HD Vandal Proof IP Dome Camera User’s Manual
Version 3.5.0
i
Welcome
Thank you for purchasing our IP camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!
ii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series IP camera should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding holes of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
iii
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name Amount
IPC Unit 1
Accessories bag 1
Quick Start Guide 1
CD 1
iv
Table of Contents
1 General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
1.3 Specifications................................................................................................................2
1.3.1 Performance...........................................................................................................2
1.3.2 Factory Default Setup...........................................................................................3
2 Structure ....................................................................................................................................11
2.1 Multiple-function Combination Cable ......................................................................11
2.2 Framework and Dimension.......................................................................................12
2.3 Bidirectional talk .........................................................................................................13
2.3.1 Device Connection ..............................................................................................13
2.3.2 Operation ..............................................................................................................13
2.4 Alarm Setup.................................................................................................................13
3 Installation .................................................................................................................................15
3.1 Device Installation ......................................................................................................15
3.2 SD Card Installation ...................................................................................................18
3.3 Lens Adjustment.........................................................................................................18
4 Quick Configuration Tool.........................................................................................................20
4.1 Overview......................................................................................................................20
4.2 Operation .....................................................................................................................20
5 Web Operation..........................................................................................................................23
5.1 Network Connection...................................................................................................23
5.2 Login and Main Interface...........................................................................................23
v
6 FAQ ............................................................................................................................................26
Appendix Toxic or Hazardous Materials or Elements ...............................................................27
1
1 General Introduction
1.1 Overview
This series IP camera integrates the traditional camera and network video technology. It adopts audio
and video data collection, transmission together. It can connect to the network directly without any
auxiliary device.
This series IPC uses standard H.264 video compression technology and G.711a audio compression
technology, which maximally guarantee the audio and video quality.
This series IPC enclosure has the strong resistance capacity, which can guarantee the proper work
performance under heavy strike. It supports real-time monitor and listening at the same time. It supports
analog video output and dual-way bidirectional talk.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the network
and then use a network client-end. Due to its multiple functions and various uses, this series IPC is
widely used in many environments such office, bank, road monitor and etc.
1.2 Features
User
Management
z Different user rights for each group, one user belongs to one group.
z The user right shall not exceed the group right.
Storage
Function
z Support central server backup function in accordance with your configuration and
setup in alarm or schedule setting
z Support record via Web and the recorded file are storage in the client-end PC.
z Support built-in SD card.
z Support local SD card hot swap, support short-time storage when encounter
disconnection.
Alarm
Function
z Real-time respond to external local alarm input and video detect as user pre-
defined activation setup and exert corresponding message in screen and audio
prompt(allow user to pre-record audio file)
z Real-time video detect: motion detect, camera masking.
z Can generate an alarm when network abnormal, SD card abnormal event
occurred.
Network
Monitor
z IPC supports one-channel audio/video data transmit to network terminal and
then decode. Delay is within 270ms (network bandwidth support needed)
z Max supports 20 connections.
z Adopt the following audio and video transmission protocol: HTTP, TCP, UDP,
MULTICAST, RTP/RTCP, RTSP and etc.
z Support web access, widely used in WAN.
Network
Management
z Realize IPC configuration and management via Ethernet.
z Support device management via web or client-end.
z Support various network protocols.
Peripheral
Equipment
z Support the on-off alarm device to alarm via the sound or the light.
Power
z External power adapter DC12V/AC 24V
z Support PoE.
Assistant
Function
z Log function
z Support PAL/NTSC
z Support system resource information and running status real-time display.
2
z Day/Night mode auto switch (ICR switch).
z Built-in IR light. Support IR night vision (For HDBW Series only).
z Backlight compensation: screen auto split to realize backlight compensation to
adjust the bright.
z Support electronic shutter and gain setup.
z Support video watermark function to avoid vicious video modification.
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for IPC performance specification.
Model
Parameter
IP9'(/03,5 Series
Main
Processor
TI Davinci high performance DSP
OS Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the same
time.
User Interface Remote operation interface such as WEB, DSS, PSS
System
System Status SD card status, bit stream statistics, log, and software version.
