SECO-LARM USA EV-1323C12DWQ, EV-1353B12DWQ, EV-1353C12DWQ, EV-132C-DW2Q, 1353B12DWQ User Manual

...

ENFORCER CCD IR DAY/NIGHT CAMERA MANUAL

TROUBLE SHOOTING

The screen is blank

The screen image is dim

The screen image has poor contrast

The screen image flickers

The screen image is distorted

The camera case is hot

IR LEDs do not turn on

IMPORTANT

Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.

WARNING

Stop using the camera if you see a malfunction like smoke or unusual heat, as it could cause fire or electric shock. Do not open the case of this device, as there are no field-serviceable components inside.

FCC COMPLIANCE STATEMENT

Information to the user: This equipment has been tested and found to comply with the limits for a class a digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

• Check that the camera is powered up.

• Check that the power supply’s polarity is correct.

• Check that the monitor is powered up.

• Check that the video cable connecting the camera to the monitor is connected properly.

• Clean the lens (using a soft, clean cloth).

• Check that the light source is adequate.

• Adjust the monitor’s contrast knob.

• Change the position of the camera.

• Check that the correct power supply is in use.

ENFORCER

VIDEO

MANUAL

1/3" CCD Color IR Day/Night Camera

Model

Number

EV-1323C12DWQ EV-132C-DW2Q EV-1353C12DWQ EV-135C-DW2Q

1/3" CCD B/W IR Day/Night Camera

Model

Number

EV-1323B12DWQ EV-1353B12DWQ

*All viewing angles are approximate

Video

Format

NTSC NTSC

PAL PAL

Video

Format

EIA

CCIR

Lens Size

4.3mm

2.9mm

4.3mm

2.9mm

Lens

Size

4.3mm

Viewing*

Angle

120

Viewing*

Angle

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.

NOTICE

The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors. Copyright © 2007 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.

C - MSECO-LARM

SECO-LARM

C - M

16842 Millikan Avenue, Irvine, CA 92606

Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326

., I c U.S.A., Inc.

U.S.A., Inc.

., I c

Website: www.seco-larm.com E-mail: sales

seco-larm.com

File:DT/DTP/IR_12LQseries_076.PMD

PITNW1

Weatherproof

®®

E M

SECO-LARM

E MSECO-LARM

Note: Products with model number that ends with "Q" or have a round green "Q" sticker represents RoHS compliant products.

®®

ENFORCER CCD IR DAY/NIGHT CAMERA MANUAL ENFORCER CCD IR DAY/NIGHT CAMERA MANUAL

Specifications

Type

Chip

Resolution

Pickup elements

Scanning system

Sync

Video output

Lens

Viewing Angle

Minimum illumination

Gamma correction

S/N ratio

Shutter control

Backlight compensation

Automatic gain control (AGC)

Enclosure

# of infrared LEDs

Max. LED range

Power source

Power consumption

Operating temperature

Dimensions

Weight

Dimensions:

21/4” (57mm)

/16” (68mm)

EV-1323C12DWQ (NTSC) EV-132C-DW2Q (NTSC) EV-1353C12DWQ (PAL)

EV-1323B12DWQ (EIA) EV-1353B12DWQ (CCIR)

EV-135C-DW2Q (PAL)

Color camera

1/3” CCD, Sony

420 TV lines

512 x 492 pixels (NTSC / EIA)

512 x 582 pixels (PAL / CCIR)

2:1 interlace

Internal

1V pp composite output, 75 ohms

EV-1323C12DWQ / EV-1323B12DWQ (4 3mm)

EV-1353C12DWQ / EV-1353B12DWQ (4.3mm)

EV-132C-DW2Q / EV-135C-DW2Q (2 9mm)

EV-1323C12DWQ / EV-1323B12DWQ (78o)

EV-1353C12DWQ / EV-1353B12DWQ (78o)

