SECO-LARM USA EV-122C-FVA3Q User Manual

ENFORCER FLUSH-MOUNT LOW-PROFILE UFO CAMERA MANUAL ENFORCER FLUSH-MOUNT LOW-PROFILE UFO CAMERA MANUAL

TROUBLE SHOOTING

The screen is blank

The screen image is dim

The screen image has poor
contrast

The screen image flickers
The screen image is distorted
The camera case is hot

• Check that the camera is powered up.

• Check that the monitor is powered up.

• Check that the video cable connecting the camera to the monitor is connected properly.

• Clean the lens (using a soft, clean cloth).

• Check that the light source is adequate.

• Adjust the monitor’s contrast knob.

• Change the position of the camera.

• Change the position of the camera.

• Change the position of the camera.

• Check that the correct power supply is in use.

ENFORCER

VIDEO

®

IMPORTANT

Users and installers of this product are responsible for ensuring this product complies with all national, state, and local
laws and statutes related to monitoring and recording audio and video signals.
responsible for the use of this product in violation of any current laws or statutes.

WARNING

Stop using the camera if you see a malfunction like smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no field-serviceable components inside.

FCC COMPLIANCE STATEMENT

Information to the user: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.

WARRANTY

This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a
period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines
that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damages of any kind to the purchaser or anyone else.

NOTICE

The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM
policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change
specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.

Copyright © 2008 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole
or in part, without the written permission of SECO-LARM.

SECO-LARM

will not be held

MANUAL

EV -122C-FVA3Q

1/3” CCD Flush-Mount

Low-Profile UFO Camera

®

R

E

C

R

O

F

N

E

With Concealed Screws and

Day/Night Operation

SECO-LARM® U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

Tel: [phone] Fax: [phone]

Website: www.seco-larm.com
E-mail: sales

@

seco-larm.com

file: FLUSH-MOUNT_IMU0407.PMD

®

PICSN4

SECO-LARMSECO-LARM

SECO-LARM

SECO-LARMSECO-LARM

®®

®

®®

ENFORCER FLUSH-MOUNT LOW-PROFILE UFO CAMERA MANUAL ENFORCER FLUSH-MOUNT LOW-PROFILE UFO CAMERA MANUAL

Specifications

Type

Chip

Resolution

Pickup elements

Sync

Video output

Lens (F2.5)

Minimum illumination

Shutter control

Gain control

Gamma correction

White balance

S/N ratio

Power source

Current consumption

Ambient temperature

Dimensions

*The EV-122C-FVA3Q incorporates day/night capability. This means that the camera switches to B/W mode at night.

Dimensions:

213/16"

(72mm)

21/4"

1

/8"

(3mm)

(56mm)

EV-122C-FVA3Q (NTSC)

Mini Flush-Mount Low-Profile UFO Camera
1/3" Sony Super HAD CCD
420 TV lines
510(H) x 492(V) effective pixels
Internal
1 Vp-p composite output, 75 Ohms.

3.7 mm
B/W 0.05 lux (day/night)*
Auto Electronic Shutter (AES), 1/60~1/100,000 sec.
Auto

0.45
Auto
>48dB
12 VDC
130mA±10mA

-4o ~ 122oF (-20o~50oC)
115/16" x 3" (49 x 77 mm)

Parts List

1 x Flush-Mount camera
1 x Flange
1 x Base
1 x Ring bracket
3 x Mounting screws
1 x Manual

115/16"

1"

(49mm)

(26mm)

115/16"

(49mm)

3"

(77mm)

Power cord included. For easy connection of
flush-mount ball or other camera to power supply.

To BNC

(From DC
camera)

Flange

BEFORE STARTING

1. Please read this manual carefully and keep it for future
reference.

2. Use the camera within given temperature and electrical limits.

3. Do not mount the camera where it is exposed to rain or other
moisture, or in humid or dusty places.

4. Do not point the camera at the sun. Heat could damage the
camera, even when not in use.

5. Do not mount the camera in areas exposed to radiation, strong

INSTALLATION

1. Run a 12VDC power supply wire and a video cable with a
male BNC connector to the wall or ceiling where the
camera is to be mounted.

2. Temporarily connect the camera to the 12VDC power
supply.

3. Temporarily connect the camera’s female BNC connector
to the video cable’s male BNC connector.

4. While watching the monitor, hold the camera against the
wall or ceiling by hand where it is to be mounted, then turn
the camera until it is certain that this mounting location is
correct. Use a pencil to mark the location.

5. Disconnect the 12VDC power supply and video cable.

6. Drill a 21/4” (56mm) hole in the ceiling or wall where the
camera is to be mounted.

Power adapter

with terminal

block

Screws (x 3)

Camera ball

Base

Camera

ball

Flange

Base

Ring bracket

(inside the

ceiling/wall)

magnetic fields, or strong electrical signals.*

6. Do not open or disassemble the camera. There are no user­serviceable parts inside.

7. Do not drop the camera or subject it to strong vibrations.

* Note: Many video monitors produce strong electromagnetic

fields close to the display CRT, especially when the monitor is
turned on or during de-Gaussing, which occurs automatically
with many monitors when the monitor is turned on.

7. Twist the flange off the base and remove the camera ball.

8. Place the ring bracket behind the hole.
Note:

Ring bracket is not necessary if mounting directly to wall.

9. Push the base into the hole, and secure to the ring bracket
using the three supplied machine screws.

10.Run the power supply and video cable through the wall or
ceiling to the hole, and through the bracket and base.
Connect to the camera’s power and video connectors.

11.Hold the ball in the base, and secure with the flange. Do
not tighten securely.

12.Apply power to the camera. Watch the monitor and adjust
the angle of the lens.

13.Secure the camera by tightening the flange.

14.Do a final test of the video camera and monitor.

Wall or
ceiling

Ring

bracket

Power

Connector

BNC

Connector