Image Sensor 1/2.8-inch CMOS
Pixel
2048（H）*1536（V）
Day/Night
Mode
Support day/night mode switch and IR-CUT at the same time.
Auto Iris DC drive
Gain Control Fixed/Auto
White Balance Manual/Auto
BLC Manual/Auto
Electronic
Shutter
Manual/Auto
PAL: It ranges from 1/3 to 1/10000.
NTSC: It ranges from 1/4 to 1/10000.
Manual/Auto
PAL: It ranges from 1/3 to
1/100000.
NTSC: It ranges from 1/4 to
1/100000.
Video
Compression
Standard
H.264/H.264B/MJPEG
Video Frame
Rate
PAL:
Main stream（2048*1536@15fps）
extra stream,（704*576@15fps）
Main stream（1920*1080@25fps）
extra stream（704*576@25fps）
NTSC:
Main stream（2048*1536@15fps）
extra stream（704×480@15fps）
Main stream（1920*1080@30fps）
extra stream（704×480@30fps）
Video Bit Rate
H.264: 56Kbps-8192Kbps.
ＭJPEG is adjustable and bit rate is adjustable.
Support customized setup.
Video Flip
Support mirror.
Support flip function.
Video Parameter
Snapshot Max 1f/s snapshot. File extension name is JPEG.
3
Privacy Mask Supports max 4 privacy mask zones
Video Setup Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, privacy mask.
Lens
3.3-12mm@F1.4
Lens Interface CS. Lens is the default accessories
Audio Input
1-channel，RCA audio input.
Audio Output
1-channel, RCA, audio output.
Bidirectional
Talk Input
Reuse the first audio input channel
Audio Bit Rate 16kbps 16bit
Audio
Audio
Compression
Standard
G.711A/G.711Mu/PCM
Motion Detect
396 (18*22) detection zones；sensitivity level ranges from 1 to 6 (The 6th
level has the highest sensitivity)
Activation event, alarm device, audio/video storage, image snapshot, log,
email function and etc.
Video
Video Loss
Activation event, alarm device, audio/video storage, image snapshot, log,
email function and etc.
Alarm Input
2-channel input，1-channel output
Record
Priority
Manual>External alarm >Video detect>Schedule
Record
and
Backup
Local Storage
Support Micro SD card storage
Wire Network 1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network
Protocol
Standard HTTP, TCP/IP, IPv4/IPv6, ARP, IGMP, ICMP, RTSP, RTP, UDP,
SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour, SNMP,
NFS.
Network
Remote
Operation
Monitor, system setup, file download, log information, maintenance ,
upgrade and etc
Video Output
1-channel analog video output，BNC port, 9-pin port connection
Reset 6-pin port connection
AUX
Interface
IR light 35 LED, IR distance 10 to 20 meters (For HDBW series product only)
Power Support AC24V/DC12V power. PoE
Power
Consumption
General series: below 7W.
IR series: below 13W.
General series: below 14W.
IR series: below 16W.
Working
Temperature
-10℃~+60℃
Working
Humidify
10%~90%
Dimensions(m
m)
¢160x118.5
Weight 1.25g
General Parameter
Installation
Support various installation modes（Enclosure and bracket is optional）
1.3.2 Factory Default Setup
Please refer to the following sheet for factory default setup information.
