Secura QST25 Instruction Manual

Download

Page 1

QST

If you have any questions along the way, just give us a call.

INSTRUCTION MANUAL

We’ll Make It Stress-Free

1-800-359-5520 We’re ready to help!

Scan for easy install video

san.us/1140

Page 2

CAUTION: IMPORTANT SAFETY INSTRUCTIONS — PLEASE READ ENTIRE MANUAL PRIOR TO USE — SAVE THESE INSTRUCTIONS

Before getting started, let’s make sure this mount is perfect for you!

Does your TV

(including accessories)

weigh MORE than

35 lbs. (15.8 kg)?

What is your

wall made of?

Do you have

all the tools needed?

Ready to begin?

CAUTION:

No? Perfect – you may continue.

35 lbs.

(15.8 kg)

Perfect!

Tape

Measure

Please read through these instructions completely to be sure you’re comfortable with this easy install process. Also check your TV owner’s manual to see if there are any special requirements for mounting your TV.

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, contact Customer Service at

Yes? This mount is NOT compatible.

Visit secura-av.com or call 1-800-359-5520

(UK: 0800 056 2853) to ﬁ nd a compatible mount.

Drywall with

wood studs?

Pencil Level

drywall alone

Screw

CAUTION:

DO NOT

install into

driver

Electric

Drill

(12 mm)

Socket

Wrench

1-800-359-5520 (UK: 0800 056 2853).

Perfect!

7/16 in.

3/8 in.

(10 mm)

Wrench

indicated. This mounting system is intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in collapse of the mount and its accessories, causing possible injury.

Solid concrete or

concrete block?

Stud

Wood Stud Install

Finder

DO NOT exceed the maximum weight

Unsure?

Call Customer Service: 1-800-359-5520 (UK: 0800 056 2853)

1/8 in.

(3 mm)

3/8 in.

(10 mm)

Masonry

Concrete Install

Drill Bit

Awl

Wood

Drill Bit

CAUTION: Avoid potential personal injury or property damage!

● This product is designed for use in wood stud, solid concrete, and concrete block walls - DO NOT install into drywall alone

● The wall must be capable of supporting ﬁ ve times the weight of the TV and mount combined

● Do not use this product for any purpose not explicitly speciﬁ ed by manufacturer

● Manufacturer is not responsible for damage or injury caused by incorrect assembly or use

Hammer

Page 3

Dimensions

in.

[mm]

TILT

Page 4

M4 x 12mm

M6 x 12mm

M6 x 35mm

M4 x 35mm

M6 x 14mm

22mm

M6 / M8

M8 x 16mm M8 x 35mm

M8 x 20mm

Supplied Parts and Hardware

WARNING: This product contains small items that could be a choking hazard if swallowed.

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts!

NOTE: Not all hardware included will be used.

STEP 1 Parts and Hardware

Screws

(TV Bracket Extender)

03 x4

Nuts

(TV Bracket Extender)

04 x4

TV Bracket

01 x1

†

† Nylon locking bracket nuts are

poly-locks and will need to be forcibly tightened.

TV Bracket Extenders

02 x2

Only needed for TVs with 20.0 x 20.0

(7 7/8 x 7 7/8 in.) hole patterns

TV Screws

05 x4

06 x4

07 x4 08 x4

12 x4 13 x4

Washers

14 x4

09 x4

10 x4

11 x4

Spacers

Page 5

1/4 x 2¾ in.

STEP 2 Parts and Hardware

Fischer UX 10 x 60R

Wall Plate

Lag Bolts

For concrete installations ONLY

CAUTION: Do not use in drywall or wood

Concrete Anchors

Page 6

STEP 1 Attach TV Bracket to TV

inches

1.1 Measure Your TV Hole Pattern

Measure the width and height of your TV hole pattern in cm (see conversion chart below).

Record your measurements:

Width ______cm x Height ______cm

inches cm mm

3 7.5 75 4 10 100 7 ⅞ 20 200

inch dimensions are approximate

Page 7

1.2 Assemble Your TV Bracket

Determine which TV bracket configuration to use, A or B, based on your TV hole pattern measurements (W x H) from STEP 1.1.

TV Hole Pattern

Measurement

7.5 x 7.5

10.0

7.5

20.0

10.0 x 10.0

20.0 X 10.0

Dimensions in cm

10.0

TV Hole Pattern

Measurement

20.0 x 20.0

Dimensions in cm

20.0

These smaller hole patterns only use TV bracket 01. Do not use the two TV bracket extenders

and four nuts 04.

and four screws

7.5

Assemble TV bracket extenders

Secure using four screws 03 and four nuts

NOTE: Nuts 04 are poly-locks and need to be forcibly tightened.

3/8 in. (10 mm)

wrench

onto TV bracket

as illustrated.

in the corner holes shown.

Page 8

1.3 Select TV Screw Diameter 1.4 Select TV Screw Length

Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter (M4, M6 or M8) to use.

