Secure Tech ST2 Installation Manual

ST2 Installation Manual

Keyless Access System Solutions

Secure Tech

2

Wall Screws

Male Clicking
Supports

Indication Leds
Red: Power
Yellow: Programming
mode
Green: successful
operation

Controller
Keypad

Female
Clicking
supports

Back screws

USB Interface
Connector
Laptop/Notebook

Secure Tech www.setech.ca

ST2 Keyless Access System - Parts Description

Door Controller - Front View Door Controller - Back View

Door Controller - Wall Supporting Plate Proximity Reader

Proximity Keyfob Locking Device Protection Diode

USB Interface Cable Power Supply

Phone: [phone] www.setech.ca Fax: [phone]

3

Access Control One (1) Door

Access Control Two (2) Doors

AC Power outlet
110VAC/220VAC
Magnetic lock

Door contact (Optional)

Choose Electric
Strike or
Magnetic lock

Electric Strike

Magnetic lock
Door contact (Optional)

Choose Electric
Strike or
Magnetic lock

Electric Strike

Proximity Card
Reader

Door controller module
(installed indoors)

12 DC Power
Supply

Proximity Card
Reader

Door controller module
(installed indoors)

12 DC Power
Supply

Magnetic lock
Door contact (Optional)

Choose Electric
Strike or
Magnetic lock

Electric Strike

Release push button
Door2 (optional)

Release push button
Door1 (optional)

Release push
button (optional)

Laptop to perform
management operations

Laptop to perform
management operations

Proximity Card
Reader

Choose locking device: electric strike or magnetic lock

Choose locking device: electric strike or magnetic lock
Choose locking device: electric strike or magnetic lock

Secure Tech www.setech.ca

Installation diagrams

Phone: [phone] www.setech.ca Fax: [phone]

4

Access Control one (1) Door + Exit Registration

AC Power outlet
110VAC/220VAC

Proximity Card
Reader

12 DC Power
Supply

Magnetic lock
Door contact (Optional)

Choose Electric
Strike or
Magnetic lock

Electric Strike

Release push
button (optional)

Laptop to perform
management operations

Proximity Card
Reader - Exit
Registration

Choose locking device: electric
strike or magnetic lock

Secure Tech www.setech.ca

Phone: [phone] www.setech.ca Fax: [phone]

5

Secure Tech www.setech.ca

Controller Module: Board connectors description and recommended cables

Recommended Cables:

Proximity Reader:

 6 Conductors x 22 AWG - Shielded

(5 cables used). Maximum distance: 300 feet (100 meters)

Electric Strike or Magnetic Lock:

 Option 1: 2 Conductors x 18 AWG
 Option 2: Quad cable: 4 conductors x 22 AWG

Power supply:

 Option 1: 2 Conductors x 18 AWG
 Option 2: Quad cable: 4 Conductors x 22 AWG

Door Contact:

 2 Conductors x 22 AWG

Door Release (REX):

 2 Conductors x 22 AWG

Phone: [phone] www.setech.ca Fax: [phone]

6

Door contact (normally
open)

Vcc

Power Supply: 12Vdc

Prox. Reader 1

Vcc

Gnd

Gnd

Proximity Reader
Cables

Red - +Vcc
Black - Gnd
Green – Data0
White – Data1
Blue - Led
Grey – No connection
Yellow – No connection
Brown – No connection

Prox. Reader 2

D0

D1

Led

Vcc

Gnd

D0

D1

Led

V V V V V V
2 2 2 1 1 1
C N N C N N
0 C 0 C

Door 2

Door 1

DO D1 led

Vcc

Gnd

DO

D1

Led

Door
Contact

Release

Door 1

Door 2

Ext. Bz

Protection Diodes

Electric Strike Door 2

Electric Strike Door 1

D0

+12V

Gnd

B

E

B

C

A

Release
Door 1

Release
Door 2

+

External
Buzzer

Secure Tech www.setech.ca

Typical connection with 12VDC Electric Strikes

Phone: [phone] www.setech.ca Fax: [phone]

7

Secure Tech www.setech.ca

Phone: [phone] www.setech.ca Fax: [phone]

8

Secure Tech www.setech.ca

Installation Instructions:

1) Make the necessary holes in the wall for: Door controller, proximity reader, prepare the door frame to

install the locking device

2) Run cables for proximity reader, electric lock, DC power supply and door contact(optional

3) Install the proximity reader, Electric Lock or Magnet Lock

4) Unscrew the four screws on the back of the door controller

5) Connect and screw the cables(electric lock, proximity reader, DC power, door contact, door release) to

the controller connectors

6) Push the controller aligning the clicking supports females(door controller) and the clicking supports

males (wall supporting plate)

7) Plug the power supply to the AC power outlet(110AC or 220 AC)

Software Download:

Download ST2 Management software.
Specific software versions for:

 Companies and institutions
 Commercial buildings
 Residential buildings
 Households

Phone: [phone] www.setech.ca Fax: [phone]