4
Default setup
Function
Setup Type
Item
IP9'-(/03,5
Series
Brightness 50
Contrast 50
Hue 50
Saturation 50
Exposure mode Auto
Gain Scope 0~80
Auto Iris ON
Profile Auto
Day&Night Auto
Backlight Off
Mirror Off
Conditions
Flip No flip Flip 180°
Bit stream
type
General
Encode
mode
H.264B
Resolution
1080P
（1920*1080）
720P(1280*72
0)
Frame rate
（FPS）
PAL: 25
NTSC:30
Bit stream
type
CBR
Reference bit
rate
3584-8192 Kb/S 1536-8192Kb/S
Bit rate 8192
I frame
interval
50
Watermark
settings
Enable
Main
stream
Watermark
character
DigitalCCTV
Enable Enable
Bit stream
type
General
Encode
mode
H.264B
Resolution
CIF(352×288/35
2×240)
CIF(352×288/3
52×240)
Frame rate
（FPS）
PAL: 25
NTSC:30
Camera Setup
Video
Video bit
stream
Extra
stream
Bit rate type CBR
5
Default setup
Function
Setup Type
Item
IP9'-(/03,5
Series
Reference bit
rate
192-1024Kb/S
Bit rate 1024
I frame
interval
50
Snap type General snap
Image size
1080P
（1920*1080）
720P(1280*7
20)
Quality Better
Snapshot
Interval 7s
Privacy mask Enable
Channel title Enable
Overlay
Time title Enable
Snapshot
path
C:\PictureDownload
Path
Record path C:\RecordDownload
Enable Enable
Main stream
Encode
mode
G.711A
Enable Disable
Audio
Sub(Extra) stream
Encode
mode
G.711A
Host name IPC
Ethernet card Wire(Default)
Mode Static
MAC
address
Depends on the device
IP version IPV4
IP address 192.168.1.18 RU'+&3
Subnet mask 255.255.255.0
Default
gateway
192.168.1.1
Preferred
DNS
8.8.8.8
Alternate
DNS
8.8.8.8
Network setup
TCP/IP
Enable
ARP/Pingto
to set IP
address
service
Enable
6
Default setup
Function
Setup Type
Item
IPVD-EL3MPIR
Series
Max
connection
10
TCP port 37777
UDP port 37778
HTTP port 80
RTSP port 554
HTTPs
Enable
Disable
Connection
HTTPs port 443
Enable Disable
User name N/A
PPPoE
Password N/A
Server type Disable ，CN99 DDNS
Server IP none
Port 80
Domain
name
none
User name none
Password N/A
DDNS
Update
period
10m
IP filter Trusted sites Disable
SMTP server none
Port 25
Anonymity Disable
User name anonymity
Password N/A
Sender none
Authenticatio
n (Encrypt
mode)
N/A
Title
(Subject)
IPC Message
Attachment
Enable
Main
Receiver
N/A
Interval 0s
SMTP（email）
Health email Disable ，interval=60m
UPnP Enable UPnP Disable
SNMP SNMP v1 Disable
7
Default setup
Function
Setup Type
Item
IPVD-EL3MPIR
Series
SNMP v2 Disable
SNMP port 161
Read
community
public
Write
community
private
Trap address N/A
Trap port 162
Enable Enable
Bonjour
Server name
“Device SN”.
Depends on the device.
Multicast
address
239.255.42.42
Multicast
Port 36666
WIFI On(Enable) Enable
Real-time
monitor
0
Wireless
QoS
Parameter
Disable
QoS
Command 0
Enable Disable
Anti-dither 5 seconds
Sensitivity 3
Record
Channel
Enable
Record
Delay
10 seconds
Relay
(Alarm)
output
Enable
Alarm delay 10s
Send email Disable
Motion detect
Snapshot Disable
Enable Disable
Record
Channel
Enable
Record
Delay
10 seconds
Relay out Enable
Record
Delay
10 seconds
Event
management
Video detect
Video (Camera) masking
Send email Disable
8
Default setup
Function
Setup Type
Item
IPVD-EL3MPIR
Series
Snapshot Disable
Enable Disable
Relay input Alarm1
Anti-dither 0s
Sensor type NO
Record
channel
Enable
Record delay 10s
Relay
(Alarm)
output
Enable
Relay
(Alarm) delay
10s
Send email Disable
Relay (Alarm) activation
Snapshot Disable
Alarm setup
Relay (Alarm) output 1
Enable Disable
Relay
(Alarm)
output
Enable
Relay output
delay
10s
No SD card
Send email Disable
Enable Disable
Capacity limit
(Space
threshold)
10%
Relay
(Alarm)
output
Enable
Relay output
delay
10s
Capacity warning
Send email Disable
Enable Disable
Relay
(Alarm)
output
Enable
Relay output
delay
10s
SD card error
Send email Disable
Enable Disable
Abnormity
Disc
onn
ecti
on
Record Enable
9
Default setup
Function
Setup Type
Item
IPVD-EL3MPIR
Series
Record delay
10s
Relay
(Alarm)
output
Enable
Relay output
delay
10s
Enable Disable
Record Enable
Record delay 10s
Relay
(Alarm)
output
Enable
IP conflict
Relay output
delay
10s
FTP enable Disable
Server IP N/A
Port 21
User name anonymous
Password N/A
Remote
storage path
share
Destination(Storag
e )
FTP
Emergency
storage to
local path
Disable
Pack
duration
8m
Pre-record 5s
Disk full Overwrite
Record mode Auto
Storage
management
Conditions (Record
control)
Record
Stream
Main Stream
Device name
Device SN.
