SecureALL SA-MDR Installation Manual

Page 1
SecureALL Corporation
SA-MDR Installation Guide
Version 3.0
Page 2
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 2 of 22
All Rights Reserved
SecureALL Corporation SA-MDR Installation Guide
Copyright © 2012 by SecureALL Corporation.
All rights reserved under International and Pan-American copyright conventions. No part of this document may be reproduced in any form or any means, electronic or mechanical, including photocopying, without permission in writing from the Company. All inquiries should be
addressed to SecureALL Corporation, 695 Woburn Court, Mountain View, CA 94040.
Page 3
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 3 of 22
All Rights Reserved
Revision History
Version
Date
Author
Revision Description
1.0
02-15-2012
JDS
Initial version
2.0
08-15-2012
RAS
Added step for changing lock from RH to LH; added instructions for installing the flex cable that has replaced the 14-pin cable; added step to check current level post battery installation; new mortise cutout template.
3.0
7-16-2013
RAS/DAC
Added spacer and corrected bill of materials
Page 4
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 4 of 22
All Rights Reserved
Table of Contents
Revision(History(.............................................................................................................................(3(
Table(of(Contents(...........................................................................................................................(4(
Introduction(.....................................................................................................................................(5(
Configuring(the(Mortise(Chassis(..............................................................................................(6(
Installation(Instructions(.............................................................................................................(7(
Appendix(A(-(Mortise(Cutout(Template(...................................................................(16(
Appendix(B(-(Mortise(Lock(Assembly,(Exploded(View(.........................................(18(
Appendix(C(-(Screw(Package(.......................................................................................(19
(
Page 5
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 5 of 22
All Rights Reserved
I. Introduction
These instructions are to be used to install a SecureALL SA-MDR mortise door reader. This document assumes availability of a door with a cutout pocket for an industry standard, ANSI Grade 1, heavy-duty mortise lock. See Appendix A for cutout dimensions.
Required Tools:
1. Phillips head screwdriver (Size #3 Drive)
2. Phillips head screwdriver (Size #2 Drive; pitch: 0.6) for Escutcheon Cover Screws
3. Allen wrench - supplied by SecureALL
Check the Materials:
Verify that the following materials are included and there is no visible damage. If there are any damaged or missing items, contact SecureALL immediately for assistance. See Appendix B for an exploded view of the lock and Appendix C for pictures of the screw hardware.
ITEM NO. PART NO. DESCRIPTION QTY
1 190-000176 FACE PLATE 1
2 850-000122 MORTISE CHASSIS ASSEMBLY 1
3 190-000177 INSIDE LEVER ASSEMBLY 1
4 190-000178 OUTSIDE LEVER ASSEMBLY 1
5 190-000171 SPINDLE W/SCREW (SET) 1
6 190-000189 SPACERS, 1/4" HIGH 2
7 190-000172 MOUNTING POST 2
8 190-000173 TRIM SCREW 2
9 820-000127 INSIDE COVER ASSEMBLY 1
10 820-000128 OUTSIDE COVER ASSEMBLY 1
11 820-000129 INSIDE RF ASSEMBLY 1
12 190-000175 DUST BOX 1
13 190-000179 STRIKE PLATE 1
14 190-000168 MORTISE SCREW 2
15 190-000166 CHASSIS SCREW 2
16 190-000170 SCALP SCREW 2
17 190-000167 ESCUTCHEON COVER SCREW 3
18 190-000169 STRIKE SCREW - FINISHED 2
19 530-000100 AA BATTERIES 3
Page 6
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 6 of 22
All Rights Reserved
II. Setting the mortise chassis
The diagram below gives the instructions to change from an inside (i.e. door opens in) to an outside (i.e. door opens out) lock unit or from an outside to an inside lock unit. Picture #1 shows an outside opening right hand door and #4 shows an inside opening right hand door.
Page 7
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 7 of 22
All Rights Reserved
If it is necessary to change from a left hand inside opening lock unit to a right hand inside opening lock unit (or vice versa), first follow the procedure above to reverse the latch bolt. The locking side must then be reversed. Unscrew the two screws in the left figure below and put them in the same screw holes on the other side of the chassis.
III. Installation Instructions for Left Hand, Inside Opening Door
1. Orienting the Chassis Assembly (Item 2) as shown in Figure 1a, carefully thread the two
cables into the door pocket and through the second hole as shown in Figure 1b. Holding the cables taut, push the Chassis Assembly all the way into the pocket.
Figure 1a Figure 1b
Page 8
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 8 of 22
All Rights Reserved
2. Using Mortise Screws (Item 14), secure the Chassis Assembly to the door, as shown in
Figure 2.
Figure 2
3. Place the outside Spindle (Item 5A) and inside Spindle with Screw (Item 5B) in the
Chassis Assembly and tighten the screw that is embedded inside Item 5B with the Phillips screwdriver. See Figures 3a & 3b.
Figure 3a Figure 3b
Item 14
Item 5B
Item 5A
Page 9
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 9 of 22
All Rights Reserved
4. Mount Outside Lever Assembly (Item 4) on the outside Spindle. Insert Mounting Posts
(Item 7) through the holes in the Outside Lever Assembly, making sure they are completely inserted. See Figure 4.
Figure 4
5. Mount the Outside Cover Assembly a. Hold the Outside Cover Assembly (Item 10) perpendicular to the door as shown
in Figure 5a.
Figure 5a
Item 7
Page 10
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 10 of 22
All Rights Reserved
b. Slide the Outside Cover Assembly toward the handle until it butts up against the
handle end (Figure 5b).
Figure 5b
c. Rotate the Outside Cover Assembly clockwise and then push it toward the handle
until the end is within the Outside Cover Assembly cutout (Figure 5c).
