Page 1
BP2: > 2 years
INSTALLATION
The BP2 detector provides the mo convenient and cost effective solution for security device is powerful and versatile enough to help solve even the
toughest, most labor intensive installation. The BP2 detector is compatible with wireless extension modules EXT116S or with built-in virtual modules EXT1 16SVM in P series control
panels P16, P32 and P64.
st reliable, protection. The
SECOLINK WIRELESS DETECTORS
SPECIFICATIONS
Model Passive infrared sensor (PIR sensor)
Dimensions (W x H x D) Ambient humidity
Built-in temperature sensor Pet immunity
Ambient temperature Battery
Battery life
BP2
54,8 mm x 100 mm x 39 mm
oo
-10 C - +55 C
0% - 70% Depends on firmware version of the detector: Lithium battery
½ AA, 3,6V
Operating frequency
1 = 868,30 MHz (EU)
9 = 915,30 MHz (AU)
Battery life of wireless detectors depends on the
environment, usage, and the specific wireless devices
being used. Factors such as humidity, high or low
temperatures, as well as large swings in temperature
may all reduce the actual battery life in a given
installation. When the battery is nearly dead (low battery
threshold voltage < 2,45V) , the detector will send a low
battery signal to the alarm system for the user to replace
it before it discharges completely.
1.Unscrew the self-tapping screw .
2.Remove the detector's top cover .
3.Observe correct polarity and insert the battery into the
battery holder.
4.Close the top cover and secure it with a self-tapping
screw.
5.Dispose of used batteries as per local regulations.
Caution: the detector will send a tamper message to the
receiver when housing is opened - the alarm can be
triggered.
BATTERY INSTALLATION/REPLACEMENT WIRELESS DETECTOR OPERATION TESTINGDETECTION PATTERNS
1
3b 4
Remove the plastic tab. Follow the instructions on a 2nd
page and enroll the detector into the system. After a
successful detector's enrollment close the top cover.
Use the screw to secure the top cover to the mounting
base.
T o test wireless detector operation enable the test mode
by doing a burglary zone test:
Normally a wireless motion detector idles 4 minutes after
last movement detection:
BP2 Wireless detector
Intruder alarm system
Installation manual
1
2
2 3
Pull the
plastic tab
LED
LED indicator is
enabled when the
pins are shorted
3a
Corner mount Surface mount
Use for swivel mount bracket
Detector's recommended mounting
height is 2,1 meters (+/- 20 cm). It is
designed to be mounted on surfaces, in
corners (3a), or installed in places where
it is necessary to use a swivel mount
bracket (3b).
Find a suitable location (place) for the
detector keeping in mind the warnings
below:
Keep away from heat source.
Do not expose to air drafts.
Do not install outdoors.
Do not obscure partially or completely
the detector's field of view.
Avoid direct sunshine.
Keep away from power cables.
Mount on solid and stable surface.
1,90 3,3 5,9 15m
2,1m
15m
0
5
5
10
15m
o
98
50 10 15m
10
~ 4 min ~ 4 min
TEST
STARTED
TEST
ENDED
~ 4 min ~ 10 sec
~ 10 sec ~ 4 min
Main menu }Test }Burglary zone test
Detector will enter the test mode after first movement
detection and will stay in this mode until the zone test will
end (see picture below).
Page 1
Page 2
Please act according to your local rules and do not dispose of your unusable alarm system or its components with other household waste. This
product utilization in EU is covered by European Directive 2002/96/EC.
ENROLLING
11
Service mode
System setup
Enable the wireless zone by changing Not used
loop type to any other loop type. If the system uses
a keypad produced before 2014, an installer is
obligated to change the loop type to NO/DEOL or
Vibration.
Advance to the next unlearned zone with keypad
keys [Ü] or [7].
11
Z01 Door
Name
Door
33
System setup
Zones
Z01 Door
Loop type
NO/DEOL
33
Z01 DoorZ01 Door
WL det. loop (zone) ID WL det. loop (zone) ID 201
44
Z01 Door
Address
06_1
33
Enter the zone address in MA_Z format, where MA
is a module address in the system and Z is a zone
number in the module.
Note: for wireless zones MA_1 – MA_8 the system
will automatically assign NO/DEOL loop type and
for wireless zones MA_9 – MA_16 the Vibration
loop type. Don't change the loop type of a zone!
Module address:
EXT116S - address 06 (default) or given during
the registration process;
Virtual module EXT116S address depends on the
control panel type:
P16 - address 12;
P32 - address 12 and 13;
P64 - address 12, 13, 14 and 15.
Enter wireless detector loop (zone) ID number and
press the [ENT] key to start enrolling. This field may
also be used for deleting the sensor from the
module.
When enrollment has started, immediately press
the tamper switch for a short period of time (~1 sec)
as shown in the picture. Y ou will feel a light click after
pressing the switch. The tamper switch is now
activated and the detector will transmit a tamper
message.
Done
Waiting for
WL detector
Wireless detector successfully enrolled. No
additional transmissions are needed for
confirmation.
BP2
Supports Wireless detector loop (zone) ID number
Passive infrared
sensor
(PIR sensor)
180
255
Built-in
temperature
sensor
Delete detector in
a specific zone
Delete all
detectors
in a specific
wireless module
All
All
181
254
BP2 Wireless detector
Intruder alarm system
Installation manual
BP2
Use
Wireless detector loop (zone) enrolling ID numbers
Rev.28/11/16_KF
Page 2
Kodinis Raktas UAB, manufacturer of SECOLINK Intruder Alarm System, of fers a Warranty for a term of twenty-four months. It declares, that
product BP2 complies with essential EU directives and EU standards EN 50131-1, Grade 1, Environmental Class II; EN 50131-2-2. For more
information visit manufacturer’s website www.kodinis.lt or www.secolink.eu for a complete text of declaration. SECOLINK Intruder Alarm
System is designed and manufactured in Lithuania.
System compliance and warranty
Used for Interior, Interior Night Armed, Follower,
Follower Night Armed zones. Use [] or [] to change
wireless PIR BP2 sensitivity: 1 pulse (the most sensitive
mode), 2 pulses, or Adaptive (the less sensitive mode).
Z01 DoorZ01 Door
PIR modePIR mode 1 pulse
1515
Loading...