M6 M8M4

If your TV has a flat back AND you want your TV closer to the wall, use the shorter TV screws and no spacers 14.

Spacers 14 and longer TV screws are supplied to accommodate:

● Round/irregular back TVs

● TVs with inset mounting holes

● Extra space needed for cables

FLAT BACK ROUND BACK CABLESINSET HOLES

Standard configurations are shown. For special applications, or if you are uncertain about your hardware selection, contact Customer Service at 1-800-359-5520.

CAUTION:

Verify adequate thread engagement with your screw/ washer/spacer combination AND TV bracket (STEP 1-5).

- Too short will not hold the TV.

- Too long will damage the TV.

Too Short

Correct

Too Long

Page 9

1.5 Attach TV Bracket

Position your TV bracket configuration (A or B) over your TV hole pattern - making sure the bracket is centered over the TV hole pattern and level.

Install using the TV screw/washer/spacer configuration you selected for your TV.

CAUTION: Avoid potential personal injuries and property damage! DO NOT use power tools for this step. Tighten the screws only enough

to secure the TV bracket to the TV. DO NOT overtighten the screws.

IMPORTANT: Ensure TV bracket is securely fastened before moving on to the next step.

TV Bracket Conﬁ guration

(from page 7) Illustrated with spacers

Flat Back

TV Bracket Conﬁ guration

(from page 7) Illustrated with spacers

0509061007 08

121213

Round Back / Extra Space

Page 10

STEP 2A Attach Wall Plate

Wood Stud Option

CAUTION: Avoid potential personal injury or property damage!

● Drywall covering the wall, must not exceed 5/8 in. (16 mm)

● Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)

● Stud center must be verified

1. Locate your stud. Verify and mark the center of the stud by finding the stud edges using an awl, a thin nail, or an edge to edge stud finder.

2. Position the wall plate 15 at your desired height and line up the holes with your stud center line. Mark the hole locations.

3. Drill pilot holes using a 1/8 in. (3 mm) diameter drill bit.

IMPORTANT: Pilot holes must be drilled to a depth of 2 ¾ in. (70 mm). Be sure to drill into the center of the stud.

Max. 5/8 in.

(16 mm)

in. (70 mm)

2¾

1/8 in.

(3 mm)

Page 11

4. Install wall plate

using two lag bolts 16. Tighten the lag bolts only until they are pulled firmly against the wall plate.

CAUTION: Improper use could reduce the holding power of the lag bolt

NOTE: If needed, you can make small level adjustments to the wall plate 15 by loosening the bottom lag bolt 16 and shifting the wall plate 15

until level. Tighten the bottom lag bolt

Go to STEP 3 on PAGE 14.

when adjustments are complete.

. DO NOT over-tighten the lag bolts 16.

Page 12

STEP 2B Attach Wall Plate

CAUTION: Avoid potential personal injury or property damage!

Solid Concrete or Concrete Block Option

● Mount the wall plate assembly

● Minimum solid concrete thickness: 8 in. (203 mm)

● Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)

1. Position the wall plate 15 on the wall at your desired height. Level the wall plate template and mark the hole locations.

2. Drill two pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.

IMPORTANT: Pilot holes must be drilled to a depth of 3 in. (75 mm). Never drill into the mortar between blocks.

directly onto the concrete surface.

3 in. (75 mm)

3/8 in.

(10 mm)

Page 13

3. Insert two anchors 17.

CAUTION: Be sure the anchors are seated flush with the concrete surface.

4. Install wall plate 15 using two lag bolts 16. Tighten the lag bolts only until they are pulled firmly against the wall plate.

CAUTION: Improper use could reduce the holding power of the lag bolt

NOTE: If needed, you can make small level adjustments to the wall plate 15 by loosening the bottom lag bolt 16 and shifting the wall plate 15

until level. Tighten the bottom lag bolt 16 when adjustments are complete.

. DO NOT over-tighten the lag bolts.

Page 14

STEP 3 Hang TV onto Wall Plate

HEAVY! You may need assistance with this step.

TILT POSITION

IMPORTANT: The locking tab needs

to be in the unlocked position before attaching the TV to the wall plate 15.

Hang your TV in either the TILT or LOW PROFILE positions as shown.

LOW PROFILE POSITION

Page 15

TV Adjustments

REMOVING THE TV:

Remove any cables from the TV. Move the locking tab into the unlocked position and

lift the TV up and out away from the wall plate 15.

CAUTION: Avoid potential personal injuries and property

damage! Once the TV is on the wall plate 15, move the locking tab

to the locked position to secure the TV onto the wall plate 15.

Page 16

Thank you for choosing Secura! Please take a moment to let us know how we did:

Email us: info@secura-av.com

Call us: 1-800-359-5520

UK: 0800 056 2853

Milestone AV Technologies and its a liated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or su ciency of the information contained in this document.

Milestone AV Technologies • 6436 City West Parkway • Eden Prairie, MN 55344 USA 6901-002594 00