTEM option does not indicate NTSC, click the q icon at the right end of the VIDEO SYSTEM line, then select

NTSC from the dropdown list.

3.2.1 Settingthesystemtime

1. On the TIME line, click the >> icon to open the TIME SETUP window.

www.SecurityCamerasDirect.com

SECTION 3: SYSTEM SETUP

2. Click the q icon at the right end of the DATE FORMAT line. Select the format you prefer: MM/DD/YY, YY-MM-DD, or DD-

MM-YY.

3. Click the entry on the DATE line. Click the t or u icons to highlight a digit of the date, then click the number value of the

digit To complete the entry and close the virtual keyboard, click the = button.

4. Click the q icon at the right end of the TIME FORMAT line. Select the format you prefer: 12 hour or 24 hour.

5. Click the entry on the TIME line. Click the t or u icons to highlight a digit of the current time, then click the number value of

the digit. To complete the entry, click the = button.

174-Camera H.264 Security System Setup Guide

SECTION 3: SYSTEM SETUP

6. If you selected a 12 hour time format, click the q icon on the line below the TIME entry, then select either AM or PM.

7. On the DST line, click the >> icon to open the DST (ON/OFF) option window. If you select ON, a DST setup window will open.

Use the method like that detailed above to setup the DST start and end time, then click the conrm entry check (

a) in the

lower right corner to conrm your entries.

8. Click the CONFIRM button in the NOTE window.

3.2.2 ChangetheAdminanduser1passwords

Changing the default Admin and user1 account passwords from their initial (default) value adds security to your system. The factory default account names and their passwords are:

Admin: 888888 user1: 666666

To change these passwords:

1. With the system powered on, right click twice on the desktop or press the menu button on the front panel twice, then log into

the system as the Admin (if a password login is required).

2. Click the Settings icon on the Tool Bar. The SYSTEM tab window will open.

1. On the USER line, click the >> icon to open the USER MANAGEMENT window.

2. On the CHANGE PASSWORD line, click the >> icon to open the USER MANAGEMENT window.

www.SecurityCamerasDirect.com

SECTION 3: SYSTEM SETUP

3. Click the q icon at the right end of the USER NAME line. From the dropdown list, select Admin.

4. Click the OLD PASSWORD entry eld, then enter the current Admin password using the virtual keyboard.

5. Enter both the NEW PASSWORD and CONFIRM PASSWORD elds with a dierent password. Passwords cannot be more

than 6 digits in length.

6. Click the conrm icon ( a) in the lower right corner of the screen, then click the Conrm button in the Note window.

7. Repeat steps 3, 4, 5, and 6 above to change the user1 password.

3.2.3 Addusestothesystem

1. On the SYSTEM tab USER line, click the >> icon to open the USER MANAGEMENT window.

2. In the USER MANAGEMENT window, click the >> icon on the ADD USER line.

3. Click the entry eld on the USER NAME line to open a virtual keyboard. Click the letters and numbers to enter a username,

then click the = icon to close the keyboard.

4. Enter both the PASSWORD and CONFIRM PASSWORD elds with a password for the user. Passwords cannot be more than

6 digits in length.

5. Click the conrm icon ( a) in the lower right corner of the screen, then click the Conrm button in the Note window.

6. Press the MENU button on the front panel or right click on the desktop to return to the USER MANAGEMENT window.

7. In the USER MANAGEMENT window, click the >> icon on the SET PERMISSIONS line.

194-Camera H.264 Security System Setup Guide

SECTION 3: SYSTEM SETUP

8. Click the q icon at the right end of the USERS line. From the dropdown list, select the name of the user you just created.

9. Click the OPT checkboxes to assign permissions to the new user.

10. Click the conrm icon (a) in the lower right corner of the screen, then click the Conrm button in the Note window.

11. Press the MENU button on the front panel to return to the USER MANAGEMENT window, then press the MENU button again

to return to the SETTINGS window SYSTEM tab.

3.2.4 SetHDDoverwriteoption

1. On the SYSTEM tab HDD line, click the >> icon to open the HDD MANAGEMENT window.

2. Click the q icon at the right end of the OVERWRITE line. From the dropdown list, select the option you prefer:

www.SecurityCamerasDirect.com

SECTION 3: SYSTEM SETUP

— Close: When the HDD becomes full, no additional recordings are written to the HDD — Overwrite: Recordings on the HDD are overwritten when the HDD becomes full. The oldest recording is overwritten

rst.

— 1 HOUR .. 90 DAYS: Recordings are overwritten when older than the time selected.

3. Click the conrm icon ( a) in the lower right corner of the screen, then click the Conrm button in the Note window.

4. Press the MENU button on the front panel or click on the desktop to return to the SYSTEM tab.

3.3 Record conguration settings

The recording settings of each camera channel can be specied separately or collectively. These settings, including the recording schedule for each channel, are setup through the Record tab.

1. Click the Settings icon on the Tool Bar. The SYSTEM tab window will open.

2. Click RECORD to open the RECORD settings menu.

3. Click the q icon at the right end of the CHANNEL line. From the dropdown list, select the number of the camera channel you

want to setup, or select ALL to congure all channels with the same settings.

4. Click the q icon at the right end of the RECORD line. From the dropdown list, select DISABLE, or ENABLE to record video from

the channel.

5. Click the q icon at the right end of the BITRATE line. Select GOOD, NORMAL, or LOW. A GOOD bitrate produces the best

recording quality, but uses more processing power and hard disk space.

214-Camera H.264 Security System Setup Guide

SECTION 3: SYSTEM SETUP

6. Click the q icon at the right end of the RESOLUTION line. From the dropdown list, select D1 (720 × 486), HD1 (720 × 240),

or CIF (352 × 288).

7. Click the q icon at the right end of the FRAME RATE line. From the dropdown list, select a number between 1 and 30

(frames per second). The higher the frame rate (30 fps), the smoother the video motion. However, higher frame rates consume storage space faster.

8. Click the q icon at the right end of the PACKTIME line. From the dropdown list, select either 15, 30, 45, or 60 (minutes).

Packtime is the time length of video le segments that are o-loaded (backed up).

9. Click the q icon at the right end of the RECORD MODE line. From the dropdown list, select either ALWAYS or SCHEDULE.

ALWAYS causes the DVR to record continuously. Selecting SCHEDULE allows you to open a window to congure the DVR to record by the hour of the day and day of the week, either by motion sensing, continuous recording, or not recording. See Scheduled recording below.

10. If you are conguring the camera channels dierently, repeat this procedure for the other camera channels.

Scheduled recording

If the RECORD MODE -SCHEDULE is selected:

11. Click the >> icon on the RECORD tab to open the RECORD SCHEDULE SETUP window.

12. Click the q icon at the right end of the CHANNEL line. From the dropdown list, select the channel number to apply the

recording schedule to, or select ALL to apply the schedule to all cameras.

13. At the bottom of the window, click either the MD (motion detection) or NORMAL (continuous recording) checkbox, then click a

box in the time array to apply that method of recording to that timeslot.

www.SecurityCamerasDirect.com

SECTION 3: SYSTEM SETUP

In the example above, NORMAL recording was scheduled for Monday through Saturday between 7 AM and 8 PM. MD recording was scheduled for Monday through Saturday between 3 AM and 7 AM and between 8 PM and midnight, and on Sunday between 3 AM and midnight.

14. Click the conrm icon (a) in the lower right corner of the screen, then click the Conrm button in the Note window.

15. If you setup the record schedule for a single channel, repeat this procedure to setup the other camera channels.

16. Press the MENU button on the front panel to return to the RECORD tab.

3.4 Video conguration settings

The video conguration settings aect the appearance of the camera video on the monitor. The conguration can be se setup for each individual camera, or the same settings can be applied to all cameras.

1. Click the Settings icon on the Tool Bar. The SYSTEM tab window will open.

2. Click VIDEO to open the VIDEO settings menu.

3. Click the q icon at the right end of the CHANNEL line. From the dropdown list, select the number of the camera channel you

want to setup, or select ALL to congure all channels.

4. Initially, camera channels are named CH1 .. CH4. You can change the name of the channel by clicking on the entry eld on the

NAME line to open a virtual keyboard. Use the keyboard to enter a new name, if needed, then click the = button to close the keyboard.