EV-132C-DW2Q / EV-135C-DW2Q (120o)

0.1 lux (LED off), 0.0 lux (LED on)

0.45

>50dB (AGC off)

Auto Electronic Shutter (AES)

1/60~1/100,000 sec. (NTSC / EIA), 1/50~1/100,000 sec. (PAL / CCIR)

100mA (IR off), 230mA (IR on)

14°~131° F (-10°~55° C)

31/16”(L) x 21/4”(D) (78 x 57 mm) (without sunshield)

>48dB (AGC off)

auto

IP68 weatherproof

Up to 40 ft. (12m)

12VDC±10%

110mA (IR off), 240mA (IR on)

16 oz. (454g)

/16” (65mm)

ENFORCER

B/W camera

1/3” CCD, A1 PROs

* All viewing angles are approximate

Infrared Day/Night

31/16” (78mm)

” (46mm)

” (14.5mm)

A. Camera B. Adjustable Sunshield C. Mounting bracket

F. BNC connector (female) G. Adjustment nut

H. Mounting holes D. 36” cord E. DC jack

NOTE: For additional pigtail connectors, inquire SECO-LARM’s EVA-F5521-3Q pigtail connector with 3-ft. length cable.

Use SECO-LARM’s included Pigtail Connector for easy installation and serviceability.

Important:

Do not cut DC Jack (E) or Video Jack (F) as warranty will be voided.

BEFORE STARTING

1. Please read this manual carefully and keep it for future reference.

2. Use the camera within given temperature and electricity limits.

3. Do not aim the LED light directly at the eyes when the LEDs are on.

4. Do not point the camera at the sun. Heat could damage the

camera, even when not in use.

5. Do not mount the camera in areas exposed to radiation, strong

magnetic fields, or strong electrical signals.*

INSTALLATION

. Run a 12VDC power supply wire and a video cable with a male

BNC connector through the wall to where the camera is to be mounted (if necessary).

2. Assemble the mounting bracket; then screw it into the back of the

camera. Make sure the mounting base is tightened to the bracket.

3. Temporarily connect the camera to the 12VDC power supply.

Do not cut DC jack or video jack as warranty will be voided. Use the included SECO-LARM’s pigtail connector.

4. Temporarily connect the camera’s female BNC connector to the

video cable’s male BNC connector.

5. While watching the monitor, hold the camera bracket against the

wall by hand where it is to be mounted, then twist the camera until it is certain that this mounting location is correct. Use a pencil to mark the location of the three screw holes in the bracket.

6. Disconnect the 12VDC power supply and video cable.

Important:

Do not remove label or open case as warranty will be voided.

Parts List

1 x IR camera 1 x Sunshield 1 x Mounting bracket 1 x Pigtail connector

ENFORCER

6. Do not open or disassemble the camera. There are no userserviceable parts inside.

7. Do not drop the camera or subject it to strong vibrations.

* Note: Many video monitors produce strong electromagnetic fields

close to the display CRT, especially when the monitor is turned on or during de-Gaussing, which occurs automatically with many monitors when the monitor is turned on.

7. Mount the bracket to the wall using the three included mounting screws. If the wall is made of dry wall, brick, or similar material, it may be necessary to use the three included screw anchors.

Reconnect the 12VDC power supply and video cable. Turn the monitor on, and make sure the camera is sending the proper video signal.

9. Adjust the camera angle: (a) Loosen and tighten the bracket’s thumb screw to turn the

camera and change its angle relative to the bracket. This ensures the camera is pointing in the right direction.

(b) Loosen and tighten the adjustment plate to rotate the camera

on its axis. This rotates the angle of the video image.

10. Tighten the bracket’s thumb screw and the adjustment plate so that the camera does not move, but not so tight that it cracks the case or bracket.

11. Do a final test of the video camera and monitor.

n rared Day/Nig t

3 x Mounting screws 3 x Screw anchors 1 x Manual

Hx3