Securitron ASB-32BK, ASB-32CL, ASB-62BK, ASB-62CL, ASB-82BK Installation Instructions

10027 S. 51st St. Ste 102
Phoenix, AZ 85044
Tel: [phone]
Mon-Fri: 6:00am - 4:00pm PDT

securitron.com
[e-mail]

Aluminum Spacer Bracket

(Models ASB-32, ASB-62, and ASB-82)

Installation Instructions

INTRODUCTION

The Aluminum Spacer Bracket (ASB) is a 1/2” [12.7 mm] thick, anodized,
aluminum spacer bracket with individual designs for the Models M32, M62, or
M82 Magnalocks
glass doors with or without blade stops may require an ASB, which improves
frame mounting strength, Magnalock/Strike clearances, alignments, and also
eases installation (see Figure 2, “Installation Cross Section”).

®

(see Figure 1, “ASB Group”). Installations in aluminum frame

Figure 1. ASB Group

Figure 2. Installation Cross Section

1

securitron.com

RECOMMENDED INSTALLATION TOOLS

• Power Drill

• 3/8” [9.53 mm], 27/64” [10.72 mm] Drill Bits

• 1/2” Wrench or Adjustable

• Center Punch

• 3/16” Hex Wrench

INSTALLATION

Mounting the Strike

1. Prior to proceeding, DETERMINE the proper location for mounting the strike
in relation to the Magnalock, and CONSIDER the following:

• Aluminum-frame, glass doors vary depending on the top rail (shoe) size

and the internal structural design.

• In a narrow frame, once the Magnalock is spaced down by the ASB, it

may not be possible to install the sex bolt for the strike without hitting
glass or an internal structure (e.g., cable); therefore, supplied hardware
with the ASB allows the strike to be directly mounted to the door using a
special 5/16-18 [8 mm-1.5 mm] threaded blind nut.

2. IF mounting the strike on a conventional frame rail,

AND the use of an ASB is required,
THEN MOUNT the strike using a sex bolt and as described in the applicable

Magnalock instructions.

3. IF mounting the strike on a aluminum-frame, glass door,

AND the use of an ASB is required,
THEN PERFORM the following.

a. DRILL a 1/4” starter hole into the door in the location where the sex bolt

would normally be used.

b. INSPECT for any structural door component that might interfere with the

use of a sex bolt (e.g., cable or bar).

c. IF there are no structural door components in the way,

THEN MOUNT the strike using the sex bolt and as described in the
applicable Magnalock instructions.

NOTE: When properly collapsed, a special blind nut provides adequate

security for the strike in an aluminum-framed, glass door.

d. IF there are structural door components in the way,

AND the use of a sex bolt is not
THEN MOUNT the strike on the door using a special blind nut and

mounting screw.

feasible,

2

securitron.com

Mounting the Strike using a Special Blind Nut and Mounting Screw

NOTE: Figure 3, “Blind Nut Components,” and Figure 4, “Special Blind Nut

Installation,” provide illustration for the following steps.

Figure 3. Blind Nut Components

Figure 4. Special Blind Nut Installation

1. DRILL the marked mounting hole location in the door using a
27/64” [10.72 mm] drill bit.

2. THREAD the additional hardware into the 5/16-18 cap screw, as shown in
Figure 3.

3. INSERT the 5/16-18 [8 mm-1.5 mm] blind nut fully into the mounting hole.

4. INSERT the 5/16-18 cap screw with additional hardware into the special
blind nut.

NOTE: Use of a lubricant on the blind nut threads is required to keep the

assembly from spinning and not collapsing.

5. Using a box wrench to hold the hex nut in position, TURN the cap screw with
an Allen Wrench 3 to 4 complete turns to collapse the blind nut.

6. REMOVE the cap screw

7. POSITION and MOUNT the strike onto the door.

8. TIGHTEN the cap screw to secure the strike to the door.

3

securitron.com

Mounting the ASB and Magnalock

500

500, Re

NOTE: Figure 5, “ASB and Magnalock Installation,” provides illustration for

the following steps.

1. MARK the cable access hole and the mounting holes where the 1/4-20 blind
nuts will be located using the provided Magnalock template, and CENTER
PUNCH.

2. DRILL a 1/8” or 1/4” starter hole.

3. DRILL the marked mounting hole locations in the frame using a
3/8” [9.53 mm] drill bit.

4. DRILL the marked hole for the cable access into the frame as indicated on
the provided Magnalock template.

NOTE: Socket head cap mounting screws are provided in the ASB hardware

package and the washers are provided in the applicable Magnalock
hardware package.

5. THREAD the additional hardware onto each 1/4-20 cap screw, as shown in
Figure 3.

6. INSERT each 1/4-20 blind nut fully into a mounting hole.

NOTE: Use of a lubricant on the blind nut threads is required to keep the

assembly from spinning and not collapsing.

7. One by one, and using a box wrench to hold each hex nut in position, TURN
each cap screw with an Allen Wrench 3 to 4 complete turns to collapse its
blind nut.

8. REMOVE the cap screws.

9. POSITION the Magnalock and cable onto the ASB bracket.

10. MOUNT the Magnalock and ASB assembly onto the frame.

11. INSERT and securely TIGHTEN the cap screws.

Figure 5. ASB and Magnalock (M62 shown) Installation

© 2015, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company.

4

-17

v E