5. Click the q icon at the right end of the POSITION line. The position option selects where the camera channel NAME appears

on the live display. Choose one of the owing: U-L (upper left), D-L (lower left), U-R (upper right), or D-R (lower right).

234-Camera H.264 Security System Setup Guide

SECTION 3: SYSTEM SETUP

6. Click the q icon at the right end of the LIVE line. In the dropdown list, select ON (to view video from the camera on the Live

screen), or OFF.

7. On the COLOR line, click the >> icon to open the COLOR SETUP window.

The COLOR SETUP window is superimposed on the video image from the camera channel you selected. Adjust the markers for the HUE, BRIGHTNESS, CONTRAST, and SATURATION to produce the best picture from the camera.

8. Click the conrm icon ( a) in the lower right corner of the screen, then click the Conrm button in the Note window.

9. If you setup the record schedule for a single channel, repeat this procedure to setup the other camera channels.

10. Press the MENU button on the front panel to return to the RECORD tab.

3.4.1 Videosetup

The VIDEO SETUP menu provides conguration settings for the monitor screen resolution, sequential live view settings, and video blocking.

1. Click the Settings icon on the Tool Bar. The SYSTEM tab window will open.

2. Click VIDEO to open the VIDEO settings menu.

3. On the VIDEO SETUP line, click the >> icon to open the VIDEO SETUP menu.

www.SecurityCamerasDirect.com

SECTION 3: SYSTEM SETUP

4. Click the q icon at the right end of the VGA line. Select one of the options: 1024 x 768 or 1280 x 1024. NOTE: Changing this

setting from the current value will cause a DVR restart.

5. Click the entry eld on the SEQUENTIAL TIME line, then enter a number between 1 and 300 (seconds). This option sets the

pause duration when sequentially displaying the live video from each camera in full screen.

Video blocking

For security or privacy reasons, some areas of the video elds of view are be blocked. To setup the blocking:

6. In the VIDEO SETUP menu, click the q icon at the right end of the CHANNEL line, then select a video channel number from

the dropdown list.

7. On the AREA COVERED line, click the >> icon. Video from the camera will appear in full screen mode.

8. Block areas of the video image by pressing the left mouse button and dragging to create a box over the areas you want to

block. In the following image, two block boxes cover windows for privacy.

254-Camera H.264 Security System Setup Guide

SECTION 3: SYSTEM SETUP

Privacy

Blocks

After the block is created, it can be repositioned by dragging it with a mouse.

To remove a block, double click on it.

9. Right click anywhere on the desktop to return to the VIDEO SETUP menu.

10. Click the conrm icon (a) in the lower right corner of the screen, then click the Conrm button in the Note window.

11. Repeat this procedure for the other camera channels, if necessary.

3.5 Network conguration settings

Use the NETWORK menu to congure your DVR for use on a LAN, for access through the Internet, for access from a smartphone, and for issuing automated email when alarm conditions occur.

Refer to the Chapter 4, Networking your DVR for conguring your system for local LAN and Internet access. For other network settings, including DDNS, EMAIL, MOBILE, and OTHER SETTINGS, refer to the chapter DVR System Menus.

NOTE

The default IP addresses and port settings of your DVR may be dierent from those shown in this document. Always use network settings that are compatible with your network(s).

3.6 Alarm conguration settings

Use the ALARM menu to congure your DVR for behavior when the hard disk drive becomes full, and for motion detection sensitivity of each channel.

1. Click the Settings icon on the Tool Bar. The SYSTEM tab window will open.

2. Click the ALARM tab to open the ALARM settings menu.

www.SecurityCamerasDirect.com

3. Click the q icon at the right end of the DURATION line. From the dropdown list, select either 30 SEC .. 5 MIN. This option sets

the recording time length after an alarm recording is activated.

4. Click the q icon at the right end of the BUZZER line. From the dropdown list, select either OFF, or 5 SEC .. 60 SEC. This option

sets the buzzer sounding time when the alarm is triggered.

5. Click the q icon at the right end of the PRERECORD line. From the dropdown list, select either OFF or 5 SEC. This option

disables or enables recording 5 seconds of video before the alarm occurred.

6. Click the >> icon on the EXCEPTION line to open the EXCEPTION ALARM menu.

7. Click the >> icon at the right end of the HDD FULL line. This feature enables the buzzer sound when the HDD is nearly full.

Select either OFF, 1 G (remaining), 5 G ,10 G, 1 HOUR, 5 HOUR , 10 HOUR, or 20 HOUR.

SECTION 3: SYSTEM SETUP

274-Camera H.264 Security System Setup Guide

SECTION 3: SYSTEM SETUP

8. Click the checkbox to the right of the HDD LOSS label to enable this alarm. When the HDD is not available, this feature will

sound the buzzer and place the

on the desktop.

9. Click the checkbox to the right of the VIDEO LOSS label to enable this alarm. When a video signal from a channel is not

detected, this feature will sound the buzzer and place the Video Loss label in the channel LIVE view window.

10. After conguring your network settings, click the conrm icon ( a) in the lower right corner of the screen, click the Conrm

button in the Note window.

11. Press the MENU button on the front panel, or right click anywhere to return to the ALARM menu.

3.6.1 Motiondetectionsetup

Motion detection can be congured for each channel individually, or you can apply the same settings to all channels at one time.

1. On the ALARM tab menu, click the >> icon on the MOTION line to open the MOTION DETECTION SETUP menu.

2. Click the q icon at the right end of the CHANNEL line. From the dropdown list, select the camera channel number you want

to setup, or select ALL to congure all channels.

3. Click the q icon at the right end of the SWITCH line. From the dropdown list, select ON or OFF to enable or disable motion

detection on the channel(s).

www.SecurityCamerasDirect.com

SECTION 3: SYSTEM SETUP

4. Click the q icon at the right end of the SENSITIVITY line. From the dropdown list, select 1 .. 8 to set the level of sensitivity.

1 is highest, 8 is lowest. High sensitivity may cause an alarm when a small object, such as a bird or mouse, passes through the eld of view, whereas the lowest sensitivity level may be appropriate for detecting only cars that pass by. This setting is dependent on the what you want to detect, and usually requires testing to nd the best value.

5. Click the >> icon on the MD AREA line to specify the areas where of the screen where motion should be sensed. Dening

only these areas (and ignoring other areas) of the eld of view improves the performance of the DVR.

The Motion Detection setup screen is partitioned into a grid of 10 x 15 blocks. Motion sensing in each block can be toggled on and o by clicking the block area. Initially, all blocks are shaded purple, indicating that motion sensing is disabled everywhere.

To enable blocks (areas) for motion sensing, click the block, or use the mouse to drag a rectangle over areas you want to enable. The shading will disappear for areas selected for motion detection. To disable an area selected, click on it.

Motion Sensing

Disabled

Motion Sensing

Enabled

6. After the motion sensing areas are selected (unshaded), right click to return to the MOTION DETECTION SETUP menu.

7. Check the box to right of the RECORD label to enable recording when motion is detected.

8. Check the box to right of the BUZZER label to sound the buzzer when motion is detected.

294-Camera H.264 Security System Setup Guide

SECTION 3: SYSTEM SETUP

9. Check the box to right of the PRERECORD label to add the previous 5 seconds of video from the camera to the motion

detection recording.

10. Check the box to right of the EMAIL label to send an email when motion is sensed. To use this feature, the EMAIL conguration

settings in the NETWORK tab must be congured.

11. After conguring your network settings, click the conrm icon (a) in the lower right corner of the screen, then click the

Conrm button in the Note window.

12. Repeat the steps above for the other camera channels.

www.SecurityCamerasDirect.com

SECTION 4: NETWORKING YOUR DVR

SECTION4

Networking Your DVR

Your DVR supports highly exible networking congurations including an Ethernet connection, such as to a home network with a broadband router and modem, and a PPPOE connection. In this section, only general guidelines for the setup of a DVR on a simple Ethernet broadband home network are included. If you encounter problems you cannot resolve, contact the Security Cameras Direct Support team at 1.800.316.6027.