Depends on the device.
Language English
Local setup
Video
standard
NTSC NTSC
Date format Y-M-D
Time format 24H
Time zone GMT+08:00
Current time Sync PC
System
management
General setup
Date and time
DST Disable
10
Default setup
Function
Setup Type
Item
IPVD-EL3MPIR
Series
DTS type Week
Start time
00:00:00 of the first Sunday of the
month
End time
00:00:00 of the second Monday of
the month
Synchronize
with NTP
Disable
NTP server clock.isc.org
Port 37
Update
period
10m
Auto reboot Enable 02:00 each day
Auto maintenance
Auto delete
old files
Disable
11
2 Structure
2.1 Multiple-function Combination Cable
You can refer to the following figure for multiple-function combination cable information. See Figure 2-1.
Figure 2-1
Please refer to the following sheet for detailed information.
Port Name Function Connection Note
VIDEO OUT
Video output
port
BNC
Output analog video signal. It can connect to the
TV monitor to view the video.
AUDIO IN
Audio input
port
RCA
Input audio signal. It can receive the analog audio
signal from the pickup.
AUDIO OUT
Audio output
port
RCA
Output audio signal to the devices such as the
sound box.
LAN Network port
Ethernet
port
z Connect to standard Ethernet cable.
z Support PoE.
I/O I/O port / Includes alarm input and output.
RESET Reset button /
The reset button is to restore device factory default
setup.
POWER
Power input
port
/
Power port. Input DC 12V or AC 24V power.
Please connect the DC5.5 round port to 2-pin
converter cable when you are using AC 24V
power.
12
Please refer to the follow sheet for detailed pin information.
Port Name SN Name Note
1 ALARM_COM Alarm output public port.
2 ALARM_NO
Alarm output port. It is to output the alarm signal to the
alarm device.
NO: normal open alarm output port.
3 ALARM_IN1
Alarm input port 1. It is to receive the on-off signal from
the external alarm source.
4 ALARM_IN2
Alarm input port 2. It is to receive the on-off signal from
the external alarm source.
I/O Port
5 GND Ground port
2.2 Framework and Dimension
Please refer to the following two figures for dimension information. The unit is mm. See Figure 2-2 and
Figure 2-3.
Figure 2-2
13
Figure 2-3
2.3 Bidirectional talk
2.3.1 Device Connection
Before the operation, connect the active pickup to the audio input port of the device. Connect the active
speaker to the audio output port of the device. Please make sure the client-end device has the audio
input and output function. For example, you need to connect the microphone and then earphone to the
PC if you want to implement the bidirectional talk function.
2.3.2 Operation
Login the Web and click the bidirectional talk button to enable this function. Click this button again; you
can close current bidirectional talk.
2.4 Alarm Setup
The alarm interface is shown as in Figure 2-4. Please follow the steps listed below for local alarm input
and output connection.
1) Connect the alarm input device to the alarm input port (No.3 pin or No.4 pin) of the I/O cable.
2) Connect the alarm output device to the alarm output port (No.2 pin) and alarm output public port (No.1
pin). The alarm output port supports NO (normal open) alarm device only.