Figure 5c
Page 11
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 11 of 22
All Rights Reserved
d. Feed the handle through the cutout, rotate the Outside Cover Assembly
counterclockwise and continue pushing onto the handle (Figure 5d).
Figure 5d
e. When halfway onto the handle, insert the flex cable through the upper hole
(Figure 5e).
!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Figure 5e
Page 12
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 12 of 22
All Rights Reserved
f. Complete pushing the Outside Cover Assembly onto the handle (Figure 5f).
Figure 5f
6. Holding the Outside Cover Assembly flush to the door, align the Inside RF Assembly
(Item 11) screw holes with the top and bottom holes in the door. Use Chassis Screws (Item 15) to secure the Inside RF Assembly to the door. See Figure 6. Do not fully tighten the screws at this point.
Figure 6
Item 15
Page 13
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 13 of 22
All Rights Reserved
7. Mount the Inside Lever Assembly (Item 3) on the Spindle with Screw. Place a spacer
(Item 6) on each Trim Screw (Figure 7a). Insert the Trim Screws (Item 8) into the Inside Lever Assembly holes (Figure 7b). Fasten the screws until they are tight. Tighten the Inside RF Assembly screws in Step 6. Be cautious not to overtighten any of the screws. Work the handles and make sure there is no binding. If binding occurs, back off each of the screws slightly until there is no binding. If binding continues, it will be necessary to remove the chassis and widen the cutout slightly.
Figure 7a Figure 7b
8. Mount the Inside Cover Assembly on the Inside Lever by following the same steps as in
Step 5. Holding the Inside Cover Assembly (Item 9), in the order shown below, connect to the printed circuit board (PCB) the three cables that are sticking through the Inside RF Assembly and the battery box cable.
a. Flex cable (Figure 8a) -
Figure 8a
Item 8
Flex cable
Item 9
Flex cable socket
Page 14
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 14 of 22
All Rights Reserved
Important note: The flex cable and socket are very delicate and must be handled as discussed here to avoid damage.
The flex cable socket is the brown unit at the bottom of the PCB shown above. Start by pressing in fully the upper moveable part of the socket. Grab both ends of the moveable part and gently pull until fully extended. Take the flex cable and, with the blue side facing up, insert it into the socket. Push it in as far as it will go without force. Holding it in this position, press both sides of the moveable part of the socket simultaneously until it locks into place. Gently pull on the flex cable to ensure it is secure. The flex cable should be square to the socket, i.e. the same amount of blue should be visible at the socket from one side to the other, It should not be cocked or crooked relative to the socket.
b. Motor cable (Figure 8b) -
Figure 8b
The motor cable is two-wire, black/red and is inserted into its socket with the smooth side up. (Note: Other than the flex cable, the cables are keyed and can only be inserted with the correct orientation into the appropriate socket on the PCB.)
c. Latch position cable (Figure 8c) -
Motor cable
Page 15
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 15 of 22
All Rights Reserved
Figure 8c
The Latch Position Cable is five wire, Yellow/Green/White/Black and goes into the socket at the top left of the PCB. The connector top is stepped, not smooth.
d. Power (battery box) cable (Figure 8d) -
Figure 8d
Latch position cable
Power cable
Page 16
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 16 of 22
All Rights Reserved
The Power Cable is two-wire, black/red, but is attached to a four-wire connector that goes into the socket at the top right of the PCB. The top side of the connector is stepped, not smooth.
e. After all cables are attached, the assembly will look as shown in Figure 8e. Take
any excess wire for the Motor and Latch Position Cables and push it back through the hole in the Inside RF Assembly to make it easier to install the Inside Cover Assembly.
Figure 8e
9. Insert the three AA batteries (Item 19) into the battery box in the Inside RF Assembly.
Make sure the polarity of the batteries is correct.
Figure 9
Page 17
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 17 of 22
All Rights Reserved
As soon as the last battery is installed, a red LED will light up and remain solid for a couple of seconds. It will then flash on and off five times before turning off. If this sequence is not observed (i.e., the LED may remain solid red or flash on and off indefinitely), then there is a problem with the lock. Detach all the cables and repeat Steps 8a-8d. If the required sequence is still not observed, set the unit aside for further investigation.
10. Make sure the battery cable is routed to the outside of the battery box via the cable guide
and the flex cable is not "pinched" in any way as the Inside Cover Assembly is routed all the way onto the Inside Lever. Secure the Inside Cover Assembly with three Escutcheon Cover Screws (Item 17).
Figure 10a Figure 10b
Item 17
Page 18
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 18 of 22
All Rights Reserved
11. Fasten Face Plate (Item 1) using the Scalp Screws (Item 16).
Figure 11
12. Insert the Dust Box (Item 12) and the Strike Plate (Item 13) in the door frame cutout and
secure with the Strike Screws (Item 18).
Item 16
Page 19
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 19 of 22
All Rights Reserved
APPENDIX A - MORTISE CUTOUT TEMPLATE
Page 20
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 20 of 22
All Rights Reserved
APPENDIX A - MORTISE CUTOUT TEMPLATE
Page 21
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 21 of 22
All Rights Reserved
APPENDIX B - MORTISE LOCK ASSEMBLY, EXPLODED VIEW
Page 22
Nnn-0000nn © Copyright 2012 SecureALL Corporation Page 22 of 22
All Rights Reserved
APPENDIX C - SCREW PACKAGE
190-000170
SCALP SCREW
190-000169
STRIKE SCREW - FINISHED
190-000168
MORTISE SCREW
190-000173
TRIM SCREW
190-000172
MOUNTING POST
190-000171
SPINDLE SET
190-000167
ESCUTCHEON COVER SCREW
190-000166
CHASSIS SCREW
Loading...