Page 1
All settings related to video capturing can be changed in the Capture settings menu. T o keep privacy at the highest level, the video capturing and
camera powering from VIDNET power supply are directly related. It also affects the camera powered from extra power supply . VIDNET will capture
video if this action is granted in the Capture settings menu.
Main Menu }Settings }Video settings } Capture settings
2. VIDEO CAPTURING SETTINGS
It is recommended to give an appropriate name to a camera. The system will use it to send information to
ALARMSERVER.NET or to SECOLINK PRO application . For next character possition press [] or [] key . To delete
a character move the cursor on wrong character and press [0]. Press [Ü] or [7] key for the next camera.
1
C01 CAM1
Name CAM1
VIDNET
User manualIntruder alarm system
Intruder alarm system with video module VIDNET on board is not a CCTV surveillance system that simply records
videos that are accessed by the system user. Rather, VIDNET is a complete video alarm system that sends a short
video clip with the alarm notification to the SECOLINK PRO app for immediate review and it can also link the video with
the central monitoring station (CMS). VIDNET delivers faster response to an actual crime scene because the user or
CMS operator filter out false alarms. The system should include at least one analog camera covering assets and key
entrance points where a thief, vandal, or trespasser could show up. Up to four analog cameras can be connected to
INTRODUCTION
Page 1
1. REGISTRATION OF THE ALARM SYSTEM IN ALARMSERVER.NET
ALARMSERVER.NET is simply a service platform that keeps in sync end user devices which have the SECOLINK PRO app installed with the
alarm system. Status (armed/disarmed, alarms, troubles), temperature in premises (measured by temperature sensors BT1, BP1, or keypads),
and video recordings made by VIDNET can all be monitored using the service. This platform is also useful to installers to remotely monitor alarm
system's performance and to remotely update system settings. This communication uses data service and charges may apply . Note: Y ou must first
register your system with a server before using ALARMSERVER.NET .
Main Menu }Settings }www.alarmserver .net
Mandatory settings:
This menu is used to register your intruder alarm system on ALARMSERVER.NET and to send any settings related to
communication. It is mandatory to register your system with a server, if SECOLINK PRO application will be used to
control the system via TCP/IP . After a successful registration go to www.alarmserver .net to create a free account.
Important! The registration on server process should be repeated if any settings described below are changed.
www.alarmserver .net
Registration on server
1
Reporting – in this menu the user can change settings for reports on ALARMSERVER.NET .
Periodic test – the module can send a test message periodically: every 10 min, 30 min, 1 hour, 6 hours, 24 hours, 48
hours or it can be disabled.
Technical info – the module can send technical information periodically: every 10 min, 1 hour, 24 hours, every 1
week, or disabled.
Every event – to view present status of the system, all new generated events (e.g. arming/disarming, alarms and
etc.) should be sent to ALARMSERVER.NET . This setting must be enabled, if SECOLINK PRO application will be used
to control the system via TCP/IP .
Event log – the event log could be sent periodically: every 10 min, 1 hour, 24 hours, every 1 week or disabled. This
menu disappears if Every event setting is Yes.
Motion detection – the system can send a list of violated zones during the predefined time period. This time period is
directly related to report sending period: every 10 min, 1 hour, 24 hours, every 1 week, or disabled.
Use GPRS as backup – if the communication with a server is not established via LAN, the system will try to
establish the connection with a server via GPRS (3G).
TCP control – this setting must be enabled, if SECOLINK PRO application will be used to control the system via
TCP/IP . Module will have a keep-alive connection with a server to ensure real - time control.
6
www.alarmserver .net
Reporting
Privacy settings – in this menu the user can change privacy settings.
Report user names – selecting an option Yes will allow the system to send user names to ALARMSERVER.NET ,
which can be viewed in SECOLINK PRO application. If No will be selected the application will show default system
names such as User 01 or User 02.
Report zone names – selecting an option Ye s will allow the system to send zone names, partitions and other
information (except user names) to ALARMSERVER.NET, which can be viewed in SECOLINK PRO application. The
application will show default zone names such as Zone 01 or Zone 02, if the user will select an option No.
Save event log – selecting an option Yes will allow the user to view the system's saved event log in the application.
Event log will not be seen with an option No.
7
www.alarmserver .net
Privacy settings
1
2
3
Privacy settings
Report user names
Report zone names
Save event log
Yes
Yes
Yes
Optional settings:
To remotely modify the existing system project, upload it to ALARMSERVER.NET using the Send project to server
menu. Uploaded project is automatically assigned to the installer who maintains the user's system account. An installer
can download the project from server to computer and modify it using the MASCAD software. To apply system
changes, the modified project should be uploaded back to the server. When this action is done, an installer should
notify the user to download the modified project to the system using the Receive prj. from server menu.
