HDCVI Camera
User’s Manual
ank you for purchasing our HDCVI camera!
is user’s manual is designed to be a reference tool for
your system.
Please read the following safeguard and warnings
carefully before you use this series product!
Please keep this user’s manual well for future ref
Welcome
erence!
Important Safeguards and warnings
1.Electrical Safety
all installation and operation here should conform to your local electrical safety codes.
e power shall conform to the requirement in the SELV(Safety Extra
Low Voltage) and the Limited power source is rated 12V DC (24V AC)
in the IEC60950-1.
We assume no liability or responsibility for all the res or electrical
shock caused by improper handling or installation.
2.Transportation Security
Heavy stress, violent vibration or water splash are not allowed during
transportation, storage, and installation.
3.Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-o device during the installation
connection.
Always follow the instruction guide the manufacturer recommended.
If this product is installed in the ceiling, please make sure this installation position can sustain the min 50N.
4.Qualied Engineers needed
All the examination and repair work should be done by the qualied
service engineers.
We are not liable for any problems caused by unauthorized modications or attempted repair.
5.Environment
is series camera should be installed in a cool, dry place away from direct sunlight or strong light, inammable, explosive substance and etc.
Important Safeguards and Warnings
is series camera be used in the specied working temperature. Please keep it away from electromagnetic radiation objects and environments.
Please keep the sound ventilation.
Do not allow water and other liquid from falling into the
camera.
6.Accessories
Be sure to use all the accessories recommended by the manufacturer.
Before installation, please open the package and check all
the components that are included.
Contact your local retailer ASAP if something is broken in
your package.
7.Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance work.
Use the dry so cloth to clean the device.
If there is too much dust, please use water to dilute the mild
detergent rst and then use it to clean the device. Finally
use the dry cloth to clean the device.
Please put the dust-proof cap on to protect the CCD
(CMOS) component when you do not use the camera.
1
1.1 Overview
is series megapixel HD camera conforms to the HDCVI standard. It supports video signal high-speed long distance transmission without any delay.
It can be controlled by the DVR conforming to the HDCVI.
1.2 Features
• High-performance CMOS image sensor, megapixel denition.
• Support HD video and control signal coaxial transmission.
• Supports 75-3 coaxial cable transmission without any loss. 720P series
transmission distance over 500m, 1080p series transmission distance
300m.
• High speed, long distance real-time transmission
General Introduction
• Support HDCVI HD and along SD switch output.
• 720p series supports 720p@25, 720p@30, 720p@50, 720p@60.
• 1080p series support 1080p@25, 1080p@30
• Supports high performance 3D noise reduction, excellent
performance in low illumination.
• Support ICR switch to realize surveillance both in the daytime and at
night.
• 3.6mm xed lens (2.8mm, 6mm, 8mm optional)
• Support OSD(on-screen display), suitable for user self-dened setup.
• Supports DC12V power supply.
• IP66 compliance.
• Supports intelligent IR function.
2
Dome Framework and Dimensions
Please refer to the following gures for Dimension information. e unit is mm(millimeter).
Important
Dimensions of Cameras may vary depending on your
model. If you are having trouble nding the dimensions
you can nd the measurements by using a caliper or try
your best using a ruler. To nd the circumference of the
bottom of the camera use the following formula: Diameter of circle x 3.14(pi)
Lens
Dome Body
Decoration Ring
HD-CVI Metal Housing
1
Power
Video
SD/HD switch control cable
2
HD-CVI Plastic Housing
Lens
Dome Body
Decoration Ring
Dome Cover
3
HD-CVI Glass Housing
Dome Enclosure
Video Output Port
IR Light
Dome Module
Dome Pedestal
Power Input Port
SD/HD Switch Cable
When the Standard denition/high denition switch control cable is short
circuit, systems outputs standard denition video. Otherwise, when the circuit is open, system outputs the high denition video.
3
Important
Before the installation, please make sure the installation surface can sustain
at least 3X weight of the bracket and the camera.
3.1
e dome camera usually uses the ceiling installation. It can be installed on
the ceiling or the wall.
• For the side exit cable installation, please make sure the side exit cable
direction is the same as shown in the installation position map.
• Before you secure the screws on the pedestal, please put the cable
through the cable exit of the pedestal.
HD-CVI glass housing
Dome Installation
• Before you complete the installation and debug, do not remove the
electrostatic lm. Aer you remove the lm, do not touch the enclo
sure in case there are any scratches.
Ceiling or Wall
Installation Position Map
Expansion Bolts
Self-Tapping Screw
Enclosure fastening screw
Inner Hex Wrench
Step 1
Take the installation position map from the accessories bag and them put it on
the surface of the ceiling or the wall according to the cable exit position. Dig
three holes according to the installation position map and then take three expansion bolts from the accessories bag and put them to the holes you just dug.
Step 2
Use inner hex wrench to remove the three enclosure fastening screws and then
remove the dome enclosure.
Step 3
Adjust the pedestal position according to the cable exit move(ceiling/side).