Home networks

A typical home network includes router, one or more computers, and a broadband modem for access to an internet service provider (ISP) and the internet. The DVR attaches to the network like a computer, except that it has preset IP address settings that must be congured for your network.

DVR

Router

Broadband Modem

Home Network

Computer

Web Connected

Computer

DVR Monitor

Home Network

Setting up the DVR on the home network requires conguring it with IP address settings that are compatible with your network, and connecting an Ethernet cable between the DVR and the router. Once setup, your security system can be monitored and controlled from any computer on the network with the Microsoft

Internet Explorer (IE) browser.

314-Camera H.264 Security System Setup Guide

SECTION 4: NETWORKING YOUR DVR

After the DVR is setup on your home network, usually the router can be congured so that the DVR is accessible from a computer on the Internet or from a smartphone. Although most routers perform similar functions, the specic procedures to congure them vary widely. However, the documentation provided with your router, with the general guidelines included here, should enable you to setup your DVR for web access.

4.1 Congure the DVR for access on your home network

To setup your DVR on the network without conicting with other devices, congure the network settings of your DVR before physically connecting it to the network. Network conicts occur when two devices on the network have the same IP address. The screens shown here were taken from a Windows XP system:

1. Determine the IP address, subnet mask, and default gateway of your home computer (PC) and record it in Table 1. To get this

information, do the following at the Windows desktop:

a. Open the Windows Start menu and click Run to open the Run dialog box.

b. Type cmd in the entry eld and then click OK to open the DOS command window.

c. At the command prompt, enter ipcong. The PC will display Ethernet data associated with your Ethernet adapter local

area network (LAN) connection.

Example:TypicaluseofipconginWindowsXP

www.SecurityCamerasDirect.com

SECTION 4: NETWORKING YOUR DVR

d. Enter the IP Address, Subnet Mask, and Default Gateway for your PC’s Ethernet adapter into Table 1.

NOTE

The Ethernet adapter data you see by using ipcong will probably be dierent from that shown in the example above. If you are using Windows Vista or Windows 7, the IP address is identied as the “IPv4 Address.”

Table1.PC/DVRnetworksettings

Compu ter (PC) DVR

IP Address

Subnet Mask

Default Gate way

2. At your PC, nd an IP address on your network that is not in use:

a. Write down the EXACT IP address of your PC up to the third/last period. Using the example shown above in the screen

capture of ipcong, this number would be: 192.168.1.

b. After the third period, choose any number between 1 and 255 that is dierent from the one in your PC’s IP address, 168.

As a rst try, let’s choose 100, which will form the IP address 192.168.1.100.

c. Next, use the ping command in the DOS window to see if that IP address is in use on your network. The format of the

ping command is:

ping <IP address> For this example here, we entered: ping 192.168.1.100

To test your IP address, enter ping 192.168.1.100. Any reply received from the ping indicates that a device on the network is already using this IP address and you can connect to it.

334-Camera H.264 Security System Setup Guide

SECTION 4: NETWORKING YOUR DVR

d. Examine the screen capture shown above. If the response to the ping command was “Request timed out.” like that

shown above, use this IP address for your DVR, enter into Table 1, skip steps 2.e and continue at step 2.f.

If the response to the ping command was “Reply from 192.168.1.100: ..” as shown below, a device exists on the network that is using this IP address. If so, continue at step 2.e.

e. Since the response to ping test returned a reply as shown above, try the ping with another number between 1 and 255

until one is found that responds with the “Request timed out.” message. Use this IP address with your DVR and enter it into Table 1.

f. In table 1, copy the PC’s Subnet Mask and Default Gateway entries into the DVR’s Subnet Mask and Default Gateway

cells.

3. At your DVR, click the System Settings icon on the Tool Bar. The SYSTEM tab window will open.

System Settings

4. Click NETWORK to open the NETWORK settings menu.

NOTE

The default IP addresses and port settings of your DVR may be dierent from those shown in this document. Always use network settings that are compatible with your network(s).

www.SecurityCamerasDirect.com

SECTION 4: NETWORKING YOUR DVR

5. On the NETWORK line, click the >> icon to open the NETWORK SETUP menu.

6. Click the q icon at the right end of the TYPE line. From the dropdown list, select either DHCP, PPPOE, or STATIC for the IP

network setup. If you select DHCP or PPPOE, the DVR will acquire its network settings automatically. If you select STATIC, you can congure your network settings manually by clicking on the entry eld and using the virtual keyboard to enter data. See the following screen capture.

354-Camera H.264 Security System Setup Guide

SECTION 4: NETWORKING YOUR DVR

NOTE

The MEDIA PORT, WEB PORT, and SETUP PORT numbers do not need to be changed unless these numbers conict with other devices on your network.

7. Congure your DVR with a DNS address, IP ADDRESS. SUBNET MASK, and GATEWAY address compatible with your local

network.

8. After conguring your network settings, click the conrm icon (a) in the lower right corner of the screen, then click the

Conrm button in the Note window.

9. Press the MENU button on the front panel, or right click anywhere to return to the SETTINGS menu.

10. At the SETTINGS menu, click the SYSTEM tab, then click the >> icon on the MAINTENANCE line.

11. Click the >> icon on the REBOOT line, then follow the on-screen prompts to reboot your DVR.

12. Connect an Ethernet cable between the LAN port on the back of your DVR and any open port on your router.

13. At your PC, use the ping command with your DVR’s IP address to conrm that you can connect to your DVR from your PC. At

the DOS prompt in the Command window, enter:

ping <IP address>

where <IP address> is the new DVR IP address. For example, if your DVR’s IP address is now 192.168.1.100, enter

ping 192.168.1.100

14. Examine the response to the ping command. If the response is “Reply from ...” and NOT “Request timed out.” as before,

your DVR is now congured on the network.

www.SecurityCamerasDirect.com

4.1.1 VerifylocalnetworkconnectabilitywithIE

After your DVR is setup on a local network, IE is used to verify connectability across the LAN. It also increases exibility for monitoring and conguring your security system.

Before you can connect to the DVR with IE, the (default) security settings in IE are modied and an additional software is installed.

1. At your PC, load IE.

2. Open the IE Tools pull-down menu and select Internet Options. Click the Security tab.

3. Click the Custom Level... button. In the Settings list, change the following settings to Enable:

— Automatic prompting for ActiveX controls — Initialize and script ActiveX controls not marked as safe for scripting — Script ActiveX controls marked safe for scripting — Binary and script behaviors — Download signed ActiveX controls — Download unsigned ActiveX controls — Run ActiveX controls and plug-ins

SECTION 4: NETWORKING YOUR DVR

374-Camera H.264 Security System Setup Guide

SECTION 4: NETWORKING YOUR DVR

Click OK, then click YES in the Warning window.

In the Internet Options window, click Apply, then click OK to close the window.

NOTE

If your computer operating system is Windows Vista or Windows 7, User Account Control can interfere with the normal operation of the DVR user interface. To disable UAC, open the Control Panel > User Account > User Account window, clear the Use User Account Control (UAC) to help protect your computer check box, then click OK. A computer restart may be required.

www.SecurityCamerasDirect.com

SECTION 4: NETWORKING YOUR DVR

4. In the IE URL eld, enter the IP address assigned to your DVR with the WEB PORT number congured in your DVR (in the

example above, the default WEB PORT is 8090). Using the example shown above, enter:

192.168.1.100:8090

NOTE

After sending the URL, IE may prompt you to load the Chinese Simplied language pack. You can click Install or Cancel. If you click Cancel, the message will reappear again when you logout and login.

5. During the rst connection to an ECO4 series DVR, a security warning to install software appears. Click Install and follow the

on-screen instructions to complete the installation.

6. When the Login screen opens in the browser, enter the administrator USER ID and PASSWORD, then click Login. The default

values for the administrator account are Admin and 888888.

394-Camera H.264 Security System Setup Guide

SECTION 4: NETWORKING YOUR DVR

7. After login, the DVR web display will appear. To see images from the cameras connected to your DVR, click the Open All

button in the lower left corner of the screen.

www.SecurityCamerasDirect.com

SECTION 4: NETWORKING YOUR DVR

NOTE

When viewing the DVR network browser interface, if the webpage appears normal but the camera images are scrambled, check your computer’s video adapter settings, or call Security Cameras Direct Support at 1.800.316.6027 for assistance.