2
3
www.alarmserver .net
www.alarmserver .net
Send project to server
Receive prj. from server
This menu is used to manually send the event log to ALARMSERVER.NET. All event s stored in ALARMSER VER.NET
will be overwritten.
4
www.alarmserver .net
Send event log
5
www.alarmserver .net
Send technical info
This menu is used to manually send technical information to ALARMSERVER.NET .
1
2
3
4
5
6
Reporting
Periodic test
Technical info
Every event
Event log
Motion detection
TCP control
Every 10 min
Every 1 hour
Yes
No
No
Enabled
Page 2
If Video capture setting is set to Always, then the camera will always be powered.
There will be no video loss during an
alarm or when arming/disarming. The recorded video will start 2-3 seconds before the event and end 5-10 seconds
after the event.
It will be possible to record video at all
times in case of an alarm or other conditions as well as view live video stream.
If Video capture setting is set to When armed, then proceed to the corresponding arming mode sub-menu to mark
partitions. Press the [ENT] key to enter the menu, then press [#] to assign a partition to arming mode. Save changes by
pressing the [ENT] key. The intruder alarm system will supply power to cameras and will start capturing videos when
any of the selected partitions is armed in arming mode assigned to that specific partition. If the system is programmed
to record a video in the event of arming or disarming, then it will not be as long as it could be with Video capture set to
Always.
Camera video capture and power can be turned off using the Video settings menu (Main Menu }Controls }Video
settings). If this setting is set to Yes, then VIDNET will automatically supply the power to cameras and will start video
capture next time the system will be armed.
2
1
2
3
C01 CAM1
Armed in Away
When armed
Armed in Away [ENT]
[ENT]
[ENT]
a
[ENT]
a
Armed in Night
Garage
Armed in Stay
2nd floor
Armed in Max Away
1st floor
Video capture
2
C01 CAM1
Video capture Always
7
C01 CAM1
Start capt. when armed Yes
If Capture when alarming setting is set to Yes, then VIDNET will automatically supply the power to cameras and will
start video capture regardless of what is programmed in the Capture video when Armed setting, or if the power supply
for video cameras is manually turned Off. Video capturing will be turned Off when alarm is cleared.
8
C01 CAM1
Capture when alarming Yes
2-3 seconds. 5-10 seconds.
Event: alarm, arm/disarm,
motion, zone violation
Armed.
Video of 2-3
seconds is
available.
Disarmed.
Video is not
available.
Armed.
Video of 5-10
seconds is
available.
Camera is
turned off.
Video is not
available.
3. VIDEO RECORDING SETTINGS
All settings related to video recording can be changed in Recording settings menu. To correctly setup the video recording settings read the
instructions below.
Main Menu }Settings }Video settings } Recording settings
In case of an alarm in a selected partition, the video module will send the recorded video to ALARMSERVER.NET, or
save it to micro SD card. Press the [ENT] key to enter the menu, then press [#] to assign a partition to camera. Save
changes by pressing [ENT].
C01 CAM1
1
Alarm in partition [ENT]
1
2
Alarm in partition
a
a
2nd floor
1st floor
VIDNET
User manualIntruder alarm system
In the event of arming or disarming a selected partition, the module will send the recorded video to
ALARMSERVER.NET, or save it to micro SD card. Press the [ENT] key to enter the menu, then press [#] to assign a
partition to camera. Save changes by pressing [ENT].
In the event of an alarm from selected zones, the module will send the recorded video to ALARMSERVER.NET, or
save it to micro SD card. Press the [ENT] key to enter the menu, then press [#] to assign zones to camera. Save
changes by pressing [ENT].
Video can be recorded if selected zones are violated in spite of that system being armed or disarmed, or if there is an
alarm from this zone. The module will send the recorded video to ALARMSERVER.NET, or save it to micro SD card.
Press the [ENT] key to enter the menu, then press [#] to assign zones to camera. Save changes by pressing [ENT].
Video can be recorded if the module detects motion in the area that is being captured by the camera. The module will
send the recorded video to ALARMSERVER.NET, or save it to micro SD card.
Video can be recorded if the module detects loss of video stream from selected cameras. The module will send the
recorded video to ALARMSERVER.NET, or save it to micro SD card.
2
3
4
5
6
C01 CAM1
C01 CAM1
C01 CAM1
C01 CAM1
C01 CAM1
Partition arming
Partition disarming
Alarm from zone
Zone violation
Video loss
[ENT]
[ENT]
[ENT]
[ENT]
5
C01 CAM1
Motion detection Yes
[ENT]
1
2
3
4
Alarm in partition
a
a
a
CAM3
CAM4
CAM2
CAM1
Page 2
Page 3
Video module can be programmed to send recorded video files to ALARMSER VER.NET, or to save files locally to micro SD card (card content can
be accessed by use the software supporting files of the H.264 format). Storing video files on a server has many advantages. SECOLINK PRO
application installed on smartphones or tablets allows you to easily view files. Additionally, files can be viewed on any device's (smartphone, tablet,
or computer) browser that is connected to the Internet.