Pull the cable through the cable side exit at the installation surface and the
pedestal (Please skip this step if you want to use ceiling exit mode). Line up
the screw holes at the bottom of the pedestal to the expansion bolts in the installation surface. Put three self-tapping screws to expansion bolts and then
secure rmly. Now the pedestal is on installation surface.
Step 4
Adjust the camera module angle to a proper position and then x the screws
to fasten.
Fastening Screw
Step 5
Use three enclosure fastening screws to secure the dome housing on
the pedestal.
3.2
Step 1
Please take the installation position map in the accessories bag, and then
paste it on the ceiling or the wall according to your monitor area requirements. Draw and then dig three holes in the installation surface and then
insert three expansion bolts in the holes. Secure these three bolts rmly.
Step 2
Turn counter clockwise to remove the decoration ring. Please dig a “cable
exit hole” in the surface according to the installation position map if you
want to draw out the cable from the top of the installation surface. You need
to draw out the cable from the cable channel side port of the pedestal if you
want to draw out the cable from the side port of the cable channel. Adjust
the device installation pedestal to the proper position and then draw the
cable through the cable exit. Line up the three screw holes in the installation
HDCVI Plastic Housing
position. Put the three self-tapping screws in the three plastic expansion
bolts rmly. Now the dome camera is secure in the installation surface.
Ceiling or Wall
Expansion Bolt
Dome Camera Body
ST3 Self-tapping Screws
Decoration Ring
Step 3
Adjust the lens to get the clear monitor video. Use cross-head screwdriver to
loosen the screw and then turn the camera body to the proper position manually. Fix the screw again.
Important
Do not remove the screw. Loosen a little bit. Please secure aer you have
completed the setup.
Adjustment Screw
Cross-head Screwdriver
Step 4
Line up the bulge of the decoration ring to the nick of the camera body and
install along the tilt installation. Push and then turn decoration ring clockwise. e installation completed aer you secure the decoration ring. You
need to use the proper tool to open up the side port of the U-cable channel
of the decoration ring if you want to draw out the cable from the side port of
the cable channel when you are installing the device cable. And then you can
draw out the cable from the cable channel of the pedestal. Finally you can
install the decoration ring to complete the installation.
3.3
Step 1 Device Installation
Take the wrench from the accessories bag and use it to loosen the three set
of screws on the side of the camera body.
HDCVI Metal Housing
Step 2 Pedestal installation
Turn the pedestal of the device and then pull the cable through it. Use four
screws to secure the pedestal to the proper position.
Pedestal 1
Step 3 Adjust Monitor Angle
Turn the pan base to the pedestal and secure rmly. Adjust rotate base and
the dome body to get the lens to the proper monitor angle.
B1 Pedestal
B2 Pan Base
B3 Rotate Base
B4 Dome Body
Step 4 Fix Monitor Angle
To prevent the dome from moving, use wrench to secure the three set
screws to secure the monitor angle position.
4
Bullet Framework Dimensions
Please refer to the following gures for Dimension information. e unit is mm(millimeter).
Important
Dimensions of Cameras may vary depending on your
model. If you are having trouble nding the dimensions
you can nd the measurements by using a caliper or try
your best using a ruler. To nd the circumference of the
bottom of the camera use the following formula: Diameter of circle x 3.14(pi)
Lens
Sun-Visor
Bracket
5
Important
Before the installation, please make sure the installation surface can sustain
at least 3X weight of the bracket and the camera.
Bullet Installation
2 Megapixel Camera
Before you install the bracket, please pull the cable through the cable exit of
the bracket chassis.
• Please install the expansion bolt if you want to install in cement wall
(please make sure the installation holes of the expansion bolts are
the same as the bracket) then you can install the bracket.
• If you want to install in woof surface, please skip the rst step and then
use the self-tapping screws to install the bracket directly
Step 2
Unscrew the M3 x 20 and M3 x 5 screws on the bracket and adjust the
camera via the three directions indicated in the gure below have the camera facing the exact location which needs to be monitored by rotating the
bracket and camera body, then secure the bolts.
2
1
3
Vari-Focal Camera
Unscrew M2 5*5 Bolt from the
lower cover of the camera. Remove
the Cover and adjust the vari-focal(zoom) to your preference.
Lens Focal Lens
Lower Cover
M2 5*5 Bolt
5
Menu
5.1
e following operation and interfaces for reference only. Please refer to
the HDCVI series DVR user’s manual for detailed information.
Aer connecting the camera to the HDCVI series DVR, from Main Menu
->Setting->System->PTZ, you need to set control mode as HDCVI and the
protocol as DH-SD1. Click save button to save current setup.
HDCVI Series DVR settings
On the preview interface, right click mouse and then select PTZ; you can
see an interface shown as below.
Click Iris “+” to open menu or conrm current operation. Click up/down
button to view all the items on the le pane of the following list. Click le/
right button to set the corresponding values on the right pane of the following list. If there is , click conrm button to go to the 2nd menu. Repeat
the previous steps to set detailed value. Click return button to go back to
the previous menu interface.
Loading...