4.2 Accessing your DVR from the Internet

The remote viewing capabilities of your DVR allow you to access and control it from anywhere in the world via the Internet. Your DVR must be setup on a LAN before this capability can be enabled, and the LAN must have a high-speed connection to the Internet for ecient data transfer to occur. This procedure requires that the network router be congured to enabling port forwarding to your DVR. Only general instructions for setting up this capability are included here.

NOTE

Security Cameras Direct provides complete technical support for viewing your DVR within your LAN. However our support team cannot assure complete technical assistance for products from other manufacturers, such as routers and modems. Refer to your product documentation, or contact your service provider for support on setting up port forwarding.

1. Congure your router for port forwarding to the DVR using the network information included in Table 1. For instructions, refer

to the user documentation for your router and/or the information and service provided at http://portforward.com.

Port forw arded for the DVR:

CAUTION



By default, your DVR uses port 8090 for the web port, 9000 for the Media port, 10510 for the Mobile server port, and 8000 for the Setup port. If any of these ports are assigned to another device on your network, congure your DVR to use a dierent port. Do not assign the ports used by your DVR for Web, Media, Setup or Mobile to any other device on your local network. Also, when choosing a port for port forwarding an Internet connection to your DVR, do not use any of these ports, or other ports on your network already in use.

2. Determine if your router/modem has a dynamic IP address (one that can change arbitrarily, often used by internet service

providers (ISPs) for cable/DSL modems) or static IP address (unchanging). If you are unsure, contact your ISP for this information. If you use a dynamic IP address for your modem, go to step 4.

3. To nd the static IP address assigned to your LAN, go to http://www.whatismyip.com/ from a PC on the same network

(LAN) as your DVR. The IP address displayed is the IP address you will use to log in remotely. Keep this in your records. Skip to step 6.

Static IP Address:

4. If you have a dynamic IP address, it is convenient and recommended to use a dynamic name server service, such as http://

www.dyndns.com/ (a free service), to setup a remote connection with a xed hostname to your DVR. If you use DynDNS,

the following steps are helpful:

414-Camera H.264 Security System Setup Guide

SECTION 4: NETWORKING YOUR DVR

a. On dyndns.com under “Resources”, select Home DNS Solutions.

b. On the “Home Solutions” page, click the link for Dynamic DNS.

c. Under “Documentation” select the link How-To.

d. Follow the instructions to set-up an account. Record the DynDNS Hostname, DynDNS Username and DynDNS Password

in the table below.

DynDNS Host name: .dyndns.org

DynDNS User name:

DynDNS Password:

5. After setting up a DynDNS account, the (dynamic) IP address specied in the account Hostname must be updated whenever

it changes. Depending on your system conguration, either of two options can be used to automatically update the IP address set in your DynDNS Hostname.

a. If you have a PC running continuously on the LAN with the DVR, do the following to download and install software that

automatically updates your DynDNS account when the IP address of your router changes:

i. Go to http://www.dyndns.com/support/clients and click on the Download link.

ii. Install the “Updater” program. When prompted, make sure you select Install as Windows Service.

iii. Enter your DynDNS Username and Password, and select your Hostname.

iv. Click Apply. Your PC should now automatically update your DynDNS Hostname settings with your current IP

address.

b. If you have a DDNS-supported router (see manufacturers information), do the following to congure your router to

automatically update your DynDNS with the current IP address.

i. Login to your router (see manufacturer’s instructions).

ii. Search for a page, tab, or conguration setting labeled “DDNS”.

iii. Enter your DynDNS Hostname, Password and Username.

iv. Save or Apply these settings. Your router should now automatically update your DynDNS with your current IP

address.

www.SecurityCamerasDirect.com

SECTION 4: NETWORKING YOUR DVR

6. Whether you have a static IP address, or you set up a DynDNS account for a dynamic IP address, the following are dierent

ways to view your DVR from a PC on the Internet:

a. In the URL eld of your Internet browser, enter the current IP address of your modem with router port number (port

forwarded for your DVR) assigned to your DVR in the format: http://<IP address:port> For example, if the IP address of your modem is 190.180.170.32 and the port forward number is 85, enter: http://190.180.170.32:85

b. Access the DVR using your DynDNS account and hostname.

434-Camera H.264 Security System Setup Guide

SECTION5

Accessing Your DVR With a Web Browser

After your DVR is “networked” for LAN and Internet access, it can be monitored and congured remotely. Also, you can search for and download video clips to your remote computer. The examples presented herein access the DVR through the Microsoft Internet Explorer (IE) browser.

5.1 Connecting to your DVR with IE

There are dierent ways to connect to your DVR, depending on how it is networked.

• If the computer you are using to access your DVR is on the same local network as your DVR, you can access it with Microsoft

Internet Explorer (IE ) using placing the IP address and Webport of the DVR in the IE URL eld. For example, the URL address HTTP://192.168.1.100:8090 uses an IP address of 192.168.1.100 and a webport number of 8090.

• If you are accessing your DVR from the internet, the network modem/router where your DVR is installed is 77. 67.214.84, and

your DVR is congured on the router port of 2000, the URL for your DVR would be HTTP:// 77. 67.214.84:2000.

• If the Internet Service Provider you are using assigns a dynamic (changing) IP address to your modem/router (typical), you

can establish a xed URL for your modem/router using a web-based service such as DynDNS.com. With that service, your DVR might be addressed as HTTP://JDSmithDVR.dyndns.com.

After connecting to your DVR with IE, a login window will appear.

SECTION 5: ACCESSING YOUR DVR WITH A WEB BROWSER

www.SecurityCamerasDirect.com

SECTION 5: ACCESSING YOUR DVR WITH A WEB BROWSER

In the Login window, enter a USER ID and PASSWORD, then click LOGIN. The USER ID “Admin” has complete privileges to manage the DVR remotely. The default password for USER ID Admin is “888888”.

5.2 Live screen

After logging in to your DVR, the Live screen will appear. The Live screen displays real-time video from the DVR.

Stop View

1-Channel View

4-Channel View

Full Screen

Snap

Record

Using the buttons in the right frame, you can stop viewing live video, snap a photo of one of the video channels, or record video from all channels. You can also view all four channels at the same time (see above screen capture), only one channel on the screen, or expand one channel to ll your monitor screen.

• Stop View: Click the Stop View icon to stop viewing live video.

• Snap: Click the Snap icon to capture a photo of the selected video channel. To select a video channel on a multi-channel

display, click the image. The selected channel is framed with a blue border. The photo is saved in JPG format at the location shown in the pop-up window.

• Record: Click the Record icon to record the channels displayed. Each channel is recorded individually. Recordings are saved

in the location shown in the pop-up window. These video les are saved in AVI format, and can be played with any AVI compatible player such as HsPlayer (provided on the mini-CD with your DVR), VLC Media Player, or Windows Media Player.

454-Camera H.264 Security System Setup Guide

5.3 Replay window

The Replay window enables you to play and download recorded video. To use this feature:

1. In the calendar frame, click the date when the video was recorded. In the following example, September 15, 2011 was

selected.

2. From the list that appears, click the label for video le you want to play or download. The labels indicate the time of day when

the video was recorded, the channel that was recorded, and the size of the video clip.

3. Click the PLAY button at the bottom of the screen. Use the play control buttons below the view window to control the

playback.

To download the video clip to your computer, click DOWNLOAD. The clip will be saved in the location specied in the LOCAL SETTING screen, the download progress will appear at the bottom of the view window, and the path and name to the video le will be displayed with the download is complete.

4. Click on another le to play, or click the T icon in the upper -right corner to close the Replay window before selecting another

screen or window.

5.4 Remote window

The Remote window allows you to congure your DVR from your local computer if you logged in with the Admin USER ID. To expand the menu tree and open a conguration menu, click the “plus” box to expand the tree, then click the menu you want to see.