A user can participate in our V oucher system which includes storage rental for files and communication between an intruder alarm system, server ,
and end user devices (smartphone, tablet, or computer). Contact your system installer to get this code. TRIAL voucher will be activated
automatically when a new system is added to any user's account for the first time (see table below).TRIAL includes features like system control
over TCP/IP, push notifications, video clip storage, and review using an app or web browser's window. TRIAL period is 10 days. When this period
expires, TRIAL will be downgraded to IP VIDNET . IP VIDNET plan is free of charge and valid for unlimited time. An account can be upgraded to IP
VIDNET EXTRA. The subscription period could be one, two, or three years.
3. STORAGE SETUP
4. CREA TING A NEW ALARMSERVER.NET ACCOUNT
Main Menu }Settings }Video settings } Storage setup
Recorded video clips can be sent to ALARMSERVER.NET via 3G modem that is integrated to VIDNET module or
using LAN interface.
1
Storage setup
Send via LAN Yes
In case of LAN failure the module will use 3G modem and will send videos to ALARMSERVER.NET .
Note: This menu is visible if video sending via 3G is set to No.
All recorded videos can be saved to micro SD card (tested with micro SD cards up to 32GB in size).
2
3
4
Storage setup
Storage setup
Storage setup
Send via 3G
Backup via 3G
Save to SD
No
Yes
Yes
VIDNET
User manualIntruder alarm system
ALARMSERVER.NET voucher plans
System control over IP network,
push notifications to app
Recorded alarm video preview
in browser or using app
Other type video preview in
browser or using app
Video recording by
request
Voucher name
TRIAL (for 10 days) Yes Ye s Yes Yes
IP VIDNET (free of charge) Yes Yes, recent 1 video clip Not available Not available
IP VIDNET EXTRA Yes Yes, recent 10 video clips Yes, recent 10 video clips Yes
5. ASSIGNING USER'S APP TO THE SYSTEM
1. Run application SECOLINK
PRO and tap Let's start.
2. Enter your name and your
phone number. Choose Yes in
setting In use and enter details
related to login to server
ALARMSERVER.NET. Press
Done to continue.
3. Select an alarm system. Tap
and hold for more details. Press
Done to start data downloading
from the ALARMSERVER.NET
4. Enter system name and PIN
code. Use Encrypt PIN if SMS will
be used to control the system.
Check the Consists of the system.
Press Done to continue.
1. Go to www.alarmserver .net.
2. Click Register at the center of the page (skip steps 2 - 4, if user already have an account).
3. Click on Create account button on End User column.
4. Fill in required fields: name, country, e-mail, p assword, and system BI. To find system BI, please watch a video posted below these fields. Click
Register to proceed.
5. Login using your e-mail and password. Press Sign in to proceed. T o reset the password click Set new link.
6. Enter system name and location. System BI number entered during registration should be visible in the corresponding field. Press Save (on the
right) to proceed.
7. Added system will appear on the list. The TRIAL voucher will be automatically activated when a new system is added to any user’s account for
the first time.
Page 3
Page 4
VIDNET
Intruder alarm system
5. Enter SIM phone number which
is installed in the alarm system.
Determine which plans are
enabled in this SIM card.
6. Choose method of communication with the alarm system.
7. Choose which notifications will
be sent by the alarm system to the
application. Press Done to save.
8. Home screen of the app. It is
recommended to test it before
using the app. T ap Status.
9. Tap Video to view LIVE video
stream.
13. Tap whichever event to watch
an attached video.
14. Use the bottom menu to control
video preview. Tap on any video
screen to expand it.
15. T o return to home screen tap
few times.
16. Application is ready to use.
Enjoy!
10. LIVE video stream from the
cameras will be seen on screen.
T ap on any video screen to expand
it.
11. Tap to start video recording,
tap to turn on playback mode.
T ap to return to home screen.
12. All new system events are
stored in the menu Events, Users.
T ap on it to enter.
Kodinis Raktas UAB, manufacturer of SECOLINK Intruder Alarm System, of fers a Warranty for a term of twenty-four months. It declares,
that product VIDNET complies with essential EU directive and EU standards EN 50131-1 Grade 1, Class II; EN 50136-1; EN 50136-2;
EN 50131-10. For more information visit manufacturer’s website at www.kodinis.lt or www .secolink.eu for a complete text of declaration.
SECOLINK Intruder Alarm System is designed and manufactured in Lithuania.
SYSTEM COMPLIANCE AND WARRANTY
Rev.13/09/16_KF
Page 4
User manual
Loading...