Page 1
Manual
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
Flush-Mount Low-Profile
UFO Camera
Model
Video Output
Resolution
EV-122C-FVB3Q
NTSC
480 TV Lines
EV-6640-N3WQ
NTSC
600 TV Lines
EV-122C-PVB3Q
PAL
480 TV Lines
EV-6640-P3WQ
PAL
600 TV Lines
Small size - only 3” diameter
1
/3” Sony Super HAD II CCD
3.7mm Pinhole lens
Low 0.05 Lux rating
Lens rotates to nearly any angle
Low-profile design blends into nearly
any décor
Vandal-resistant metal housing
Page 2
ENFORCER Flush-Mount Low-Profile UFO Camera
NTSC
EV-122C-FVB3Q
EV-6640-N3WQ
PAL
EV-122C-PVB3Q
EV-6640-P3WQ
Type
Flush-Mount Low-Profile UFO Camera
Image sensor 1/3” Sony Super HAD II CCD
Resolution
480 TVL
600 TVL
Lens
3.7mm
Pickup
elements
NTSC
510x492 pixels
768x494 pixels
PAL
500x528 pixels
752x582 pixels
Sync
Internal
Video output
1.0Vp-p composite video, 75Ω
Minimum illumination
0.05-lux
S/N ratio
>48dB
Shutter control
Auto Electric Shutter (AES), 1/60~1/100,00 s
Gain control
Auto
White balance
Auto
Gamma correction
0.45
Operating voltage
12VDC ±10%
Current draw
130mA ±10mA
Operating temperature
-4°~122° F (-20°~50° C)
Dimensions:
Parts List:
Specifications:
1 x Camera
1 x Flange
1 x Base
1 x Ring bracket
3 x Mounting screws
1 x Manual
1 x DC Plug with
terminal block
2 SECO-LARM U.S.A., Inc.
Page 3
ENFORCER Flush-Mount Low-Profile UFO Camera
Before Starting:
Installation:
Overview:
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not mount the camera where it is exposed to rain or
other moisture, or in humid or dusty places.
4. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.
6. Do not drop the camera or subject it to strong vibrations
1. Run a 12VDC power supply wire and a video cable with
a male BNC connector to the wall or ceiling where the
camera is to be mounted.
2. Temporarily connect the camera to the 12VDC
power supply.
3. Temporarily connect the camera’s female BNC
connector to the video cable’s male BNC connector.
4. While watching the monitor, hold the camera against the
wall or ceiling by hand where it is to be mounted, then
turn the camera until it is certain that this mounting
location is correct. Use a pencil to mark the location.
5. Disconnect the 12VDC power supply and video cable.
6. Drill a 2
1
/4” (56m) hole in the ceiling or wall where the
camera is to be mounted.
7. Twist the flange off the base and remove the
camera ball.
8. Place the ring bracket behind the hole.
Note: Ring bracket is not necessary if mounting
directly to wall.
9. Push the base into the hole, and secure to the ring
bracket using the three supplied marking screws.
10. Run the power supply and video cable through the
wall or ceiling to the hole, and through the bracket
and base. Connect to the camera’s power and video
connectors.
11. Hold the ball in the base, and secure with the flange.
Do not tighten securely.
12. Apply the power to the camera. Watch the monitor
and adjust the angle of the lens.
13. Secure the camera by tightening the flange.
14. Do a final test of the video camera and monitor.
DC Plug with
terminal block
DC Jack
Female BNC
connector
Flange
Camera ball
Screw
(1 Shown, 3 included)
Base
Ring bracket
(inside the ceiling wal)
Flange
Base
Ring bracket
SECO-LARM U.S.A., Inc. 3
Page 4
ENFORCER Flush-Mount Low-Profile UFO Camera
M UFO_Camera_1206.docx
PICSN4
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a
period of three (3) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of
any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2012 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999
Website: www.seco-larm.com
E-mail: sales@seco-larm.com
The screen is blank.
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
The screen image is dim
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image has poor contrast.
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image flickers.
Change the position of the camera.
Troubleshooting:
The screen image is distorted.
Change the position of the camera.
The camera case is hot.
Check that the correct power supply is in use.
4 SECO-LARM U.S.A., Inc.
Loading...