SECTION 5: ACCESSING YOUR DVR WITH A WEB BROWSER

www.SecurityCamerasDirect.com

The options on these screens are identical to those in the DVR menu system. Refer to the chapters Installing the System and DVR Menu System in this document for more information. After making changes to a Remote setting menu, click the SETUP

button at the bottom of the window to commit the changes.

Click the T icon in the upper-right corner to close the Remote Setting window before selecting another screen or window.

5.5 Local setting

In the Local Setting window, you can specify the locations on your computer where you want to save the recordings, frames, and les from your DVR.

SECTION 5: ACCESSING YOUR DVR WITH A WEB BROWSER

474-Camera H.264 Security System Setup Guide

SECTION 5: ACCESSING YOUR DVR WITH A WEB BROWSER

Click the T icon in the upper-right corner to close the Remote Setting window before selecting another screen or window.

5.6 Logout

Clicking LOGOUT returns you to the USER LOGIN screen.

5.7 Accessing the DVR with Mozilla® Firefox® or Google

Chrome™ browsers

Using Mozilla Firefox

To use Mozilla Firefox with your DVR, install the add-on IE TAB. This add-on embeds IE in a Firefox tab. To obtain IE TAB and its usage instructions, refer to the Mozilla website.

Google Chrome

To use Google Chrome with your DVR, install the additive le IE TAB. This le is named embeds IE in a Chrome tab. To install IE TAB, download the le extension_1_4_30_4.crx , then drag it into a Chrome tab window. Follow the on-screen instructions to install the feature.

www.SecurityCamerasDirect.com

SECTION 6: KWEYE SMARTPHONE APP

SECTION6

KWeye Smartphone App

KWeye is a free smartphone app for use with your Security Cameras Direct model ECO4IR and ECO4LCD system. Its features include:

• Compatible with most models of these phones: Apple iPhone, iPad, and iPod Touch, Google Android, Symbian, Windows

Mobile, Blackberry

• Unlimited video on cellular and WiFi networks

• Support for authentication

• Direct stream connection (video does not pass through a 3rd party server)

• Snapshot capability (while viewing live stream) to save to your local photo gallery

• Support for landscape and portrait views

• Ability to change IP address and port as needed for internal and remote users

This guide includes installation and use of KWeye with the Apple and Google smartphones. For more information, go to:

• iPhone, iPad, and iPod touch: http://itunes.apple.com/us/app/kweye/id412413785

• Android phones: https://market.android.com/details?id=com.KWeye

• For other smartphones, contact Security Cameras Direct Support at: 1.800.316.6027

To use this application, your DVR network must be setup to allow access from the Internet.

6.1 Installing KWeye

6.1.1 Installing KWeye in iPhone

KWeye can be acquired from the iTunes App Store > Productivity group. It can be downloaded and installed directly to your iPhone, or downloaded into a computer with iTunes, then installed on your iPhone. Before downloading applications from the App Store you must create a store account.

• To download and install KWeye directly to your iPhone: — Connect your iPhone to a high-speed network, such as a WiFi network (to shorten download time). — Open the App Store application on your iPhone, then search for kweye. — Download and install KWeye as you would any application.

494-Camera H.264 Security System Setup Guide

SECTION 6: KWEYE SMARTPHONE APP

App Found Ready to Install Installed

• To download KWeye to your computer then install it on your iPhone: — Download and Install the latest version of Apple iTunes if not already installed. You can download iTunes from

ww.apple.com/itunes/ A computer restart may be required.

— Open iTunes. — Click the iTunes Store item in the list on the left, then login to your iTunes Store account. If you don’t have an iTunes

Store account, follow the on-screen instructions to create one.

— In the Search Store eld in the upper right corner of the screen, enter kweye.

— After KWeye is found, click the Free App button, then click Buy in the popup window to download the application.

KWeye will appear in your iTunes LIBRARY > Apps list.

www.SecurityCamerasDirect.com

SECTION 6: KWEYE SMARTPHONE APP

— After downloading the app, attach your iPhone to your computer, sync the application to your phone.

6.1.2 Installing KWeye in Android

To install applications using Android Market perform the following steps:

— With your Android phone, go to the Applications menu and open Android Market. — Search for the application kweye — When the application is found, click on the KWeye icon to display details of the app. — To install KWeye, click Install and follow the on-screen instructions.

6.2 Set up access to a DVR

Usage and functionality of the KWeye app is the same on both iPhone and Android phones. However, the screens vary slightly between the two systems. To use KWeye:

• Tap the KWeye icon to open the app. The KWeye splash screen will appear.

(NOTE: The following images were captured from an Android smartphone. iPhone screens are functionally identical.)

Settings

iPhone KWeye Initial Screen

Android KWeye Initial Screen

514-Camera H.264 Security System Setup Guide

SECTION 6: KWEYE SMARTPHONE APP

• Tap the Settings icon. The splash screen will change to the Settings

screen.

• In the Device Info elds, enter the appropriate information for your

DVR:

— Address: IP address used to connect to your DVR modem from

the Internet, or the URL of the DynDNS server you use.

— Port: Mobile monitor server port number congured in the DVR’s

network mobile submenu. The default port number is 10510.

— DeviceName: A name you use to identify your DVR. — UserName and Password: Enter the username and password

you use to log into your DVR. NOTE: You may have to slide the screen up to display the UserName and Password elds.

• After completing the entries in the Settings menu, tap the Back button to test the settings and connect to your DVR. When

connecting to your DVR, the Device Info settings will be logged in the History screen for easy retrieval.

6.3 Using KWeye

• If KWeye is not running, tap the KWeye icon to open the app. The KWeye History screen will appear.

• In the History screen, tap the entry for the DVR you want to connect to open. The Settings screen will open.

• To use the Device Info in the Settings screen to access your DVR, tap the Back button in the upper left corner.

• Tap the Play button to start watching video from the DVR.

PTZ Controls:

Direction,

Zoom, Iris,

Focus

Play/Stop

Select Chann el

Switch Chann el Group

SW InformationSnapshot Set tings

www.SecurityCamerasDirect.com

• To view a particular camera, tap the Select Channel button for the camera channel. If you are connected to an 8- and

16-channel system and the channel button is not shown, tap a Switch Channel Group icon (next group,

, or previous

group

), to change the Select Channel buttons until the channel number is shown, then tap the button for the

channel.

• Rotate the phone 1/4 turn for a landscape view of the channel.

• To restore the app control buttons, orient the phone for a portrait view.

• To exit the application, press the smartphone Home or Back button.

SECTION 6: KWEYE SMARTPHONE APP

534-Camera H.264 Security System Setup Guide

SECTION 7: DVR SYSTEM MENUS

SECTION7

DVR System Menus

This section includes a detailed description of the DVR menu system. It is included for reference only.

7.1 Menu tree

Record

Tool Bar

Channel

Record

Bitrate

Resolution

Framerate

Packtime

Record Mode

Video

Channel

Name

Position

Live

Color

Record Time

Margin

Video Setup

Device ID

Password

Add Users

Change Password

Delete User

Set Permissions

Remote

View

Network

DDNS

Mobile

IP Address

Other Settings

Alarm

Duration

Buzzer

Prerecord

Exception

Motion

System Settings

Play

Manual Record

Keylock

Auto Sequence

Ezoom

VGA / BNC Switch

PIP 1x1

PIP 1x2

Language

Video System

Time

User

HDD

Maintenance

Information

System

www.SecurityCamerasDirect.com

SECTION 7: DVR SYSTEM MENUS

7.1.1 ToolBar

The Tool Bar provides icons for accessing menu features.

PIP 1x2

PIP 1x1

System Settings

EZoom

Play

Manual Record /

Stop Manual Record

VGA / BNC

Switch

Auto

Sequence

Keylock

Tool Bar

Tool bar icon functions:

System Settings: Opens the system conguration menu system.

Play: Search, playback and backup recorded les.

Manual Record / Stop Manual Record: Click to start or stop manual recording.

KEYLOCK: If the password is enabled, click “KEYLOCK” to logout of the system.

Auto Sequence: Click to enable auto-sequencing, the channels with images will be in sequence: channel 1, channel 2,

channel 3, channel 4, channel 1. Channels without images won’t appear in the sequence. To interrupt auto sequencing, press any button or click the mouse while in auto sequence mode.