3) Open the Web, go to the Figure 2-4. Please set the alarm input 01 port for the first channel of the I/O
cable (No.3 pin). The alarm input 02 is for the 2
nd
channel of I/O cable (No.4 pin). Then you can select
the corresponding type (NO/NC.)
4) Set the WEB alarm output. The alarm output 01 is for the alarm output port of the device. It is the
No.2 pin of the I/O cable.
14
Figure 2-4
15
3 Installation
This series IPC can be put on the table to realize surveillance. Or you can use the bracket or the in-
ceiling installation to realize the hang function. Please refer to the steps listed below.
3.1 Device Installation
Step 1
Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome cover
and then open the cover. The device is shown as in Figure 3-1
Figure 3-1
Step 2
Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome and
then remove the device pedestal. See Figure 3-2 .
With IR light Without IR light
Figure 3-2
16
Step 3
Draw out the cable exit and four screw holes in the installation position according to the device pedestal.
Dig the four plastic expansion bolt holes and cable exit. Insert the four plastic expansion bolts into the
screw holes
Step 4
Adjust the camera pedestal to the proper position and then draw the cable through the cable exit you
just dug in the ceiling (wall). Line up the four screw holes in the device pedestal to the four plastic
expansion bolt holes in the installation position. Put the four self-tapping screws in the device pedestal
and then use the screwdriver to secure the screws in the four plastic expansion bolts firmly.
Step 5
Adjust the device position and line up the three inner hexagon screws of the device to the three holes of
the installation position. Put the three inner hexagon screws into the screw holes at the bottom of the
pedestal. Use the inner hexagon screwdriver to fix firmly. Connect the GND to the ground wires to
improve stability. See Figure 3-3 .
With IR light Without IR light
Figure 3-3
Step 6
Adjust the X-Y-Z axis module to turn the device to the proper monitor angle. Please follow the steps
listed below to adjust. See Figure 3-4.
Please note, for the dome of the IR light, you can skip step a) and step e).
z a): Slightly push the two sides to squeeze the plastic hook so that you can take off the dome
enclosure.
z b):Slightly loose the screws at the two sides of the X-Y-Z module manually, you can adjust the
module tilt rotation angle (15°～90°).
z c):Slightly loose the screw of the pressing slice, you can adjust the video rotation angle of the
module (0°～355°)
z d):Adjust the turning ring of the pedestal, you can adjust the module pan rotation angle (
0°～355
°).
17
z e): Put the enclose back after you completed the setup.
With IR light Without IR light
Figure 3-4
Please note, the screws in the following figure are the optical adjustment component. Please
make sure it is outward and do not allow it to touch the X-Y-Z axis module. See Figure 3-5
Figure 3-5
Step 7
Put the dome cover back and then put the three inner hexagon screws into the holes of the device. Use
the inner hexagonal wrench to fasten these three screws. See Figure 3-6
Figure 3-6
18
3.2 SD Card Installation
Important
Before you install the SD card, please unplug he power cable to shut down the device!
First, please refer to the step1 in the chapter 3.1 to open the device.
Second, please adjust the proper position to install the SD card.
Last, please refer to the step 7 in the chapter 3.1 to complete the installation. See Figure 3-7.
With IR light Without IR light
Figure 3-7
3.3 Lens Adjustment
Step 1
Slightly loose the screw B manually and then turn the screw B slowly. Adjust the lens focus distance to
the proper position according to the monitor video. See Figure 3-8.
Step 2
Use the flat screwdriver to loose the screw A slightly and then turn the Screw A slowly. Adjust the lens
focus to get the clear video and then use the flat screwdriver to secure the screw firmly.
Step 3
When you are adjusting the screw A, the video may becomes blur. Please slightly adjust the screw B
manually to get the vivid video. Finally fix the screw.
19
With IR light Without IR light
Figure 3-8
20
4 Quick Configuration Tool
4.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
4.2 Operation
Double click the “ConfigTools.exe”icon, you can see an interface is shown as in Figure 4-1.
In the device list interface, you can view device IP address, port number, subnet mask, default gateway,
MAC address and etc.
