Beanbag Thermostat
This is a Z-Wave Plus enabled battery-powered
portable controller designed for home heating
system, it act as a room thermostat if used with
Beanbag Receiver.
It is having OLED display to show the ambient
and target (Set-point) temperature, these
parameter and also reported over Z-Wave to
associated nodes.
It can be operated in any Z-Wave network with
other Z-Wave certified devices from other
manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of
vendor to increase reliability of the network.
Operational Modes
Device support Normal and Advance mode, by default device is in normal mode, mode can be switched
by long press of OK button.
Advance mode is designed to perform device setup and network installation and configurations, refer
table Advance Mode for more information.
Inclusion / Exclusion
Inclusion:- Power up device (by pulling out battery strip), start Add node on Z-Wave controller and click
Ok button when device display instructing to click OK button, this will start learn process in device.
Exclusion:- Start Remove node on Z-Wave controller, on thermostat enter in Advance mode, and then
scroll to option “Activate Learn mode”, then click OK button.
Thermostat will display learn outcome on completion of the process.
Add / Remove
On thermostat in advance mode scroll to option “Add device / Remove device”, then click OK button. On
other Z-Wave device start learn process, thermostat will display outcome on completion of the process.
Wakeup from Sleep
On thermostat, click OK button when device screen is off, or in advance mode scroll to option “Enter
listening mode” then click OK button.
1
Advance Mode
Function Description
Add device(1)
Include any Z-Wave device into its network
Remove device(1)
Exclude any Z-Wave device from network
Activate Learn mode(1)
Start Learn process for inclusion / Exclusion from other network
Enter listening mode(1)
Listen mode for sending Wakeup Notification to wake up node if configured
Broadcast device
Information
Broadcast its Node Information Frame (NIF)
Check
signal
strength (2)
RF signal strength test using power level CC with associated node in Group 2
Outcome
Network Health
Action on associated node
3 bars
Good
No action
2 bars
Acceptable
May move node, or install repeater node in-between
1 bar
Insufficient
Must move node, or install repeater node in-between
Factory reset
Perform protocol reset, set thermostat configurations to factory default.
Note: Please use this procedure only when the network primary
controller is missing or otherwise inoperable.
Associate Channel(1)
Associate node in group 2 by Classic / Multichannel association, using NIF /
Multichannel capability report from other Z-Wave device (node).
Remove channel
association(2)
Remove associated node from association group 2
View associated
channel ID(2)
Display associated end point (Channel number ) in association group 2
Display Text
Description
None
No End point available in association group
CH x
End point x ( 1 to 127 ) available in association group
Change fuel type(2)
Used to Set / Change boiler fuel type to configure TPI cycle.
View fuel type(2)
View present boiler fuel type.
Lock/unlock
temperature set point
Disable / Enable set-point change using Up/Down buttons.
Role transfer(1)
Shift primary role to the new controller in network
Exit(3)
Exit from advance mode
Z-Wave Device Classes
Implemented Device Class
Generic
Multilevel Sensor
Specific
Routing_Sensor_Multilevel
Basic
Portable Controller
Command Classes
Supported
Description
Manufacturer Specific (V2)
Secure Controls (UK) Manufacturer ID, Device serial number
Version (V2)
Provides the version number of the firmware, hardware and supported
Command Classes.
Device Locally reset (v1)
Used to inform lifeline node that the device has been factory reset, and is
leaving the network.
Z-Wave Plus Info (v2)
Z-Wave Plus Version 1
Role Type - ROLE_TYPE_CONTROLLER_PORTABLE_REPORTING
1. Maximum time out for activity is 55 seconds.
2. Operation applicable if node available in association group 2.
SUPPORTED DEVICE AND COMMAND CLASSES
2
Node Type - NODE_TYPE_ZWAVEPLUS_NODE
Installer IconICON_TYPE_SPECIFIC_SENSOR_MULTILEVEL_AIR_TEMPERATURE
User Icon - ICON_TYPE_GENERIC_SENSOR_MULTILEVEL
Wake Up (V2)
Wakeup interval step is 60 second.
Minimum wakeup interval is 900 seconds
Maximum wakeup interval is 10 days
Default wakeup interval is 24 hours
Association Group Info (v1)
Group
No. Of Nodes
AGI Group Name
AGI Profile Name
1 1 Lifeline
Profile MSB AGI_PROFILE_GENERAL
Profile LSB AGI_GENERAL_LIFELINE
2 1 Sensor: Air temperature
SENSOR_ MULTILEVEL_
REPORT_TEMPERATURE
Association (v2)
Support two groups each can have maximum one node
Group 1(Lifeline)
Low battery Alarm Report
Multilevel Sensor Report
Device Reset Locally
Group 2
Multilevel Sensor Report
Set point Set
Multi Channel Association
(v2)
Device support single node with One endpoint to association group 2
Configuration (v1)
(Any change from default
configuration, will reduce the
battery life, zero configuration
means that feature is disabled)
Parameter Type
(sequential order)
No
Size
Byte
s
Units
Resolution
Min
value
Max
Value
Default
value
Delta Temperature
for Association
Group 2
1 1 ºC
0.1 0 100
10
Temperature report
Interval for
association Group 2
2 1 minute 1 0
255
30
Minimum Set Point
temperature
3 1 ºC 1 5
35
5
Maximum Set Point
temperature
4 1 ºC 1 5
35
35
Delta Temperature
for lifeline Group
5 1 ºC
0.1 0 100
0
Temperature report
Interval for lifeline
group
6 1 minute 1 0
255
0
Example: To configure Delta temperature to 2 °C. The value need to configured in
device is 2/0.1 = 20.
IMPORTANT: Controllers may only allow configuring signed values. In order to set
values in the range 128…255, the value sent in the application shall be equal to
desired value minus 256. For example, to set Delta Temperature to 130, it may be
needed to set a value 130−256=−126.
Multilevel sensor (v5)
Measure room temperature to 0.1°C resolution. But report as per its
configuration set.
Power Level (v1)
For network maintenance functionality
Firmware Update Meta
Data (v3)
For providing Over-The-Air firmware upgrades
Thermostat Set point (v3)
Used to directly read and control the current target temperature
3
LED type
LED colour
Pattern
Indication
Battery
White
1 sec on @ power up
Battery is healthy
Battery
Amber
1 sec on 60 sec off
Battery is low
Network
White
1 sec on 60 sec off
No network error
Network
Amber
1 sec on 60 sec off
Can’t able to reach associated node
Mechanical
Dimensions (LxWxD)
98 x 98.5 x 35mm
Mounting
Wall mounting to fit a single gang wall
box
Weight
157gms
Enclosure material
Thermoplastic, flame retardant HB
Environmental
Storage temperature
-20°C to 50°C
Operating temperature
0°C to 40°C
Environmental humidity range
0 to 95%
Atmospheric range
980 to 1035 hPa above mean sea level
Pollution degree
2
Ingress protection
IP30
Electrical
Battery specs
2 x AA LR6 alkaline, 2700 mAh
Battery life
2 Years
Battery rating
1.5 V each
Measurement
Temperature accuracy
±0.5°C for 0°C to 21°C
Europe & UK
868 MHz
RF range
100m line of sight in open air
Installation instruction
LED illumination
Technical Specification
4
Loading...