EZoom: Click to enter zoom mode, and then click left key and drag to select the area that you want to magnify. Right click to exit.

VGA/BNC Switch: Click to switch the video output of the DVR from VGA to BNC or BNC to VGA.

PIP 1x1: This feature displays a small picture in a full screen.

PIP 1x2: This feature displays two small pictures in a full screen.

7.1.2 Menuoptions

To modify/adjust system conguration, click the System Settings icon on the Tool Menu.

554-Camera H.264 Security System Setup Guide

SECTION 7: DVR SYSTEM MENUS

Clicking the System Settings icon opens a window with 5 tabs: System, Record, Video, Network, and Alarm. These tabs provide general system settings for operating your DVR.

Open Drop-down List or Switch Value

Save Button

Titles of the menu list items are located on the left, and the corresponding changeable or non-changeable values are represented in the elds to the right. You can:

• Select the values from the list (toggling the preset data by pressing the arrows on the side of the eld);

• Select the values from the drop-down list (open the drop-down list by clicking the down arrows on the side of the eld);

• Input the required data after entering a customized window by pressing the [>>] button in some of the elds;

• Familiarize yourself with the existing non-changeable settings.

When entering data into the elds using the remote control directional keys or the DVR front panel, and when positioning the mouse over them, a short description of the setting will appear at the bottom of the window.

Several tabs have options that are spread across more than one window. You can move from window to window by pressing the “>>” button.

7.2 System menu

The System menu (see above) contains parameters for setting the basic conguration of your system. it includes the following options:

7.2.1 Language

Use this option to change the language of the DVR menu text and the On-Screen Display.

www.SecurityCamerasDirect.com

SECTION 7: DVR SYSTEM MENUS

7.2.2 VideoSystem

Set the system output to the camera input (PAL or NTSC). Note: The device will restart when you modify the camera mode.

7.2.3 TimeSetup

Click Time [System settings -> System -> Time] to open the Time setup menu.

DATE: Set up system date using the number keypad.

DATE FORMAT: Click the down arrow to switch the date format. Options: YY-MM-DD, MM/DD/YY.

TIME FORMAT: Click the down arrow to switch the time format. Options: 12 HOURS to 24 HOURS.

TIME: Set up the system time using the number keypad on the remote control.

DST: Daylight saving time. ON means DST clock change is enabled. You can setup the start time and end time of DST. For

example, in the right gure above, the start time is at 02:00:00 Sunday of the rst week on January. Similarly, setup the end time.

Note: After changing settings, click the “check” (save) button in the lower right corner of the screen.

7.2.4 Usermanagement

Click User [System settings -> System -> User] to open the user management setup menu. This menu allows user to set the device ID for the DVR and to change the system password. After turning on password and clicking the “check” button in the lower right corner of the window, exit the system and login again to manage other users.

574-Camera H.264 Security System Setup Guide

SECTION 7: DVR SYSTEM MENUS

DEVICE ID: Set Number to identify device. The default name is “000000”

PASSWORD: Change the password. The following settings can be congured only by a user with administrative privileges.

ADD USERS: To add new user, enter a new username and password. Password must be entered in both the Password

and Conrm Password elds. Password cannot exceed 6 digits.

CHANGE PASSWORD: Select the username whose password you want to change, then enter the old password, the new password, and the new password again in the Conrm Password eld.

DELETE USER: In this window, select the user you want to delete, then click the “check” button in the lower right corner of the window.

SET PERMISSION: For each user, set the permissions for use of the system. Permissions include: Auto sequence, Manual REC, Playback/Backup, Ezoom, PIP, Update/Reboot/Maintenance/Format/Default, etc.

www.SecurityCamerasDirect.com

SECTION 7: DVR SYSTEM MENUS

REMOTE PERMISSION: This feature must be setup if operating the system remotely. Only users with admin privileges can set other user’s remote permissions. These permissions include: Record/Capture, Playback/Download, and Setting. If password verication is enabled (marked ON, i.e. you must login with a password) you can setup seven user passwords and an administrator password.

Note: When Password is enabled, login to the system as an admin to manage user settings. The administrator’s name (Admin) cannot be changed. Initially, two users exist: Admin and User1. The default password for Admin is “888888” and the default password for User1 is “666666”.

If forget your password, you can reset the password by shunting the pin of block J17 on main board for 5 seconds while the system is running. However, REMOVING THE COVER OF YOUR DVR WILL VOID THE WARRANTY.

7.2.5 HDD

Click HDD [System settings -> System -> HDD] to open the HDD (hard disk drive) management menu.

594-Camera H.264 Security System Setup Guide

SECTION 7: DVR SYSTEM MENUS

STATE: The HDD can have one of three possible “states”: OK, un-format, and No Disk. If the HDD cannot operate normally (un-format or No Disk), an icon will be displayed on video live view window. If a new HDD is used by the DVR for the rst time, the system will restart after the HDD is formatted.

TOTAL/FREE: Indicates total space available on the HDD.

FREE TIME: Indicates remaining recording time of the HDD.

OVERWRITE: Includes: CLOSE, AUTO, 1 HOUR, 3 HOURS, 1 DAY, 2 DAYS, 7 DAYS, 30 DAYS and 90 DAYS:

CLOSE: the recording stops when the hard disk drive is full. It will continue recording if “overwrite” is enabled. AUTO: the recording continues and overwrites previous recordings when hard disk drive space is full. 2 DAYS: a recordings remains on the HDD for two days at most. After two days, a recording may be overwritten. Other options: Similar to the 2 DAY option.

FORMAT HDD: Move the cursor to select the device, then press HDD to start formatting.

FORMAT USB: This function allows you to format a USB storage device.

7.2.6 Maintenance

Click Maintenance [System settings -> System -> Maintenance] to open the Maintenance setup menu.

www.SecurityCamerasDirect.com

SECTION 7: DVR SYSTEM MENUS

SYSTEM UPDATE: To perform a system update:

1. Insert a thumb drive into a Windows PC USB port, then.

a. Format the thumb drive for a FAT32 le system.

b. Create a root directory on a thumb drive named “dvrupgrade”.

c. Copy the update le to the “dvrupgrade” directory.

d. Eject the thumb drive from the Windows PC.

2. Insert the thumb drive into a USB port on the DVR, then:

a. Click the >> icon on the SYSTEM UPDATE line.

b. Wait until the DVR recognizes the thumb drive.

c. Press Enter to upgrade the rmware. The progress of the system upgrade will be displayed. After completing the

upgrade, the DVR will restart. NOTE: The system upgrade usually requires more than two minutes to complete.

LOAD DEFAULT: Restores all the system conguration to the factory settings.

REBOOT: Use this function to restart the DVR.

POWER OFF: Use this function to power o the DVR.

AUTO MAINTAIN: When AUTO MAINTAIN is ON, you can set a time for system to perform a restart.

614-Camera H.264 Security System Setup Guide

SECTION 7: DVR SYSTEM MENUS

7.2.7 Information

Click Information [System settings -> System -> Information] to open the Information display. This display includes: device type, software version, release date, import parameter and export parameter.

Use Export Parameter to save that information to a USB disk. Parameter information must be exported before it can be imported (restored).

7.3 Record

To open the Record menu, move the cursor to RECORD (the icon will be highlighted when selected), then press Enter. You can use the direction keys and cursor to change the options.

www.SecurityCamerasDirect.com

SECTION 7: DVR SYSTEM MENUS

7.3.1 RecordChannel

With this option you can select the camera (channel) number whose settings you want to modify. If you want the changes to apply to all available channels, select “All”. Make the selection by pressing the arrow buttons; the options include CH1, CH2, CH3, CH4 and ALL.

7.3.2 Record

Record ENABLE indicates that the channel is enabled for recording.

7.3.3 Bit-rate

There are three options: GOOD, NORMAL and LOW, corresponding to HIGHEST, HIGH and NORMAL data stream standard. The bit rate of each channel recorded can be adjusted independently.

7.3.4 Resolution

Record Resolution indicates the setup resolution and code rate for recording. There are three options: D1, HD1 and CIF resolution. The resolution of each channel recorded can be adjusted independently.