Figure 4-1
Select one IP address and then right click mouse, you can see an interface is shown as in Figure 4-2.
Figure 4-2
21
Select the “Open Device Web” item; you can go to the corresponding web login interface. See Figure
4-3.
Figure 4-3
If you want to modify the device IP address without logging in the device web interface, you can go to
the configuration tool main interface to set.
In the configuration tool search interface (Figure 4-1), please select a device IP address and then double
click it to open the login interface. Or you can select an IP address and then click the Login button to go
to the login interface. See Figure 4-4.
In Figure 4-4, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in Web
Network interface. Otherwise, you can not login the device.
If you are use device background upgrade port 3800 to login, other setups are all invalid.
Figure 4-4
After you logged in, the configuration tool main interface is shown as below. See Figure 4-5.
22
Figure 4-5
23
5 Web Operation
This series IPC product support the Web access and management via PC.
Web includes several modules includes monitor channel preview, PTZ control, system configuration,
alarm and etc.
IP camera factory default setup:
z IP address: 192.168.1.108 or DHCP.
z User name: admin
z Password: admin
5.1 Network Connection
Please follow the steps listed below for network connection.
z Make sure the IPC has connected to the network properly.
z Please set the IP address, subnet mask and gateway of the PC and the IPC respectively. IPC
default IP address is 192.168.1.108. Subnet mask is 255.255.255.0. Gateway is 192.168.1.1
z Use order ping ***.***.***.***(IP camera address) to check connection is OK or not.
5.2 Login and Main Interface
Open IE and input IP camera address in the address bar.
For example, if your camera IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address
bar. See Figure 5-1.
Figure 5-1
The login interface is shown as below. See Figure 5-2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
Input your IP
address here
24
Figure 5-2
If it is your first time to login in, system pops up warning information to ask you whether install control
webrec.cab
or not after you logged in for one minute. Please click OK button, system can automatically
install the control. When system is upgrading, it can overwrite the previous Web too.
If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable the
control download. Or you can lower the IE security level. See Figure 5-3.
Figure 5-3
After you logged in, you can see the main window. See Figure 5-4.
25
Figure 5-4
Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction.
26
6 FAQ
Bug
I can not boot up
the device.
Please click RESET button for at least five seconds to restore
factory default setup.
SD card write
times
Do not set the SD card as the storage media to storage the
schedule record file. It may damage the SD card duration.
I can not use the
disk as the storage
media.
When disk information is shown as hibernation or capacity is 0,
please format it first (Via Web).
I can not upgrade
the device via
network.
When network upgrade operation failed, you can use port 3800 to
continue upgrade.
Recommended SD
card brand
Kingston 4GB， Kingston 1GB， Kingston 16GB， Transcend
16GB， SanDisk 1G， SanDisk 4G, 32GB Class4
Usually we recommend the 4GB (or higher) or industry-level high
speed card in case the slow speed results in data loss.
Audio function Please use active device for the audio monitor input, otherwise there
is no audio in the client-end.
The lightproof ring
of the IR device
The lightproof ring of the IR device lens is the necessary component
when it works. You can not view the clear video when the IR light is
on if you remove the lightproof ring.
27
Appendix Toxic or Hazardous Materials or Elements
Toxic or Hazardous Materials or Elements
Component
Name
Pb Hg Cd Cr VI PBB PBDE
Circuit Board
Component
○ ○ ○ ○ ○ ○
Device
Construction
Material
○
○ ○ ○ ○ ○
Wire and Cable
○
○ ○ ○ ○ ○
Packing
Components
○ ○ ○ ○ ○ ○
Accessories ○ ○ ○ ○ ○ ○
O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the
parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the
environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements
contained in products will not leak or mutate so that the use of these (substances or elements) will not
result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer
is not authorized to process such kind of substances or elements, please return to the corresponding
local authorities to process according to your local government statutes。
Note
z This user’s manual is for reference only. Slight difference may be found in user interface.
z All the designs and software here are subject to change without prior written notice.
z If there is any uncertainty or controversy, please refer to the final explanation of us.
z Please visit our website for more information.
Loading...