7.3.5 FrameRate

You can set the recording frame rate (frames per second, fps) for the current channel. The higher the record frame rate, the smoother the movement you will see in playback mode. The frame rate of each channel can be adjusted independently.

For PAL video output format, the default system resolution is CIF, and the default frame rate is 25 fps for each channel. With this setting, the system will record 100 fps with all channels. The frame rate can be set from 1 fps to 25 fps per channel.

For NTSC video output format, the default system resolution and frame rate is CIF @ 30 fps. With this setting, the system will record 120 fps with all channels. The frame rate can be set from 1 fps to 30 fps per channel.

7.3.6 Packtime

Record Pack Time is the time length of video segments saved during the backup of recorded video to an external device. There are four options: 15 min, 30 min, 45 min, and 60 min.

634-Camera H.264 Security System Setup Guide

SECTION 7: DVR SYSTEM MENUS

7.3.7 RecordMode

Record mode includes two general categories: ALWAYS and SCHEDULE.

ALWAYS: indicates that the DVR will record the channel selected continuously.

SCHEDULE: This setup allows you to create a weekly schedule for recording. This assures that only selected events are

recorded on the HDD. For example, you may set up the system to record continuously during business hours, record at lunch time only when an alarm is triggered, and record at night when motion is detected and/or an alarm is triggered.

NOTE: Manual recording continues until stopped by the operator. It overrides all settings.

CHANNEL: You can select all channels or just one channel. There are three modes for recording: ALARM, NORMAL and NO RECORD.

Dierent colors indicate dierent recording modes: Red indicates alarm record, green indicates normal record, gray indicates no recording.

To set up weekly schedules, click on the box of the recording mode you want (Alarm, Normal or No record), then click each box in the schedule time line that you want to apply the mode to. You can also left click and drag a frame over boxes in the schedule time line that you want to apply the mode to. You can use the [FROM-TO] pull-down menus and COPY button settings to repeat setting from one day to another day, or to all days.

After you setup the schedule, activate it by clicking the “check” button in the lower right corner of the window.

NOTE

When you select the ALARM option, it is necessary to set the motion detection sensitivity and area. Please refer to Motion Detect on page 72,for details. Congure the alarm triggering settings before selecting alarm recording.

To restore to default settings, scroll to the “back” button in the lower right corner of the window, then press ENTER.

To save the new settings, scroll to the “check” button in the lower right corner of the window, then press ENTER.

www.SecurityCamerasDirect.com

SECTION 7: DVR SYSTEM MENUS

7.4 Video

Move the cursor to VIDEO (the icon will be highlighted when selected), then press ENTER to enter the video menu. You can use the direction keys and cursor to change the options.

7.4.1 VideoChannel

Select the channel to setup.

7.4.2 Name

You can assign a name to each channel. The channel name can be up to 9 characters in length.

7.4.3 Position

You can set the position where the channel name appears in the view window. Press ENTER to switch from U-L, D-L, U-R, D-R and OFF.

7.4.4 Live

Set to ON to view the channel in live mode; set to OFF to disable live viewing.

7.4.5 Color

Click Color [System settings -> Video -> Color ] to open the video color adjustment display. With this feature, you can adjust camera color attributes for the best image rendition. By default, the values are set to a midpoint (31).

654-Camera H.264 Security System Setup Guide

SECTION 7: DVR SYSTEM MENUS

Press u / t key or drag the set bar to adjust the video attributes. Clicking DEFAULT button to reset the color parameter values, click the “check:” button to save your settings.

7.4.6 RecordTime

You can dene which information will be recorded onto the video as the OSD (On-Screen Display) string.

7.4.7 Margin

Click Margin [System settings -> Video -> Margin] to open the video margin setup menu. You can creation a margin (frame) around the video screen using this option. Margins compress the video image. No area of the video image is obscured.

7.4.8 VideoSetup

Click Video Setup [System settings -> Video -> Video Setup] to open video setup menu.

www.SecurityCamerasDirect.com

SECTION 7: DVR SYSTEM MENUS

VGA (display resolution): Options include 1024 x 768 (XGA) and 1280 x 1024 (SXGA).

NOTE

The DVR will restart if the display resolution is changed.

Sequential Time (SEC): This sets the pause time when auto-sequence is enabled. Value: 1 – 300 seconds.

Channel: Select the channel to setup for privacy. Privacy areas are congured through the Area Covered options.

Area Covered: Set privacy area. Up to four areas of privacy can be congured for each channel. Privacy areas appear as black

rectangles over portions of the video image that are setup as “private.”

7.5 Network

Move the cursor to NETWORK (the icon will be highlighted when selected), and press ENTER to open the Network conguration window. In this window, you can congure network, DDNS, email, and mobile access settings.

NOTE

The default IP addresses and port settings of your DVR may be dierent from those shown in this document. Always use network settings that are compatible with your network(s).

7.5.1 NetworkSetup

After selecting network mode, static, DHCP, or PPPOE allocation, and setup the web port, you can access the DVR remotely across the internet.

STATIC network settings

When selecting STATIC allocation, you must enter the IP address, subnet mask, gateway, and a web port.

674-Camera H.264 Security System Setup Guide

SECTION 7: DVR SYSTEM MENUS

UPnP: Universal plug and play. If it is OFF, you must map its port to get a mapped IP address; if it is ON, it will map the DVR ports automatically. NOTE: Enable UPnP on your router before you enable UPnP on the DVR.

MEDIA PORT: Port used to transfer video data from the DVR to a client.

WEB PORT: Sets up the port for the IE browser via HTTP. The default web port is 80.

SETUP PORT: This port number is xed at 8000. It cannot be changed.

DNS: Press ENTER, then enter the domain name sever address.

IP ADDRESS: Press ENTER, then enter the IP address.

SUBNET MASK: Press ENTER, then enter the subnet mask.

GATEWAY: Press ENTER, then enter the gateway address.

PPPOE network settings

When selecting PPPOE, enter the PPPOE USER and PASSWORD provided by your ISP.

www.SecurityCamerasDirect.com

SECTION 7: DVR SYSTEM MENUS

MEDIA PORT: Port for private protocol between the DVR and a client PC. The default is 9000. If this port is used by the computer for other communications, change the default value to an unused port.

WEB PORT: Sets up the port for the IE browser via HTTP. If this port number is changed, append the port number to the IP address when connecting to PC to the DVR. For example, the WEB port is changed to 8088 and the DVR IP address is

192.168.15.145, the URL for the DVR (across the same subnet) is http://192.168.15.145:8088.

SETUP PORT: This port is xed and cannot be changed. It is set to 8000.

MAC ADDRESS: The hardware address of the network interface circuitry. This address xed and cannot be changed.

PPPOE user and password: Enter the PPPOE username and password provided by your internet service. Click the “check”

button in the lower right corner of the window to reboot the DVR. After rebooting, the device will save it and set PPPOE as default network type. The IP address will be congured as a dynamic IP address.

DHCP network settings

When selecting DHCP, the DHCP server will assign the DVR IP address and other network settings. When you select DHCP and save your conguration, the DVR will connect to the DHCP server and acquire its network settings.

7.5.2 DDNSSetup

Move the cursor to DDNS SETUP and press ENTER to open the DDNS Setup menu.

694-Camera H.264 Security System Setup Guide

SECTION 7: DVR SYSTEM MENUS

DDNS: Select either ON and OFF. If a DDNS server is available, select ON.

SERVER: Select one of the three providers: 3322, dyndns, or perfecteyes.

HOST NAME: Enter the name of the host server.

USER NAME: Enter the name of the user establishing the DDNS server account.

PASSWORD: Enter the password associated with the USER NAME.

7.5.3 EmailSetup

Move the cursor to EMAIL SETUP and press ENTER to open the Email Setup menu.

www.SecurityCamerasDirect.com

SECTION 7: DVR SYSTEM MENUS

SSL: SSL is a security link transport protocol. You can encrypt your email messages with SSL to prevent hackers from monitoring your communication information and your password. Set SSL to OPEN if using a Gmail.com server, and set it to CLOSE if using another mail server. If the settings you chose do not work, contact your mailbox website where to get an SMTP server and SSL for the mail box.

Interval: This indicates the time interval for sending email. Options are 5 sec, 10 sec, 30 sec, 1 min, and 3 min.

SMTP Port: This indicates the SMTP server sender port. Usually, the SMTP port is 25, but there are exceptions. For example, the

SMTP port of the Gmail server should be 465.

SMTP: This indicates SMTP server address.

Sender: Sender indicates sender’s email address. The email address should be consistent with the server you use. For example,

when you use the email address “abc@gmail.com”, the corresponding server should be smtp.gmail.com.

Receiver: This indicates the recipient email address. The email address is used to receive images transmitted after a motion detection alarm by the DVR.

7.5.4 MobileMonitor

Move the cursor to MOBILE, then press ENTER to open the mobile monitor menu.

SERVER PORT: Mobile monitoring port. Enter the correct mobile port, then click the “check” button in the lower right corner of the

window to commit your settings. The setting range is 1024 – 65535. The default value is 10510.

NETWORK TYPE: Select on of the following options: 3G, 2.5G, 2.75G, and WIFI, then click the “check” button in the lower right corner of the window to commit your settings.

714-Camera H.264 Security System Setup Guide

SECTION 7: DVR SYSTEM MENUS

Connect the DVR to the Internet before setting the DVR port number. The port number cannot be the same as the ports specied in other network menus.

NOTE

You can only view one camera channel at a time from a mobile phone. The speed of the display depends on the speed of the internet connection

7.6 Alarm

Move the cursor to ALARM and press ENTER to open the alarm menu.

7.6.1 DURATION

This function sets the duration of the recording time when alarm recording is activated. Options are 30 sec, 1 min, 2 min and 5min.

7.6.2 BUZZER

This function sets the buzzer calling time when the alarm is triggered. Options are OFF, 5 sec, 10 sec, 30 sec, and 60 sec.

7.6.3 PRERECORD

Prerecord sets the time segment recorded before the alarm is activated. Options are OFF and 5 sec.

7.6.4 EXCEPTION

Click Tool Bar -> System settings -> Alarm -> Exception to open the exception alarm menu. In this menu you can set the buzzer and I/O output for HDD Full, HDD Loss and Video Loss.

www.SecurityCamerasDirect.com

SECTION 7: DVR SYSTEM MENUS

HDD FULL: You can set buzzer alarm and I/O output alarm when there is a dened space remaining for HDD to recording. Options are OFF, 1G, 5G , 10G, 1 hr, 5 hrs , 10 hr and 20 hr .

HDD LOSS: ON causes the relevant alarm to occur when there is no HDD installed. An alert icon will be displayed on the left bottom of channel 1 in the live view.

VIDEO LOSS: ON causes the relevant alarm to occur when a channel has no video input.

NOTE

If the buzzer alarm is OFF, exception alarms will not be triggered.

7.6.5 MotionDetection

Click Tool Bar -> System settings -> Alarm -> Motion to open the motion detection menu. In this menu, you can set the Sensitivity, MD Detection area, Output, Record, Buzzer, Prerecord, and Email parameters.

734-Camera H.264 Security System Setup Guide

SECTION 7: DVR SYSTEM MENUS

CHANNEL: Select the channel you need to setup. Open the drop-down menu to select the channel number

SWITCH: Set the switch to ON to enable motion detection for the channel selected.

SENSITIVITY: Set the sensitivity for the channel selected. A sensitivity of “1” indicates highest sensitivity. Open the drop-down list

to select a level appropriate for the channel.

MD AREA: To improve DVR performance, use the MD Area feature to select only the areas of a channel video image to sense for motion. For example, the image of a road near a walkway can be congured to sense for motion only in the walkway only.

To establish motion detection areas in the video image, click the >> icon on the MD AREA line. An image of the channel video will appear, covered by a semi-transparent layer on a 10 x 15 block grid. Motion sensing for blocks in the grid can be toggled on and o by clicking on the block area. Areas on the screen selected for motion sensing are indicated by removal of the semi-transparent layer inside the block area.

Video channel without (left) and with (right) areas of motion sensing

To return to the MOTION DETECTION menu from the MD AREA setup screen, right-click anywhere.

RECORD: If set to ON and the channel is triggered by motion, the channel will record.

BUZZER: If set to ON and the channel is triggered by motion, the buzzer will sound. NOTE: This feature is not used in this DVR.

PRERECORD: If set to ON and the channel is triggered by motion, the previous 5 seconds of video from the channel is recorded.

EMAIL: If set to ON and the channel is triggered by motion, a picture of the channel will be send with the email notication.

www.SecurityCamerasDirect.com

SECTION 8: CLEANING

SECTION8

Cleaning

Clean the camera lens and IR lamp shield with a mild glass cleaning solution and a lint free cloth.

• Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing. These may cause damage to

the surface over time.

• Dust can be removed from equipment by wiping it with a soft damp cloth. To remove stains, gently rub the surface with a soft

cloth moistened with a mild detergent solution, then rinse and dry it with a soft cloth.

CAUTION



Do not use benzene, thinner or other chemical products on the camera assembly; these may dissolve the paint and promote damage of the surfaces. Before using any chemical product, read the instructions carefully.

754-Camera H.264 Security System Setup Guide

APPENDIX A: OFF-LOADED VIDEO FILES

APPENDIXA

O-loaded Video Files

Video les can be o-loaded to a USB thumb drive or downloaded using IE. For the best compatibility and performance with Windows operating systems, Security Cameras Direct recommends that you choose MPEG4 le format for all video backups and downloads.

Backing up les to a USB thumb drive

When video les are backed up to a USB thumb drive in MPEG 4 format, the DVR also copies the MPEG4 CODEC to the drive. Before playing these les on a Windows operating system with an application such as Windows Media Player, the CODEC must be installed. The CODEC is provided in ZIP format.

To install the CODEC:

1. Copy the CODEC from your thumb drive to your Windows computer. It is named WMP_Media_Filter.

2. Extract the CODEC to new folder.

3. Open the folder and run the InstallFilter executable.

When playing an MP4 le with Windows Media Player for the rst time, you may be prompted to allow that le extension to be used. Click OK to proceed.

Downloading video les

When downloading video les with the IE web browser, the MPEG4 CODEC pack is not included. If the CODEC is not already installed on your computer, contact the Security Cameras Direct Support team at 1.800.316.6027 to obtain it.

www.SecurityCamerasDirect.com

APPENDIX B: SPECIFICATIONS

APPENDIXB

Specications

Feature Specication

Video F ormat NTSC

Video Compression H.264 B aseline Compression

Video Input / Ou tput BNC 4 Input / 1 Output

Alarm Type Motion detec tion, Senso r Input, Relay Ou tput , Video Loss

Display Frame Rate Each Chann el, 30 FPS

Playback Resolution CIF/Half- D1/D1 @ Recorded frame rate

Record Frame Rate 120 FPS @ CIF, 120 FPS @ HD1, 60 FPS @ D1.

Record metho d Power-on Auto R ecord, Scheduled Re cord (Normal Record, M otion Detec tion, Sensor Trigger), Manual Reco rd

HDD Interface SATA Interface suppor t up to 1000GB, HDD*1

Network Protocol TCP-IP/ DHCP/DDNS/PPPOE/ Email

Network Function Live Monitor, Playback, Conguration, Backup, Mobile Phone Surveillance

USB 2.0 Interface Mouse / Por table Mobile HDD/ USB thumb drive/ DVD Burner/ Firmware Upgrade

Playback method Normal, Fast Fo rward, Slow Forward, Rewind, Single Step

Network Interf ace RJ- 45 10/100BaseT Ethernet Auto Detect

Area Cover ed E ach channel supports four pieces of area covered

Video B ackup AVI over Network

Power Adapter DC 12V Adapter

Power consumption 10 ~ 15W

Operating temperature 50° F ~ 104° F (10°C ~40° C)

Operating humidit y 10%~90%

Dimensions 9.84 in ( W) x 8.58 in (D) x 1.65 in (H) in (250 mm (W) x 218 mm (D) x 42 mm (H))

Security Cameras Direct ECO4IR, ECO4LCD Quick Installation And Setup Manual

Specifications and Main Features

Frequently Asked Questions

User Manual